PDA

View Full Version : 90mm TB mod--Thread for those wanting to do it



vr4_rider
11-07-2010, 01:31 AM
Hey, guys. I'm very new to this idea, but would like to perform this mod.

I would like this thread to be an informational one with the purpose to help those who are interested in the 90mm throttle body.

If you have perform this mod, or know how to, please post up.

I'll start the questions:)

1) What throttle bodies will work?
2) Can we use the stock plenum?
3) Who makes adapters?

Here's what I found on ebay:

http://cgi.ebay.com/ebaymotors/Q45-Throttle-Body-Adapt-Plate-RMR-088-Made-USA-_W0QQcmdZViewItemQQhashZitem3cadbacf6aQQitemZ26061 2738922QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccesso ries

http://cgi.ebay.com/ebaymotors/DNA-80MM-UNIVERSAL-THROTTLE-BODY-CNC-BILLET-ALUMINUM-_W0QQcmdZViewItemQQfitsZModelQ3aQ5145QQhashZitem25 5eba1827QQitemZ160503044135QQptZMotorsQ5fCarQ5fTru ckQ5fPartsQ5fAccessories

Here's one for a 3000GT/Stealth:

http://cgi.ebay.com/ebaymotors/90-99-3000GT-Stealth-70MM-THROTTLE-BODY-CNC-Billet-_W0QQcmdZViewItemQQhashZitem1c16d9c027QQitemZ12064 2453543QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccesso ries

Thanks,
TP

Gene
11-07-2010, 01:46 AM
WHY do you need a 90mm tb?
are you planning on making over 1100 awhp?
you realise its going to make driveability total shit right?
tuning it is gonna be a pain in the butt too.

x2xtreme360
11-07-2010, 01:59 AM
Zero reason to upgrade from the stock 60mm one. It's one of those pointless kind of mods... as it wont do you any good.

vr4_rider
11-07-2010, 01:20 AM
Oh..lol. Ignore this thread then..haha. I had no idea it was pretty much useless for the general population.

But the 90mm is really a 82mm ID, so I don't know if the "over 1100 awhp" comment was for the 90mm ID or OD.

As to why, I thought upgrading would make things flow better. My IC piping is 3" and the stock tb is 2.44" (62mm).

The reason why I mentioned 90mm was because that is what's common with TB upgrades.

So for 600awhp-700awhp, what's a good upgrade TB, if any?

Would the AEM EMS 2 take care of the shitty drivability? and would tuning be an issue with the AEM EMS 2?

Thanks,
TP

Patryn
11-07-2010, 01:25 AM
CX racing has that billet one that is selling on Ebay and PMP also sells them. I has "bling" factor to it, gets rid of the water lines, and is 3 inch in diameter to mate well with most FMIC piping which is 3 inches anyway.

http://cgi.ebay.com/ebaymotors/90-99-3000GT-Stealth-70MM-THROTTLE-BODY-CNC-Billet-_W0QQcmdZViewItemQQhashZitem1c16d9c027QQitemZ12064 2453543QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccesso ries

vr4_rider
11-07-2010, 01:25 AM
Here are the links for the billet tb:

http://www.pricematchedparts.com/products/3000gt_Stealth_Billet_Throttle_Body-3850-20.html

http://cgi.ebay.com/ebaymotors/90-99-3000GT-Stealth-70MM-THROTTLE-BODY-CNC-Billet-_W0QQcmdZViewItemQQhashZitem1c16d9c027QQitemZ12064 2453543QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccesso ries

I take it the q45 TB won't work with a STOCK plenum?

oohnoo
11-08-2010, 11:46 AM
I have that CXRacing one but haven't had the chance to install it yet. It looks to be a nice TB as it uses both the oem TPS and ISC/IAC which retain the water lines for the ISC to work properly. Look at the pic that shows the bottom where it has two plugs, you have to remove those and install fittings which are not supplied. Also this will not bolt up to the stock plenum as the bottom portion of it hits the rear valve cover, maybe if you used one of the plenum spacers.
I'm going to be using a aftermarket plenum from PNTPerformance which is already bored out for 75mm. Lots of good features with this plenum.

http://i301.photobucket.com/albums/nn61/oohnoo_VR4/186016040_tp.jpg

mb7050
11-08-2010, 12:18 PM
Nice intake mani indeed.
http://img.auctiva.com/imgdata/9/0/9/3/4/5/webimg/186019555_o.jpg
http://img.auctiva.com/imgdata/9/0/9/3/4/5/webimg/186015964_o.jpg

oohnoo
11-08-2010, 12:40 PM
Ya but it took alot of work to get it to fit properly. The mounting flange was warped to shit so I had to set it up on the miller and take off about .035" to get it flat. I'm also hoping it's going to clear the Tial wastegate on my DR setup.



Nice intake mani indeed.

vr4_rider
11-08-2010, 01:32 PM
I have that CXRacing one but haven't had the chance to install it yet. It looks to be a nice TB as it uses both the oem TPS and ISC/IAC which retain the water lines for the ISC to work properly. Look at the pic that shows the bottom where it has two plugs, you have to remove those and install fittings which are not supplied. Also this will not bolt up to the stock plenum as the bottom portion of it hits the rear valve cover, maybe if you used one of the plenum spacers.
I'm going to be using a aftermarket plenum from PNTPerformance which is already bored out for 75mm. Lots of good features with this plenum.

http://i301.photobucket.com/albums/nn61/oohnoo_VR4/186016040_tp.jpg

Hey, Bob. IF one were running an AEM EMS 2, what features of the TB can you get rid of? What about the water lines running to the TB?

