PDA

View Full Version : 3/S color change. who knows paints?



Greg E
12-13-2010, 11:23 AM
You guys might remember my SSG Stealth?
http://www.3si.org/forum/f60/pics-my-paint-job-so-far-272813/

Well, I'm doing it again. This time with my 99 VR4. Picked this car up a little over a month ago. 120K southern car. Typical high mileage 3/S. Abused, neglected, wrecked, all kinds of quirks... The car is exactly what I was looking for and it was cheap!

The car will be completely disassembled, engine pulled, sub-frames dropped, interior stripped, paint stripped (soda blasting all the metal parts) then everything will get redone.

Trying to decide what I want to paint the car with. My first choice is a single stage acrylic urethane paint offered thru Eastwood out here in PA. It's the cheapest in terms of cost/gallon, from what I understand, it's a lot more forgiving for first time painters like myself and it's a lot softer compared to your typical enamel used on cars (so it's easier to touchup and fix runs). It's also a single stage paint that comes premixed. All I add is the activator and spray. Even though it isn't required, I'm still going to clear over it. From what I understand urethane is a lot more forgiving to cooler temps (my garage is heated with kerosene so it's not 80+ degrees in there all the time).

Haven't decided which color I like more if I decided to do the urethane paint, but here are my choices.

http://www.eastwood.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/p39087.jpg
http://www.eastwood.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/p32660.jpg

It's about $110/gal for either of these colors. Figured I'd need about 1.5 gallons to do the whole car, inside and out.

The waterbourne metallics and pearls are a bit more cost wise and they're a lot more fussy to spray/touch-up, but they are absolutely gorgeous!

http://www.eastwood.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/p/2/p25275_1.jpg
http://www.eastwood.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/p/1/p19708_1.jpg
http://www.eastwood.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/p/1/p19788.jpg

These cost around $220/gal plus I need to get a special primer for these which run about $50/gal. Again, they come with everything, but you need to mix them. It's a 3 in 1 system so it gets tricky.

I had considered painting the car using the Mitsubishi Electric Blue Pearl from my EVO, but I can't justify spending $800+ in paint/primer/clear. DuPont makes a "knock off" color which is supposed to be very similar, there again, its still pricey nor do I know what I'm gonna get.

Thoughts?

Emilie@GZP
12-13-2010, 11:27 AM
you can't clear over a single stage. You'll get some funky fish-eye looking shit going on. Get a base-clear, middle of the road brand paint, from any local paint store. You'll hate yourself if you do a single stage, and it always looks like shit in the long run.

If you're doing a base clear complete repaint, you don't need to get the $800/gallon paint. Those paints are best used for color matching, when you need the mix to be EXACTLY right to ensure the best match possible. The lower end paints (Nason...???) are perfect for overall repaints... since you're not trying to match what is already there. Spend your money on a good clear coat, as that is what will take the abuse.

Hans can give you much better advice than I can as far as what brands are best, etc, since he deals more with the paint selections than I do... I just place the orders :)

Greg E
12-13-2010, 11:31 AM
you can't clear over a single stage. You'll get some funky fish-eye looking shit going on. Get a base-clear, middle of the road brand paint, from any local paint store. You'll hate yourself if you do a single stage, and it always looks like shit in the long run.

The tech guys at Eastwood suggested I clear it just to give it a glossier finish. In the sample pic its been cleared. They have their own forumlated 2-part clear which they highly recommend I use to avoid bubbling.

Maybe I should buy pints of each paints and do samples. I have all kinds of spare parts...

Emilie@GZP
12-13-2010, 11:34 AM
as far as temperature to paint... in colder weather, you want a fast activator. single stage does not take well to cold weather.

Emilie@GZP
12-13-2010, 11:35 AM
The tech guys at Eastwood suggested I clear it just to give it a glossier finish. In the sample pic its been cleared.

Maybe I should buy pints of each paints and do samples. I have all kinds of spare parts...

I'd recommend absolutely priming, painting, and clearing a bunch of panels, all different curves, etc before diving into the car. And get a good gun too. None of that cheap crap... play with the settings, etc.

Greg E
12-13-2010, 11:42 AM
as far as temperature to paint... in colder weather, you want a fast activator. single stage does not take well to cold weather.

