View Full Version : New STRI Xline gauges
x2xtreme360
03-01-2011, 11:12 PM
Just thought I'd share my new dashboard look. Yes, the floor is indeed on the top... took the pics upside down:p I had to do some extensive modifying to the stock bezel to get them to fit the way I wanted them to. Used bondo and painted flat black. Rigged up my own mounting bracket as you can see in one of the pics. Thanks to Terry from Maximal for getting these for me. The center vents will utilize water temp, boost, and eventually a wideband.
http://i89.photobucket.com/albums/k226/X2Xtreme360/SDC10423.jpg
http://i89.photobucket.com/albums/k226/X2Xtreme360/SDC10424.jpg
http://i89.photobucket.com/albums/k226/X2Xtreme360/SDC10421.jpg
http://i89.photobucket.com/albums/k226/X2Xtreme360/SDC10427.jpg
I'm going to tap into the stock power and ground wire from the stock harness for the old gauges. Does anyone know (with experience) if there will be too much current flow to supply the power and ground for all 5 gauges?
Maximal
03-02-2011, 10:36 AM
Pics are blocked here at work but I'll have to check them out when I get home. Assuming you got the ones that went out Monday already?
x2xtreme360
03-02-2011, 02:32 PM
Pics are blocked here at work but I'll have to check them out when I get home. Assuming you got the ones that went out Monday already?
Certainly did. Thanks for the fast shipping.
Maximal
03-02-2011, 08:52 PM
They look good! Decided to pull the dash for the install? I did mine without it and it wasn't as bad as I thought. Of course I went with 60MM and just pressed them in from the outside. Your custom bracket would make it pretty tough to install it without removing it.
CoopKill
03-02-2011, 09:00 PM
They look good! Decided to pull the dash for the install? I did mine without it and it wasn't as bad as I thought. Of course I went with 60MM and just pressed them in from the outside. Your custom bracket would make it pretty tough to install it without removing it.
Do you have pics of the 60mm installed? Would like to compare.
__________________________________________________ ____________________
Tapatalk Bitches! :transform:
bluzvr4
03-02-2011, 09:28 PM
^x2 would like to compare as well
x2xtreme360
03-02-2011, 10:33 PM
I've had the dash out for a few months now honestly. I've gotten my time down to about 45-50 minutes to get the entire dash out from start to finish so it's not that bad.
DocHoliday
03-03-2011, 12:02 AM
Is there any fully digital gauge set?
No needles or numbers or anything.
Maximal
03-03-2011, 09:41 AM
Not the greatest pic and these are the DSD series instead of the X-Line like Brent has. Like I said they push in from the outside so they don't sit in as far but still have that there from the factory look.
https://lh6.googleusercontent.com/_4tAgKC3U8lM/TW-aQFY6WNI/AAAAAAAAAHs/3WYMr7CDRlc/s640/IMG_20100821_170502.jpg
I can probably grab better pics if you guys needed them.
bluzvr4
03-03-2011, 12:15 PM
did u ever make a thread on how to do this? i love the way those look in both cars but dont want to take my dash out so the push ins seem alittle more my style.
Atrosity
03-03-2011, 01:15 PM
I highly recommend dying the dash black if you have it pulled out! I simply love mine. It always has a glossy armor all shine, doesn't peel or anything.
http://i52.photobucket.com/albums/g19/Atr0sity/2.jpg
Maximal
03-03-2011, 01:31 PM
did u ever make a thread on how to do this? i love the way those look in both cars but dont want to take my dash out so the push ins seem alittle more my style.
I think there's writeup on here somewhere. Between the glove box, gauge cluster, and center vents you can get to most of the screws needed to get the stock gauges out. I actually broke mine to get them out. After that you just wire up the new gauges and press them into the openings.
x2xtreme360
03-03-2011, 02:06 PM
Bluz, dash removal is incredibly straight forward and simple to do with only basic tools. If you ever end up having to do it (doing gauges w/o removing the dash is a PITA) then you should have NO issues doing it.
Atrocity, pretty!
B-Man
03-03-2011, 02:11 PM
Supposedly doing gauges with dash in is doable with 2Gs but not 1Gs
x2xtreme360
03-03-2011, 02:15 PM
I can see how it's possible. With my dash out of the car, I can easily stick my hand in the passenger airbag cavity but again, huge PITA.
Also, removing the dash allowed me to rewire my alarm system and it just overall made working in that area a hell of a lot easier. Plus, it's about 10 degrees here and I mounted, fabbed, and wired all this up in my bedroom;)
To anyone who is intimidated by removing the dash, it's all just nuts and bolts and there really aren't too many of them. I didn't even have to remove my center console to get the thing out.
