PDA

View Full Version : Looking for some electrical wizards



Mike-92RT
03-27-2011, 03:36 PM
Some of you may have seen my Dimmer switch thread. Well that thread has died :(

I have found the wire that has shorted out, and i haven't checked the whole harness, so i dont know how far it goes. I unplugged all the plugs at the fuse box, and i see one plug with 2 green/white wires.

The dimmer switch's black/yellow wire ties in with the green/white wire at the radio connectors. So could some one tell me which green/white wire pin the dimmer switch is? They are side by side in the plug.

Mike-92RT
03-27-2011, 03:49 PM
http://i581.photobucket.com/albums/ss258/Mike92RT/fuse.jpg

One of the two circled in red, is the plug that has 2 green/white wires. One of them probably giving power to the rheostat.

Both seem perfectly fine. I dont wanna dig through the rest of the harness to remove the burnt wire, i just wanna replace it at the plug and run it on the outside of the harness, tape it so its safe from metal, so its quick and easy.

Steve '92ES
03-27-2011, 06:37 PM
Good luck with that. The green/white wire goes all over the place! It's the feed from the tail light relay that turns on just about everything, including the ashtray light, door switch light, dashboard lights, radio lights, footwell, lights, pretty much everything with a bulb in it. But to answer your question it looks like C71 pin 8 feeds the dimmer.
This though could be your problem:

The dimmer switch's black/yellow wire ties in with the green/white wire at the radio connectors.
I don't see where they tie together, nor does it make sense that they should.
The green/white is the hot feed to one side of the bulb, the black/yellow is the other side of the bulb and goes through the dimmer to ground. Tying them together would just jump right around the bulbs, tying power straight to ground through the dimmer.
Try separating those two wires and see what happens.

Mike-92RT
03-27-2011, 06:59 PM
http://i581.photobucket.com/albums/ss258/Mike92RT/wire.jpg

That is where they meet. The plug is what connects to the radio.

There is a random orange wire that connects the 2 together for some reason. I don't know why? It was there when i bought the car, it worked up until last year. Its gotta be there for a reason, though its definitely not factory.

Steve '92ES
03-27-2011, 07:41 PM
OK, I looked through the diagrams again, as well as some other stuff I have on the stereo wiring and there's no way those two should be connected. The stereo diagrams confirm that those are the same two wires mentioned before.
I don't know how it was working before or what else has been hacked in your wiring but that jumper has to go...
Hmmm. I wonder it it depends on how the dimmer was set? Turn the dimmer down enough maybe it won't blow up but turn it up and kapow? Maybe you bumped up the dimmer somehow then when you turned on the lights? Either way that jumper would explain why the dimmer is melting..

Mike-92RT
03-27-2011, 09:49 PM
well when i replaced the burnt green/white wire to where i THOUGHT it ended... i tested it to see if it worked, but i realized just today that its in the wrong pin where that orange wire connects. Before the orange wire was 2 wires spliced together for some reason.. which might have caused the short.. now i made it just one wire.

I will test it tomorrow to see if it works.

ictponder
03-28-2011, 02:48 AM
Just in case you are still having trouble. I had no dash lights for about a year and tried finding a short with no success. I ended up removing the dash completely to find nothing wrong but it has worked ever since I reassembled the dash.

The hot Green/White wire coming from the dash/dimmer is connector D(C-71) pin 8. I color coded the connectors where the wire goes to different locations in the car. This wire goes to every bulb/connector in the dash.
http://i90.photobucket.com/albums/k241/ictponder/Junction-Block-Front-Back.jpg

http://i90.photobucket.com/albums/k241/ictponder/Junction-Block.jpg

Mike-92RT
03-28-2011, 08:06 AM
so the blue one is the one i want... okay. I pulled almost every plug on the junction box to look at what wires they have.

The bottom image is the front of the box i believe? Where the fuses are?

Thank you VERY much.


EDIT:
by the way, to make this more interesting, there were no blown fuses, all my interior lights work, tail lights work, headlights work... etc.

ictponder
03-28-2011, 10:31 AM
so the blue one is the one i want... okay. I pulled almost every plug on the junction box to look at what wires they have.

The bottom image is the front of the box i believe? Where the fuses are?

Thank you VERY much.


EDIT:
by the way, to make this more interesting, there were no blown fuses, all my interior lights work, tail lights work, headlights work... etc.

The bottom image is the inside of the fuse box and where the circuits go.