They suggested I heat the garage to at least 60ish and let it sit that way for 8 hours. Then immediately after spraying, crank the heat with the torpedo heater to 90+ and let it sit that way for at least an hour.

I got a very high quality gun. Not one of those $50 ones from harbor freight.

Hans@GZP
12-13-2010, 11:48 AM
If you want to talk paint, just give me a ring. I absolutely despise single stage paints. They never come out nice and almost always fish eye. No need to go nuts on the color... like Emilie said. You can get nice colors through Nason brand (they use Dupont materials) especially if you are getting something that's just a base coat/clear coat type of deal.

You will want to take some time and practice. I tried just priming some stuff at the shop.... and I'm not that good at it, so I leave it to my body guy LOL

Hans@GZP
12-13-2010, 11:50 AM
They suggested I heat the garage to at least 60ish and let it sit that way for 8 hours. Then immediately after spraying, crank the heat with the torpedo heater to 90+ and let it sit that way for at least an hour.

I got a very high quality gun. Not one of those $50 ones from harbor freight.

Yea, definitely get the metal of the car nice and warm before painting. I put my torpedo heater on the car for an hour or so to get the car's "core" temp up so the paint adheres better. We have some IR heating lights that we use as well.

Depending on what clear you go with, you'll need to keep the garage a minimum of 50 degrees for almost a full day to get the clear to properly catalyze.

Hans@GZP
12-13-2010, 11:51 AM
Oh, and for a first timer... I'd almost stay away from any paints with a heavy metallic flake in it. It will honestly look like a 5 year old painted it with a roller brush.

Greg E
12-13-2010, 11:54 AM
Oh, and for a first timer... I'd almost stay away from any paints with a heavy metallic flake in it. It will honestly look like a 5 year old painted it with a roller brush.

For that they suggested a larger spray nozzle and using a bit of thinner to make the paint more "liquid".

Greg E
12-13-2010, 11:57 AM
If you want to talk paint, just give me a ring. I absolutely despise single stage paints. They never come out nice and almost always fish eye. No need to go nuts on the color... like Emilie said. You can get nice colors through Nason brand (they use Dupont materials) especially if you are getting something that's just a base coat/clear coat type of deal.

You will want to take some time and practice. I tried just priming some stuff at the shop.... and I'm not that good at it, so I leave it to my body guy LOL

I do spray paints here at work so I'm fairly confident in taking on this project. I'll definately check out Nason paints though!

Emilie@GZP
12-13-2010, 11:57 AM
For that they suggested a larger spray nozzle and using a bit of thinner to make the paint more "liquid".

even professional painters have a hard time with metallics, especially in colder weather. Since you're using a faster activator, the paint dries faster... not allowing the metallic flake to settle evenly... and it looks splotchy. Even with a larger spray nozzle, it is VERY difficult to get a heavy metallic paint to lay evenly, especially in colder weather. Warmer/hot weather, you use a slower activator, which allows the paint to dry more evenly on the car, and the flake settles better.

Hans@GZP
12-13-2010, 11:57 AM
I'm not sure how single stage metallics lay out, but for base/clear metallics you want to go with as slow as a reducer as humanly possible without having it go so slow that all the dirt ends up sticking to it. The main problem is that if it dries too quickly the metallic flakes can "stand up" on their sides and it will make the paint look really "dry" and you can see your spray lines. It will look as though you painted over 120 grit sand paper.

Emilie@GZP
12-13-2010, 11:59 AM
I do spray paints here at work so I'm fairly confident in taking on this project. I'll definately check out Nason paints though!

I've spray painted complete cars, spraying from a gun is completely different.

Greg E
12-13-2010, 12:07 PM
I've spray painted complete cars, spraying from a gun is completely different.

Sorry, I meant that I spray using guns not rattle cans. :lol: Yes they are completely different! You gotta take "closer" spray lines with aerosol paints.

Hans, what you're saying about metallics is exactly what the tech guy explained. He also explained they sell different reducers that cure at different speeds. One is a much faster but like you said, the finish won't look as good. Maybe I should wait till spring to spray the car...

Greg E
12-13-2010, 12:12 PM
Do you guys have a bunch of fuel doors sitting around? They'd make great sample pannels.