Bluz, dash removal is incredibly straight forward and simple to do with only basic tools. If you ever end up having to do it (doing gauges w/o removing the dash is a PITA) then you should have NO issues doing it.
Atrocity, pretty!
Did the center gauges in about 4 hours (new face overlays for main and center) on my 95. Pull the center vents, cut a hole in the right side of the main cluster plastic after the assembly is out (it's covered when reinstalled) and it's pretty easy. Removing hardware was cake. Manipulating the gauges to slide out - not so much. Sort of like removing the rear precat with the motor still in - frustrating - but possible.
Maximal
03-03-2011, 05:18 PM
Did the center gauges in about 4 hours (new face overlays for main and center) on my 95. Pull the center vents, cut a hole in the right side of the main cluster plastic after the assembly is out (it's covered when reinstalled) and it's pretty easy. Removing hardware was cake. Manipulating the gauges to slide out - not so much. Sort of like removing the rear precat with the motor still in - frustrating - but possible.
This is what I did, cut that hole and you have a ton more room. If I worked at it a bit more I probably could have got them out without breaking the stock gauges but I didn't really care so I just yanked to make it easier. I installed mine in an afternoon while taking my time. Pulling a dash is pretty straight forward but somewhat time consuming. And I hate having a million little screws to keep track of. :lol:
mh3kgt
03-03-2011, 07:54 PM
Supposedly doing gauges with dash in is doable with 2Gs but not 1Gs
Not impossible on 1g but deffinately not fun. I've done it a few times on mine now, but the last time I ended up cutting a hole behind the main cluster to get at the center gauges easier.
*Edit* Oh and Atrosity what did you use to dye your dash black? I wanna do my whole dash/center console/seats/door skins black
Chris GTO TT
03-03-2011, 10:35 PM
Not the greatest pic and these are the DSD series instead of the X-Line like Brent has. Like I said they push in from the outside so they don't sit in as far but still have that there from the factory look.
https://lh6.googleusercontent.com/_4tAgKC3U8lM/TW-aQFY6WNI/AAAAAAAAAHs/3WYMr7CDRlc/s640/IMG_20100821_170502.jpg
I can probably grab better pics if you guys needed them.
What is the difference between the Xline and the DSD?
CoopKill
03-03-2011, 11:07 PM
^ x2...
Maximal
03-04-2011, 12:40 PM
Xlines are still digital but their stepper motor isn't as heavy duty. The DSD series also has warning and peak functions.
Nihil
03-04-2011, 12:51 PM
I highly recommend dying the dash black if you have it pulled out! I simply love mine. It always has a glossy armor all shine, doesn't peel or anything.
http://i52.photobucket.com/albums/g19/Atr0sity/2.jpg
Doesn't the gloss finish give you more glare in the windshield?
Here's a pic of mine with Prosport 60mm's
http://img.photobucket.com/albums/v229/prevailingevils/Stealth3000gt/95Stealth/05.jpg
Notice the glare from the color, one thing I've learned is, choose colors wisely, darker and flat or satin will give less glare...of course, polarized glasses/sunglasses will cut right through that problem ;)
mh3kgt
03-04-2011, 01:19 PM
Is that the SEM paint? I plan to paint my dash/interior black with it.
Nihil
03-04-2011, 01:46 PM
Is that the SEM paint? I plan to paint my dash/interior black with it.
If yer askin me, yes it is indeed. It's pretty good stuff, but expensive...I used SEM for the beige color and I went to walmart and bought duplicolor black because it was waaay cheaper and I was only doin vents and such, so they're not high wear areas, though, I DID do the outter steering wheel and shift knob and I'm REALLY surprised at how well it's lasted, honestly, I gotta say, it's tougher than the SEM, my shift knob is still black and my steering wheel hasn't worn off as much as I'd have thought it would, paint and prep was the same for both paints, too.
mh3kgt
03-05-2011, 01:40 AM
What kind of duplicolor did you get? Almost pulled the trigger on a few cans of SEM lastnight...interested to hear what duplicolor you went with
Nihil
03-05-2011, 02:27 AM
What kind of duplicolor did you get? Almost pulled the trigger on a few cans of SEM lastnight...interested to hear what duplicolor you went with
The vinyl and fabric stuff, I used SEMs prep stuff though, here's the email I got from a SEM rep before I had used anything. I emailed a query, I gotta say SEM was quick to reply.
