View Full Version : 99 Montero ECU, 92 Stealth TT
aaronatstate
10-26-2010, 12:18 AM
After some investigation, it was discovered that 98 and 99 Montero ECUs shared the same circuit board with 98 and 99 VR4s. There are a few differences in the boards. The Montero board is missing 39 pieces, and has 4 that the VR4 board does not.
However, most of these missing pieces, are not needed for the majority of people who want a tuneable ECU. They are for things like the stock boost gauge, boost control, active exhaust, and a few other small things. One thing its missing is 2 of the 4 02 sensor paths, not a big deal for 1g cars, but the stuff would need to be soldered on for 2g's, or people who need OBDII. The most major thing missing, is the 3 pieces in the knock sensor circuit. Once the correct surface mount parts are soldered in, it works just fine.
Anyway, I had an adapter harness made for me, that included an OBDII port, and flashing enabler cable. I got it from a Brett, and it is awesome. The only problem was the AC controls weren't hooked up 100%, but Gatecrasher and I managed to figure it out, and got the AC working.
So Gate and I got it installed, and we flashed 99 VR4 code onto the ECU. Flashed it for 450cc injectors, and started it up. Started up like stock. After doing a few test drives, was getting knock, just like my original ECU with SAFC. Got into editing the timing tables. First thing that needed to be done was to account for the latency differences between the 1g cam sensor, and the 2g cam/crank setup. After calculating that at different RPMs, and taking out an additional 2 degrees for my higher compression pistons, and all the knock went away. Also all the knock I was getting at low RPMs and high load, i.e. flooring it in 5th at highway speeds is now gone as well.
So I know have a 92 Stealth TT, running a 99 Montero ECU, with 99 VR4 code. I have 13t's set to 14psi, 450cc injectors, all the other supporting modes, running 91 octane, and not a lick of knock. Also have a fully flashable ECU, and the best part is, my total investment will be about $450 bucks, for the ECU, harness, and a Tactix Openport 2.0. Another amazing thing is, it has 100% stock driveability, I got 24.4mpg with it, and its only using 1 02 sensor for right now, and no tuning has been done on the closed loop stuff yet.
TL : DR - 99 Montero flashable ECU with 99 VR4 code running a 92 Stealth TT with bigger injectors, and bigger turbos. Stock driveability, and full control.
Anyway here are some videos.
http://www.youtube.com/watch?v=4RITotowcIQ
http://www.youtube.com/watch?v=JrSBB2VshNM
http://www.youtube.com/watch?v=xwbwyo_FRjU
ChargerX3
10-26-2010, 12:50 AM
Might as well subscribe here as well...
aaronatstate
10-26-2010, 01:16 AM
Might as well subscribe here as well...
:lol2:
ChargerX3
10-26-2010, 01:44 AM
http://www.gifbin.com/bin/072009/1248715399_arctic-fox-hunting.gif
CoreyB
10-26-2010, 10:04 AM
Pretty cool. Nice work.
DocWalt
10-26-2010, 12:28 PM
Snazzy. Would this also work for hybrid owners?
aaronatstate
10-26-2010, 01:53 PM
Snazzy. Would this also work for hybrid owners?
Both Jeff and his GF have 94s. So far it has worked on his GFs car. Her car has some other small issues, like boost leaks and what not, that need to get fixed first. We did start it, and take it for a drive however. So it seems to work, but the weekend I was in KC, we spent most of our time getting my car running, so we could get some highway/cruise testing in as well on my drive home. The biggest thing with the hybrids, and OBDII pre flash cars (96-97), is the downstream cat monitoring has to be disabled for the car to run properly. This is probably most likely due to the missing 02 hardware on the Montero ECUs.
I plan on going back up to KC in a few weeks, and we can concentrate on her car more. I can update more on the hybrids at that point in time.
HLxDrummer
10-26-2010, 02:25 PM
So you get a Montero ECU, do something for the knock stuff to work (what does this involve), wire it in to the correct wires/pins, wire in an OBD2 port, buy a Tactrix cable, flash the VR4 tune and your set? That's crazy! What did you have to do with the A/C stuff?
Overall, how hard would you say it would be to get a stock car to run on this setup? My VR4 is my DD but I've installed/tuned my eManage no problem and I'm wondering if I could get away doing this on my car. I have like $450 in my eManage setup.
Also, right now I'm using the Scanmaster/MMCd to log wideband. How would I log wideband without the Scanmaster/MMCd?
DocWalt
10-26-2010, 04:11 PM
Both Jeff and his GF have 94s. So far it has worked on his GFs car. Her car has some other small issues, like boost leaks and what not, that need to get fixed first. We did start it, and take it for a drive however. So it seems to work, but the weekend I was in KC, we spent most of our time getting my car running, so we could get some highway/cruise testing in as well on my drive home. The biggest thing with the hybrids, and OBDII pre flash cars (96-97), is the downstream cat monitoring has to be disabled for the car to run properly. This is probably most likely due to the missing 02 hardware on the Montero ECUs.
I plan on going back up to KC in a few weeks, and we can concentrate on her car more. I can update more on the hybrids at that point in time.
Cool beans :)
http://www.gifbin.com/bin/072009/1248715399_arctic-fox-hunting.gif
Apparently, firefox crashes from the sheer awesomeness of this thread. :D
Snazzy. Would this also work for hybrid owners?
Probably. I'll have an answer in 2-3 weeks, hopefully.
aaronatstate
10-26-2010, 06:38 PM
So you get a Montero ECU, do something for the knock stuff to work (what does this involve), wire it in to the correct wires/pins, wire in an OBD2 port, buy a Tactrix cable, flash the VR4 tune and your set? That's crazy! What did you have to do with the A/C stuff?
Overall, how hard would you say it would be to get a stock car to run on this setup? My VR4 is my DD but I've installed/tuned my eManage no problem and I'm wondering if I could get away doing this on my car. I have like $450 in my eManage setup.
Also, right now I'm using the Scanmaster/MMCd to log wideband. How would I log wideband without the Scanmaster/MMCd?
Unfortunetly there is no EGRT pin on the flashable ECUs, but there may be other 0-5v pins that coudl be used, dont know yet.
As for a stock car, easy. My car has 13t's, 450s, and 8.3:1 Wisecos. It runs and drives just like it did when it had 9bs, 360s, and stock pistons. A/C works just like it always did, everything works just like stock. Well I shouldn't say everything. If you have stock boost control, stock boost gauge, active exhaust, stock fuel pump hi/lo relay, that stuff wont work because its not hooked up in the ECU. However, I dont have any of that stuff anymore, so it wasn't a problem for me.
HLxDrummer
10-26-2010, 08:10 PM
Could you give me a little write up on everything you had to do/buy to get it running how it is now? I could Paypal you a few bucks for the information.
aaronatstate
10-26-2010, 08:48 PM
Could you give me a little write up on everything you had to do/buy to get it running how it is now? I could Paypal you a few bucks for the information.
All I had to do was solder on the 3 pieces missing in the knock sensor circuit, get an adapter harness built that included an OBDII port and flash enable cable, use a tactix openport 2.0 with ecuflash to flash on 99 VR4 code, disable all the OBDII stuff, and thats it. Now, I also reflashed for bigger injectors (450s) and took some timing out due to the diff in sensor latencies and for my higher compression ratio. Other then that, thats all I did.
HLxDrummer
10-26-2010, 09:25 PM
Doesn't sound terrible as I already have a Boomslang "patch" harness. Just need to learn how to wire in the OBD2 and reflash stuff and where to get the connectors then find out what OBD2 stuff to disable. Any 98-99 Montero ECU will work? Does it need to be a Montero Sport?
aaronatstate
10-26-2010, 10:40 PM
Doesn't sound terrible as I already have a Boomslang "patch" harness. Just need to learn how to wire in the OBD2 and reflash stuff and where to get the connectors then find out what OBD2 stuff to disable. Any 98-99 Montero ECU will work? Does it need to be a Montero Sport?
I got a regular Montero ECU. I would stick with that as that is the only thing I can confirm works first hand. Also a boomslang will not work. It's just an extender harness. The adapter harness has to go from a 99 pin out to whatever year you have.
HLxDrummer
10-26-2010, 11:00 PM
I got a regular Montero ECU. I would stick with that as that is the only thing I can confirm works first hand. Also a boomslang will not work. It's just an extender harness. The adapter harness has to go from a 99 pin out to whatever year you have.
Ok so a regular Montero manual transmission 98-99 ECU? Doesn't have to be a particular part number other than that?
And I couldn't use the pigtails from the Montero and wire that to my stock harness?
Thanks a ton!
CoopKill
10-26-2010, 11:36 PM
My 94 has no downstream. Only the two at the manifolds.
Am I correct in saying that with proper mapping this will replace the need for something such as ARC2? If so, would an experience tuner be able to tune for upgraded fuel, turbs, and such?
RealMcCoy
10-26-2010, 11:41 PM
My 94 has no downstream. Only the two at the manifolds.
94-95 Federal cars have two sensors, Cali cars have four.
aaronatstate
10-26-2010, 11:55 PM
Ok so a regular Montero manual transmission 98-99 ECU? Doesn't have to be a particular part number other than that?
And I couldn't use the pigtails from the Montero and wire that to my stock harness?
Thanks a ton!
Automatic or manual, doesn't matter, same ECU. The trans control was separate. When I bought mine, I went on Ebay, searched for 99 Montero ECU, and bought the cheapest one. Yes, you can certainly do that. I was going to do that, until I got a harness made. You need to wire in an OBDII port, and flash enable cable for the Tactix. Brett Farnam made my harness, I'm not sure if hes going to make any more beyond the ones he's made for us testing this stuff out, but he may. I dont know if he is on this site, but he is on 3si.
My 94 has no downstream. Only the two at the manifolds.
Am I correct in saying that with proper mapping this will replace the need for something such as ARC2? If so, would an experience tuner be able to tune for upgraded fuel, turbs, and such?
Did you read my first post? I have 13t's, 450s, 8.3:1 Wiseco pistons, full exhaust no cats, hot wired walbro, and just about every other supporting mod you can have. I do not have ANY piggy backs hooked up. I reflashed my ECU for bigger injectors, and changed the timing maps, and my car runs just like stock, except its got 13t's set at 14psi. No knock, on 91 octane.
x2percentmilk
10-27-2010, 12:01 AM
Im impressed :)
Jeremy C
10-27-2010, 12:26 AM
Bah... you guys beat me to the punch. Some of the guys that are doing swaps on the Conquest are working on this same thing. Maybe I should point them here as you're way farther ahead than I am.
ChargerX3
10-27-2010, 01:28 AM
Automatic or manual, doesn't matter, same ECU. The trans control was separate. When I bought mine, I went on Ebay, searched for 99 Montero ECU, and bought the cheapest one. Yes, you can certainly do that. I was going to do that, until I got a harness made. You need to wire in an OBDII port, and flash enable cable for the Tactix. Brett Farnam made my harness, I'm not sure if hes going to make any more beyond the ones he's made for us testing this stuff out, but he may. I dont know if he is on this site, but he is on 3si.
Did you read my first post? I have 13t's, 450s, 8.3:1 Wiseco pistons, full exhaust no cats, hot wired walbro, and just about every other supporting mod you can have. I do not have ANY piggy backs hooked up. I reflashed my ECU for bigger injectors, and changed the timing maps, and my car runs just like stock, except its got 13t's set at 14psi. No knock, on 91 octane.
I really hope you guys end up doing a step by step write up on how to do this. That way we all could build them to our needs/tastes. I have no idea where most things are located on the ECU, but like most here am a quick learner.
aaronatstate
10-27-2010, 10:28 AM
I really hope you guys end up doing a step by step write up on how to do this. That way we all could build them to our needs/tastes. I have no idea where most things are located on the ECU, but like most here am a quick learner.
