View Full Version : Radio Install Help PLEASE
Rom3BreaK
02-02-2011, 10:38 PM
Hey, so I've been working half a day on just figuring out the pins/wiring of my alpine head unit (the stock wiring harness to be exact). I know it should not be this difficult, and I feel as though I've found mixed/inaccurate information in a few different places, causing way too much headache.
The wiring diagram in the manual is a little confusing to me, and is not straight forward enough. I've been looking on 3/s audio faq and have been looking at a pin diagram corresponding with each pins wires, and this is either inaccurate, or I'm missing a wire (at least) in my harness.
Main area of confusion is pin A as referenced by 3/s audio faq. The faq calls for 2 white w/red stripe wires. In that place I instead have a white/blue wire (only one, not even two).
Anyways, without getting in to this too much, could anybody please break this down for me? I've basically been looking at 3/4 different sources and they all seem to say something just slightly different...and it seems like I don't even have wiring for the right front speaker (positive or negative).
I'm fine with the harness that has two pins on the top row, one on either side of the clip, and three pins on the bottom row. It's the harness with 4 pins along the top and 5 along the bottom that's really throwing me off.
After I get that straight, the radio install should be cake.
Thank you,
Caleb
Rom3BreaK
02-02-2011, 11:56 PM
Green/White Black/Yellow XclipX Yellow/Red White/Blue
Blue Red/Black Yellow/Blue (2) White/Blue Not used
(2) Black/Blue XclipX Gray/Blue or White/Blue
Black/Blue Pink Gray/Red
That's what I'm working with; ms paint and excel files were aparently too big so sorry about the format...
Rom3BreaK
02-03-2011, 08:54 PM
Bump....
stealthee
02-03-2011, 09:06 PM
This is why you don't cut and splice into the stock harness. Quick connects are cheap and, uh, quick. ;)
mh3kgt
02-03-2011, 09:12 PM
I have a reverse radio harness I'll sell you for like $10shipped if you want. It is color matched to the stock harness and connects to the factory radio wires if they have been clipped and has the factory connectors on the other end. All you would need then is a harness to fit your headunit and then clip the connectors together and voila all wiring is done for you! Here's a link to the radio harness you'd need once you have stock connectors back in place http://www.amazon.com/Stereo-Harness-Mitsubishi-3000GT-installation/dp/B000KL51X0 :p
Rom3BreaK
02-03-2011, 09:25 PM
Yeah, this whole things is pretty weird... I think the previous owner had some crazy system in the car. I can't see where any wires have been cut (if any have been cut, they did a clean job wrapping everything up). Funny thing is, there is a quick connect harness connected right now that was hooked up to an older sony unit that I just removed. The wires on the quick connect don't seem to be the "typical" colors, making everything more confusing. Basically I have all the wires I need (I think), I just need to figure out what each does.
Now that you mention it, I have an entire wire harness out of a 91TT in the basement....thanks for the inadvertent reminder!
I'm also confused as to how you wire this thing so the antenna goes up/down when radio is on/off.
mh3kgt
02-03-2011, 10:10 PM
Needs the power antenna input from the aftermarket radio harness to stock connector. Usually blue/white on most aftermarket harnesses.
Rom3BreaK
02-04-2011, 12:23 AM
Nice, got it. For some reason whoever installed the old unit had looped the power antenna in with the ignition switch, which explained why the antenna went up and down every time the car was turned on and off rather than when the radio was turned on and off. I think I have all of the wiring figured out now also, but it's still odd that I don't have two wires for the right front speakers(only one each for (+/-))...probably means that dash speaker won't work. Maybe I'll undo the electrical tape holding the harness together and try to locate cut wires.
Why would anybody even cut those wtf?
stealthee
02-04-2011, 07:01 AM
If you are missing right front front then both the dash and the door speaker wont work as they are on the same circuit of wires.
blackrob
02-05-2011, 11:49 AM
I can tell you that one of the morons cut the dash speaker wires in my car 2 inches from the connector. Why the hell would you do that?
Caswell239
02-05-2011, 01:07 PM
i had the same thing, a previous owner had cut the stock plugs off and just wired it in. so i just bought a chunk of the stock harness with the plugs and soldered it back in. took a few mins but way easier in the end
stealthee
02-05-2011, 01:09 PM
Some people think they know how to install stereos when all they know is hack jobs.
When I installed aftermarket speakers in the stock locations I made adapters to plug into the stock wiring even though I don't plan on putting stock speakers back in there place ever. It took all of 5 extra minutes to do too. If people took that 5 extra minutes it would make life on future owners 100 times easier.
reallyxxxxxxloud
02-06-2011, 04:23 AM
MMM not necessarily. Well yes if its a near stock stereo. And seriously if you don't know how to find what each wire does without a plug, you shouldn't be even touching it. Just as much as you are saying its a hack job if the plug isn't there, I see way more home attempts that are poorly soldered/crimped/mounted etc
Lithium
02-24-2011, 04:51 PM
MMM not necessarily. Well yes if its a near stock stereo. And seriously if you don't know how to find what each wire does without a plug, you shouldn't be even touching it. Just as much as you are saying its a hack job if the plug isn't there, I see way more home attempts that are poorly soldered/crimped/mounted etc
I was a roadshop manager for 2 years and this explains everything, get yourself a multimeter.
J_Parker
02-28-2011, 10:59 PM
I was a roadshop manager for 2 years and this explains everything, get yourself a multimeter.
^^^This. If your stock harness has be cut all you need to do is find you power, acc, and ground. From there on finding which speaker goes where is easy.
As for install techniques, I am a big fan of bullet connectors. I frequently remove and change headunits/speakers so they just make my life all that much easier :p
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.