View Full Version : Gathering opinions on order of upgrades
As things stand, I have decided that my DR750 bug will have to wait until I find (1) the time, (2) the car, or (3) a 4-bolt/forged set-up to install in my 1G car.
In the meantime, I intend to do 13Gs and a downpipe, with whatever small tweaks necessary to optimize their installation, shy of a piggy-back or stand-alone.
I really want to end up with an AEM EMS, but I can't justify it until I can manufacture the time and opportunity to get the car to a proper tuner - my reasoning for the AEM over other options is my perception that, dialed-in, it can accommodate a more complete and flexible state-of-tune compared to a piggy-back - a piggy-back, while very capable, seems ultimately to be more of a compromise in a DD than I want, specifically in regard to rich/lean, cruise/performance issues.
I want as few compromises as possible in a car I drive for fun.
Anyway, I would like to get some ideas with an eye toward the 13G/downpipe scenario and stock ECU, and input on the question of the AEM, which, while expensive, is a more complete solution.
I think 300 or so AWHP should be doable; feel free to tell me how wrong I am, as long as you've got some tips for me.
Btw-
Also shopping DSM sidemounts, but I'm sure that can wait 'til after the snails and pipe.
CoreyB
03-30-2011, 10:44 AM
IMO if you are only going 13G for now you dont need AEM or a piggyback. Our cars came stock with 13Gs in Europe. I would go with the DSM sidemounts before going AEM.
IMO if you are only going 13G for now you dont need AEM or a piggyback. Our cars came stock with 13Gs in Europe. I would go with the DSM sidemounts before going AEM.
The European circumstance is the basis of my reasoning.
Poring over threads here and there indicates, however, that it may stretch the limits of the OEM ECU slightly, and if I run into a stumble on acceleration, or something like that, I might be able to address it in some way.
Anecdotally, the 'small problem/no problem' stories are about evenly split, to my recollection; I want to do everything I can to land on the 'no problem' side of things.
Along those lines, the only thing I've done to the car is an FPIK, recapped (Seth) ECU, and fresh 120K over the next couple of weeks (when I can shake loose), so I should be pretty solid to start - the only thing that could change things will be horseshit compression, but I don't think that's gonna be a problem.
CoreyB
03-30-2011, 11:18 AM
First mod should probably be a hotwire kit for the fuel pump and a walbro would be good as well.
First mod should probably be a hotwire kit for the fuel pump and a walbro would be good as well.
Ah, that's what I left out - waiting to hear about jrod's DeatschWerks fuel pump buy; don't want a whiny Walbro if I can help it.
Thanks for the reminder, Corey.
TonyM
03-30-2011, 02:59 PM
Meh, my Walbro has been fine, not too loud either.
I'd recommend:
-13T's
-AFPR
-Downpipe
-Open filter
-Hotwired walbro/other
With the AFPR you can crank the FP a little to give you some overhead on fuel without having to go with a piggyback or standalone. Bigger SMICs optional at that point. If you go piggyback and larger injectors, then upgrade your intercoolers.
Meh, my Walbro has been fine, not too loud either.
I'd recommend:
-13T's
-AFPR
-Downpipe
-Open filter
-Hotwired walbro/other
With the AFPR you can crank the FP a little to give you some overhead on fuel without having to go with a piggyback or standalone. Bigger SMICs optional at that point. If you go piggyback and larger injectors, then upgrade your intercoolers.
Already have the 13Gs, but the pump upgrade and AFPR should be sufficient to deal with any twitchiness arising from the bigger turbos, huh?
Can't think of any other turbo-related problems that would arise with the 13Gs, and if I get the DSM SMICs mounted, they're not big enough to affect spool much, are they?
TonyM
03-30-2011, 03:50 PM
DSMs won't affect spool.
my $.02:
-hotwired stealth pump
-ARC2/MAFT
-450cc injectors
-ebay tt downpipe
-ebay flex-section for downpipe
and the only reason i suggest the ARC2/MAFT is because once you've done it, you can take the 13g setup farther than you can with just a stock ecu. that...and you'll also be able to run 750's out of the box--until you afford to go AEM.
p.s.
i also vote for 13t's.
