View Full Version : Taking off the timing belt, step by step?
Danube_3KGT
02-16-2011, 02:18 PM
Im kind of looking for someone who can tell me what all needs to come off, and where/how it does in order to get to the timing belt.. I need to know ho to get all the serpentine belts off and stuff so I can get everything but the crank shaft off and ready for when my friend gets here tomorrow with the impact wrench..
DocWalt
02-16-2011, 02:33 PM
John's Repair Center (http://www.vr4stealth.com/60k-tune.htm)
Ignore the steps that are about removing the radiator, you can pull the timing belt without removing the radiator. Do the steps up to where you start taking off the water pump and stop, that doesn't need to come off unless you're doing the 60K. While you're at it, I'd spin everything (except for the cams and crank) to make sure they spin smoothly and don't bind. When you're done doing your maintenance (I assume not a 60K, idk) jump to step 26 and install the belt.
Oh, and you don't need an impact wrench for any of it. You can either put it in gear (manual tranny, TQ convertor would just slip) and have someone hold the brakes and you push really hard, or (and IMO, not quite as safe if you're not careful) brace a breaker bar on the subframe and bump the starter to break the crank bolt loose (make sure you're doing it in the right direction!).
AdamVR4
02-16-2011, 02:35 PM
What happened to team3S?
DocWalt
02-16-2011, 02:40 PM
What happened to team3S?
I'm pretty sure it went down a while ago, or I would have linked him there as well.
Alan92RTTT
02-16-2011, 02:46 PM
The person that owned the team3s domain passed away. The group is working through the process of getting the name back and getting hosing worked out. The mailing list still works.
Danube_3KGT
02-16-2011, 03:50 PM
yea, people kept telling me to check team3S's guide, but the sites been down.. Thanks for the help.. Its been 2 months since I got to drive my car and Im hurting to get this fixed.. my fiance is pregnant and is due in less then a month and I hate the idea of taking her car to work and her being home alone without a car in case something happens.. I need to make sure I didnt bend any valves as well though.. Im starting to go crazy..
gltasn
02-16-2011, 10:20 PM
just keep reading it over and over and it will all start to make sense. just dont jack it up by the pan!
Danube_3KGT
02-17-2011, 03:38 AM
We did jack the engine up by the oil pan, how ever we put a board between the jack and the pan to help disperse the weight.. seems how ever I have bigger problems.. I turned the crank shaft tonight and have piston smack? i think its called.. so pretty much, I know I have a valve bent, probably more.. So some how, with a kid due on the 9th I have to figure out how Im going to get this all fixed before I get so pissed I just sell it..
akotten
02-17-2011, 09:33 AM
We did jack the engine up by the oil pan, how ever we put a board between the jack and the pan to help disperse the weight.. seems how ever I have bigger problems.. I turned the crank shaft tonight and have piston smack? i think its called.. so pretty much, I know I have a valve bent, probably more.. So some how, with a kid due on the 9th I have to figure out how Im going to get this all fixed before I get so pissed I just sell it..
That and you probably just dented your oil pan. NEVER jack up the car using the oil pan. There is no reason to ever consider it.
Beamed from my Droid X
AdamVR4
02-17-2011, 10:41 AM
That and you probably just dented your oil pan. NEVER jack up the car using the oil pan. There is no reason to ever consider it.
Way to kick him when he's down. A board alone may be sufficient, but I've always used a board and towels and never dented a pan.
You could have at least mentioned that the alternative is to use the AC compressor bracket.
gltasn
02-17-2011, 11:07 AM
danube its easy to jump the gun and say the car is fuct but it reall only takes me a few hours(5-8, im old and take my time) to change a timing belt. please find a local member to look at your car and see whats up. do a compression check if the tb is still on the car and you will know if you bent a valve. if you heard a clack from releasing the tb and the cams let lose you could still be ok.
if you jack up by the pan i use a brand new roll of ducttape on my jack with a folded towel over the tape. i center the dome on the pan(pick up area) in the center of the ducttape roll. never dented a pan with my method but i cant rec. it to others. copy if you want but never say i said it was ok to jack up by the pan. j
akotten
02-17-2011, 12:26 PM
Way to kick him when he's down. A board alone may be sufficient, but I've always used a board and towels and never dented a pan.
You could have at least mentioned that the alternative is to use the AC compressor bracket.
Whoa, I didn't mean to come across as an asshole. My apologies. I'm running on 1hr of sleep today so I didn't really feel like offering alternatives. I've had these motors on an engine stand before and I know how much they weigh, let alone the entire car. Our oil pans are pretty thin IMO, maybe even too thin. It just doesn't make sense to me to risk denting the pan considering the already small tolerance between the pickup tube and bottom of the pan. Can it be done using a board? Perhaps, but its a risk I am not personally willing to take.
Danube_3KGT
02-18-2011, 03:34 PM
Well, it still doesnt run, but I did get some goodies in today.. oooooh Shiny!
http://i670.photobucket.com/albums/vv64/Lordofwar918/underhood.jpg
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.