I have the locations of all the missing pieces, just not the values or anythign like that. I can get the values for the knock sensor circuitry, which is the most important missing link. The other stuff is not as important, because most people do not have it anymore. If you are comfortable soldering on PCBs, then its fairly easy to modify the board. I did not make my adapter harness, so I really can offer no insight about that process. But I can tell you that, you do just have to look at a 99 pin out, and a whatever year your car is pinout, and make sure the pins are connected correctly. Wiring in the OBDII port and flash enable pin, I do not know what to do with that. Im going to try and get some pics of the adapter harness this weekend, so ya'll can see what it looks like.
ChargerX3
10-27-2010, 10:32 AM
That would be great. Thanks.
HLxDrummer
10-27-2010, 08:31 PM
Ya I would be willing to pay for information like ECU part number (just to be 100% sure it will work), and knock sensor circuit information. I think I can figure out the pin out stuff/OBD port/flash enabler.
aaronatstate
10-27-2010, 08:39 PM
Ya I would be willing to pay for information like ECU part number (just to be 100% sure it will work), and knock sensor circuit information. I think I can figure out the pin out stuff/OBD port/flash enabler.
Any 98 or 99 Montero ECU will work. How many times do I have to say, all I did was go to Ebay, type in 99 Montero ECU, and bought the cheapest one. As for the knock sensor circuit there are 2 resistors and 1 capacitor missing, I dotn know the values off hand, and it will be a bit before I pull the ECU out again to check. I do know the locations, but I do not know the value.
HLxDrummer
10-27-2010, 08:47 PM
Well Brett or whoever helped you mentioned to me on the other forum that you can't just go out and get any old 98-99 Montero ECU it has to be real specific bla bla bla. So in my eyes either he is talking it up and making it sound harder than it is so he can capitalize off it (which is fine, I know he worked hard) or you got lucky grabbing a random 99 Montero ECU.
Either way, I could Paypal you a few bucks for the locations of the missing pieces and when you pull the ECU I'll pay you a bit more for the values if your cool with that. If so, just PM me how much you want and your Paypal address.
Chris@Rvengeperformance
10-27-2010, 09:34 PM
interesting, this could really benefit the platform
aaronatstate
10-27-2010, 09:37 PM
Well Brett or whoever helped you mentioned to me on the other forum that you can't just go out and get any old 98-99 Montero ECU it has to be real specific bla bla bla. So in my eyes either he is talking it up and making it sound harder than it is so he can capitalize off it (which is fine, I know he worked hard) or you got lucky grabbing a random 99 Montero ECU.
Either way, I could Paypal you a few bucks for the locations of the missing pieces and when you pull the ECU I'll pay you a bit more for the values if your cool with that. If so, just PM me how much you want and your Paypal address.
I dont need or want money. I gave you the locations and values of the knock sensor parts, thats the most important, and the only ones I know, I dont have the other values at all, just the positions, which wont do you any good unless you have a 99 VR4 ECU that you can get the values from.
Now, what Brett said on the other site is that NONE of the ECUs are direct plug n play, meaning you can't just drop them in and go (cause of stuff like the knock sensor). 98-99 Montero's WILL work, with some modification (knock sensor). AFAIK 98-99 Diamante Manual Transmission ECUs WILL work as well, with some modification. What he said is you dont want to go out and buy just any Mitsubishi V6 ECU from 98-99, cause they may not work. Thats all. I am trying to help you, you just are not listening to me.
I am not going to post any information that is not mine, without consent of all parties involved, period. I've answered all the questions I know the answers too, and posted all the pertinent information I know.
HLxDrummer
10-27-2010, 09:45 PM
I dont need or want money. I gave you the locations and values of the knock sensor parts, thats the most important, and the only ones I know, I dont have the other values at all, just the positions, which wont do you any good unless you have a 99 VR4 ECU that you can get the values from.
Now, what Brett said on the other site is that NONE of the ECUs are direct plug n play, meaning you can't just drop them in and go (cause of stuff like the knock sensor). 98-99 Montero's WILL work, with some modification (knock sensor). AFAIK 98-99 Diamante Manual Transmission ECUs WILL work as well, with some modification. What he said is you dont want to go out and buy just any Mitsubishi V6 ECU from 98-99, cause they may not work. Thats all. I am trying to help you, you just are not listening to me.
I am not going to post any information that is not mine, without consent of all parties involved, period. I've answered all the questions I know the answers too, and posted all the pertinent information I know.
Gotcha. Not trying to be a pain just want to make sure the stuff will work before I go blow money on it/sell my eManage and Scanmaster setup you know? I appreciate all the information you've given us for sure, thanks!
aaronatstate
10-27-2010, 10:45 PM
Gotcha. Not trying to be a pain just want to make sure the stuff will work before I go blow money on it/sell my eManage and Scanmaster setup you know? I appreciate all the information you've given us for sure, thanks!
Just a word to the wise, do what I did. Get the stuff when you can afford it, and don't sell your other stuff quite yet. I kept my old ECU and SAFC just in case there is a problem, because I know that setup will work :)
HLxDrummer
10-27-2010, 11:03 PM
Just a word to the wise, do what I did. Get the stuff when you can afford it, and don't sell your other stuff quite yet. I kept my old ECU and SAFC just in case there is a problem, because I know that setup will work :)
Just after I put up a thread :p It would suck to sell everything and it not work out with the Montero ECU since I put a ton of time into a clean tuning setup but I'm on stock injectors so no biggie if I have to go stock ECU for a little or anything.. We'll see although I'm really anxious to do the Montero setup.
Greg E
10-27-2010, 11:25 PM
Aaron, you're not going to be able to take advantage of my boost gauge mods, logging via EVO X map sensor nor tuning boost via the ECU. :p
ChargerX3
10-28-2010, 12:54 AM
Thanks again Aaron for the open communication. I know its hard for some, but this is big news and people are going to be asking tons of questions. I just hope they want to share the information with us. It would be a big hurdle potentially out of the way.
-steve
aaronatstate
10-28-2010, 08:06 AM
Just after I put up a thread :p It would suck to sell everything and it not work out with the Montero ECU since I put a ton of time into a clean tuning setup but I'm on stock injectors so no biggie if I have to go stock ECU for a little or anything.. We'll see although I'm really anxious to do the Montero setup.
Take the thread down? :D I dont see this not working, but its better to be safe then sorry. It's still in the testing phase.
Aaron, you're not going to be able to take advantage of my boost gauge mods, logging via EVO X map sensor nor tuning boost via the ECU. :p
Not like I can't pull the ECU out and solder on the surface mount parts ;) But I probably won't use that stuff, though it'd be ncie to have WB02 logging.
Thanks again Aaron for the open communication. I know its hard for some, but this is big news and people are going to be asking tons of questions. I just hope they want to share the information with us. It would be a big hurdle potentially out of the way.
-steve
I think most of the information will be shared in time. But like Brett said, it may just be easier to say, get this ECU from this guy, this harness from that guy, get openport from here, download this software, flash this rom on, and start tuning. :lol:
UTRacerX9
10-28-2010, 11:22 AM
Hmm, this may be a great mod for those of us who don't plan on going over 550-660cc injectors, and only running a max of 17-18 psi. Do you know how much room for growth there is with this setup? I mean, would it be possible to go full TD05 and 720 or larger injectors while still being able to tune properly?
Greg E
10-28-2010, 11:54 AM
Not like I can't pull the ECU out and solder on the surface mount parts ;) But I probably won't use that stuff, though it'd be ncie to have WB02 logging.
This isn't too hard. Especially with the rear o2 disabled in the code. Hardware wise, you'd just take the 5-volt out from the WB and install it into one of the 5v input pins. Then to keep it simple, assign that pin to a MUT address with ecuflash and tell evoscan where to find it.
The signal translation can be done in evoscan.
If you want to set this up, give me a shout and I'll walk you thru it. Ask Brett for a spare pin connector when he returns or you can just cut/splice into your adaptor harness.
The only info I need from you is which brand wideband you're running.
Greg E
10-28-2010, 11:56 AM
Btw, the same thing can be done with a map sensor if you want to log boost. There's already an input for that on your ecu as well.
Greg E
10-28-2010, 12:02 PM
Hmm, this may be a great mod for those of us who don't plan on going over 550-660cc injectors, and only running a max of 17-18 psi. Do you know how much room for growth there is with this setup? I mean, would it be possible to go full TD05 and 720 or larger injectors while still being able to tune properly?
There is no limit. You can run 2000cc injectors with e85 if you so desired. I still have to locate and disassemble the idle tables so they can be fine tuned but the ecu can calculate any fuel injector.
aaronatstate
10-28-2010, 01:46 PM
This isn't too hard. Especially with the rear o2 disabled in the code. Hardware wise, you'd just take the 5-volt out from the WB and install it into one of the 5v input pins. Then to keep it simple, assign that pin to a MUT address with ecuflash and tell evoscan where to find it.
The signal translation can be done in evoscan.
If you want to set this up, give me a shout and I'll walk you thru it. Ask Brett for a spare pin connector when he returns or you can just cut/splice into your adaptor harness.
The only info I need from you is which brand wideband you're running.
The biggest problem is, everything hooked up in my adapter harness is needed, and the things that are hooked up in the adapter harness, that aren't working, are because of missing parts in the ECU :lol: Now if I soldered on the stuff for all the 02 sensors, then I could use one of those I suppose, which would make sense actually :D I may solder the stuff for the other front 02 sensor thats not hooked up, and that will leave a rear 02 sensor hookedup that can be used as a WB02 place :chin:
Right now I dont have any open 5v sources, but we could always make one, no problem.
aaronatstate
10-28-2010, 01:50 PM
There is no limit. You can run 2000cc injectors with e85 if you so desired. I still have to locate and disassemble the idle tables so they can be fine tuned but the ecu can calculate any fuel injector.
Yup no limit. Want a 3.5 stroker with DR750s or 16g's, 760cc injectors and have it run like stock, sounds good to me :)
Greg E
10-28-2010, 02:15 PM
Right now I dont have any open 5v sources, but we could always make one, no problem.
The LC1s have a serial output that evoscan can be configured to use if you have a serial input on your laptop. USB converters are an option too.
The only draw back is then you'd have to have 2 cables connected to the laptop instead of one.
I don't have your excell spreadsheet in front of me, but I could have sworn I saw that the montero ecu did still have the map sensor input. Please correct me if I'm wrong!
Greg E
10-28-2010, 02:17 PM
Yup no limit. Want a 3.5 stroker with DR750s or 16g's, 760cc injectors and have it run like stock, sounds good to me :)
The only thing about fine tuning a 3.5 or even a car with cams is tweaking the fuel trim tables for the larger airflow. I know gate found these tables in the 94 rom. I haven't even started looking for them in the 99.
familyMAN
10-28-2010, 10:08 PM
Great info. Soooo, who's going to build me one and teach me how to use it?:D
There is a wayyyyyyy out there potential limit, depending on fuel. I've heard of people using 2150cc injectors on an evo with stock ECU, but only on e85. A local club member tried to do pump gas (93) with the 2150s and it would not idle correctly. However, there are a few cars running 1350s on pure 93 octane.
So there's a theoretical limit to it, but I doubt 99.9999% of us would ever encounter it.
aaronatstate
10-29-2010, 12:43 PM
There is a wayyyyyyy out there potential limit, depending on fuel. I've heard of people using 2150cc injectors on an evo with stock ECU, but only on e85. A local club member tried to do pump gas (93) with the 2150s and it would not idle correctly. However, there are a few cars running 1350s on pure 93 octane.
So there's a theoretical limit to it, but I doubt 99.9999% of us would ever encounter it.
Holy crap thats a ton of fuel!
donniekak
10-29-2010, 01:43 PM
Hmm, this may be a great mod for those of us who don't plan on going over 550-660cc injectors, and only running a max of 17-18 psi. Do you know how much room for growth there is with this setup? I mean, would it be possible to go full TD05 and 720 or larger injectors while still being able to tune properly?
On a fully tunable ecu, you pretty much have an aem ems. I tune my dsm with custom ecu code and have run 1600's on the stock computer at 30+psi, with launch control, nlts, native wideband, even run speed density on the stocker. This is huge.
familyMAN
10-29-2010, 07:12 PM
On a fully tunable ecu, you pretty much have an aem ems. I tune my dsm with custom ecu code and have run 1600's on the stock computer at 30+psi, with launch control, nlts, native wideband, even run speed density on the stocker. This is huge.