Thank you for your interest in SEM Products. The Products you arelooking for is Color-Coat or Sure-Coat. The Color-Coat is recommendedfor vinyl, plastic, velour and carpet. The Sure-Coat is recommended for leather. For the plastic, clean first with 39362 SEM SOAP and a grayscuff pad then rinse off with water and dry. Clean thoroughly with38353 PLASTIC PREP using a clean, lint free towel and wiping in onedirection. To promote adhesion on TPO, PP, EPDM, and other similarthermoplastics, use 39863 PLASTIC ADHESION PROMOTER. To promote adhesionon ABS, PVC, apply a medium wet coat of 3836() SAND FREE. When 3836()is used, the first application of Color-Coat should be applied on the3836() while the surface is still wet. Please prefer to our web sitehttp://www.sem.ws/tech_sheet/rap-1.pdf for proper applicationprocedures. Please read this carefully before you do anything to yourinterior.
I did the same prep to everything aside from SEM for the beige, and Duplicolor vinyl and fabric for the black. In my opinion, satin finishes and darker colors are going to reflect a lot less on the windshield so you'll have WAY less glare, but, some polarized Oakley sunglasses resolve that problem as well ha.
I'd say, in my opinion, depending on what color you're looking for, I'd go with the duplicolor, SEM has a lot of factory color matches, where duplicolor IS more generic, but in my experience, the dupli has given the SEM a run for it's money, SEM was roughly $15 a can and it took about 10 cans with the light beige I went with, and dupli was about $5 at walmart...
The SEM cans sprayed almost in a mist, which made it REALLY hard to cover such a dark color since I went with such a light color, I've heard you can get the SEM products in commercial qt's and spray with traditional compressor and sprayer, mixing the paint like you'd do with exterior autobody paint applications, I think that would yield better results too, you can mix everything and throw on a good even thin coat with your own flex agent and everything, in short, the SEM in a aerosol was hard to use as opposed to traditional aerosols including the dupli-color
I did mine about 4 years ago, so products may have changed...
MADMarc
03-05-2011, 02:26 PM
Did you only do the dash beige? Holy moly @ 15 cans! That's no joke. How did the vinyl feel after application? I've heard some say much harder and others say the same.
mh3kgt
03-05-2011, 02:54 PM
Interesting. I've used the Duplicolor vinyl/fabric dye on my old DSM to dye the grey cloth seats black, and it did a good job of that. My brother used some to do his dash black on his DSM as well, but I haven't really checked it out that closely. Sounds like Duplicolor is going to be my cheaper and comparably effective solution. Thanks for the input
Nihil
03-05-2011, 03:08 PM
Did you only do the dash beige? Holy moly @ 15 cans! That's no joke. How did the vinyl feel after application? I've heard some say much harder and others say the same.
The vinyl is still the same, if you use the right paint, it should be the same, the vinyl paints have a flex agent added to them so they stay pliable and able to flex rather than chip and crack, causing the rest to flake off.
I bought a box of parts from a local person in town and there was a center consol piece that had been painted black, it was shiney and hard, my guess is they used something for plastic or just regular spray paint, interior paints should have a satin finish to reduce glare and they shouldn't change the feel either.
I only did the dash, shortly after doing the mods I'd done to this car, I picked up a TT so I've layed off on modding it and I'm debating weither or not to pick up a stripped TT and part that interior into it, finishing the color change in the process
Nihil
03-05-2011, 03:11 PM
Interesting. I've used the Duplicolor vinyl/fabric dye on my old DSM to dye the grey cloth seats black, and it did a good job of that. My brother used some to do his dash black on his DSM as well, but I haven't really checked it out that closely. Sounds like Duplicolor is going to be my cheaper and comparably effective solution. Thanks for the input
Definitely, if you're gonna go with black, I'd do Dupli-color, it's way cheaper and holds up excellent from my experience....I don't know well it works with using on carpet though...
Funny story, my dad I swear is senile sometimes, he used some left over dupli I had, on his moto gear, to change it black......that didn't turn out so well lol after seein that experiment gone wrong, I never again thought about using it to dye carpet. I used RIT dye and hot water in a spray bottle, it faded quickly though, and rubbed off for the longest time
x2xtreme360
03-05-2011, 03:13 PM
Just got the dash in the car. The gauges illuminated with the ignition key on but shut off when I turned the lights on. Took the dash out (wasn't bolted in at this point so it wasn't difficult) and took it inside for testing. Used a car battery, everything worked fine. Took it back out, didn't work with lights on. hmmm, swapped in the redtop battery because the one in the VR4 is just a bad battery for unlocking the doors (shaved door locks). The gauges dimmed the way they should with the lights on. Took awhile to figure out the issue but got the dash back in and everything seems to be working well. Now I just need to hook up all the senders and I'm golden.
Nater3kgtVR4
01-29-2014, 07:01 PM
im doing this right now with the x line v2 52mm guages. i have a complete charcoal interior and exterior is going to be flat white. i have to find a flat charcoal to match my carpet, do flat black and see how close it is.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.