View Full Version : Show me your modified 1st gen bumper
vr3.9
09-13-2010, 11:45 AM
Time for me to open up a little air for the FMIC and radiator. The faster I go the hotter it runs. I might go 99 someday, but for now I'm just going to modify the crash bar and cut some breathing room in the bumper cover. So show me what you've got or what you've seen.
enigma
09-13-2010, 12:06 PM
here's one I modified 3 years ago, enlarged the mouth, filled the moustache and done away with the oe fog lamps.
http://img.photobucket.com/albums/v461/parsonsnose/gtofront0.jpg
ballermj23
09-13-2010, 12:11 PM
here's one I modified 3 years ago, enlarged the mouth, filled the moustache and done away with the oe fog lamps.
http://img.photobucket.com/albums/v461/parsonsnose/gtofront0.jpg
that front looks sick!!
Atrosity
09-13-2010, 12:18 PM
Wow that looks clean enigma!!
vr3.9
09-13-2010, 12:19 PM
Yea i normally don't like them when they cut them out like that. But the way you finished it out makes it look awesome. I was going for something simple but hey, I like it. What did you use for material when you modified it? Any how to's appreciated.
ballermj23
09-13-2010, 12:23 PM
heres another one http://vidxc.com/i/roy/d15aab26861vr4_2.jpg
Atrosity
09-13-2010, 12:32 PM
heres another one http://vidxc.com/i/roy/d15aab26861vr4_2.jpg
Hey baller!
I was actually thinking about doing this to my car as my car is a 1G now. But it looks kind of out of place, what do you think?
x2percentmilk
09-13-2010, 12:35 PM
holy crap enigma that is beautiful
ballermj23
09-13-2010, 12:42 PM
Hey baller!
I was actually thinking about doing this to my car as my car is a 1G now. But it looks kind of out of place, what do you think?
Hey eric
welll the silver was done better.! look at the Foglight, cut design and fiberglass work.
ballermj23
09-13-2010, 12:43 PM
the silver bumper looks OEM the the second pic doesn't. :P
enigma
09-13-2010, 12:48 PM
Thank's for the kind comments, the mods were done with the bumper removed, once removed the bumper ends tend to widen, if you intend to fill in the moustache you must jig the bumper width to the exact measurement as when fitted to the car, I used a long wooden batten screwed to the bumper ends to hold it in position.
I cut out the area between the fog lamps and used 4 inch plastic pipe to create the driving lamp apertures, the central area was cut up to the lower moustace line and wide to enough to accomodate the fmic, effectively to what ever size fmic you have fitted
On the maustache area I scuffed and drilled a series of holes over the area above and below the moustache line for the bodyfiller to adere to, also filling/overlapping above and below the moustace area.
The central mouth was created using metal and fibreglass and resin to bond it to the bumper, the finer details were done with body filler.
Tony
http://img.photobucket.com/albums/v461/parsonsnose/bumpspot6.jpg
http://img.photobucket.com/albums/v461/parsonsnose/bumpspot1.jpg
ballermj23
09-13-2010, 12:54 PM
nice! i see you got second gen side skirts.
fastnelson
09-13-2010, 12:57 PM
this is what i did, still testing ...
http://i165.photobucket.com/albums/u63/fastnelson/pics%20for%20the%20web%20site/logo-1.jpg
Polygon
09-13-2010, 01:22 PM
Not mine, but far and away my favorite. Haven't seen him post is a long time but it's Jessie Rink's car.
http://www.synapsepc.com/Hosting/CarDomain/Stealth/Ideas/Jesse%20Rink%27s%20%2792%20RT%20TT%20%28Front%20En d%29.jpg
vr3.9
09-13-2010, 01:29 PM
http://img.photobucket.com/albums/v461/parsonsnose/bumpspot1.jpg
I really do like that, look like no compromise in either form or function.
Atrosity
09-13-2010, 01:33 PM
Not mine, but far and away my favorite. Haven't seen him post is a long time but it's Jessie Rink's car.
http://www.synapsepc.com/Hosting/CarDomain/Stealth/Ideas/Jesse%20Rink%27s%20%2792%20RT%20TT%20%28Front%20En d%29.jpg
This has to be my favorite 1G Stealth ever.
Polygon
09-13-2010, 01:46 PM
Mine too. I fell in love with his car when I saw it in the 3S calendar. I so want that bumper. Too bad it's completely custom.
toddrs93
09-13-2010, 02:03 PM
Heres just some simple quick cutting of the stock bumper
http://i173.photobucket.com/albums/w51/toddrs93/redvr42.jpg
http://i173.photobucket.com/albums/w51/toddrs93/l_d65d2d3ab2c44aab9a5ba8e81beb6f66.jpg
Not mine, but far and away my favorite. Haven't seen him post is a long time but it's Jessie Rink's car.
http://www.synapsepc.com/Hosting/CarDomain/Stealth/Ideas/Jesse%20Rink%27s%20%2792%20RT%20TT%20%28Front%20En d%29.jpg
Anybody have any info on how he did this? Im going to try this on my bumper since its just laying around anyway. Id rather have this setup then a 99...