After you get this going on your stealth, you know where you'll be next, right;)
GTOJOE
10-30-2010, 05:22 AM
Subscribed for final results.
whitedragon
10-31-2010, 08:34 PM
Posted by Brett over on the 3SI thread that magically undeleted itself:
Part 1 - Just because the 01-03 Montero and 99 VR4 ECU have similar pin outs do not make them compatible. And yes the 01-03 Montero ECU has the same CPU as an EVO. But the EVO / 01-03 CPU is very different from the 99 VR4 (it would be like comparing an Intel and PowerPC CPU). The code would have to be entirely rewritten for the newer ECU, something I am not about to do (this is a 128K ROM File with almost 200,000 lines of machine code).
Part 2 - I already have written Big Maps into the ROM - It is just not publicly available until I am done testing. Speed Density is another re-write as well as no lift to shift, etc, etc. Both of these will be "down the road" as this is not as easy as it seems. Our ROM does not have as much free space as the EVO ROM and there is the issue of our cars not having a “working” MAP sensor input or a “clutch pedal” input to the ECU.
Ballpark - $250.00 for the conversion harness. It will not matter the year for pricing. It will include the OBDII connector for 1 Gen cars (this is how you data log and send the programming) and the reflash connector for both 1 Gen and 2 Gen (This really should be called the reflash "enable" or reflash "voltage" connector because it only supplies the reflash voltage for the ECU to accept the programming sent over the OBDII port). Still cheaper than a 3 Gen e-Manage Ultimate plug-n-play adapter from any one that makes one . . .
When the harness is publicly available, some one will post where you can get your very own.
The only other cost will be the custom modified ECU as there are no "plug and play" ECU's besides the 99 VR4 ECU. Sorry. Pricing on the modifications to your ECU and/or a pre-modified ECU are still in development because the two people who can do this (Jeff and I) have day jobs and limited amount of resources (both time and money) to buy and test the ECU's. I personally have bought over six different ECU's out of pocket for testing and Jeff has bought his fair share as well.
While there are quite a few ECU's that share commonalities with the 99 VR4 ECU, there are many surface mount component differences and this takes time to sort out. Each ECU MUST be separately qualified and then a list of changes compiled for modification. So in the beginning, don't expect to just buy any Montero or Diamante ECU and have it modified.
When the ECU is figured out, some one will post where you can buy one or send it in to be modified.
Thank you Aaron. I have spoken at great length on whether or not this should be an “open source” project with all of the key players and even some others. In the end it was decided that for now, this will not be open source. Fist off there is a great deal of complexity and specialized tools and skill sets which are required for the hardware and software (ROM) modifications. This has resulted in a lot of reading, learning, and out of pocket expenses for Jeff and I. Secondly this is far beyond the scope of the average hobbyist. Replacing failed capacitors on a 2 Gen ECU pales in comparison to the skill required for even the simplest hardware modifications on a modern surface mount ECU. You wouldn’t attempt to replace the chipset on your computer motherboard, would you? You would just buy another, right? If the SATA controller took a dive on your motherboard you would just buy another, rather than replacing the surface mount IC, right? Well this is why the hardware modifications are such an issue. And of course there are numerous other reasons why that I won’t go into here. For now everyone must be patient.
99 vr4
10-31-2010, 11:51 PM
@HLxDrummer - I have forwarded your request for a ECU mod to the person responsible for that portion of the project at this time. Since you are coming over from an e-Manage setup you are a good candidate for helping with working out any issues while tuning.
As far as size, I run a TRUE 99 VR4 with 450cc and TD04L-15G's with no problem at 9 to 10 psi. I am a little lean over that because I still have a stock FPR and I might need bigger injectors. . . . LOL
If there are any other e-Manage or e-Manage Ultimate users that want to convert, you make good beta test candidates. Please PM me or Gate and we can talk.
@Greg - yes I am on board . . . we just want to get the basics stable first . . . ROM changes are easy once you get the other stuff worked out.
prop7459
11-01-2010, 12:49 AM
Not to sound like a cheap ass but why should 94+ guys pay for a OBD2 connect? I know this is a ball park price but boomslang price their conversion harness from $150 for something like this.
terrets
11-01-2010, 02:15 AM
Will you guys give info on how to modify the ecus ourselves? I would like to do this as cheap as possible. Thanks for the GREAT discovery. :D
I would like to make my own harness also. Basically for this set up I need Evoscan + OBDII Mitsu datalog and reflash cable, 98-99 Montero ECU, OBDII port(buy from Evoscan or cut from junkyard), and Mistu Reflash Connector. Correct?
Why do you have the Tactrix Cable?
Whens the picture of your harness coming? :)
I wish I could beta test for you guys but the only thing I got to do with my EMU was datalog :(.
I cant wait for all the info on this :D This seems pretty rockin.
Thank you to all who are contributing to figuring this out.
Greg E
11-01-2010, 07:55 AM
You need the tactrix cable & obd2 to connect to the ecu.
99 vr4
11-01-2010, 09:28 AM
Not to sound like a cheap ass but why should 94+ guys pay for a OBD2 connect? I know this is a ball park price but boomslang price their conversion harness from $150 for something like this.
Actually the 2 Gen guys are not paying for a OBDII port . . . the 1 Gen guys get it for free. And since you can buy a 2 Gen 3000GT to 3 Gen Montero or 2 Gen 3000GT to 3 Gen Diamante ECU conversion harness from some one else for $150 . . . go ahead and buy it. Let me know how that works out for you.
aaronatstate
11-01-2010, 09:31 AM
Not to sound like a cheap ass but why should 94+ guys pay for a OBD2 connect? I know this is a ball park price but boomslang price their conversion harness from $150 for something like this.
The adapter harness will not be like a boomslang harness at all. 94+ guys wont need the OBD2 connection, just the reflash. If you re-read what Brett said, he said the 1G harness will include a OBDII connector, and all will get the reflash enable pin.
Will you guys give info on how to modify the ecus ourselves? I would like to do this as cheap as possible. Thanks for the GREAT discovery. :D
Not at this time. There are just to much that needs to be modified, and to many different ECUs.
99 vr4
11-01-2010, 09:45 AM
Will you guys give info on how to modify the ecus ourselves? I would like to do this as cheap as possible. Thanks for the GREAT discovery. :D
I would like to make my own harness also. Basically for this set up I need Evoscan + OBDII Mitsu datalog and reflash cable, 98-99 Montero ECU, OBDII port(buy from Evoscan or cut from junkyard), and Mistu Reflash Connector. Correct?
Why do you have the Tactrix Cable?
Whens the picture of your harness coming? :)
I wish I could beta test for you guys but the only thing I got to do with my EMU was datalog :(.
I cant wait for all the info on this :D This seems pretty rockin.
Thank you to all who are contributing to figuring this out.
Uhhh . . . in a nut shell . . . No! Information on how to modify the ECU will not be given out. Sorry. See prior post http://www.3sgto.org/showthread.php?1820-99-Montero-ECU-92-Stealth-TT&p=33139&viewfull=1#post33139
Once Again . . . Harness Adapter (retail available soon in time for X-Mass), Custom MODIFIED ECU (you supply per our part number or we supply), Tactrix OpenPort 2.0 (ONLY the 2.0 will work for programming), EVOScan v2.7 (FOR DATALOGGING), ECUFlash (For PROGRAMMING).
Total price will still be way less than retail for an AEM EMS Series 2 ($1,260.00) plus $$$$ for install and $$$$ for tuning!
AND
Priced under retail for a Greddy e-Manage Ultimate ($680.00) with a 3 Gen boom harness ($269.00)
Now I know you can find it cheaper on eBay, your cousin's uncle, or the guy down the street . . . so then go that route. I refer back to the prior post in reference to why it is the way it is.
prop7459
11-01-2010, 12:10 PM
Thanks for clearing some things up... but I have some question regarding DOHC 98-99 3s ECU's. Correct me if I am wrong but you guys are telling me it does not matter whether you have DOHC 98-99 3S ECU or a non 3S ECU you will need your harness and the ECU needs to be modify for certain things to work like the knock sensor? Have guys compared the differences between a 3s 98-99 TT ECU vs a 3s DOHC 98-99 ECU?
Greg E
11-01-2010, 12:38 PM
Thanks for clearing some things up... but I have some question regarding DOHC 98-99 3s ECU's. Correct me if I am wrong but you guys are telling me it does not matter whether you have DOHC 98-99 3S ECU or a non 3S ECU you will need your harness and the ECU needs to be modify for certain things to work like the knock sensor? Have guys compared the differences between a 3s 98-99 TT ECU vs a 3s DOHC 98-99 ECU?
No one has done the swap yet, but if all goes well, I'll be undertaking this very soon.
aaronatstate
11-01-2010, 01:38 PM
Thanks for clearing some things up... but I have some question regarding DOHC 98-99 3s ECU's. Correct me if I am wrong but you guys are telling me it does not matter whether you have DOHC 98-99 3S ECU or a non 3S ECU you will need your harness and the ECU needs to be modify for certain things to work like the knock sensor? Have guys compared the differences between a 3s 98-99 TT ECU vs a 3s DOHC 98-99 ECU?
Well the DOHC still had the knock sensor, but the pinout for each ECU wasn't identical. Tha NAs had some things the Turbos didn't and vice versa. So an adapter harness would most likely still be needed. I however, do not know without checking both ECUs out side by side.
prop7459
11-01-2010, 04:01 PM
Based on stealth316 ECM page, he listed the 98-99 DOHC and TURBO models with the same pins layout. There are a hand full of pins that are not used by the DOHC NA but are used for the Turbo Model.
Pin 41: Waste gate solenoid
Pin 48: Fuel pressure regulator
Pin 55: Turbo Fuel Pump Relay 2
Pin 75: Active Exhaust
Pin 77: Turbo Meter(Boost Gauge)
Most cars get rid of things like these. My question is what is special about your harness that boomslang or any other place that makes a conversion harness pertaining to a 3s DOHC ECU? Have guys explored the DOHC NA ECU as the most ideal ECU to use if available for Turbo models?
Here is the link on stealth316
http://stealth316.com/2-ecu94.htm
HLxDrummer
11-01-2010, 06:37 PM
Thanks for forwarding my message. Looking forward to hearing from you guys.
If you can get me setup at a reasonable price I would definitely help you guys work out the kinks/be a test subject as long as my car is still drivable during this time :p
Never tuned AEM or anything but I've nailed down airflow, timing, and boost on the eManage plus lots of logging/reading.
99 vr4
11-01-2010, 10:33 PM
Based on stealth316 ECM page, he listed the 98-99 DOHC and TURBO models with the same pins layout. There are a hand full of pins that are not used by the DOHC NA but are used for the Turbo Model.
Pin 41: Waste gate solenoid
Pin 48: Fuel pressure regulator
Pin 55: Turbo Fuel Pump Relay 2
Pin 75: Active Exhaust
Pin 77: Turbo Meter(Boost Gauge)
Most cars get rid of things like these. My question is what is special about your harness that boomslang or any other place that makes a conversion harness pertaining to a 3s DOHC ECU? Have guys explored the DOHC NA ECU as the most ideal ECU to use if available for Turbo models?
Here is the link on stealth316
http://stealth316.com/2-ecu94.htm
I don't need the link to Stealth316. I am well aware of the differences in the pin outs between the two ecus.
Of course the DOHC NA is the most ideal. The knock sensor circuits are the same. Do you think that we are stupid here? Due to the rarity of the 3000GT it was decided to find another replacment as the DOHC NA ECUs are still very expensive (if you can find one). The Montero and Diamante are much more popular and Mitsubishi started putting flashable ECUs in their cars in the beginning of 1998. Only the later 1998 3000GT had flashable ECUs. So this opens up a large variety of ECUs that will work with modification.
