PDA

View Full Version : Timing belt 101



Tackhammer
01-11-2011, 08:55 AM
12345

Tackhammer
01-11-2011, 08:56 AM
Does the video show up for anyone? I dont see it, but its there if i go to edit it.

Must be a Firefox setting, can anyone tell me what i need to change?

Fakepower
01-11-2011, 12:46 PM
I see it fine. Thank you.

green-lantern
01-11-2011, 01:17 PM
Yeah I see it.

mb3000
01-11-2011, 06:49 PM
Same here.

rawavr4
01-11-2011, 09:18 PM
This is what I've been looking for for months. I need to do this and the oil pump.

J. Fast
01-11-2011, 11:52 PM
Excellent contribution Hammer. I think I'll try you're method the next time I have the engine out. Why are cam lockers the devil?

wingnut
01-12-2011, 03:22 AM
Why are cam lockers the devil?

been doing it same way since my DSM days...70 bucks vs. free :D

akotten
01-12-2011, 05:15 AM
Funny how easy it is when the motor is out of the car. Nice video.

Tackhammer
01-12-2011, 10:17 AM
Why are cam lockers the devil?Because at about the 4:15 mark in the video when i take up the initial slack, that causes the lockers to bind up and they are really heard to pull out, so i think most just leave them in and allow the crank to rotate and not the cams, during the final tension setting, which is not supposed to happen

mh3kgt
01-12-2011, 12:01 PM
Thanks for the video. Been using pretty much your same method, but I don't use the tensioner tool (don't have one) I just unbolt the hydraulic tensioner and set it to where I can put the pin in and out freely. Probably not the best method, but it's worked for me thus far.

zelstin
01-12-2011, 08:56 PM
Lets make a deal. You change my timing belt and I will use my fine tuned knowledge of direct current to eliminate that annoying beep coming from your smoke detector :p Thanks for the video!

Tackhammer
01-14-2011, 08:03 AM
Im in a different shop now lol

green-lantern
01-14-2011, 08:16 AM
Im in a different shop now lol

I was getting ready to so say damn Wayne you still haven't put a battery in that thing?!?! Lol All your videos seem to have that annoying beep.

Tackhammer
01-14-2011, 11:24 AM
i never did change the battery. I dont even hear it in the videos i was so used to hearing it on a daily basis

FluffyCow
01-14-2011, 11:34 AM
Is it bad to be afraid to do my 120k on my own? Gotta watch the vid when I get home(doesn't show up on safari mobile on my iPhone)

mh3kgt
01-14-2011, 11:58 AM
Maybe I missed it, but how are you keeping the cams in time? Looks like you moved them around quite a bit installing the bolt cam lockers, or did you line up the timing marks as you tightened the bolts?

Tackhammer
01-14-2011, 01:49 PM
line up the timing marks as you tightened the bolts?This, and then you usually have to move them a little bit to line up the belt cogs.

Memphetic
01-14-2011, 02:46 PM
Funny how easy it is when the motor is out of the car. Nice video.

More like how easy EVERYTHING is with the engine out of the car... space is definitely the enemy with these things :p

mh3kgt
02-23-2011, 05:13 PM
Quick question: Is it okay to do timing like I have been doing without the tensioner tool? I use a vise to press the hydraulic pin back in and put an allen key in the hole to keep it in place, then I bolt it to the motor, but have to pry the tensioner pulley bracket up in order to slide the hydraulic tensioner in. This is while the belt is already installed. The pin/allen key is still able to be pulled in and out freely. Question is, is this method allowing the proper tension on the belt? I have done it this way a few times and after rotating the engine the timing marks always line up, and I have never had a belt slip or anything. Is this a viable option for those who don't have a tensioner tool?

J_Parker
02-23-2011, 10:31 PM
I don't see anything wrong with doing it like that, other than potentially over tightening which can cause the belt to wear premature. What I did for a makeshift tool was use an old socket, welded some small doweling onto it using my old tensioner pulley as a jig, and threw it into some cold water while it was still hot to temper it. I have used it many times and continue to do so!

mh3kgt
02-23-2011, 11:07 PM
I've heard of some people using those hooks that go in peg boards as a makeshift tensioner tool...we've got a bunch of those at work maybe I'll give one of those a shot.