View Full Version : OK, fuel pressure slowly loses pressure...
Sin'sVr4
03-26-2011, 12:32 AM
So, i was having the issue that when I start the car, it would run then immediatley shut off like it was killing itself. So tried it a few times, same deal. So, i turned the car on ran to the engine bay to look at my fuel pressure gauge and it was slowly losing pressure? So, I checked all my connections, fuel rail, fuel loop, fuel fitler, fuel pressure regulator...all good to go. pulled the fuel pump, checked all connections, looked ok, nice and tight.
btw, when i turn the car to"on" u can hear the walbro whine.
Ok, continue..I left the fuel line lose to see if the pump was pumping fuel, turn the car over, checked yup fuel was being pumped out. Hooked it all back up nice and tight, cranked it...started then dies right away, fuel pressure slowly losing pressure. Is my pump bad? why all of a sudden after the night before it ran great and all i did was park it in the garage?
Any one tell me y its doing this? Please? :confused:
Mike
Intropy
03-26-2011, 01:49 AM
It's normal to slowly (and even not-so-slowly) lose pressure after the car dies, especially with aftermarket stuff. If you're really concerned about it, apply 12v to the pump directly and see if you maintain pressure while it's running. If so, it's probably not the issue.
AEM right? Are you set up to connect to it? Check for errors - if you use AEMTuner the "Troubleshooting" tab (hidden by default) is a good place to look first.
green-lantern
03-26-2011, 01:55 AM
You got to have some hoses off or something. You have had nothing but trouble the last few days. Go over the engine bay with a fine tooth comb. Check the vac hoses.
Sin'sVr4
03-26-2011, 02:01 AM
the pressure goes from 57psi to about 16psi with the key in the on psition. If i bump it it does the same thing. ive checked all hoses paul, nothing is off. ill post a vid of it and you can see what it does. probably have to post it tomm. But if the pump is bad, how can i test if its good? like i said, it whines so i know it is priming itself when i turn the key to on. I just did the relay bypass but wont check ill tomm (baby sleepin)
I just dont understand how it was perfectly fine and then now this
Intropy
03-26-2011, 02:10 AM
the pressure goes from 57psi to about 16psi with the key in the on psition.
You drop from 57 to 16psi? How quickly? That's a pretty big dump - OK if we're talking 30-60 seconds or something, but not immediately.
Get yourself set up to read that AEM. It could be something as simple as a bad sensor. When the car is cranking, the AEM uses the crank injector time table to determine how much fuel to inject. But once the car is running (stat running channel = ON) it will switch to other calculations based on sensor inputs.
Sin'sVr4
03-26-2011, 02:14 AM
about 20-30 secs to drop that far estimate
Intropy
03-26-2011, 02:19 AM
about 20-30 secs to drop that far estimate
Honestly I'd say that's OK. Not ideal, but I doubt it's your problem.
Sin'sVr4
03-26-2011, 02:21 AM
ok well hooked up to my aem andwhat am i looking for?
Intropy
03-26-2011, 02:40 AM
Look for problems in the error channels - "Error MAP" and such. I would also see where in the process it's dying. Does it actually start ("stat running" = on, "time after start" channel starts ticking)? Does it get far enough to turn on O2 feedback ("O2 FB Status")?
Sin'sVr4
03-26-2011, 02:42 AM
it starts tehn dies after it sounds like its gonna idle. i cant run it until tomm. so for now ill have to wait to test till tomm.
Steve '92ES
03-26-2011, 04:08 AM
Not to sidetrack Sin here but that's not exactly right.
The relay that turns on the fuel pump (part of the MFI) has two coils, either one of which can turn on the pump.
One coil is connected to the starter relay, the other to the ECU.
When you start the car the starter relay turns on the first coil, starting the fuel pump.
After that the ECU turns on the second coil, and keeps it on after you let go of the key as long as it gets CAS pulses.
The pump should start as soon as you crank.
Other than that though you're right. With stock wiring or even with most hotwire setups the pump shouldn't run with just the key turned to run.
Intropy
03-26-2011, 04:37 AM
Also sounds like you've got it wired up wrong. With a stock setup the pump doesn't start until the ECU gets a pulse from the CAS.
The EMS can prime the pump for some user-defined period of time at key-on.
The fuel system could be tighter but it's irrelevant as long as pressure is OK while the pump is running. We're just talking about idle here.
I don't suppose the weather cooled recently? With E85 you might need to enrich a little more. You can always add some fuel and see if it improves the situation at all. If nothing else that might give you a clue about what's going on. Obviously, save your existing cal before you mess around.
But definitely check voltages from your sensors and make sure that they look sane and that engine load is being calculated properly.
Sin'sVr4
03-26-2011, 11:59 AM
wether has actually been warmer...50-mid 60's. I think the pump might be shitting itself. Im gonna vid what happens and log it
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.