As far as the harness is concerned. I suggest you learn proper english as "My question is what is special about your harness that boomslang or any other place that makes a conversion harness pertaining to a 3s DOHC ECU?" is not proper english and I have no idea what you intended to say. I can only guess that you want to know what makes the harness special. The harness adapts your pre 99 factory harness to the proper plugs and pinouts for a 98/99 Montero or Diamante ECU without you having to hack into your stock wiring harness. Since you seem to have the answers, I guess you don't need a harness.
bridge
11-01-2010, 11:55 PM
Only the later 1998 3000GT had flashable ECUs.
This made my night. sorry aaron, i'm a jerk :D
prop7459
11-02-2010, 12:06 AM
I don't need the link to Stealth316. I am well aware of the differences in the pin outs between the two ecus.
Of course the DOHC NA is the most ideal. The knock sensor circuits are the same. Do you think that we are stupid here? Due to the rarity of the 3000GT it was decided to find another replacment as the DOHC NA ECUs are still very expensive (if you can find one). The Montero and Diamante are much more popular and Mitsubishi started putting flashable ECUs in their cars in the beginning of 1998. Only the later 1998 3000GT had flashable ECUs. So this opens up a large variety of ECUs that will work with modification.
As far as the harness is concerned. I suggest you learn proper english as "My question is what is special about your harness that boomslang or any other place that makes a conversion harness pertaining to a 3s DOHC ECU?" is not proper english and I have no idea what you intended to say. I can only guess that you want to know what makes the harness special. The harness adapts your pre 99 factory harness to the proper plugs and pinouts for a 98/99 Montero or Diamante ECU without you having to hack into your stock wiring harness. Since you seem to have the answers, I guess you don't need a harness.
Dude get off your high horse. Yes I had a run on sentence but you knew what I was talking about. I clearly stated what ECU I have in both threads and no one answered my question. I posted the pinouts for Arron who was not sure if pins are the same between a 3S 98-99 Turbo and NA ECU. You directed my posts to buy your harness and nothing else would work!!! I would still need a harness since my car is a 95 TT. I don't have the answers but I know enough when someone is not answering my questions.
whitedragon
11-02-2010, 01:11 AM
Dude get off your high horse. Yes I had a run on sentence but you knew what I was talking about. I clearly stated what ECU I have in both threads and no one answered my question. I posted the pinouts for Arron who was not sure if pins are the same between a 3S 98-99 Turbo and NA ECU. You directed my posts to buy your harness and nothing else would work!!! I would still need a harness since my car is a 95 TT. I don't have the answers but I know enough when someone is not answering my questions.
He did answer your questions, and he answered them fully. He may have a little attitude, but that's because you come off like you want the keys to all the stuff he's been working on for free. (And seriously, a common knowledge Stealth316 link? You're insinuating that they don't know what they are doing, which is pretty harsh considering what they will be bringing to our platform, and the level of experience of the parties involved.)
So in short, you now have the answers you asked, straight from the horse's mouth, and you still don't know enough to know when someone is answering your questions.
It's comments from people like you that take the joy out of bringing something new and exciting to this platform.
aaronatstate
11-02-2010, 01:17 AM
this made my night. Sorry aaron, i'm a jerk :d
:p :p
marshallh
11-02-2010, 02:17 AM
cool. now I just need to get a VR4 to join the ECU modding party ;)
Also if Jeff ever reads this, let me know if you need help fabbing a pcb and whatnot for the FPGA board for older ECUs.
prop7459
11-02-2010, 02:33 AM
He did answer your questions, and he answered them fully. He may have a little attitude, but that's because you come off like you want the keys to all the stuff he's been working on for free. (And seriously, a common knowledge Stealth316 link? You're insinuating that they don't know what they are doing, which is pretty harsh considering what they will be bringing to our platform, and the level of experience of the parties involved.)
So in short, you now have the answers you asked, straight from the horse's mouth, and you still don't know enough to know when someone is answering your questions.
It's comments from people like you that take the joy out of bringing something new and exciting to this platform.
The only reason I posted the stealth316 to confirm the differences between these ECU's. My intentions were not to insulate them. I do apologize if I came off like that. Also, I am not asking them to post how to mod the ECU to make it work like some else did. People like me do not want to overpay for a product that exist already for my application.
terrets
11-02-2010, 05:29 AM
Uhhh . . . in a nut shell . . . No! Information on how to modify the ECU will not be given out. Sorry. See prior post http://www.3sgto.org/showthread.php?1820-99-Montero-ECU-92-Stealth-TT&p=33139&viewfull=1#post33139
Once Again . . . Harness Adapter (retail available soon in time for X-Mass), Custom MODIFIED ECU (you supply per our part number or we supply), Tactrix OpenPort 2.0 (ONLY the 2.0 will work for programming), EVOScan v2.7 (FOR DATALOGGING), ECUFlash (For PROGRAMMING).
Total price will still be way less than retail for an AEM EMS Series 2 ($1,260.00) plus $$$$ for install and $$$$ for tuning!
AND
Priced under retail for a Greddy e-Manage Ultimate ($680.00) with a 3 Gen boom harness ($269.00)
Now I know you can find it cheaper on eBay, your cousin's uncle, or the guy down the street . . . so then go that route. I refer back to the prior post in reference to why it is the way it is.
Ok thanks for the info. No need to be sorry. I completely understand :).
My only problem is that I already have an EMU.....No one wants to buy it either >_< So. I dont know what I am going to do. I have all winter to figure it out so thats good.
Do you guys expect this to be ready by March/April??
aaronatstate
11-02-2010, 10:42 AM
Ok thanks for the info. No need to be sorry. I completely understand :).
My only problem is that I already have an EMU.....No one wants to buy it either >_< So. I dont know what I am going to do. I have all winter to figure it out so thats good.
Do you guys expect this to be ready by March/April??
Plan is by Christmas if everything if all goes well.
95gto
11-02-2010, 11:00 AM
The only reason I posted the stealth316 to confirm the differences between these ECU's. My intentions were not to insulate them. I do apologize if I came off like that. Also, I am not asking them to post how to mod the ECU to make it work like some else did. People like me do not want to overpay for a product that exist already for my application.
So what pre-existing product are you referring to? Do you mean the ecu or the harness? The 99 ecu's are more expensive due to rarity, so just developing a solution for them is not the way to go. There just aren't enough to go around and they cost too much. So yes the ecu's are there, but are not a viable option. But if you already have one I'm sure Brett or Jeff could work out a solution for you. As for the harnesses, Boomslang only offers harness extension for our cars that come with pre-wired plugs for piggy back controllers, and these harnesses are not that.
Everyone needs to take a step back, take a deep breath, and then come to terms with the fact that this tuning solution has been thoroughly reviewed for the best/most cost effective solution, and that solution will be the one that is offered. The information to make these mods will not be openly published due to a number of reasons but in the end does it really matter? This will be a fully tunable solution for much less than the cost of an AEM, which is the only other tuning solution for these cars that will offer similar performance.
donniekak
11-02-2010, 11:48 AM
Is this going to be a hardware only solution? Or, will a fully featured definition file be provided? How will the definition be distributed? ECMlink distributes their program for free, and only charge for the hardware. This makes it much easier for people to get a look at what they are buying.
aaronatstate
11-02-2010, 12:42 PM
Is this going to be a hardware only solution? Or, will a fully featured definition file be provided? How will the definition be distributed? ECMlink distributes their program for free, and only charge for the hardware. This makes it much easier for people to get a look at what they are buying.
The ROM and XML files for ECUFlash are already out there :)
mh3kgt
11-02-2010, 01:01 PM
Sounds awesome. Good work!
To keep this half on track for the flashing stuff, I'll spell this out as best as I can. Let's pretend your 3000GT is an "A" and a montero is a "M":
Boomslang = Pass-through harness. Pin 1 goes to pin 1, pin 2 to pin 2, etc. It DOES NOT do anything except give you somewhere to splice wires into an intermediate harness, that is side "A1" to side "A2".
Adapter Harness = CONVERTS/adapts the "A" connectors to the "M" connectors so that you can plug it into the new ECU and go, without sitting on the driver's side floor, decoding pin-out diagrams, with some hacked up junkyard connectors, soldering them into your main harness. You CANNOT just plug your 3S harness into the other ECU ... it doesn't work. You NEED the adapter harness, OR if you MUST go the cheap route; find some junkyard connectors. Cut off your main connectors. Figure out the pin-out, and solder everything in the car. Then find the flash enable port and hook that up. And the OBDII port if you don't have it. Do it once, and I guarantee, you'll gladly spend the money on the harness; unless you're a masochist.
People have money spent on a variety of ECUs to find out which ones work, which ones don't, and the bits in-between. I contributed an ECU for research, too. These guys are doing hard work, spending their time and their money, and it should NOT be given away for free. Be happy that these flashable ECUs are even going to be offered; they could just keep them for themselves and let everyone keep running piggybacks or $2k AEM setups. ;)
Give them some time to get things properly prepared. It's not a shop; it's a few guys doing something for a platform they enjoy, outside of their day jobs. Look at the resources that ECM link has, and yet they STILL haven't even shown a prototype of anything, over a year later, and have nothing but "it's coming. sometime." answers.
This is real. This is proven. This will happen. This would make a great Christmas present. :D
Chris@Rvengeperformance
11-02-2010, 03:18 PM
I would not mind getting involved in testing and I have quite a bit of experience with the emanage blue, SAFC, and logging.
AshyBone
11-02-2010, 04:24 PM
glad this is here now. Get to read more info... After class at least.
CoopKill
11-02-2010, 09:23 PM
All I can say is thank you Sirs! I am sure you have solved which route I am taking for engine management.
terrets
11-05-2010, 05:38 PM
Hey guys can you answer quick. Im working on getting my EMU sold and have a buyer. But I need to know if I can run an open BOV with this setup??? And also can I run a MAP sensor or am I going to need a MAF? Im assuming I need a MAF. :( Because my setup right now does not have any intake, just an air filter directly on the turbo......Im going to need to be running 1000cc injectors as a side note.
Would it be possible to alter the 99 code to allow for a MAP instead of a MAF? I should have stayed in software engineering :(. What was I thinking when I wasnt doing homework and studying....
Thanks.
Greg E
11-05-2010, 06:31 PM
Hey guys can you answer quick. Im working on getting my EMU sold and have a buyer. But I need to know if I can run an open BOV with this setup??? And also can I run a MAP sensor or am I going to need a MAF? Im assuming I need a MAF. :( Because my setup right now does not have any intake, just an air filter directly on the turbo......Im going to need to be running 1000cc injectors as a side note.
Would it be possible to alter the 99 code to allow for a MAP instead of a MAF? I should have stayed in software engineering :(. What was I thinking when I wasnt doing homework and studying....
Thanks.
At this time you need a MAF. Brett wants to go the speed density setup, but there's a few issues with that. One mainly is memory space...
terrets
11-06-2010, 03:21 AM
Ugh. Well then I think I am going to keep my EMU until you guys get it figured out...
Cant you add memory? :p
Polygon
11-06-2010, 02:48 PM
First off, thanks for all the work you guys have done so far. I haven't been too sure about what I was going to do to manage everything. It was pretty much going to be standalone. Well, this gives me another option. Now, I want something that is completely transparent. I want the car to work as if it came from the factory when I'm done. There are just a few things I'd like to know.
1. Are these going to come as complete kits? Is everything we need to get them running going to be included, or do we have to piece it all together? Get the ECU from you, a harness from someone else, etc?
2. Will you give us a complete list of what ISN'T going to work when switching over to this? I don't mind losing things like the boost control and gauge and the active exhaust. But I want to have an idea of everything that I would lose. And perhaps what I would need to do about if anything.
3. Will these come with documentation on some basics on how to tune them?
aaronatstate
11-07-2010, 12:36 PM
Hey guys can you answer quick. Im working on getting my EMU sold and have a buyer. But I need to know if I can run an open BOV with this setup??? And also can I run a MAP sensor or am I going to need a MAF? Im assuming I need a MAF. :( Because my setup right now does not have any intake, just an air filter directly on the turbo......Im going to need to be running 1000cc injectors as a side note.
Would it be possible to alter the 99 code to allow for a MAP instead of a MAF? I should have stayed in software engineering :(. What was I thinking when I wasnt doing homework and studying....
Thanks.
I have an open BOV on my car.