Polygon
09-13-2010, 02:14 PM
Anybody have any info on how he did this? Im going to try this on my bumper since its just laying around anyway. Id rather have this setup then a 99...
We discussed this on the other site and I think we came to the conclusion that he shaved the mustache. Then we think that he cut the 1st gen center section out and put a 99 center section in.
Shit that sounds like to much work...
Monster Stealth
09-13-2010, 03:34 PM
http://lh5.ggpht.com/_tLwzPTS_Xjo/TIUyIds-FCI/AAAAAAAAMcE/WikqAajJ-Po/s800/IMAG0101.jpg
http://lh5.ggpht.com/_tLwzPTS_Xjo/SSzfH7qJCPI/AAAAAAAAGH0/uW1UPUF85dk/s720/P1010318.JPG
20G_VR4
09-13-2010, 04:25 PM
http://i109.photobucket.com/albums/n64/redline3kgt/P1000530.jpg
mines the green one. sorry its so hard to see, its the best pic i have
green-lantern
09-13-2010, 04:42 PM
Justin needs to post a pic of Mr. Giggles
vr3.9
09-14-2010, 01:36 AM
ok this is what I did for now. Latter i will either put an inside wall around to match the bottom or maybe grill it or go 99. Anyway, it works for now. Took it out this evening and instead of 204 -210 ran at 189. So at lest it works.
http://i225.photobucket.com/albums/dd64/reachmercer/newfront.jpg
Polygon
09-14-2010, 01:52 AM
Shit that sounds like to much work...
I would agree. However, I'd gladly pay for someone to make me one.
Default
09-14-2010, 02:18 AM
Mine is the first i've ever seen of it.... A modified stealth ES front
http://i57.photobucket.com/albums/g238/cztoad/IMG_0165.jpg
http://www.z-hub.net/Carnew_01.jpg
My92Stealth
09-14-2010, 02:43 AM
Did this in the parking lot of NG09
http://img.photobucket.com/albums/v325/Mr.Wolf/TT/IMG_3212.jpg
Hard AttacK
09-14-2010, 11:18 AM
That looks awesome vr3.9! How did you do it?
Atrosity
09-14-2010, 12:24 PM
That looks awesome vr3.9! How did you do it?
I agree, it looks like on of the more cleaner 1G Bumpers that could've came stock like that!
vr3.9
09-14-2010, 12:34 PM
I first tried just an opening where the crash bar was kinda like Bill Buels but a little smaller. Thought some kind of grill set in behind it would work. Cut it 25" but the only expanded metal I could find was 24"s. I went to a local salvage yard to see if there was some other grill front I could modify to fit in the whole to. a. Hide all the junk and cut edges. b. give more of a factory look. Found several that might have worked but opted for simplicity at this time. Decided to just cut it all out trying to reverse match the angle of the bottom part. I will probably take it off later and fiberglass in a lip going around it to make it look factory. Still like the idea of some kind of mesh covering. Cleaner plus really don't like the inter cooler taking the brunt of an debris.
used drill to make the corner starting wholes. Grinder with cut off wheel. Hack saw blade and jig saw.
Jig saw turned out to work best.
enigma
09-18-2010, 09:09 AM
This is what I have fitted now, Kaze bumper with custom ABS plastic undertray modified for mk2 turn signal lamps led side lights and 6000k xenon driving lamps.
http://img.photobucket.com/albums/v461/parsonsnose/P1010061-1.jpg
dfoster101
09-18-2010, 11:56 PM
love this bumper,, outragious and still clean without the rice factor
This is what I have fitted now, Kaze bumper with custom ABS plastic undertray modified for mk2 turn signal lamps led side lights and 6000k xenon driving lamps.
http://img.photobucket.com/albums/v461/parsonsnose/P1010061-1.jpg
11secondFWD
10-05-2010, 11:14 PM
Here is a new pic of my dsm. I cut the front bumper for better airflow to the intercooler and radiator and tranny cooler. I had my doubts and I thought cutting the bumper always looks like crap but I am very pleased with the outcome. I cut it with a razor blade/box cutter and put the trim around the inside of the hatch on the bumper.
http://i123.photobucket.com/albums/o293/94atxvr2/356010127877_0_0.jpg
The bumper cutting is pretty symmetrical to the bumper but I mounted the FMIC a little off centered. And the part of the fmic core that is now exposed is greasy and neewds to by hosed down. But Overall I think form and function improved.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.