The CXracing won't work with a stock plenum? How do you know?

Thanks,
TP

oohnoo
11-08-2010, 01:36 PM
not sure by your statement....What features would you WANT to get rid of?

I test for it. You probably can get it to fit if you filed the corner off the bottom where it was hitting, but I'd don't think the water lines would fit them. I can take a looksee again if you want as I have a test motor I use for my fuel setups.

vr4_rider
11-08-2010, 03:02 PM
Hey, Bob. You don't have to see.

I was wondering if, with an AEM EMS2, one can just run a TB with a TPS on it...no ISC/IAC, no coolant lines, etc...What's the minimum needed on the TB to have a properly operating car ? I am trying to simplify the engine bay.

MR2
11-09-2010, 03:09 AM
just use a spacer :p

dumb question alert...do the water lines do much? in what conditions does heating the intake help?

oohnoo
11-09-2010, 09:38 AM
I think.....I think..... the water lines are for the ISC/IAC as it senses the coolant temps for idle control. Yep called it on the money.
http://www.stealth316.com/2-isc-iac.htm



just use a spacer :p

dumb question alert...do the water lines do much? in what conditions does heating the intake help?

Unknownvr4
11-09-2010, 12:14 PM
Oh... I bypassed the TB lines so i dont heat up my intake...

x2xtreme360
11-09-2010, 12:19 PM
just use a spacer :p

dumb question alert...do the water lines do much? in what conditions does heating the intake help?


I think.....I think..... the water lines are for the ISC/IAC as it senses the coolant temps for idle control. Yep called it on the money.
http://www.stealth316.com/2-isc-iac.htm

I don't think the ISC has anything to do with the coolant lines. The coolant lines are for the FIAV. The FIAV is open during cold starts to allow more air to bypass. Once it warms up, it closes.

I opened my TB up and sealed off the FIAV ports so my car idles like it's warm all the time.

oohnoo
11-09-2010, 12:59 PM
Yep you're correct...my bad. http://www.stealth316.com/2-isc-iac.htm

So this is a good thing as I probably would have connected them and wrecked all kinds of havic. Damn that would have been fun :o




I don't think the ISC has anything to do with the coolant lines. The coolant lines are for the FIAV. The FIAV is open during cold starts to allow more air to bypass. Once it warms up, it closes.

I opened my TB up and sealed off the FIAV ports so my car idles like it's warm all the time.

vr4_rider
11-09-2010, 01:19 PM
From Jeff's site:

"servo is used by the engine control unit (ECU) to control basic idle speed. The ECU also uses the ISC servo to adjust idle speed as engine load changes or increase airflow.."

Does that mean I can get rid of it if I went AEM EMS 2 without disadvantages?

Sorry for newbie question.

J. Fast
11-09-2010, 02:08 PM
With AEM EMS you can remove the ISC vr4_rider. As long as your not driving under constant vac conditions you will have no ill effects. You can program your idle with the EMS and tweak the idle stop screw if you have problems with idle or hard starting. If you remove it and block the FIAV you will need to bump up the idle or feather the gas pedal until your car warms up and also feather the pedal if you load up the engine, say for example you turn on the AC and you come to a stoplight. If you want to clean up the engine bay I would recc bypassing the FIAV and keeping the ISC. You'll have to tune out the surging tho.

oohnoo
11-09-2010, 03:21 PM
So maybe the CXRacing throttle body may prove to be worthy as you can keep the ISC.

J. Fast
11-10-2010, 04:23 AM
I'd have to agree with that one. Unless you're on the throttle all the time and it's a racecar it's probably a good thing to have for city driving.

Got any info or links for the CX TB adapter plate oohnoo? Does that come with a FIAV bypass?

TUFFTR
11-10-2010, 06:29 AM
I was without an idle motor for close on a year. Now it's wired in and it's MUCH better. Hardly ever stalls.....still a WIP getting the thing to start and idle perfect 100% of the time.

Features like the idle motor well, I just don't see on a DD why you'd get rid of it.

oohnoo
11-10-2010, 09:12 AM
No adapter plates but it is the same bolt pattern. Only thing you'll have to do is bore out the plenum to match.
Not sure on the FIAV, I'll have to take a better look at it but I don't think it comes with one


I'd have to agree with that one. Unless you're on the throttle all the time and it's a racecar it's probably a good thing to have for city driving.

Got any info or links for the CX TB adapter plate oohnoo? Does that come with a FIAV bypass?

GTOJOE
11-11-2010, 07:59 AM
Quick Q on the PNT manifold. Can you get to the rear spark plugs with it on? or is there any manifolds available that allow this?

mb7050
11-11-2010, 08:31 AM
if i remember right dr intake and ultimate performance intake will allow you to change change rear plugs ..

oohnoo
11-11-2010, 09:12 AM
NOPE, this thing has a huge surge tank.


Quick Q on the PNT manifold. Can you get to the rear spark plugs with it on? or is there any manifolds available that allow this?

J. Fast
11-11-2010, 10:57 AM
Do they offer it with a drive side exit?