First off, thanks for all the work you guys have done so far. I haven't been too sure about what I was going to do to manage everything. It was pretty much going to be standalone. Well, this gives me another option. Now, I want something that is completely transparent. I want the car to work as if it came from the factory when I'm done. There are just a few things I'd like to know.
1. Are these going to come as complete kits? Is everything we need to get them running going to be included, or do we have to piece it all together? Get the ECU from you, a harness from someone else, etc?
2. Will you give us a complete list of what ISN'T going to work when switching over to this? I don't mind losing things like the boost control and gauge and the active exhaust. But I want to have an idea of everything that I would lose. And perhaps what I would need to do about if anything.
3. Will these come with documentation on some basics on how to tune them?
As far as I understand it, the ECUs can be modified by adding the correct parts to make most (if not all) of that stuff work. Since I dont have any of that stuff, I only bothered with the knock sensor circuit, because that is vital.
Polygon
11-07-2010, 02:15 PM
As far as I understand it, the ECUs can be modified by adding the correct parts to make most (if not all) of that stuff work. Since I dont have any of that stuff, I only bothered with the knock sensor circuit, because that is vital.
Well, I gathered that from reading previous posts. However, I was wondering that if we buy this from you will you guys include the list of everything that we would lose and perhaps a guide of what resistors to put where to get them back if we want them? Chances are I won't have to worry, but I want to be sure.
Also, what about the other two.
terrets
11-07-2010, 08:43 PM
Well Im probably still out of the idea since I couldnt run speed density. Now if you guys figure that shizz out by spring I might jump on this.
aaronatstate
11-07-2010, 09:30 PM
Well, I gathered that from reading previous posts. However, I was wondering that if we buy this from you will you guys include the list of everything that we would lose and perhaps a guide of what resistors to put where to get them back if we want them? Chances are I won't have to worry, but I want to be sure.
Also, what about the other two.
I believe the plan at this point is to hook everything up, so it'd be like a stock VR4 ECU.
95gto
11-08-2010, 02:32 PM
Ugh. Well then I think I am going to keep my EMU until you guys get it figured out...
Cant you add memory? :p
Unless you want to revert back to a maf setup you will want to hold off until the development is further along before you switch over. And as far as I know adding memory is not an option.
First off, thanks for all the work you guys have done so far. I haven't been too sure about what I was going to do to manage everything. It was pretty much going to be standalone. Well, this gives me another option. Now, I want something that is completely transparent. I want the car to work as if it came from the factory when I'm done. There are just a few things I'd like to know.
1. Are these going to come as complete kits? Is everything we need to get them running going to be included, or do we have to piece it all together? Get the ECU from you, a harness from someone else, etc?
2. Will you give us a complete list of what ISN'T going to work when switching over to this? I don't mind losing things like the boost control and gauge and the active exhaust. But I want to have an idea of everything that I would lose. And perhaps what I would need to do about if anything.
3. Will these come with documentation on some basics on how to tune them?
The details are being worked out but as I understand it today the harnesses and ecu's will be offered via a single source. So you would purchase your harness and your ecu through this one location. The ecu's would come pre-altered and pre-flashed. All necessary documentation for required wiring changes would be included, like a fuel pump hot wire or any other change of that type. I know the guys working on the hardware changes are trying to develop a plug and play type solution so they will try to keep any wiring changes on the car to a minimum.
Information on sourcing the parts the any required wiring alterations will be posted once the specifics become more clear.
donniekak
11-08-2010, 04:51 PM
Just picked myself up a 99 montero ecu today. My car won't be together for a few months, but i'm looking forward to running this ecu.
Polygon
11-08-2010, 07:53 PM
I believe the plan at this point is to hook everything up, so it'd be like a stock VR4 ECU.
The details are being worked out but as I understand it today the harnesses and ecu's will be offered via a single source. So you would purchase your harness and your ecu through this one location. The ecu's would come pre-altered and pre-flashed. All necessary documentation for required wiring changes would be included, like a fuel pump hot wire or any other change of that type. I know the guys working on the hardware changes are trying to develop a plug and play type solution so they will try to keep any wiring changes on the car to a minimum.
Information on sourcing the parts the any required wiring alterations will be posted once the specifics become more clear.
Alright, this is sounding pretty promising. I can't wait to see the finished product.
95gto
11-09-2010, 12:45 PM
Just picked myself up a 99 montero ecu today. My car won't be together for a few months, but i'm looking forward to running this ecu.
Guys we don't want you buying parts that can't be used, don't go out and buy anything yet.
All the details of the product launch are still in discussion. How to handle customer supplied ecu's is a topic that has to be discussed and decided upon along with many other things. So the easiest way to avoid people buying stuff they can't use is to have everyone wait. I know waiting sucks but so does buying something you can't use.
donniekak
11-09-2010, 01:43 PM
Guys we don't want you buying parts that can't be used, don't go out and buy anything yet.
All the details of the product launch are still in discussion. How to handle customer supplied ecu's is a topic that has to be discussed and decided upon along with many other things. So the easiest way to avoid people buying stuff they can't use is to have everyone wait. I know waiting sucks but so does buying something you can't use.
I'm in the process of modifying the ecu, and building a harness. I have been modifying about 5 different mitsubishi ecu's into dsm turbo eprom ecu's for years.
aaronatstate
11-09-2010, 10:26 PM
I'm in the process of modifying the ecu, and building a harness. I have been modifying about 5 different mitsubishi ecu's into dsm turbo eprom ecu's for years.
So is that the same one you have up for sale on 3SI? Just curious.
Cause if it is, this thread will be gone.
donniekak
11-10-2010, 12:02 AM
Monopoly is never a good business model. No proprietary info was stolen, and it's not like you guy's are trying to share info. I have been tuning ecu's with custom hex code for a long time, and offer to teach people how to do it on their own, if they are willing to learn. Take down the thread, and i will start my own. With how to's, and open discussions.
aaronatstate
11-10-2010, 12:31 AM
Monopoly is never a good business model. No proprietary info was stolen, and it's not like you guy's are trying to share info. I have been tuning ecu's with custom hex code for a long time, and offer to teach people how to do it on their own, if they are willing to learn. Take down the thread, and i will start my own. With how to's, and open discussions.
Must be so good at it, since all the time you've been involved with 3/S you've got how many running with an ECU from a different vehicle?
DSM and 3/S's while related have virtually nothing in common when it comes to the ECU, except they use the same style connectors.
And all the 3S code is out there already, people can do with it what they please.
Don't come in here and pretend to be some saint saying I teach people blah blah. If thats the case why are you trying to sell a Montero ECU for well over double what they go for on eBay? And why don't you go ahead and post the info that needs to be known to make these ECUs work, since you seem to know what it is, and are so willing to share, and teach people.
donniekak
11-10-2010, 12:43 AM
I'm sure that the friendly attitude you guys radiate in this thread, and the other thread on 3si, will draw plenty of customers.
dbest671
11-10-2010, 12:54 AM
I'm sure that the friendly attitude you guys radiate in this thread, and the other thread on 3si, will draw plenty of customers.
And ripping off the community by charging double the norm is "friendly"? See I can say that over here... And then trying to sell it because of possible development that is still in the key word here "developmental" stages.
aaronatstate
11-10-2010, 01:01 AM
I'm sure that the friendly attitude you guys radiate in this thread, and the other thread on 3si, will draw plenty of customers.
So where is all this information since you are so willing to share? It seems you know exactly what to modify, so why not get it out there now so everyone can do it themselves? Funny how you've waited this long to share your knowledge of flashable Mitsu ECUs for the 3/S platform. Seems we could have had this 2 years ago when you first joined 3SI...
I think they'll be attracted to a product that works, and is proven. Not to mention from some very long term members of this community.
aaronatstate
11-10-2010, 10:29 AM
I bet there are do it yourselfers out there still waiting for that information on how to do it themself. Where is it?
green-lantern
11-10-2010, 01:54 PM
And ripping off the community by charging double the norm is "friendly"? See I can say that over here... And then trying to sell it because of possible development that is still in the key word here "developmental" stages.
:stupid:
CoopKill
11-10-2010, 02:09 PM
Why such an attack Donnie? Makes no sense at all.
If you are attempting the same thing, why would you attack someone that is attempting as well for the greater good?
dbest671
11-10-2010, 02:22 PM
Why such an attack Donnie? Makes no sense at all.
If you are attempting the same thing, why would you attack someone that is attempting as well for the greater good?
1. because these ECUs can be found a lot cheaper... Price gouging (so he is taken advantage of the community based on possible development)
2. He is selling it based on the possibility it MIGHT work-- but he doesn't state that in the listing
3. Some poor noob is going to think it WILL work when that has yet to be proven.
So if it doesn't work, he sold somebody an ECU based on the fact that it will work. That is the problem.
I believe it called price gouging based on speculation.
95gto
11-10-2010, 02:36 PM
I'm in the process of modifying the ecu, and building a harness. I have been modifying about 5 different mitsubishi ecu's into dsm turbo eprom ecu's for years.
My applogies, I misunderstood your statement. I read your post as if you intended to send the guys modding the ecu's, Jeff and Brett, your ecu to be modded or that you intended to mod the ecu yourself with information from Jeff and Brett. So my response was pointed such that it would inform both you and other people to not jump the gun and buy stuff for this tuning solution just yet.
If you plan on modding the ecu yourself then go for it. However there is no intention to publish a "how to" or to walk people through the conversion at this time or in the near future. This effort has taken quite of bit time and as such the informaiton will not be given away, especially to those who would be looking to use the information to make a profit. If someone is going to sell the solution for a profit logic would dictate the people that did the work should reap the benefits, not someone looking to make a quick buck on someone else's work.
Monopoly is never a good business model. No proprietary info was stolen, and it's not like you guy's are trying to share info. I have been tuning ecu's with custom hex code for a long time, and offer to teach people how to do it on their own, if they are willing to learn. Take down the thread, and i will start my own. With how to's, and open discussions.
I'm sure that the friendly attitude you guys radiate in this thread, and the other thread on 3si, will draw plenty of customers.
This platform is thirsting for skilled individuals to lead the way with innovation and based on your statements you are more qualified. Since you clearly don't need any help from here you should branch out and start the open discussion and teaching thread you mention, it will be far more valuable than continuing to post in a thread where your motives and credibility have been questioned.
aaronatstate
11-10-2010, 08:51 PM
1. because these ECUs can be found a lot cheaper... Price gouging (so he is taken advantage of the community based on possible development)
2. He is selling it based on the possibility it MIGHT work-- but he doesn't state that in the listing
3. Some poor noob is going to think it WILL work when that has yet to be proven.
So if it doesn't work, he sold somebody an ECU based on the fact that it will work. That is the problem.
I believe it called price gouging based on speculation.
Actually it is proven. My car has been running on a modified 99 Montero ECU, with 99VR4 code, flashed for 450cc injectors, 13t's at 14-14.5psi, with no knock on 91 octane for over 5 weeks now. On my recent trip to dallas I got 25mpg.
But the ECU has to be modified, and modified correctly in order to work.
Actually it is proven. My car has been running on a modified 99 Montero ECU, with 99VR4 code, flashed for 450cc injectors, 13t's at 14-14.5psi, with no knock on 91 octane for over 5 weeks now. On my recent trip to dallas I got 25mpg.
But the ECU has to be modified, and modified correctly in order to work.
This is the key, and those instructions and parts are not, and highly likely will not be, public.
For the people who don't want to be ripped off, and will pay a little bit to support the time, effort, and research financing that people have put into this ... Aaron, 99 VR4 and Gatecrasher will have a solution in the semi-near future. That is, unless antics like this buying-and-price-screwing continues; if that's the case, you can probably bank that they'll shut it all down and keep the parts and information to themselves.
Unless the master and savior "donniekak" releases all of this prized info that he seems to be the only one on earth that knows it. Of course, considering he's charging $250 for an ECU that is under $99 shipped ... prepare to pay as much for his "solution" as you do for an AEM.
dbest671
11-11-2010, 08:50 PM
Actually it is proven. My car has been running on a modified 99 Montero ECU, with 99VR4 code, flashed for 450cc injectors, 13t's at 14-14.5psi, with no knock on 91 octane for over 5 weeks now. On my recent trip to dallas I got 25mpg.