Mike-92RT
03-28-2011, 11:47 AM
The bottom image is the inside of the fuse box and where the circuits go.

hmmmm okay, so if i wanted to take the easy way out, how would i do that?

I want to take a single wire from the radio connector plug, or from the rheostat black/yellow wire itself so it can work properly. Is this possible?

ictponder
03-28-2011, 05:12 PM
hmmmm okay, so if i wanted to take the easy way out, how would i do that?

I want to take a single wire from the radio connector plug, or from the rheostat black/yellow wire itself so it can work properly. Is this possible?

I tried everything and nothing worked until I removed the entire dash and inspected every single plug where that green/white wire went. It might not even be the hot side, it could be the ground (black/yellow) that shorted on the switch only. However, that wire is also shared throughout all the connectors in the dash.

Steve '92ES
03-28-2011, 06:07 PM
EDIT:
by the way, to make this more interesting, there were no blown fuses, all my interior lights work, tail lights work, headlights work... etc.
I'm confused now. I thought you said every thing's working now?
What happened when you moved the wire?
What about if you leave that radio connector unplugged?

Mike-92RT
03-28-2011, 08:42 PM
I'm confused now. I thought you said every thing's working now?
What happened when you moved the wire?
What about if you leave that radio connector unplugged?

My dash lights STILL don't work.
all my other lights turn on and work, just not my gauges. No fuses have been blown.

Mike-92RT
03-28-2011, 08:47 PM
I tried everything and nothing worked until I removed the entire dash and inspected every single plug where that green/white wire went. It might not even be the hot side, it could be the ground (black/yellow) that shorted on the switch only. However, that wire is also shared throughout all the connectors in the dash.

my dash is removed right now, the harness is split open so i could follow the green/white wire.

the black/yellow wire is fine going from the rheostat plug to the radio plug. Just the green/white wire is burnt.
Theres an orange wire that connects the black/yellow pin to the green/white pin on the radio plug. Look at the pic i posted on the first page.

I JUST put the upper dash back in, half-ass to see if the dash lights turn on, which they STILL don't... im getting a little frustrated here. lol

Steve '92ES
03-28-2011, 09:50 PM
Theres an orange wire that connects the black/yellow pin to the green/white pin on the radio plug.

Did you try taking that jumper out?
Also, do you have the dimmer plugged in? The dash won't light without the dimmer.

Mike-92RT
03-29-2011, 02:19 AM
i haven't tried taking the jumper out yet... i have the dimmer plugged in every time i test it. Turn the key to II, turn the headlights on just to make sure.. still no dice :(

95gto
03-29-2011, 11:24 AM
i haven't tried taking the jumper out yet... i have the dimmer plugged in every time i test it. Turn the key to II, turn the headlights on just to make sure.. still no dice :(

That harness appears to be an aftermarket radio harness that is INCORRECTLY wired. Your dimmer wire (black/yellow) and your illumination wire (green/white) should not be shorted together, period. You may have killed your rheostat. Separate the two wires and see if that fixes your issue.

Most aftermarket radio's have either a dimmer or an illumination wire, not both. And unfortunately not every manufacturer marks them the same. If you leave those wires unhooked you just eliminate the disply dimming when you turn your parkinglights on.

Mike-92RT
03-29-2011, 11:38 AM
That harness appears to be an aftermarket radio harness that is INCORRECTLY wired. Your dimmer wire (black/yellow) and your illumination wire (green/white) should not be shorted together, period. You may have killed your rheostat. Separate the two wires and see if that fixes your issue.

Most aftermarket radio's have either a dimmer or an illumination wire, not both. And unfortunately not every manufacturer marks them the same. If you leave those wires unhooked you just eliminate the disply dimming when you turn your parkinglights on.

You know what... that actually kind of makes sense now. The orange wire used to be 2 orange wires spliced together, and then jumped the 2 pins together, which the orange wires were poorly connected. Which i think think has caused the short.

Also you are right, my Rheostat IS fried, one of the solenoids on the Rheostat's circuit board melted, and a LOT of smoke poured out the dash. Luckly right when that happened i immediately turned the car off.

Mike-92RT
03-29-2011, 12:27 PM
Heres an update video taken at around 10:30am this morning

http://www.youtube.com/watch?v=KFpFmwRewUw

Steve '92ES
03-29-2011, 02:50 PM
You know what... that actually kind of makes sense now.

