PDA

View Full Version : Funky wiring issue.. I think.. maybe..



Rocket
03-13-2011, 03:47 AM
Ok while waiting on some stuff to come in for the engine I decided to get the new dash overlays wired into the car along with the new center cluster gauges. I eliminated the A-pillar pod which was crap and I hated :)

The center cluster works perfect, lighting wise that is, since I don't have the sensors in the bay yet. I have to replace the boost gauge this fall when I replace the defroster vents. You'll understand with the picture in a few.

The problem has come with the main cluster overlays. I tested them on my 12v power supply before ever putting them on the main cluster. Worked like a champ. When I installed them into the car I hooked them into the wiring just above the plug for the dash lighting rheostat. The wires there are Green/White stripe Black/Yellow and Black.. The Green is the 12v power, Black/Yellow is the rheostat ground that adjusts the brightness of the lights and black is chassis ground. (As long as I have read the manual correctly plug D-40). I wired the 12v+ for the overlays to the Green/White and the ground to the black wire. When I first turned them on the worked perfectly. BUT (here it is) after cycling them a couple of times the overlays didn't light. Rest of the dash lights were good, just the overlays didn't light.

I was fooling around with the dimmer assembly and pow they turned on. (This is where it gets odd to me). I unhooked the dimmer rheostat and cycled the lights and they work flawlessly. I put the rheostat back in and they come on intermittently. Once they are on they stay on, but the don't always come on. I worried the solder job I did had a cold solder joint so I cut the ground side and went straight to a known good chassis point. Same problem, with the rheostat plugged in intermittent on the lights, without it plugged in they light every time. Power going to them shows 11.6v. The rest of the dash lights work just fine with the rheostat plugged in. Sometimes if I play with the rheostat, or the housing of the rheostat they will pop on. Every time it is unhooked they work flawlessly. I was hoping to get the bottom of the dash all put back in today, but this has me stumped.

I could pull the main cluster back out and try to wire them into the lighting there and see if that fixes it, but not sure why that would fix it.

Could it be since the battery is just a tad low, the extra draw from having the rheostat plugged in is enough to drop the voltage below the minimum required by the reverse glow overlays? It may be fixed by just topping the battery off, or having the car running (not for another week at least).

2387

FluffyCow
03-13-2011, 07:48 PM
Sounds almost like the dimmer switch is dirty inside, causing intermittant c ontact since the overlays are LEDs(I'm assuming). I have a similar issue in my 87 RamCharger, where the dimmer switch sometimes causes my LED illumination to not turn on, and if I fiddle with the switch it turns on and stays on. How to go about testing or fixing that, though, I haven't the faintest idea.

Rocket
03-13-2011, 10:26 PM
Yeah kinda what I was wondering. The LEDs in the center cluster and the back lighting for the dash works ok, just the LED on the reverse glow overlays are being a pain. If the dimmer is unhooked they work awesome. But I can't ground them anywhere with the dimmer plugged in and get them to work.

green-lantern
03-13-2011, 10:46 PM
Your ringlands are broken. Tear the engine down and replace the pistons.

Roybatty
03-13-2011, 10:52 PM
Your ringlands are broken. Tear the engine down and replace the pistons.

LOL. Trolling!

Sent from my Eris using Tapatalk

x2xtreme360
03-14-2011, 01:53 AM
What are the connections on the overlays? The way the stock wiring works is if the lights are on and you unplug the dimmer switch, ALL the dash lights should go out. The black/yellow wire that controls the rheostat is a variable ground wire.

Rocket
03-14-2011, 02:22 AM
The center cluster lighting is wired to D-09 Pin-8 for + and Pin 1 for -. They operate flawlessly.

The main cluster is an indiglo reverse glow set. Has a positive and a ground going to it. I wired the positive to the (D-40 pin 4)green/white and the ground to the (D-40 Pin 2)black chassis ground on the dimmer. (they have their own dimmer). I have even run the ground from the overlays directly to chassis. If the switch is plugged in I have only occasional lights on the main cluster overlays, but with it unplugged they work just perfectly. The dash lights themselves do react like you would expect, they don't work if the dimmer is unplugged. I will go over tomorrow and take a video and try to post it up.

It just seems odd to me that going directly to chassis for a ground and using the power going to the dimmer, that the lights wouldn't come on correctly every time. I get the engine back in it and get it running maybe the problem will go away with the voltage running above 11.5v. I was just hoping to have this fixed and the knee panel put back in place :)

(note: the only things affected are the overlays:fuel, tach, speedo. The odometer etc, are still on the stock connections.)

Rocket
03-14-2011, 02:23 AM
I checked the ringlands too :P

x2xtreme360
03-14-2011, 02:26 AM
If you want to use the stock dimmer then use the black/yellow wire to ground the overlays instead of the solid black ground wire. Sounds like you have a break somewhere in the wiring that is causing intermittent issues... either that or the overlays are bad.

Rocket
03-14-2011, 02:46 AM
I would have thought if the overlays are bad then it wouldn't make a difference on the dimmer being hooked to the connector at all. Just seems odd.

I wired them to the chassis ground because they have their own dimmer built in. I didn't want the voltage to fluctuate on the ground side. I have even hooked them directly to the chassis. Same problem. <shrug>

Rocket
03-15-2011, 12:15 AM
Ok decided to go ahead and solder it all back up and deal with it once the car is running and I have 13+volts on the system The lower the battery gets the more flakey it gets. Call the project good for now, finish buttoning up the dash and tear out the passenger seat to run the hotwire to the fuel pump next :)