But the ECU has to be modified, and modified correctly in order to work.
Well, I stand corrected:Doh:.
But the information to properly modify the ECU to work is not out in public correct?
So the link he used to sell his ECU was based on development, at least that was my understanding.
So basically who ever bought the ECU will not be able to correctly modify it using the thread he linked in his ad.
aaronatstate
11-11-2010, 10:06 PM
Well, I stand corrected:Doh:.
But the information to properly modify the ECU to work is not out in public correct?
So the link he used to sell his ECU was based on development, at least that was my understanding.
So basically who ever bought the ECU will not be able to correctly modify it using the thread he linked in his ad.
Correct, the info on what needs to be modified is not public. He bought a Montero ECU, then tried to turn it for a profit based on what we are doing.
eljefefx
11-11-2010, 10:23 PM
Correct, the info on what needs to be modified is not public. He bought a Montero ECU, then tried to turn it for a profit based on what we are doing.
Which is pretty fucked up. Might as well change his name to Venik.
J. Fast
11-11-2010, 10:59 PM
When I read the "what you do for a living" thread I discovered there's a lot of brilliant people in this community. Sounds like some bright minds are working hard on this one. It's good to see them team together and build amazing things. What I'm hearing is it's a promising tuning solution with a lot of compromises.
Next year is going to be pretty cool as we'll hit the 20 year anniversary and a number of emerging tech and new platform ideas will be unveiled. Keep up the hard work guys.
Need_a_Miracle
11-20-2010, 10:17 AM
Way cool that there may be other options on the horizon. This looks promising.
pantherchams
12-04-2010, 01:53 AM
Any new progress on this? Stoked for the idea of larger injectors and being able to pass CA smog without hiding cords and cables...
Gotta get myself something for christmas!
Ben
hated
12-15-2010, 03:37 AM
almost for got abt this
95gto
12-15-2010, 10:13 AM
This is not dead, its just slowed down some. The people working on it have been busy with other stuff in their lives but development will continue.
Any new progress on this? Stoked for the idea of larger injectors and being able to pass CA smog without hiding cords and cables...
Gotta get myself something for christmas!
Ben
almost for got abt this
Things are slow since DonnieKak isn't releasing his precious information. ;)
aaronatstate
12-16-2010, 08:22 PM
Things are slow since DonnieKak isn't releasing his precious information. ;)
:lol:
I'm still doing testing, mostly cold idle startup testing. Seems to work just as it did when stock, 1500-1800rpm till temp comes up then drops to 1000-1100rpm after warmed up (idle set to 1094 in ECU).
gs1000kat
12-16-2010, 10:14 PM
At this time you need a MAF. Brett wants to go the speed density setup, but there's a few issues with that. One mainly is memory space...
I don't suppose there is any reason this can't be done using a VPC? Set it up and leave it, and use thge ECU tuning to complete it.
Greg E
12-16-2010, 11:32 PM
I don't suppose there is any reason this can't be done using a VPC? Set it up and leave it, and use thge ECU tuning to complete it.
Funny you say that cuz I was beating myself up the other day for selling my ARC2 when my 98 got wrecked a few years ago. Imagine being able to run larger than 720cc injectors with ANY piggy back and full timing control (are you reading this Matt M? ;))! With the limited memory space in the ECU, I think this will be the better avenue to pursue for speed density.
I'd rather we use that little bit of free memory space for larger resolution fuel/timing maps, alternate maps for launch control/stutter box and NLTS.
gs1000kat
12-16-2010, 11:37 PM
I was beating myself up the other day for selling my ARC2 when my 98 got wrecked a few years ago. Imagine being able to run larger than 720cc injectors with ANY piggy back and full timing control (are you reading this Matt M? ;))! With the limited memory space in the ECU, I think this will be the better avenue to pursue for speed density.
I'd rather we use that little bit of free memory space for larger resolution fuel/timing maps, alternate maps for launch control/stutter box and NLTS.
Did you mean to say "withOUT any piggy back"? That's the point of this thread is to eliminate the need for piggy backs, right? just tryihg to clarify.
Greg E
12-17-2010, 06:42 AM
Did you mean to say "withOUT any piggy back"? That's the point of this thread is to eliminate the need for piggy backs, right? just tryihg to clarify.
No I said what I meant. See the advantage of the arc, maft, and vpc is they all eliminate the stock maf and they translate the karman signal for the stock ecu to use those mafs. The drawback is the added timing advance and they're limited to 720s. Having control of the stock ecu would eliminate those disadvantages as you wouldn't really need to use it as a fuel controller.
gs1000kat
12-17-2010, 08:31 AM
OK, Sorry. I guess I'm just not familiar with how the ARC2 works.
prop7459
12-17-2010, 01:49 PM
I don't suppose there is any reason this can't be done using a VPC? Set it up and leave it, and use thge ECU tuning to complete it.
I have a VPC with a 550 chip and was hoping to go this route if possible with my 99 SL ECU.
aaronatstate
12-19-2010, 04:25 PM
Some graphs I made with the EvoScan data, and my timing and fuel maps. Also the timing on the graph represents the true timing when the differences between the different crank sensors is taken into account.
http://i210.photobucket.com/albums/bb53/aaronatstate/Graph.jpg
Fuel Map
http://i210.photobucket.com/albums/bb53/aaronatstate/FuelMap.jpg
Timing Map
http://i210.photobucket.com/albums/bb53/aaronatstate/TimingMap.jpg
hated
12-28-2010, 12:55 AM
I'm jealous
NOMIEZVR4
12-28-2010, 12:06 PM
When is this coming to the market?? I thought by christmas..
aaronatstate
12-29-2010, 02:32 AM
Real life interfered.
pantherchams
12-29-2010, 02:57 AM
Real life interfered.
What does this mean? Should I just bail and buy a CTS-V or is there a chance I can run a stockish ECU without piggyback, 550s, and bigger turbos?
Ben
aaronatstate
12-30-2010, 02:08 AM
What does this mean? Should I just bail and buy a CTS-V or is there a chance I can run a stockish ECU without piggyback, 550s, and bigger turbos?
Ben
Oh it's still going to happen, and happen soon. Just not by Christmas. Don't bail now.
yellowstealth
01-05-2011, 08:18 PM
Any update? I'm curious what the new timeline is looking like.
Thanks!
You have my interest too, so I'm in as long as it comes to market sooner rather than later. Keep up the good work!
aaronatstate
01-08-2011, 01:12 PM
Right now I'm planning on going up to St. Louis in February. I think most all of us who are working on this will be there. We should be able to get a good amount done that weekend. Really its just in the testing phase right now, slowly working out all the bugs. Just hang tight, it is going to happen, and it is going to happen soon.
FluffyCow
01-09-2011, 11:33 PM
Sorry, I'm late to the party here..
Basically, what you're saying, is you'll be selling an ECU that we can flash with a tune we've made ourselves(Or someone who knows wtf they're doing has made, lol), that'll give us stock driveability, on say, a 92 with 550cc injectors and 15G turbos?
aaronatstate
01-10-2011, 03:18 AM
Sorry, I'm late to the party here..
Basically, what you're saying, is you'll be selling an ECU that we can flash with a tune we've made ourselves(Or someone who knows wtf they're doing has made, lol), that'll give us stock driveability, on say, a 92 with 550cc injectors and 15G turbos?
Yes. My car currently has 450s and 13t's at 14.5psi. Runs awesome, no knock, 91 octane, 14 degrees of timing at the top end. I'm putting Evo 560s in next month. You wouldn't know the car had bigger injectors in it unless I told you. Cold days, starts up, idles high till its warm, then drops the idle to the 1093 I have the target idle in the ECU set at.
yellowstealth
01-10-2011, 03:17 PM
Do you have a guesstimate on when this is going to be available?
aaronatstate
01-10-2011, 03:56 PM
Do you have a guesstimate on when this is going to be available?
No, I'm just doing testing, not any of the hardware stuff.
ilian51378
01-11-2011, 10:13 AM
Subscribed!
ChargerX3
01-11-2011, 03:22 PM
Holding my breath...
aaronatstate
01-13-2011, 09:35 PM
Videos in the first post updated with youtube counterparts. :)
Kx1984
01-13-2011, 10:49 PM
drool
aaron thanks for the pm
kx
aaronatstate
01-13-2011, 11:45 PM
drool
aaron thanks for the pm
kx
No problem man.
apickle
01-14-2011, 09:10 PM
Definitely watching this. I was planning on buying an AEM v2 this spring, but if I can get stock ECU manners with AEM-style tuning, I'll definitely pick up a kit :)
aaronatstate
01-14-2011, 11:44 PM
Going to be putting 560s from an Evo in in the next couple of weeks. Going to turn the boost up some more :D Shouldn't have any of the issues associated with evo 560s and piggybacks because the latency can be tuned.
Did you get the 560ccs in yet? If so, how are they working out for you?
bluzvr4
01-27-2011, 11:58 PM
subscibed
aaronatstate
01-29-2011, 12:19 AM
Did you get the 560ccs in yet? If so, how are they working out for you?
Next week I'll be getting them.
mb3000
01-30-2011, 01:34 AM
Subscribed, great job man.
3000GT MR
02-01-2011, 03:26 PM
I havent had the time to look over this with a fine tooth comb. But im assuming this is only good for stock MAF sensors? i guess you could use the bigger evo one. But i dont see how youd be able to run SD. Thanks for your hard work you guys are doing awesome!
aaronatstate
02-09-2011, 11:32 PM
Picked up some Evo injectors today. I know people have had problems cause of the latencies of the evo injectors, but that should be easy to overcome with the Montero ECU.
yellowstealth
02-10-2011, 03:24 PM
Has there been any progress on the hardware side of this? I'm still hoping to be able to purchase an already modified, ready to flash ECU. Hopefully not too far in the distant future. I wouldn't mind being able to buy a pre-made adapter harness either, but I can handle that part on my own. Modifying the circuitboard on an ECU is not within my abilities, much less figuring out what I'd need to modify.
I feel like I remember that one of the things that wouldn't work was active exhaust/active aero. I don't have/need either of those, if it makes any difference at all.
bridge
02-10-2011, 04:25 PM
: popcorn:
Has there been any progress on the hardware side of this? I'm still hoping to be able to purchase an already modified, ready to flash ECU. Hopefully not too far in the distant future. I wouldn't mind being able to buy a pre-made adapter harness either, but I can handle that part on my own. Modifying the circuitboard on an ECU is not within my abilities, much less figuring out what I'd need to modify.
I feel like I remember that one of the things that wouldn't work was active exhaust/active aero. I don't have/need either of those, if it makes any difference at all.
Hotwired fuel pump is one of the things needed, and the stock boost gauge wouldn't work, last I heard, but that was a number of months ago. I don't know if any effort will be put into those, since most people going with a flashable ECU would already have the FP hotwired and an aftermarket boost gauge.
aaronatstate
02-10-2011, 04:52 PM
Hotwired fuel pump is one of the things needed, and the stock boost gauge wouldn't work, last I heard, but that was a number of months ago. I don't know if any effort will be put into those, since most people going with a flashable ECU would already have the FP hotwired and an aftermarket boost gauge.
This is not true. The fuel pump does NOT need to be hotwired. Vira's car runs just fine with a 99 Montero ECU and adapter harness, without a hotwired fuel pump. IIRC the hotwired fuel pump thing came up from the later single chip ECUs that combine the TCU and ECU chip into one. Jeff can elaborate more, but I know the fuel pump does not need to be hot wired.
Active Aero should work, because I dont think there is any hardware in the ECU that deals with active aero since it has its own computer. Active exhaust is missing components so it wouldn't work, along with the stock boost gauge and a few other things like stock boost control.
This is not true. The fuel pump does NOT need to be hotwired. Vira's car runs just fine with a 99 Montero ECU and adapter harness, without a hotwired fuel pump. IIRC the hotwired fuel pump thing came up from the later single chip ECUs that combine the TCU and ECU chip into one. Jeff can elaborate more, but I know the fuel pump does not need to be hot wired.