BaadVR4
03-31-2011, 10:34 AM
The most important upgrade in any engine that is going to see serious power mods later is a "bullet proof" short block. Stock components will only take so much additional stress, even when they are new. Older, already worn and sometimes stressed parts will take less. So, while it may seem too expensive to do the 4 bolt/forged/built short block first, since it doesn't add much fun initially, it frequently winds up making excellent economic sense. It is pretty much a "one time" expense to which you can add almost anything you want whenever you want. It really is the foundation for your eventual goals. I've seen many, many builds in my time (mostly US V-8 "street/strip" cars) that ended in the destruction of the bottom end because the owner went that "one step too far", thinking the engine's stock internals could handle "just one more small power boost". Our turbo boosted cars are even less forgiving as you add power to the stock components. The other issue with "sequential upgrades" it the loss of value when the various pieces are sold to do the next phase of the build up.
I know it seems like you're spending a LOT of money and getting little in return. But you are really only buying what you will buy eventually and a WHOLE LOT OF PEACE OF MIND between now and then. I would then spend the money for a fully prepared set of heads. Same logic applies, only in this case you will also see a LOT of performance increase. Once you have these two things in place, you can bolt on power adders and other mods to your heart's (and budget's) content. None of the money you spent will be lost in "upgrading" and you will be able to keep EVERYTHING else stock until you're ready.
Just my 1.5 cents worth.
my $.02:
-hotwired stealth pump
-ARC2/MAFT
-450cc injectors
-ebay tt downpipe
-ebay flex-section for downpipe
and the only reason i suggest the ARC2/MAFT is because once you've done it, you can take the 13g setup farther than you can with just a stock ecu. that...and you'll also be able to run 750's out of the box--until you afford to go AEM.
p.s.
i also vote for 13t's.
I'm sure hearing alot about 13Ts - how does that square with the stock ECU?
One of the reasons I want to go with the 13Gs is because I'm still running the original clutch (believe it or not); it drives like new - amazing - but it'll have to go at some point.
I figure the 13Gs can get me near 300 AWHP with a DP, and I honestly want to see how the car reacts to the bump in power.
Remember, I haven't done this stuff in years; I come from drag-car roots, and this car is more fun than the iron I used to drive.
When to go with the AEM is more a function of my learning curve than my wallet, actually, and, barring a huge windfall for a Ford GT, or being done in financially by bad fortune or Obamacare, I intend to pursue this platform in a couple different directions.
From the money standpoint, I don't know how much further I can go before Missus J insists on paint; if that happens, I guess I kinda have to sit still for it, huh?
I'd like to do what several of you have done, and collect a few of these to play with.
TonyM
03-31-2011, 10:41 AM
You already have the 13Gs so just rock those until you go bigger. 13G -> 13T isn't worth it. 9B -> 13T is certainly worth it.
The most important upgrade in any engine that is going to see serious power mods later is a "bullet proof" short block. Stock components will only take so much additional stress, even when they are new. Older, already worn and sometimes stressed parts will take less. So, while it may seem too expensive to do the 4 bolt/forged/built short block first, since it doesn't add much fun initially, it frequently winds up making excellent economic sense. It is pretty much a "one time" expense to which you can add almost anything you want whenever you want. It really is the foundation for your eventual goals. I've seen many, many builds in my time (mostly US V-8 "street/strip" cars) that ended in the destruction of the bottom end because the owner went that "one step too far", thinking the engine's stock internals could handle "just one more small power boost". Our turbo boosted cars are even less forgiving as you add power to the stock components. The other issue with "sequential upgrades" it the loss of value when the various pieces are sold to do the next phase of the build up.
I know it seems like you're spending a LOT of money and getting little in return. But you are really only buying what you will buy eventually and a WHOLE LOT OF PEACE OF MIND between now and then. I would then spend the money for a fully prepared set of heads. Same logic applies, only in this case you will also see a LOT of performance increase. Once you have these two things in place, you can bolt on power adders and other mods to your heart's (and budget's) content. None of the money you spent will be lost in "upgrading" and you will be able to keep EVERYTHING else stock until you're ready.
Just my 1.5 cents worth.
This ^ is probably the largest consideration with the current set-up; I know I have to go easy with a 1G cast-crank/two-bolt.
It would be really easy to be swayed by the idea of a "stock-block" unopened motor strapped with DR750s, approaching 600 AWHP...long enough to get it off the dyno and blow it up on the way home.