LOL! How come it makes sense when HE says it?!?! :Sobbing:
Anyway, are you still using the damaged dimmer?
If you are using the new dimmer, could it have been damaged as well?
Now that you have that jumper out let's re-check voltages at the dimmer connector.
Unplug the dimmer, then with your meter set to volts connect the black probe to the black wire on the harness.
With the lights on use the red probe to check for voltage on the black/yellow and the green /white wires.
If you do not get any voltage try moving the black probe to a ground under the dash and try again.

While you have the meter out let's test out the dimmer. With the meter set to OHMS
check between pin 1, where the black/yellow wire would plug in, and pin 2, where the black wire would plug in. I'm not sure what the value should be but you should get something, and it should change when you turn the knob.

Mike-92RT
03-29-2011, 03:14 PM
Damaged dimmer was thrown in the garbage. I'm using another one that i found in a junk yard (rare in Ontario lol).. I dont know if its damaged or not, i just assumed it was good.

I wish i knew some one in town here, that i know personally, that owns a 3S.. just so i can test their rheostat in mine... but theres only a few in town, and they're all old farts.

I'll do the voltage tests and get back to you guys.

Steve '92ES
03-29-2011, 03:29 PM
but theres only a few in town, and they're all old farts.
Keep that up I'll yell at you to get off my lawn... ;) ;) ;)

Mike-92RT
03-29-2011, 04:43 PM
HAHAHA, sorry mate.

Anyways i did a voltage test.
http://i581.photobucket.com/albums/ss258/Mike92RT/IMG00146-20110303-1330.jpg
i used the 20k setting and here were the results.

black/yellow wire = 0.3
green/white wire = 0.3
black wire = 4.6

Steve '92ES
03-29-2011, 04:54 PM
Voltage my friend, Voltage!
Set the meter to 20 in the DCV area.

95gto
03-29-2011, 05:08 PM
^ Beat me to it

I believe you just used a resistance setting to perform a voltage test.

So lets start over:
Step 1) unplug the dimmer/rheostat
step 2) set the meter to DCV-20
step 3) turn on the parking light/headlight switch
step 4) place the red probe on green/white and black probe on black, record the voltage
step 5) place the red probe on black/yellow and the black probe on black, record the voltage

Mike-92RT
03-29-2011, 05:21 PM
ahhh sorry man. I'm not really good with electrical lol.

Here are the results for the 20 in the DCV area.

black/yellow = 11.24
green/white = 11.24
black = 0.05

dash lights still won't come on, with and without the radio harness plugged in.

Steve '92ES
03-29-2011, 05:27 PM
OK, so
you measured from the black/yellow to the black and got 11.24
and
you measured from the green/white to the black and got 11.24
What did you measure to the black to get 0.05?
Or did you measure all three to ground?

Mike-92RT
03-29-2011, 05:32 PM
i measured all to a ground..... i guess its different lol... i will measure both wires to the black wire now

Mike-92RT
03-29-2011, 05:37 PM
Here are the results for using the black wire.

black/yellow = 11.16
green/white = 11.16

Steve '92ES
03-29-2011, 05:52 PM
Just an odd though here but when you put the dimmer in did you try turning up the knob to make sure the lights were bright enough to see?

Try putting the dimmer back in and check those voltages again with the dimmer hooked up.
Move the knob around and see if the voltage on the black/yellow wire changes.
If you feel the dimmer getting warm SHUT IT OFF!!

95gto
03-29-2011, 06:06 PM
Voltage on both wires means that the wiring appears to be fine. It would indicate a bad dimmer/rheostat though which is a pain.

Mike-92RT
03-29-2011, 06:06 PM
knob was turned up all the way.

readings are:

black/yellow = 11.94 (went to 11.90 as i turned the knob off)
green/white = 11.14

car won't start due to no gas lol.. i can't charge my battery at home, so you'll see the readings slowly go down.

95gto
03-29-2011, 06:07 PM
i measured all to a ground..... i guess its different lol... i will measure both wires to the black wire now

the black wire is a ground wire, so measuring voltage to it and measuring voltage to ground is basically the same thing.

Steve '92ES
03-29-2011, 06:28 PM
the black wire is a ground wire, so measuring voltage to it and measuring voltage to ground is basically the same thing.
Unless the black wire burnt up along with the dimmer. I wanted to make sure we still had a ground connection there.