Active Aero should work, because I dont think there is any hardware in the ECU that deals with active aero since it has its own computer. Active exhaust is missing components so it wouldn't work, along with the stock boost gauge and a few other things like stock boost control.
Oh, excellent, I hadn't heard about it running without a hotwired pump. I may move this up on my list, since I've got the 98 montero ECU waiting to be modded, but don't have an AFPR yet to do the fuel pump hotwire and it's too cold to be running wiring from battery to trunk in the snow, and I was going to replace the pump while I was back there.
Jeff is doing a FANTASTIC job on all of this.
yellowstealth
02-10-2011, 05:45 PM
Thanks for the info. I doubt too many people are going to be concerned with losing the stock boost solenoid / boost gauge. For me, I removed the solenoid years ago, and if the stock boost gauge stopped working tomorrow I probably wouldn't even realize it. I can't remember the last time I looked at that gauge.
I'm not sure if you're willing to tell us (and understand if you're not), but I'm just curious what modifications need to be made to the montero ECU to get it to work?
Greg E
02-11-2011, 10:53 AM
Oh, excellent, I hadn't heard about it running without a hotwired pump. I may move this up on my list, since I've got the 98 montero ECU waiting to be modded, but don't have an AFPR yet to do the fuel pump hotwire and it's too cold to be running wiring from battery to trunk in the snow, and I was going to replace the pump while I was back there.
Jeff is doing a FANTASTIC job on all of this.
It'll run w/o a hotwired pump but the relay will never switch to lower the voltage. Nothing really to be concerned about.
aaronatstate
02-18-2011, 08:19 PM
560s got here tonight, will be installing tomorrow morning, then going out to do some runs at current boost, then its time to turn it up.
aaronatstate
02-19-2011, 12:13 PM
Installed the Evo 560s this morning. Flashed the ECU and the car started and idled like it was stock.
Went out and did an initial test drive at the same 14-14.5psi I had it set at. Only thing that changed between the logs, like I expected, was the IDC. It dropped 20%. The AFR and everything else was nearly identical. :) Here are some videos.
First Start
http://www.youtube.com/watch?v=PWP2b-ZWxn0
After initial test drive.
http://www.youtube.com/watch?v=NORPCq7HyBA
CoopKill
02-19-2011, 01:03 PM
Still keepin the faith!
Ready for you in july after NG.
__________________________________________________ ____________________
Tapatalk Bitches! :transform:
familyMAN
02-19-2011, 01:06 PM
So when is this going to be available to the rest of us, instead of being tormented and teased with your results? :)
aaronatstate
02-19-2011, 01:39 PM
I'm not sure, I wasn't doing the hardware side, Brett was. I know he's going through a lot of crap right now, and this got moved to the back burner for him, but he's still working on it.
I got my car tuned at 18psi, and its quite fun now :D
aaronatstate
02-20-2011, 11:12 AM
Set the car to 18psi now. I have to play around with my Profec some, cause it was only holding 16.5psi to redline. I'm not sure if its the EBC or possibly the wastegates getting blown open. I'm going to play around some more, then try to adjust the wastegates if I determine its them. I know you can adjust the end, to effectively make the rod shorter.
vyper1
02-20-2011, 04:27 PM
so what is the power limit of the ecu curently? me and a friend been toying with the idea of doing the swap on my car and share info with u guys and test which ever ideas youd have also, we are not to far from you guys (just across the river in windsor) car is a 94 19t turbos 550s (hoping for 680s in spring) arc2 with huge maf and the ebc/ datalogger he made. if theres anything we could do to help please let me know. i was under the impression that you could not go over the stock maf limitations. sorry if i come off kind wierd or speach off not very good at writing out my thoughts
Greg E
02-20-2011, 06:32 PM
so what is the power limit of the ecu curently? me and a friend been toying with the idea of doing the swap on my car and share info with u guys and test which ever ideas youd have also, we are not to far from you guys (just across the river in windsor) car is a 94 19t turbos 550s (hoping for 680s in spring) arc2 with huge maf and the ebc/ datalogger he made. if theres anything we could do to help please let me know. i was under the impression that you could not go over the stock maf limitations. sorry if i come off kind wierd or speach off not very good at writing out my thoughts
The current limitation isn't the ECU. It's the stock MAF. That can be over come with an EVO 8 or 9 MAF though. I know mellon has run 700+awhp with that MAF.
familyMAN
02-20-2011, 09:00 PM
Hopefully this is out before I get my car going again this summer. Hate to compromise with piggybacks or spend the coin on AEM if this will be done in the next 3-6 months.
aaronatstate
02-20-2011, 09:53 PM
I've got 13t's at 18psi, and Evo560s. Should be good for ~400-420whp. I think its still in the cards that all of us are going to meet up in St. Louis at Von's place to prove the swapable ECU.
Greg E
02-20-2011, 10:05 PM
I've got 13t's at 18psi, and Evo560s. Should be good for ~400-420whp. I think its still in the cards that all of us are going to meet up in St. Louis at Von's place to prove the swapable ECU.
It's really tempting to rack up $2500 on my credit card for a set of DR650 billets for my 99 and show everyone the stock ECU is just as good as AEM.
familyMAN
02-20-2011, 10:12 PM
It's really tempting to rack up $2500 on my credit card for a set of DR650 billets for my 99 and show everyone the stock ECU is just as good as AEM.
I think everyone knows that a flashable 99 can be as good as an aftermarket standalone. It's just that most of us don't have flashable ecu's.:rolleyes3:
Greg E
02-20-2011, 10:17 PM
I think everyone knows that a flashable 99 can be as good as an aftermarket standalone. It's just that most of us don't have flashable ecu's.:rolleyes3:
So go out and buy one then... :awesome:
aaronatstate
02-20-2011, 11:21 PM
Here are the graphs from my latest 560 run at 18psi. My boost is def falling off to 16psi at redline, I'm already searching for some WRX actuators with 9psi springs so I can transplant those and take care of the problem.
Anyway, graphs and maps.
http://i210.photobucket.com/albums/bb53/aaronatstate/560s18psigraph.jpg
Fuel
http://i210.photobucket.com/albums/bb53/aaronatstate/560s18psiFuelMap.jpg
Timing
http://i210.photobucket.com/albums/bb53/aaronatstate/560s18psiTimingMap.jpg
familyMAN
02-21-2011, 02:48 AM
So go out and buy one then... :awesome:
What??? They aren't available yet. Unless you have an extra 99 ecu laying around.
Greg E
02-21-2011, 06:33 AM
What??? They aren't available yet. Unless you have an extra 99 ecu laying around.
I do not.
...but this gentleman does.
3si.org/forum/members/49740.html
It's really tempting to rack up $2500 on my credit card for a set of DR650 billets for my 99 and show everyone the stock ECU is just as good as AEM.
One of my best friends is running roughly 550awhp on a stock evo MAF, and hasn't hit near the limit. As mentioned, Mellon pushes ~700awhp on it. Worst case, evo MAF swap, adjust the MAF table in the ECU, done, run.
If my TD05 Evo3 kit doesn't sell by the time I'm ready to drop the motor in my red spyder, and my black spyder has sold, I might just install the Evo3 setup and put the flashable ECU in too. And run a stock MAF. I think ~500-550 awhp on pump gas should prove it capable. Or you can buy my Evo3 TD05 kit for $2k and save yourself that $500 on the credit card :lol:.
Greg E
02-22-2011, 09:20 PM
If my TD05 Evo3 kit doesn't sell by the time I'm ready to drop the motor in my red spyder, and my black spyder has sold, I might just install the Evo3 setup and put the flashable ECU in too. And run a stock MAF. I think ~500-550 awhp on pump gas should prove it capable. Or you can buy my Evo3 TD05 kit for $2k and save yourself that $500 on the credit card :lol:.
:lol:
Naw, I want a true bolt in turbo. Matt M gave me a great offer on a set of the new billet DR650s out of the blue today. I have a whole slew of stuff sitting in my garage waiting for me to install it. I literally have all the supporting mods (including an EVO MAF), just no turbos. Very very tempting...
familyMAN
02-22-2011, 11:17 PM
Was that offer just for you? Care to share:) Billet 650s are on my short list of turbo options for my upcoming build.
aaronatstate
02-23-2011, 12:21 PM
Im still not sure what the limit of the stock MAF is. There are just a handful of people who have the stock MAF without a piggyback. I'd like to (and plan to) get on a dyno to see exactly what a "stock" setup is capable of. Yes the Evo swap is easy in terms of the ECU side, but the MAF is physically different and takes some modifications to fit in the stock setup, inlcluding the plug as well.
Greg E
02-23-2011, 04:48 PM
Im still not sure what the limit of the stock MAF is. There are just a handful of people who have the stock MAF without a piggyback. I'd like to (and plan to) get on a dyno to see exactly what a "stock" setup is capable of. Yes the Evo swap is easy in terms of the ECU side, but the MAF is physically different and takes some modifications to fit in the stock setup, inlcluding the plug as well.
Was just taking to BoyAlan yesterday about this. He's been tuning a few cars lately that have been running into MAF overrun. I asked him to dyno one of those cars so we can get a good picture of what that limit is. It looks to be in the 400-450hp range but I asked for something more factual.
BTW I did come up with a good solution to fit the maf inside our intake bubble. Give me a shout tonight and I'll send you a picture of it. I can even make you one if you want to try it out.
GTOJOE
02-23-2011, 07:15 PM
I thought the EVO MAF fit inside the bubble? except it was round instead of oval but cus the bubble is rubber it fits fine. Or am I thinking of a different MAF?
Greg E
02-23-2011, 07:33 PM
I thought the EVO MAF fit inside the bubble? except it was round instead of oval but cus the bubble is rubber it fits fine. Or am I thinking of a different MAF?
The EVO MAF is approx 3" in diameter. The intake bubble just doesn't "squish" down enough onto it to fit well enough.
vyper1
02-23-2011, 07:46 PM
so if you can set the ecu maf signal could you not use basicly any maf? long as you have all the info of the maf?
Greg E
02-23-2011, 07:53 PM
so if you can set the ecu maf signal could you not use basicly any maf? long as you have all the info of the maf?
There's only 2 devices that I know which send a HZ signal to the ECU using something other than a Karman Vortex MAF and that's the MAFT and ARC2. I don't know of any MAP sensors which send out a pulsating signal which the ECU can use.
aaronatstate
02-23-2011, 10:52 PM
Was just taking to BoyAlan yesterday about this. He's been tuning a few cars lately that have been running into MAF overrun. I asked him to dyno one of those cars so we can get a good picture of what that limit is. It looks to be in the 400-450hp range but I asked for something more factual.
BTW I did come up with a good solution to fit the maf inside our intake bubble. Give me a shout tonight and I'll send you a picture of it. I can even make you one if you want to try it out.
Need to get a Evo MAF first.
aaronatstate
02-26-2011, 10:00 PM
Got a new wideband sensor wire put in today, and now my WB02 is working correctly. I'm pleased to say that under WOT, it reads EXACTLY what I set the AFR in the fuel tables too.
CoopKill
02-26-2011, 10:49 PM
Nice!
Still patient here...
aaronatstate
03-01-2011, 11:43 PM
Like I mentioned on the other thread, there's a calibration screw under the AFM, it's sealed with RTV. Unscew it and the Hz count drops so the ECU thinks you're running at lower load.
Theoretically at least you could upgrade injectors in a car with a non flashable ECU by just recalibrating the AFM and not using a fuel controller, so long as you don't go too big.
This is some of the worst advice I have ever seen/read. The calibration screw is not for tuning. DO NOT ATTEMPT THIS!
aaronatstate
03-01-2011, 11:44 PM
Like I mentioned on the other thread, there's a calibration screw under the AFM, it's sealed with RTV. Unscew it and the Hz count drops so the ECU thinks you're running at lower load.
Theoretically at least you could upgrade injectors in a car with a non flashable ECU by just recalibrating the AFM and not using a fuel controller, so long as you don't go too big.