Emilie@GZP
12-13-2010, 12:13 PM
Spring is definitely best to paint, in all honesty, once the weather starts warming up. Winter is a total pain in the ass, and the paint jobs aren't quite as good if you're not controlling the temperature throughout the whole process. There also won't be the nasty winter weather beating on your fresh paint. But now is a good time to practice on smaller panels, getting the mixtures right, etc.

And stick with the same brand throughout. Body fillers, sealers, primers, colors and clears, reducers, activators, etc. Stick with the same line of products, as they are made to work with eachother. Otherwise, you can run into some funky chemical reactions :lol: We had mixed brands a while back, and everywhere that we had body filler, the paint ended up changing colors a few months later from silver, to like a peach color. :lol:

Greg E
12-13-2010, 02:38 PM
You guys got a Nason color chart? Looks like their products aren't available to the general public... :(

Hans@GZP
12-13-2010, 03:41 PM
Find a color of a car that you like and give me the code. They really don't do tri coats, but just single stage and base/clear setups. I don't have any color books... I just go by color codes. Whenever I see a color of a car I like, I jot down in my phone what make/model and approximate year and I hunt for it. Like, my next pearl white car is going to be from a Lexus IS250/350. They have a crazy sick pearl white that I fell in love with. We just finished painting an M3 Carbon Black on a 3000GT and it looks nuts. I just see colors and jot them down for the next time I do a full paint job. If it's close to the original color (I won't paint an original black car white) I pick it from my list and paint it that color. It really doesn't cost any more to paint a car a non-factory original color, so why not customize :)

Make sure you use a 2k primer and not a 1k primer. 1k primers tend to bleed through the paint. They do dry extremely fast, but they aren't a great surface to start a good paint job on.

Greg E
12-13-2010, 04:21 PM
How about the electric blue found on the 05/06 evo or the danube blue the 3/s came in? How much for the paint, clear and primer? Keep in mind im doing the inside of the car too.

stealthee
12-13-2010, 06:44 PM
You guys got a Nason color chart? Looks like their products aren't available to the general public... :(

Nason is available to the public. You just have to find a store that sells it. There is a place called Paintmasters here that sells it. In fact my car was painted using Nason.

Oh, and yes you can clear single stage. We did it with my Bronco II I had. It definitely added shine to it.

There is another method you can use where you actually mix the clear with the color in several stages using slightly different mixes each stage. It ends up looking excellent, but does entail some work.

stealthee
12-13-2010, 06:47 PM
How about the electric blue found on the 05/06 evo or the danube blue the 3/s came in? How much for the paint, clear and primer? Keep in mind im doing the inside of the car too.

Oh forgot this. I would recommend at least 1.5 gallons if you are doing door jams and under hood. If you are doing the complete interior I would get at least 2 gallons. That is unmixed too so it will end up netting you closer to 2 full gallons sprayable if you go with 1.5 gallons. We used 1 gallon when we did my car and we BARELY made it. If there would have been any major mistakes I would have had to go get more, and then I would have been screwed because my car has pearl in the paint and getting it to match would have been next to impossible.

Chris@Rvengeperformance
12-14-2010, 01:17 PM
yeah if you get any paint, get a quart extra for later touch ups.

RL7
12-14-2010, 02:15 PM
Nason works fine but it doesn't cover very well at all. You will have to do at least 3 coats of base and probably 4 or 5.. I like the ppg omni line much better for base colors. Nason is 2:1 and omni is 1:1, so you get a lot more sprayable product with ppg and even at 1:1 it seems to cover better than Nason. The clears all seem pretty similar, last one I used was a super budget line "Advantage" over ppg base and it came out glassy without any buffing.

May want to consider waterborne- that's where everything will be in 10 years and it's probably better for your heath. I sprayed a bunch of pipes with industrial waterborne paint and I liked it a lot. You really had to try hard to run it. I'm not sure how that compares to the automotive stuff though.

Chris@Rvengeperformance
12-14-2010, 02:20 PM
yeah I sprayed omni on my sideskirts and it came out pretty well. I think I used a nason clear over the top, but it is best not to mix products.

The omni was only $33 a quart, so it isn't heart breaking when you mess up.

