PDA

View Full Version : 2 bolt with forged crank worth it or just go 3.5L? Relability needed at 600hp.



Gearheadvr4
03-04-2011, 08:26 AM
Wanted to post here too since I usually get better answers on this site... I have a bit of a dilemma. I've got a perfectly fine turbo JDM 2 bolt with 57k. The engine ran great and the bearings looked brand new. All stock motor. I also have a 120k 4 bolt non turbo with normal wear for that mileage. Runs great too.

Keep in mind I have a power goal of about 600 and want as reliable as I can get since it's my daily driver. I will not push that power all the time, I plan to have an everyday boost level and a corvette killer level.

I've done everything else on these cars besides engine internals. Never plastigauged or swapped pistons ect. Scares me a bit since I've seen the results of poor engine builds.

Would it be worth it to swap the cranks so I could have a forged crank in the 2 bolt? What would be involved? My other option is a 3.5l but I cannot find anyone that has a ready to drop in motor. A 3.5l would be a much better fit for my 16g td05.

PearlWhiteR/T
03-04-2011, 12:39 PM
I would say you would be more than safe using your 2-bolt with a forged crank and the 3sx Arp main stud kit:
3SX Custom ARP Main Stud Kit for 91-92 TT/VR4 2-Bolt Mains*-*Mitsubishi 3000GT*/*Dodge Stealth Parts (http://www.3sx.com/store/comersus_viewItem.asp?idProduct=29426)

Can't say how involved the work is to pull an engine on our cars either as I've never done it myself. I know people have run kits similar to that on a 3.0 block.. pry would be some lag for sure though. If you aren't dead set on td-05's... some billet Dr650's or even 750's would be a great choice without having to swap out manifolds and worry about lag.

J_Parker
03-04-2011, 05:42 PM
Pulling an engine in our cars isn't all too bad as people make it seem. I can do it in about an hour with a good mindset, and available tools. With some ARP main studs you should be fine at that power level with the two bolt.

With a 16G kit you will have some lag, not horrible, but you will notice it. If you can, and want to see the full potential of those TD05's I would most certainly go for a 3.5L. Sometimes they're pretty tough to track down, but they pop up every now and again at very good prices.

If at all possible too, why not swap rods/pistons from your 2 bolt into the 4 bolt block and have some room to expand in power potential, if you ever decide to try for more than 800hp :p Doing the engine internals is pretty intimidating at first glance, but just walk into it with confidence. As long as you have a clean environment and some common sense you'll do fine!

Gearheadvr4
03-04-2011, 06:40 PM
Pulling an engine is no big deal, can do if in few hours. That's not the issue.

The 4 bolt is just an NA block so that means no oil squirters and whatever other differences there may be. If I swap pistons that would mean honing the cylinder walls right?

KeithMac
03-04-2011, 06:46 PM
My stock 2 bolt has handled all the abuse I can throw at it over 6 years now, I think it`s done very well!.

Knock from bad tuning is the biggest killer of the 2 bolts IMHO.

Gearheadvr4
03-04-2011, 08:53 PM
What level are you running at? With 780cc injectors you have to be very close to what my goals are. I want 600 and to be in the high 10s or low 11s in the 1/4.

KeithMac
03-05-2011, 03:19 PM
I haven`t dyno`d it, best trap was a 117mph so far but I haven`t managed to do a clean run with no clutch slip yet!.

I run 20% Methanol in tank, greatly increases octane/ knock resistance for me (but I have to run 15% more M20 than straight petrol for a given load range).

Still on a single Walbro so that`s the limiting factor at the moment, got all the bits to go dual pump which will be happening this year with my OS Geiken RC3 clutch.

I`ve always run Methanol injection or Methanol mix in tank when drag racing/ prolonged boost runs and that`s why it`s still in one piece I think!.

If you tine carefully I think you should be fine at 600awhp but just make sure you don`t start knocking especially in summer with the hot air temps.