Voltage on both wires means that the wiring appears to be fine.
Unless those two wires are still shorted together somehow. Hard to say without putting a load on it which is why I wanted to put the dimmer back in. (under load the black/yellow should read less than the green/white)


black/yellow = 11.94 (went to 11.90 as i turned the knob off)
That's not good. Either the dimmer is toast or the wires are still shorted.
Try testing the dimmer.
Unplug the dimmer
Put the meter on 2k
on the dimmer measure between pin 3 (were the black/yellow wire goes) to pin 2 (were the black wire goes) while turning the knob up and down.

Mike-92RT
03-29-2011, 06:47 PM
sorry, i misread the volt meter... plus i have a bad memory. I went and retested and heres my OFFICIAL results lol.

black/yellow = 10.90 (10.95 with the knob on)
green/white = 11.16

Steve '92ES
03-29-2011, 06:56 PM
That's better, but I'd still like to see it change more.
Go ahead and try that test on the dimmer switch.

Mike-92RT
03-29-2011, 06:59 PM
just the dimmer itself? with no plug in it?

Steve '92ES
03-29-2011, 07:06 PM
Yup,
Unplug the dimmer
Put the meter on 2k
on the dimmer measure between pin 3 (were the black/yellow wire goes) to pin 2 (were the black wire goes) while turning the knob up and down.

Mike-92RT
03-29-2011, 07:11 PM
I get a reading of 046 and 047 when moving the knob up and down.

Steve '92ES
03-29-2011, 07:19 PM
Just checking, are you on the ohms setting (2k) or are you still on DCV?

Mike-92RT
03-29-2011, 07:19 PM
ohms setting (2000k) if thats what you mean? lol

Steve '92ES
03-29-2011, 07:30 PM
Sorry, I meant 20k.
2000k is too high. Try it at 20k then again at 200 ohms. (200, not 200k)

Mike-92RT
03-29-2011, 07:36 PM
with those settings, i don't get a reading at all.... nothing. Just a 1 on the left side of the screen.

Steve '92ES
03-29-2011, 08:00 PM
I think your dimmer is crap.
Try putting a jumper in the dimmer harness between the black/yellow and black wires and see if the lights come on.

95gto
03-30-2011, 03:27 PM
Unless the black wire burnt up along with the dimmer. I wanted to make sure we still had a ground connection there.

That's all good and fine but I was answerings the OP's question about the measurements being different. Are they different, no. In both cases you are measuring voltage on two wires with a direct reference to ground. Did the measurements validate the ground wire, yes. To be honest though I can't even think of a scenario with his failure mode that would cause the ground wire to burn up.



Unless those two wires are still shorted together somehow. Hard to say without putting a load on it which is why I wanted to put the dimmer back in. (under load the black/yellow should read less than the green/white)


I used the phrase "appear to be good" in case he still had an issue somewhere else. I wasn't saying he was out of the woods, I was saying he was likely out of the woods. Given how the circuit works and where his wire damage occured I would say its much more likely that wires aren't shorted together elsewhere. Especially considering the dispersion of the wires in the harness, its not like they run directly next to each other through out the dash wiring.

The jumper test should provide the evidence necessary to confirm an issue somewhere else in the wiring. If the lights work when he jumps the black and black/yellow together it would say that the dimmer is the problem.

Steve '92ES
03-30-2011, 04:13 PM
:sigh: I'm afraid sometimes the tone of my posts come off differently than I mean them to. I wasn't trying to argue with you, or "correct" you, I was just trying to explain my reasoning. More thinking out loud than anything. My apologies if it seemed otherwise.

Mike-92RT
03-30-2011, 08:01 PM
So i am to plug-in the Rheostat, then stick a pronged light bulb in both either power wire, and the ground to see if the bulb lights up?

Steve '92ES
03-30-2011, 08:37 PM
So i am to plug-in the Rheostat, then stick a pronged light bulb in both either power wire, and the ground to see if the bulb lights up?
Are you talking about the rheostat test procedure in the manual? If so then no. They want you to unplug the dimmer and bring it under the hood and hook it up to the battery as shown in the diagram.
You can try it but I'm not sure it will tell you any more than ohming it out with the meter did.

I think what both 95GTO and I are suggesting is that you try jumping the black and black/yellow wires together to see if that gets your dash lights to turn on. Just cut off a couple inches from that rat's nest you pulled out, strip a bit off each end, and stick one end into pin 2 (the black wire) and the other end into pin 3 (the black/yellow wire) of the connector the dimmer plugs into (instead of the dimmer). Turn on the lights and see what happens...
If the dash lights work with the jumper that would pretty much prove the dimmer is shot.