Greg E
12-14-2010, 03:17 PM
May want to consider waterborne- that's where everything will be in 10 years and it's probably better for your heath. I sprayed a bunch of pipes with industrial waterborne paint and I liked it a lot. You really had to try hard to run it. I'm not sure how that compares to the automotive stuff though.

The pearls and metallic paints sold by eastwood are all waterborne. I am still considering their pearl blue.

stealthee
12-14-2010, 05:22 PM
Nason works fine but it doesn't cover very well at all. You will have to do at least 3 coats of base and probably 4 or 5.. I like the ppg omni line much better for base colors. Nason is 2:1 and omni is 1:1, so you get a lot more sprayable product with ppg and even at 1:1 it seems to cover better than Nason. The clears all seem pretty similar, last one I used was a super budget line "Advantage" over ppg base and it came out glassy without any buffing.

May want to consider waterborne- that's where everything will be in 10 years and it's probably better for your heath. I sprayed a bunch of pipes with industrial waterborne paint and I liked it a lot. You really had to try hard to run it. I'm not sure how that compares to the automotive stuff though.

Omni is a generic of a generic. Nason is Dupont in a different container. It covers very well.

If I remember right we did 3 coats and had no coverage issues. They were all lighter coats too. Also I think we used a Montana clear. It is one of the better clears out there thats not too outrageous in price.

1992redvr-4
12-14-2010, 05:47 PM
The pearls and metallic paints sold by eastwood are all waterborne. I am still considering their pearl blue.

You sure they are waterborne?

I work at a body shop as a painter and I spray Sherwin-Williams paints including their AWX waterborne paints. Water based paints are kinda aggrivating b/c you have to have the driers blowing on the basecoat to dry it.

I've sprayed single stage paints, including a 3000gt with a large metallic silver. Its hard to work with. If you mess up, you have to start all over. At least with basecoat/clearcoat you can sand the basecoat.

Clear can be sprayed over a single stage paint for a smoother look, also for UV protection.

There are all kinds of good paints out there. Omni is a generic of PPG. I've sprayed it before. Most Carquest's sell Omni paints. Western brand clearcoat is a good clear for a budget.

Chris@Rvengeperformance
12-14-2010, 06:27 PM
Omni is a generic of a generic. Nason is Dupont in a different container. It covers very well.

If I remember right we did 3 coats and had no coverage issues. They were all lighter coats too. Also I think we used a Montana clear. It is one of the better clears out there thats not too outrageous in price.

What are you talking about? PPG makes Omni, same as Dupont makes nason.

1992redvr-4
12-14-2010, 06:38 PM
Here is where I get to spend all day........painting away.

There is about 13K worth of basecoat on that shelf.... not including reducers, clearcoats, and everything.
http://i254.photobucket.com/albums/hh95/1992redvr-4/IMAG0316.jpg

Booth and mix room cost about 80K installed.
http://i254.photobucket.com/albums/hh95/1992redvr-4/IMAG0317.jpg

Chris@Rvengeperformance
12-14-2010, 06:40 PM
want to paint my car? Lamp Black would be good :)

RL7
12-14-2010, 06:49 PM
Do you have to dry the waterbornes or can you just flash it for a really long time? That could probably lead to a lot of crap in the paint if you didn't have a booth.

As far as I know, Omni is one of PPG's budget lines and Nason is Dupont's budget line. Both are basically the previous formulation of their paints. Coverage will depend a lot on the color and how much reducer you use.

Chris@Rvengeperformance
12-14-2010, 06:54 PM
I'm not an expert, but all the shows I've seen show that they put a lot more fans and heat in the water bourne paint booths to help the dry time.

stealthee
12-14-2010, 07:00 PM
Omni is cheap no matter how you buy it. Nason can still get expensive easily.

What that means about quality, I don't know, but I have seen Omni, and I have seen Nason and would take Nason 100 times over Omni.

Greg E
12-14-2010, 09:06 PM
I'm cool with spending the $$ on lamps and heaters for waterborne paints. The ease of the spray application would be worth the time in fixing runs.

1992redvr-4
12-15-2010, 09:23 AM
want to paint my car? Lamp Black would be good :)

I could make it happen, but hopefully the next 3S I paint will be mine....lol.


