View Full Version : Removing the rear precat from above on a 2nd gen?
Modern 3kGT
01-11-2011, 07:27 PM
I have a 97 vr4 and am looking to change the plugs and wires out next weekend. I was wondering if while I have the plenum off and what not would I be able to also get to the rear precat and remove it from above? Or can it only be done from below?
If I can do it now that would be awesome as I am not totally confident with my mechanical skills yet to remove the cv axel to get to the rear precat...
Thanks, John
dbest671
01-11-2011, 08:45 PM
I know somebody once said it can be done without doing anything special, but I think that person was just an exception.
First you will have fun getting that damn heat shield off, it is a b*tch. I got my out from the top on the 94. I tried for like two hours and it kept hitting the hard lines on the firewall. So since I was changing out the oil pan anyways, I decided to jack up my engine. I undid the driver's side mount and jacked the engine up until I could pull the rear cat out, probably about 3/4" to 1". Then I had to put it back on, when I sold the car, I VERY VERY carefully jack up the engine again, by the oil pan but not on the bowl part, and put it back on. Other than jacking up the engine, I don't see how the rear cat would come out from the top.
DocWalt
01-11-2011, 09:03 PM
You need to jack the engine up, or at least I did.
Modern 3kGT
01-12-2011, 12:32 AM
Man I was hoping I this would be easier!! Oh well, thanks for the responses guys.
John
Modern 3kGT
02-15-2011, 08:12 PM
I just purchased solid motor mounts from maximal so I plan to install both the new motor mounts and the rear precat at the same time. What added protection did you use to not dent the oil pan? How much can the engine be lifted before you damage anything else? Which of the stock mounts should be removed first in order to allow the engine to be jacked up the easiest?
Thanks, John
dbest671
02-15-2011, 08:17 PM
I only undid the driver's side. Only had to jack it up about an inch if that. The first time I didn't care about denting the oil pan because I was replacing it and the strainer. But I used a thick ass phone book as to not do to much damage. It didn't dent the oil pan at all. When I had to put the rear precat back on, I used a little 2x2 of wood on the edge of the pan, not the center where the bowl is. It worked like a charm.
What I did was slowly jack the engine up and try to get the cat out, I knew that I couldn't jack to much without undoing some more motor mounts.
Modern 3kGT
02-15-2011, 09:01 PM
Well it sounds like this will be advantageous to change the mounts at the same time then... if you were going to undo another mount to allow for more clearance which engine mount would you unbolt?
Thanks, John
dbest671
02-15-2011, 09:07 PM
Well considering the rear mount is a b*tch, any of the other ones would be sufficient. But I was able to do it with just undoing the driver's side mount.
Modern 3kGT
02-15-2011, 09:12 PM
Am I missing something here? ....This seems so much easier than trying to pull it from below. I'm not misunderstanding anything right??? haha
DocWalt
02-15-2011, 09:16 PM
I just pushed up on the edge of the block/pan with a 2x2 when I jacked it up, but I may have had the driver's side mount off, don't remember.
Modern 3kGT
02-15-2011, 09:35 PM
Very cool guys... I'll let you know how it turns out. I think this is a great alternative to pulling the half shaft and cv axel...
Thanks, John
dbest671
02-15-2011, 09:35 PM
I wouldn't have taken out the rear precat if I had to remove all the crap you have to to pull it out from below. I think it maybe took 20 minutes to get the rear precat out from the top. Just undo driver's side motor mount, jack engine, pull out cat, slowly drop engine enough to reattach the mount, and done.
VR-4 0wnz j00
02-15-2011, 11:53 PM
It is possible. I was under the car while my friend was pulling from the top. You need to jack up the engine by the oil pan to raise it enough to clear the intake. It took hours and pulling and fussing to figure it out.
Chris GTO TT
02-16-2011, 10:07 PM
Is there really something that makes this so different on a 2nd gen? I got mine out the top fairly easily. One person on the top one on the ground and you can get it out.
dbest671
02-16-2011, 10:12 PM
Is there really something that makes this so different on a 2nd gen? I got mine out the top fairly easily. One person on the top one on the ground and you can get it out.
Yes actually there is, the flange on the bottom is different and something else. I know I tried for at least two hours to get that thing out without jacking the engine up. There is NO WAY IN HELL that thing is coming out from the top without jacking up the engine. Unless you have half the engine taken apart, with turbo and exhaust manifold off.
Chris GTO TT
02-16-2011, 10:19 PM
Ok well then continue with the thread :)
Modern 3kGT
02-17-2011, 12:43 AM
I'll post pics and details afterwards... looking like it will be not this weekend but the next. The girlfriend has plans for my birthday this weekend.
John
Once you get the rear precat replaced, just do the motor mounts one at a time. Rear first, then front. That way, if you need to take a break, you can do the sides later. They're also the easiest.
DocWalt
02-17-2011, 01:23 AM
Actually, I had it out without jacking the engine afterwards, but I DID pry the engine forward with a 4' long iron pipe against the subframe and against something solid on the engine (don't remember, sorry). My mounts were 150k factory mounts, so not in perfect shape, lol.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.