95gto
03-31-2011, 11:26 AM
Are you talking about the rheostat test procedure in the manual? If so then no. They want you to unplug the dimmer and bring it under the hood and hook it up to the battery as shown in the diagram.
You can try it but I'm not sure it will tell you any more than ohming it out with the meter did.

I think what both 95GTO and I are suggesting is that you try jumping the black and black/yellow wires together to see if that gets your dash lights to turn on. Just cut off a couple inches from that rat's nest you pulled out, strip a bit off each end, and stick one end into pin 2 (the black wire) and the other end into pin 3 (the black/yellow wire) of the connector the dimmer plugs into (instead of the dimmer). Turn on the lights and see what happens...
If the dash lights work with the jumper that would pretty much prove the dimmer is shot.


What he said.

If you connect the black/yellow wire to the black wire in the dimmer harness you are completing the circuit for the dash lights. If everything is good with your wiring the dash lights will come on with the headlight switch, they will just be full bright. If the lights don't come on it means you have wiring issues elsewhere and you probably blew the tail light fuse in the process.

If the lights work when jumped together but not with the dimmer plugged in it means you have a bad dimmer switch.

95gto
03-31-2011, 11:28 AM
:sigh: I'm afraid sometimes the tone of my posts come off differently than I mean them to. I wasn't trying to argue with you, or "correct" you, I was just trying to explain my reasoning. More thinking out loud than anything. My apologies if it seemed otherwise.

No worries

Mike-92RT
03-31-2011, 01:46 PM
well boys, it looks like i have more wire to replace near the fuse box..... ughhhhh... do you guys know how to remove the part of the harness above where the steering column bolts into?

95gto
03-31-2011, 02:41 PM
The easiest way to get to that wiring as far as I know is to pull the whole dash out.

I'm guessing you jumpered the black/yellow to the black wire with no results? Did it blow a fuse?

Mike-92RT
03-31-2011, 11:26 PM
no, nothing turned on, no fuses blew.. i leave the dash unbolted to check if my lights work... if not i can just unplug it, and remove it easily again.

95gto
04-01-2011, 10:15 AM
no, nothing turned on, no fuses blew.. i leave the dash unbolted to check if my lights work... if not i can just unplug it, and remove it easily again.

And for this test you connected the black/yellow and black wire in the dimmer harness via a jumper correct?

Mike-92RT
04-01-2011, 10:56 AM
yup, i had a jumper wire going from the black/yellow wire, to the black wire, at the back of the connector plug

95gto
04-01-2011, 04:37 PM
I just went through your dimmer switch thread and have some new questions:

1) the box in your video with the green wire that is connected to nothing is in fact an aftermarket alarm, what brand is it?
2) Did the car's gauge lighting work fine until the faitful day you pushed the pop up button?
3) was the headlight pop up button plugged in when you did the jumper wire test?

Mike-92RT
04-01-2011, 08:41 PM
I just went through your dimmer switch thread and have some new questions:

1) the box in your video with the green wire that is connected to nothing is in fact an aftermarket alarm, what brand is it?
2) Did the car's gauge lighting work fine until the faitful day you pushed the pop up button?
3) was the headlight pop up button plugged in when you did the jumper wire test?

1.) it doesn't say anywhere.. i thought it was factory :( lol
2.) Yes the dash lights worked until i pressed the pop up button. I DID fiddle around with the radio a LOT, before i pushed the button.
3.) No, the pop up button wasn't plugged in during the test. But the pop up button still works.

95gto
04-05-2011, 03:13 PM
If you shorted the black/yellow wire to ground, aka jumped it to the black wire like we said, but you still didn't get any illumination it would suggest a persisting issue with your wiring.

Take a look at the stereo harness connector where you found the melted wire. I know you replaced the melted green/white wire but I would verify that you still aren't experiencing some shorting within the harness connector itself.

Mike-92RT
05-09-2011, 12:20 AM
UPDATE!!!

i know its been a while, but i've been very busy to work on my car. Now that i had a chance, i have finally found out the green/white wire is burnt all the way to the fuse box.

I still don't know what plug it goes into, to plug into the fuse box. I have to cut more into the protective harness tape.

I know the green/white wire splices off in 2 different spots before the fuse box, the other wires that are attached to the circuit are not damaged, to let everyone know.