When I said I really like these cars, I meant it - the fact I have a Stealth hasn't curbed my urge for a VR4, and perhaps if I can find a nice 2G/3G specimen, that will be the killer-car.
2fnloud
03-31-2011, 12:39 PM
This ^ is probably the largest consideration with the current set-up; I know I have to go easy with a 1G cast-crank/two-bolt.
It would be really easy to be swayed by the idea of a "stock-block" unopened motor strapped with DR750s, approaching 600 AWHP...long enough to get it off the dyno and blow it up on the way home.
When I said I really like these cars, I meant it - the fact I have a Stealth hasn't curbed my urge for a VR4, and perhaps if I can find a nice 2G/3G specimen, that will be the killer-car.
I was under the impression that "unopened motor" was one that was 4-bolt with a forged crank (Matt's car), was EricTT's a 1st gen?
I was under the impression that "unopened motor" was one that was 4-bolt with a forged crank (Matt's car), was EricTT's a 1st gen?
Eric's Stealth is a 1G, but he's rolling a new OEM block, which means forged 4-bolt, I believe.
2fnloud
03-31-2011, 02:50 PM
I would have no problem trying to get 500 ponies out of a healthy 4bolt main engine.
Chris@Rvengeperformance
03-31-2011, 03:13 PM
Eric's Stealth is a 1G, but he's rolling a new OEM block, which means forged 4-bolt, I believe.
there are still 2 bolt forged crank engines sold because the 4 bolt needs supporting parts to drop in.
I did the sequential upgrades and I'll tell you I wouldn't do it again.
Pick a REALISTIC setup and buy parts until you have what you need.
I've run
9b/13G combo
Twin 13G
13G/DR650 combo
twin 13Ts
twin 19Ts
Safc I,
Emanage Blue
Emanage Ultimate
The best setups have of course been the 13Ts and the 19Ts, I haven't pushed the 19Ts to where they really outshine the 13Ts yet. The other turbo setups were fine, but when you are swapping turbos once a year your car just never seems to be all sorted out.
Same thing with the tuning. I've always felt like my car was running 3/4 assed. If I went to the emanage ultimate in the begining it'd be perfect.
If you go a part at a time the car will be a rolling project and that has really bothered me over the years.
I had a lot of fun, but I should've banked the cash and bought everything at once.
IF you want to run 13Gs with no fuel control just keep it under 15 PSI or less (you'll have to log) or you'll hit fuel cut or run dangerously lean. Honestly on 13Gs I'd just try to stretch what I could out of the stock injectors and be happy with that.
I would have no problem trying to get 500 ponies out of a healthy 4bolt main engine.
Damn straight.
I understand the change to 4-bolt/forged occurred sometime late in '92 production; I checked my VIN and it shows the car was mfred before whatever the date of the production change.
Again, though, I like the idea of more than one 3S, so I can drive one while I'm wrenching another.
2fnloud
03-31-2011, 03:21 PM
I too would love to have a second stealth R/T wouldn't even need to be turbo. I so want to semi-rice one with the Cianci fenders and duck tail. and lambo doors. Won't do it to mine, too nice to start with.
IF you want to run 13Gs with no fuel control just keep it under 15 PSI or less (you'll have to log) or you'll hit fuel cut or run dangerously lean. Honestly on 13Gs I'd just try to stretch what I could out of the stock injectors and be happy with that.
The leap to 13Gs/DP/AFPR, etc. will be done in one shot.
I have the HHH software on my netbook and have done a baseline see-if-it-works log.
I will be staying with stock injectors, maybe go with an MBC.
I anticipate logging is going to accelerate my learning curve; more of what I'm reading will make sense.
This place is a tremendous resource, but I live at the end of the frigging earth, so I'm gonna have to start picking this stuff up as I go.
I too would love to have a second stealth R/T wouldn't even need to be turbo. I so want to semi-rice one with the Cianci fenders and duck tail. and lambo doors. Won't do it to mine, too nice to start with.
Don't you touch the yellow car!
Also, please do everything you can to avoid the rice disease.
I love the looks of these cars, but for me, the whole point gets lost without the snails (nothing at all against NA owners, it's just not for me); I like the looks of a lot of cars, but I wouldn't necessarily buy a car for looks alone.
