View Full Version : Having some fuel pressure issues.
92EuroDiamante
03-19-2011, 06:17 PM
Hey everyone. I took my car out for the spring and am having some fuel pressure issues. Equipment is as follows.
Walbro 2xxlph fuel pump (forgot the exact number, the one everyone uses)
Charging and grounding wiring upgraded.
Fresh alternator that I rewound for higher output
Fresh battery.
I have not hotwired the pump, in the D you have to drop the tank to get to the pump, it would be a mess if not necessary.
I used to enjoy 40 something psi at idle and and good fuel pressure across the board.
Now I am getting very low fuel pressure, sometimes nearly 0 at idle, and sometimes pretty high.
I can start the car, let it warm up at idle with the low fuel pressure, then as I turn the key back to turn the car off (to ON or ACC position) The fuel pressure climbs right back up. In the ACC position I hear the relay click and fuel pressure jumps up further.
Any ideas? not sure if I am missing something like not putting this pump on stock wiring or something.
92EuroDiamante
03-19-2011, 07:51 PM
played around with it some more.
Basically any accessory kicks it down to nearly no fuel pressure at idle, Fans, Bottle heater, even locking the doors!
Im getting 14.6v at idle.
GTOJOE
03-19-2011, 11:18 PM
So you have done the fuel pump hotwire? sounds like somehting in your acc wiring has a short or something and is drawing too much power which is robbing power from your fuel pump. Run a hotwire and see if that improves anything but I would be looking for what is causing the voltage issues. you need to check the voltage to the pump when you turn on any of the offending circuits.
92EuroDiamante
03-19-2011, 11:34 PM
No fuel pump hotwire. I didnt need it initially.
I will check for voltage monday hopefully, and do the hotwire at that time. A big project on the diamante because unlike the 3s you've gotta drop the fuel tank and not just the compartment in the back.
Im wondering about the power robbing idea. It makes sense, its just that basically anything causes it to go to zero. Things like the fans and bottle heater which are direct wired with a switch do it, but so do things that are part of the cars stock wiring still, like lights, and door locks.
x2percentmilk
03-20-2011, 12:30 AM
Hmm, id be worried about shorts and grounds. I cant really provide any specific things to check, but thats got to be it. If the ground for the pump is bad it could give reason for the electricity to flow elsewhere when available, ie: when you use the accessories. Other grounds could be bad limiting totaly current, shorts cause similar issues, etc etc.
92EuroDiamante
03-21-2011, 04:00 PM
I spent a while last night trying to find an electrical problem and couldnt. I disabled the lighting, all of the accessories and the accessory harness I made for fans, bottle heater and audio and it still had the same issue. If I turn the car off and leave the key in I can hear the relay clicking and the fuel pressure jumps up a few points after that so I know that is working.
I just pulled the tank and pump and everything looks good. Connections are solid.
Im wondering if its a bad pump.
Im off to figure out a way to hotwire this thing. Probably gonna have to remove the whole trunk to find the stock wire grrrr.
92EuroDiamante
03-21-2011, 08:13 PM
I just put everything back together, all wiring done correctly, as it was the first time. All fuel lines like new, no leaks.
If it was the fuel pump it wouldnt start right up and drive fine under normal rpms (under 3k) right?
I havent pushed it because I dont want to damage anything.
Guess im gonna try another fuel sender, anyone in the chicago area have one I can test?
It very well could be the pump. Non authentic Walbro's have some serious build quality issues and the market is so flooded with them that retailers are often unaware they are selling knockoffs. I would say fuel pump first if your accessories weren't affecting things- that points to a wiring issue. You may want to try replacing the in-tank power and ground wires or at least check the voltage getting through them. (at the in-tank fuel pump connector).
x2xtreme360
03-21-2011, 09:01 PM
Check voltage at the power wire to the pump. Turn on all accessories and check it again. Also, check the ground cable for any type of voltage drop. Go from the ground pin right to the negative battery terminal. The reading should be very low, 300mA or less to be exact.
92EuroDiamante
03-22-2011, 10:21 PM
Thank you for the advice :)
Gonna check the voltage soon. I wanted to yesterday but the wire is under my trunk mold so I didnt have time to remove it. I figured its best to check it there and not right off the relay.
Ground problems can be maddening. Sometimes it seems that electricity has a mind of its own - and it hates you.
A systemic and disciplined approach to troubleshooting will pay dividends. It can be time consuming, but ultimately it's the only way to do it. Otherwise you risk chasing your own tail.
And frequently, the problem is in a non-obvious area.
DG
92EuroDiamante
03-28-2011, 03:44 PM
Hey guys, I got the trunk pieces out, traced the wire and got a reading at idle.
Im getting 9.9v to the pump at idle, which seems generous compared to what some are getting on stock wiring.
Im gonna go see if I can find a bad ground or something that could be causing this.
Did a little research on the pump and walbro clones.
According for all the things to look for on authentic ones it appears to be a genuine unit but who knows?
