View Full Version : Mysterious black box
GordonRamsey
11-14-2010, 04:51 PM
Could someone please tell me what that black box is underneath the passenger seat and how on Earth I get those screws loose to get it out??
AshyBone
11-14-2010, 05:01 PM
I had to go into the garage and check and see if I had one too. Is what your talking about under the carpet because I don't have anything just sitting there. The only thing I can think of is a stock amp. I know DSM's have a black box under the passenger seat so that might be the same thing. I don't know for sure though.
GordonRamsey
11-14-2010, 05:02 PM
It looks like it could be an amp. Its not covered. But for the carpet to come out that needs to. stupid planning.
J_Parker
11-14-2010, 05:04 PM
black box is underneath the passenger seat
I have mine ripped appart right now and I have no black box anywhere near my passengers seat, could it be an aftermarket thing? Only things I know of in the passengers area are:
- Behind kick panel under dash, Cruise control module
- Side of center console, MFI
- Behind back seat side panel, ABS module
- There is one box on the passengers side under the glove compartment that I never did figure out what is for, perhaps this could've been relocated?
There is howeve a small heat sink looking box just behind the drivers side front seat mount on mine, perhaps they could be of similarity, do you think you can get us a picture?
Another thing it could be is an ass switch for your seatbelt :p
J-Groove
11-14-2010, 05:09 PM
It is the stock stereo amp.
To remove it I would think you may have to take out the seat. At least that would be the easiest way.
-John
J_Parker
11-14-2010, 05:15 PM
It is the stock stereo amp.
To remove it I would think you may have to take out the seat. At least that would be the easiest way.
-John
Is this a 2G thing? Mine (had) the stock infinity amp behind the factory head unit. Never seen them on the floor before except for my old RX-7 :p
stealthee
11-14-2010, 05:17 PM
For the carpet to come out the seats need to come out anyway since the carpet goes over the studs and under the seat rails.
J_Parker
11-14-2010, 05:21 PM
For the carpet to come out the seats need to come out anyway since the carpet goes over the studs and under the seat rails.
Haha, reading FTW! I missed that :p
GordonRamsey
11-14-2010, 05:39 PM
Yes I know all that other stuff has to come out. Because it already is, but yes those screws are on there. And I'm guessing that's what that connector is underneath the drivers seat? I don't remember if my passenger had one. haha. Man these things are a pain in the ass, so many hidden screws that dont need to be where they are.
SupraMKIII
11-14-2010, 10:03 PM
Take out the passenger seat, then remove the two screws holding the amp in on the rear side of the car. Then you should be able to unplug the connectors and pull the amp out.
GordonRamsey
11-15-2010, 08:46 PM
haha I think these screws are loc-tighted, I'm going to have to rig a tool.
J_Parker
11-15-2010, 09:35 PM
haha I think these screws are loc-tighted, I'm going to have to rig a tool.
I have the perfect tool for you! It's a sharp edge with a handle, and something heavy to hit it with :D Otherwise known as a cold chisel and a hammer... The two have come to be very hand for me ;)
gs1000kat
11-16-2010, 10:13 AM
For the carpet to come out the seats need to come out anyway since the carpet goes over the studs and under the seat rails.
The carpet does not need to come out, at least not in my 99. The carpet is cut so that the flaps will pull out of the way.
Only way I know to remove it is to pull the seat. Not a big job at all. 4 bolts and a plug or two. The rear outside bolt can be a bitch to get to though. Be sure you have the seat as far forward as it can go.
gs1000kat
11-16-2010, 10:18 AM
It looks like it could be an amp. Its not covered. But for the carpet to come out that needs to. stupid planning.
Stuoid planning? It's either pull the carpet to get the amp out or oull the amp to get the carpet out. How often do you think most owners are going to actually pull their carpet? Probably more likely they will pull the amp, so it's actually good planning.
BTW, My screws came out just fine. I don't think there is any Loctite on them. Maybe some rust though. I'd throw some PB Blaster or similar penetrating oil, put a screwdriver in the slot, then tap it with a hammer a few times
GordonRamsey
11-16-2010, 10:34 AM
I will try that today.
GordonRamsey
11-16-2010, 03:01 PM
Wow, those are in there. They are stripping now, with me standing up and putting all the possible weight on them I can. Stupid useless stereo systems.
SupraMKIII
11-16-2010, 03:02 PM
I couldn't get mine out with a screwdriver but a drill with a phillips bit did the trick just fine.
GordonRamsey
11-16-2010, 03:11 PM
My drill cant handle the torque. I tried it. haha
GordonRamsey
11-16-2010, 03:25 PM
just broke my drillbit. (sigh)
SupraMKIII
11-16-2010, 04:34 PM
I probably would've gotten pissed enough to just drill them out at that point, haha
bluemax_1
11-16-2010, 05:19 PM
Impact drivers are great things. Useful in many situations (this being one of them, the other being replacing the stock pump). If you've already stripped the bit though, then you'll need to drill it out or use something like an EZ-Out.
Max
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.