View Full Version : New parts in means updates to the FNR Stealth section
I've got some new parts in so, as always, that means new additions to the Stealth section of the Far North Racing website.
http://farnorthracing.com/stealth/index.html
Enjoy!
DG
DocWalt
12-08-2010, 11:40 PM
Awesome. Good to see you over here, and thanks for the update.
rez604
12-09-2010, 01:42 AM
love your site. keep em comin
Amphiron
12-09-2010, 07:04 AM
bookmarked the write up on programming the MAF into AEM. Thanks.
Hans@GZP
12-09-2010, 09:34 AM
Great read on setting up the AEM EMS to control boost. When I first started tuning AEM EMS's I had similar problems with oscillation in boost. It's good to see you figured it out.
CoreyB
01-19-2011, 05:39 PM
Nicely done.
Updates to the driveshaft page, and a new page for the high flow cat.
Not exactly compelling reading, but every little bit helps, wot?
DG
Updates to the driveshaft page, and a new page for the high flow cat.
Not exactly compelling reading, but every little bit helps, wot?
DG
Indeed...good stuff.
CoreyB
04-05-2011, 11:21 AM
Just read your driveshaft write up. I suspect you need new motor mounts to fix the vibration issue under load.
I did the motor mounts a couple of years ago. I don't think that's it.
DG
EvanH
04-05-2011, 11:44 PM
Reading all of your stuff; You had said the vibe happened after you hit the curb? Do you think the bushings on your front left lower control arm or rear left trailing and control arms got damaged? When power is applied, I would think that could cause a shimmy of the wheel back and forth in a manner that could produce the problem.....Its only a thought, so let me know if I am wrong.
The vibe first occurred following the wheel swap. That in turn followed the installation of a pair of 13Gs and the upper Y pipe.
It occurs only under very specific circumstances - high speeds (90-130 km/h) high gear, under load but part throttle (~25% or so or a little higher)
I first noticed it pulling onto a freeway from an on-ramp. I thought I had wandered onto the rumble strips on the side of the road, because that is exactly the sound and frequency of the vibration. It is very violent.
It's not a speed-related issue. It's not that I have a vibration at x km/h, which is normally what indicates a wheel out of balance or something suspension related. Instead, I think it's related to that particular load condition that only occurs in those specific circumstances. That suggests AEM tune related, or possibly a leak somewhere in the intake track that only opens up (enough to matter) under high vacuum.
I know for a fact that I have a stripped bolt hole in the manifold EGR pipe (only recently discovered). It may be leaking enough air into the motor to throw off the tune. Or maybe an injector seal is leaking. I'm not sure. This one is baffling.
The crazy part is the nature of the symptom - the vibration. I know what a misfire sounds like, and this is way too regular to be a "normal" misfire. It could, maybe, be some sort of program-generated misfire (similar to a traction control misfire) - to the point where I double-checked my AEM cal to make sure I hadn't accidentally enabled TC and had some weird parameters turned on that caused it to engage at that time.
Bottom line is that I have a list of known faults and I'm slowly iterating through them. I know that EGR pipe leak needs to be fixed. I know that my injectors are maxxed out so I have a set of DSM injectors to go in (and new seals too). Eventually I'll either fix the fault that rectifies the problem, or I'll exhaust the list of known faults and at least narrow down the list of what it isn't.
DG
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.