Half the reason I bought this thing was to avoid the belly-button-car label - total turbo production is 25K or so, right?
get better downpipe, EBC, A/F gauge, hotwire 255lph pump. imho, start from there. good start for 13Gs. do you have easy access to e85?
get better downpipe, EBC, A/F gauge, hotwire 255lph pump. imho, start from there. good start for 13Gs. do you have easy access to e85?
E85 is a definite no-go where I am.
Don't have a clue what the closest availability would be...I really am close to the end of the earth, you know - about 70 miles from Copper Harbor, which is at the tip of the Keweenaw Peninsula.
Civilization as you know it ends about 190 miles south of me - I have to drive about 165 miles to hit a 4-lane.
2fnloud
04-01-2011, 09:40 AM
Don't you touch the yellow car!
Also, please do everything you can to avoid the rice disease.
I love the looks of these cars, but for me, the whole point gets lost without the snails (nothing at all against NA owners, it's just not for me); I like the looks of a lot of cars, but I wouldn't necessarily buy a car for looks alone.
Half the reason I bought this thing was to avoid the belly-button-car label - total turbo production is 25K or so, right?
Don't worry, the Yellow one is not getting that. The tint was the ricest thing done and that is it. exterior planed changes are drop springs and rims. When I had to take her to the shop I could of changed out the hood, but after much debate, decided to leave her as is. I am designing a sound system for her as well. This system has been the toughest for me to design. I am taking weight into consideration.
For example I found an 8" sub that weighs only 4.8LBS each. I will be using four. As for an example of how I plan on my install:
My mid-range speaker install:
http://i202.photobucket.com/albums/aa177/2fnloud/1994%20Dodge%20Stealth/Audio%20%20Video/PICT3984.jpg
My center channel:
http://i202.photobucket.com/albums/aa177/2fnloud/1994%20Dodge%20Stealth/Audio%20%20Video/Project%20Center%20Channel/PICT4162.jpg
Link to my build log of the center channel (http://www.3sgto.org/f21/2fnoulds-build-log-2575.html)
I am very carefully designing a system that will suite my needs without destroying the interior of the car.
Don't worry, the Yellow one is not getting that. The tint was the ricest thing done and that is it. exterior planed changes are drop springs and rims. When I had to take her to the shop I could of changed out the hood, but after much debate, decided to leave her as is. I am designing a sound system for her as well. This system has been the toughest for me to design. I am taking weight into consideration.
For example I found an 8" sub that weighs only 4.8LBS each. I will be using four. As for an example of how I plan on my install:
My mid-range speaker install:
http://i202.photobucket.com/albums/aa177/2fnloud/1994%20Dodge%20Stealth/Audio%20%20Video/PICT3984.jpg
My center channel:
http://i202.photobucket.com/albums/aa177/2fnloud/1994%20Dodge%20Stealth/Audio%20%20Video/Project%20Center%20Channel/PICT4162.jpg
Link to my build log of the center channel (http://www.3sgto.org/f21/2fnoulds-build-log-2575.html)
I am very carefully designing a system that will suite my needs without destroying the interior of the car.
I like that - haven't started to think about a sound system for mine, yet; don't know how elaborate it would be unless I line up some replacement interior panels to butcher.
I also have a fairly decent Pioneer HU I could throw in, and I think that fact is making me a bit lackadaisical about doping it all out.
I think you should start a thread for yours...
2fnloud
04-01-2011, 09:53 AM
yeah sorry about that didn't mean to hi-jack.
yeah sorry about that didn't mean to hi-jack.
Not a problem - I really think you ought to start a thread, though - looks like you're doing something a bit special; I'd like to hear/see more....;)
E85 is a definite no-go where I am.
Don't have a clue what the closest availability would be...I really am close to the end of the earth, you know - about 70 miles from Copper Harbor, which is at the tip of the Keweenaw Peninsula.
Civilization as you know it ends about 190 miles south of me - I have to drive about 165 miles to hit a 4-lane.
then just move down south a little in to WI territory. we have (relatively speaking) plenty of e85 here.
I guess if you will just use 93oct than I don't think you need to upgrade your intercoolers yet. imho
then just move down south a little in to WI territory. we have (relatively speaking) plenty of e85 here.
I guess if you will just use 93oct than I don't think you need to upgrade your intercoolers yet. imho
Yeah, 93 is my best option, here.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.