You might as well go ahead and hotwire it. That will make things a little easier to diagnose. I don't think many retain the stock wiring with aftermarket pumps. The best place to test the pump voltage is at the in-tank connector. To do that, you need to remove the pump assembly from the tank, get the multimeter on the prongs of the pump connector, and cycle the pump. Best way to cycle the pump for this is with mmcd or some other electronic means. You can also turn the key, but that seems dangerous. I think there may be a diagnostic connector near the battery to cycle the pump.
I'm pretty sure walbro's flow drops considerably with any reduction in voltage.
92EuroDiamante
03-28-2011, 07:45 PM
You might as well go ahead and hotwire it. That will make things a little easier to diagnose. I don't think many retain the stock wiring with aftermarket pumps. The best place to test the pump voltage is at the in-tank connector. To do that, you need to remove the pump assembly from the tank, get the multimeter on the prongs of the pump connector, and cycle the pump. Best way to cycle the pump for this is with mmcd or some other electronic means. You can also turn the key, but that seems dangerous. I think there may be a diagnostic connector near the battery to cycle the pump.
I'm pretty sure walbro's flow drops considerably with any reduction in voltage.
I just finished hotwiring it. Im getting great voltage now but still 0 to 10psi of fuel pressure at idle and then the fuel pressure climbs right up once I turn the key back a click (cut off the engine)
Im testing the voltage about 1ft before the plug. My plug is right above my fuel tank which sits flush with the undercarraige so it is the best I can do without removing the fuel tank.
The logical conclusion from all this diagnosis is bad but not completely failed fuel pump right?
I dont think my fuel pressure sender is bad, because it shows higher readings once the engine is off.
You can test the fuel pressure sender with a Mitivac.
DG
J. Fast
03-29-2011, 04:38 AM
Mityvac: Mityvac Catalog Images (http://www.lincolnindustrial.com/asp/distributors/access/WebPhotoArchive/Mityvac_Web/index.htm)
More cool fluid toys! Mityvac (http://www.mityvac.com/pages/distributors.aspx)
I just finished hotwiring it. Im getting great voltage now but still 0 to 10psi of fuel pressure at idle and then the fuel pressure climbs right up once I turn the key back a click (cut off the engine)
Im testing the voltage about 1ft before the plug. My plug is right above my fuel tank which sits flush with the undercarraige so it is the best I can do without removing the fuel tank.
The logical conclusion from all this diagnosis is bad but not completely failed fuel pump right?
I dont think my fuel pressure sender is bad, because it shows higher readings once the engine is off.
I don't quite understand what you mean. Are you accessing the pump from the underneath instead of inside the trunk? There is an access door under the spare tire. I had somewhat similar symptoms and it was due to the ground wire in the tank being corroded. I had 12.5V to the top of the fuel pump assembly, but only about 3.5V getting to the pump itself.
92EuroDiamante
03-29-2011, 11:07 PM
I don't quite understand what you mean. Are you accessing the pump from the underneath instead of inside the trunk? There is an access door under the spare tire. I had somewhat similar symptoms and it was due to the ground wire in the tank being corroded. I had 12.5V to the top of the fuel pump assembly, but only about 3.5V getting to the pump itself.
I am doing this on a Diamante. Same driveline as a 3000gt but with a sedan body. Because of this the only way I can access the pump is by dropping the fuel tank because the fuel pump access is on top of the fuel tank. That is the closest I can get with the car running. The wires to the tank look fine. The car has less than 40k and has never seen snow other than on the driveway. If a new pump doesnt work I will have to test it with the car on a lift and the pump suspended underneath.
Ouch, what a hassle. If you change the pump you can put 12V to the connector on top of the assembly and make sure the same voltage is registering at the connector below just to be safe. I also added an additional clean ground from the chassis to the pump when I had that issue.
92EuroDiamante
04-02-2011, 07:50 PM
So I swapped in a known good working fuel pump and guess what?
Same exact problem. I would be inclined to believe the fuel pressure gauge/sender is bad but then why does it show fuel pressure when the engine is off but the key is on.
I got the balls and revved it up and it it shot straight up fine.
So I attempted some redneck dianostics.
I slowly unscrewed the fuel pressure sender as the car was running and as it begun to turn a got a high pressure spray of fuel....
Off to find a manual fuel pressure gauge!
TUFFTR
04-03-2011, 08:24 PM
So your gauge was faulty? jesus christ....unreal...
Are you running the gauge in car or in the engine bay?
92EuroDiamante
04-03-2011, 09:53 PM
It is an external gauge pulling a reading right off the rail. The gauge itself is in the car.
Well Im not surprised it stopped working, the surprising things are:
Its almost brand new and a good quality unit,
It gave an accurate reading with the engine off but went to zero with the engine on.
It gave a convincing display of a dying fuel pump. When this started it swung between 40 and 20 and continued that till I got it home.
92EuroDiamante
04-04-2011, 12:08 AM
I dont think so
I wired it according to the instructions and it worked well for a year and maybe a hundred miles.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.