Do you have to dry the waterbornes or can you just flash it for a really long time? That could probably lead to a lot of crap in the paint if you didn't have a booth.

As far as I know, Omni is one of PPG's budget lines and Nason is Dupont's budget line. Both are basically the previous formulation of their paints. Coverage will depend a lot on the color and how much reducer you use.

You have to use driers or fans to dry the paint. I've got some air amplifiers here at work I use. Some have "squirrel cage" fans mounted in the booth to dry paints. You have to let the waterborne paint sit for a minute or two then slowly force air on it to dry it. Hot or humid day...... FML. It takes forever on a hot or humid day to dry.



I'm cool with spending the $$ on lamps and heaters for waterborne paints. The ease of the spray application would be worth the time in fixing runs.

Waterborne paint is not easily sprayed. Its alot harder than your average basecoat. It can't be sprayed over any bare metal spots. Tho it does cover good, its hard to get used to. The driers are not cheap either.... If you've got the time and money, I'd say go for it, but you may regret it in the end.

Greg E
12-15-2010, 01:34 PM
Waterborne paint is not easily sprayed. Its alot harder than your average basecoat. It can't be sprayed over any bare metal spots. Tho it does cover good, its hard to get used to. The driers are not cheap either.... If you've got the time and money, I'd say go for it, but you may regret it in the end.

I was going to steal the driers from work so the cost is nothing. I'm also soda blasting and priming all the metal parts of the car. The plastic pannels are getting scuffed by.hand and primed.

If the spray is really difficult maybe i'll stay away from it though.

1992redvr-4
12-15-2010, 02:57 PM
I was going to steal the driers from work so the cost is nothing. I'm also soda blasting and priming all the metal parts of the car. The plastic pannels are getting scuffed by.hand and primed.

If the spray is really difficult maybe i'll stay away from it though.

Are you gonna be spraying the car in a booth? If so, then go at it. Its just the waterborne paint is aggrivating to work with. It would be hard (to me anyways) to spray a complete car with waterborne, unless you were panel painting. Then color match may be an issue. A solvent-based basecoat is much easier to work with, don't have to mess with the driers and such. Also, it is recommended that waterborne paints be sprayed with a stainless steel gun.... I guess pro-longed use would cause rust in other guns. We bought a $700 digital Sata gun to spray waterborne paints.

RL7
12-15-2010, 04:54 PM
Omni is cheap no matter how you buy it. Nason can still get expensive easily.

What that means about quality, I don't know, but I have seen Omni, and I have seen Nason and would take Nason 100 times over Omni.

Where is omni cheap? Last time I bought Omni or Nason, they were comparable in price (in the $100/gal ballpark). If I can get Omni cheaper somewhere, it would be good news for me. I have bought, sprayed, and observed the finished jobs with both paints. Just because you have one job that looks nice with Nason and one that looks bad with Omni doesn't necessairly mean Nason is better. The painter and the clear has a lot more to do with it. I've sprayed half my stealth with Nason base and clear and it looks fine. Just about all my painting has had some sort of pearl in it, so I can almost never just sand out imperfections. That tends to make you a little picky with paints and I just like spraying Omni better. I've used PPG Deltron and Omni and the Omni actually is pretty similar to the Deltron where Nason and Chromabase are pretty different. Before you say Omni is cheap or infer that it's a bad paint, try it out. This is basecoat I'm talking about here. I usually use Nason clears and I generally like them. Although this "Advantage" brand clear is cheaper and looks pretty good so far.

Greg E
12-15-2010, 05:25 PM
Are you gonna be spraying the car in a booth? If so, then go at it. Its just the waterborne paint is aggrivating to work with. It would be hard (to me anyways) to spray a complete car with waterborne, unless you were panel painting. Then color match may be an issue. A solvent-based basecoat is much easier to work with, don't have to mess with the driers and such. Also, it is recommended that waterborne paints be sprayed with a stainless steel gun.... I guess pro-longed use would cause rust in other guns. We bought a $700 digital Sata gun to spray waterborne paints.

It's a stainless gun.

I had contemplated bringing the car to work to paint it but it's not worth the hassle. It'll be painted in pieces.