This is some of the worst advice I have ever seen/read. The calibration screw is not for tuning. DO NOT ATTEMPT THIS!
aaronatstate
03-02-2011, 09:11 AM
So, got the new wastegate springs in, and it didn't solve the problem. Can 13t's not hold more then 16-16.5psi to redline?
Just as a side note, I have DSM SMICs, DNP Hardpipes, Wiseco .015 over 8.3:1 pistons.
Chris@Rvengeperformance
03-02-2011, 10:36 AM
have you shimmed the gates any?
Greg E
03-02-2011, 10:55 AM
So, got the new wastegate springs in, and it didn't solve the problem. Can 13t's not hold more then 16-16.5psi to redline?
Just as a side note, I have DSM SMICs, DNP Hardpipes, Wiseco .015 over 8.3:1 pistons.
Both my Dr500 cars had head work and stock ic & pipes and were able to hold 17ish to the redline. I'd be surprised if 13Ts couldn't do more. (See my post below)
Shoot lawdogg a PM. He ran them for a while on his flat black car.
aaronatstate
03-02-2011, 12:58 PM
have you shimmed the gates any?
No, but I did just put WRX 9psi springs in. I may try to adjust the end piece on the rod to make it tighter.
Both my Dr500 cars had head work and stock ic & pipes and were able to hold 17ish to the redline. I'd be surprised if 13Ts couldn't do more.
Shoot lawdogg a PM. He ran them for a while on his flat black car.
He never ran more then 16psi. Had a spike to 17psi but never more then that.
I've heard that TD04s usually fall off up top by a psi or 2. Mine hold 18psi in any gear like it's their job until 5000-5500rpm and then drop off from there down to 16.5psi.
Greg E
03-02-2011, 01:08 PM
No, but I did just put WRX 9psi springs in. I may try to adjust the end piece on the rod to make it tighter.
He never ran more then 16psi. Had a spike to 17psi but never more then that.
I've heard that TD04s usually fall off up top by a psi or 2. Mine hold 18psi in any gear like it's their job until 5000-5500rpm and then drop off from there down to 16.5psi.
On race gas I had my SSG car spike to 22 and it'd fall to 17. My white car was a consistent 18psi pump gas car. If the boost did fall off I didn't notice. Back then I wasn't really logging boost either so take it for what it's worth.
Aaron, are you still running the profec b spec II (i think)? I had slight taper with that on my evo years ago. The only reliable way I've seen to truly stop taper is by having RPM & PSI based WGDC so that you could force more boost at higher RPM to stop the taper. CANENAC might have some advice, I think he has the 13T record at ~474awhp?
CoreyB
03-02-2011, 04:28 PM
Thats an interesting thought.
aaronatstate
03-02-2011, 07:47 PM
Aaron, are you still running the profec b spec II (i think)? I had slight taper with that on my evo years ago. The only reliable way I've seen to truly stop taper is by having RPM & PSI based WGDC so that you could force more boost at higher RPM to stop the taper. CANENAC might have some advice, I think he has the 13T record at ~474awhp?
Yeah still have the profec b spec II. Well this seems like taper. I bet if I set it to 22psi, it'd drop down to like 19psi at redline. I am going to try and adjust the rods on the wastegate arms to make them a bit shorter, see if that helps. Shouldn't be a problem with that right?
The most effective way of course is to only meter the air to one turbo, that will double the potential power output . The downside is that you'll need to modify the intake pipes, which needs doing anyway.
Steve
Say what?
CoopKill
03-02-2011, 09:13 PM
Say what?
:lmao:
__________________________________________________ ____________________
Tapatalk Bitches! :transform:
Greg E
03-02-2011, 09:27 PM
So what's it for then?
The difference between the N/A AFM and the TT AFM is the calibration.....nothing else (apart from having a different part number).
If your airflow counts are getting all strange at high load it might be because your turbos are begining to surge due to too much boost for the airflow provided......blame the AFM?
Is this a serious question? The calibration screw is to make up for different tolerances each MAF will have to go thru. Turbo cars will need a sensor for higher airflow and stability in higher temps than NA's for example. Since TT's are already equipped with the calibration for the most extreme conditions it was design for, farting around with it isn't going to do much other than sneak unmetered air past it.
As for compressor surge, this is the compressor map for the 13T.
http://www.wallpaperinstaller.com/scooby/13T.jpg
.19 m^3/sec = 403 cfm
Assuming my conversion math is correct, this map shows us that the turbo can support 22psi in the mid range with 20psi to ~ 4700rpms and 16.5psi at about 5700 and then dropping it down to the 13'ish area. Keep in mind this is also for only 1 turbo. Of course this all depends on how much pressure drop your IC has and how efficient it is... Obviously, with 2 turbos, the surge line is still a good ways away.
Now if any of that technical jargon is a miss, let me explain things in another way.
First off, surge in the turbos causes surge in the motor. You will FEEL the motor stumbling and hesitating from the airwalls being generated inside the intake tubes which would fuck with the sensor readings thus mess up your fuel delivery. In Aaron's car (and half a dozen others whom I've been observing) their motors run just fine. The issue is the AFRs just get leaner and leaner.
If that still isn't enough to convince you, let me finally put it to rest by saying that the whacked MAF values in cars with the stock MAF were cured by swapping in an EVO MAF. Magically, these cars had full tuneability returned to them by installing a MAF capable of accurately counting up to 62lbs/min which generally equals to about 600whp.
aaronatstate
03-02-2011, 09:44 PM
So what you are saying Greg is, its perfectly normal for these turbos to fall off to 16.5psi at redline?
Can you show your math?
Greg E
03-02-2011, 09:53 PM
So what you are saying Greg is, its perfectly normal for these turbos to fall off to 16.5psi at redline?
Can you show your math?
Ugh... I'll have to redo it. :lol:
If you want to know how I did it, I just did some CFM to HZ conversions using a conversion factor the DSM guys put together, then converted that to cM/s and plotted those numbers onto the compressor map. The HZ numbers came from a log some guy took on 3si. Your logs would be better suited but I didn't have any with you running these pressures.
I honestly think the only way you're going to get more psi out of your turbos is to quickly close the wastegates once boost starts to taper which isn't possible with your boost controller. You'll need something like what the AVCR (or the stock ecu) does by controlling wastegate duty cycle by rpm. EDIT: To add to this, there's obviously a physical limitation to what the turbo can flow which can't be surpassed with ANY boost controller. Forcing the turbo to keep spinning in this matter may only net you a couple more psi.
The other way is to just run more boost till you get to the point where you reach that physical limit of the turbo.
aaronatstate
03-02-2011, 10:21 PM
Ugh... I'll have to redo it. :lol:
If you want to know how I did it, I just did some CFM to HZ conversions using a conversion factor the DSM guys put together, then converted that to cM/s and plotted those numbers onto the compressor map. The HZ numbers came from a log some guy took on 3si. Your logs would be better suited but I didn't have any with you running these pressures.
I honestly think the only way you're going to get more psi out of your turbos is to quickly close the wastegates once boost starts to taper which isn't possible with your boost controller. You'll need something like what the AVCR (or the stock ecu) does by controlling wastegate duty cycle by rpm. EDIT: To add to this, there's obviously a physical limitation to what the turbo can flow which can't be surpassed with ANY boost controller. Forcing the turbo to keep spinning in this matter may only net you a couple more psi.
The other way is to just run more boost till you get to the point where you reach that physical limit of the turbo.
well I am happy with what I have right now. I mean if we can figure it out sure I'd like to run 18psi to redline, but 16.5 psi on these turbos is dang quick, and it holds 18 to around 5000-5500rpm (not quite sure cause it happens quick :lol:)
Greg E
03-02-2011, 10:27 PM
well I am happy with what I have right now. I mean if we can figure it out sure I'd like to run 18psi to redline, but 16.5 psi on these turbos is dang quick, and it holds 18 to around 5000-5500rpm (not quite sure cause it happens quick :lol:)
Yeah, one of these days I'll figure out how to do the EVOX map sensor swap into our cars... Obviously, you'll need some wireharness mods to work with your ECU but still.
Can I see a couple of your logs? I'm just curious to see what timing numbers you're running at those boost levels on pump.
aaronatstate
03-02-2011, 10:52 PM
12-14 degrees depending on the log. This is the true timing accounting for the sensor latency difference. The ecu is requesting about 3-4 less then that (i.e. the ECU requested 9 and 12 degrees was what was actually going on), then with the latency difference that's what it actually runs (more advanced using a late model ECU on an early crank/cam setup).
Just got off the phone with my mom, about my birthday coming up. Going to be getting and Evo 8/9 MAFS for mah birthday LOL. I win. We'll find out how it works with the Montero ECU in 6-8 weeks. :w00t:
lawdogg
03-03-2011, 12:26 PM
Here are the graphs from my latest 560 run at 18psi. My boost is def falling off to 16psi at redline, I'm already searching for some WRX actuators with 9psi springs so I can transplant those and take care of the problem.
Fuel
http://i210.photobucket.com/albums/bb53/aaronatstate/560s18psiFuelMap.jpg
Timing
http://i210.photobucket.com/albums/bb53/aaronatstate/560s18psiTimingMap.jpg
Aaron: Interesting how they look compared to the OEM maps.
http://stealth316.com/images/maxtimingmap-95spydervr4.gif
http://stealth316.com/images/fuelmap-95spydervr4.gif
Seems like you're running a little more timing before 5000rpm and a little less after, and your target AFRs are (just a little) more lean. I initially thought this was counter-intuitive since I was remembering (incorrectly) that I was running along the 100% load row of both OEM charts ... but what I didn't take into account was that the nature of the SAFC is that the nature of load signal adjustment makes the ECU run along lower-load timing row which is more advanced.
Anyway, thanks for posting your maps. It's an awesome comparison and imo serves as some evidence of the need for timing control when using a piggyback load signal adjuster - whether it's an AFPR, an S-ITC, or an emanage, you'll still need it, as opposed to just this flashable ECU setup.
Considering I sold my SAFC, looking at cost alone, this flashable ECU setup seems more and more reasonable. Anyway I'm still working on a reply to your PM - gears are turning about whether I want to make this jump. :w00t:
Shoot lawdogg a PM. He ran them for a while on his flat black car.
He never ran more then 16psi. Had a spike to 17psi but never more then that..
I thought I'd just poke in and mention that although I never purposefully ran more than 16psi ... there was one time, lol, after I put in my profec-b, where I had hooked up the solenoid incorrectly. Boost spiked somewhere high, problem was my boost gauge only went up to 20psi, and it held it - not to redline - but still for a while. :Doh: :w00t:
aaronatstate
03-07-2011, 09:55 AM
Problem solved, well not solved, but found.
After talking with Grayson he suggested simply that the turbine side was too small, and I was blowing the gates open. He suggested to confirm this, go out, set to WG boost, and let her rip. If the boost climbed with RPM, it would confirm because their is too much exhaust flow. Well he was right (is he ever wrong?), and the problem is known. No easy fix really, except to wire the gates shut, which isn't happening :lol:
Chris@Rvengeperformance
03-07-2011, 10:49 AM
did you shim the gates with washers? I have 3 washers under each of my wastegate bolts.
aaronatstate
03-07-2011, 11:20 AM
did you shim the gates with washers? I have 3 washers under each of my wastegate bolts.
I didn't put any washers anywhere, just adjusted the rod so you had to pull it over to the wastegate flapper.
Do you really think shimming will help? I dont want to mess with being able to actually control the wastegates either.
aaronatstate
03-07-2011, 11:27 AM
Dont forget I just got done installing 9psi springs in my wastegates too. I think with those, and the rod adjusted so you have to pull it over to attach it to the wastegate, shimming isn't going to help much, if at all.
Chris@Rvengeperformance
03-07-2011, 12:10 PM
I didn't put any washers anywhere, just adjusted the rod so you had to pull it over to the wastegate flapper.
Do you really think shimming will help? I dont want to mess with being able to actually control the wastegates either.
It helped tremendously with my spool on my 19ts and 13Ts.
Yes, you lose a little bit of low boost control, but if you want to run less than 15 PSI then it isn't needed anyway.
I didn't have any problem holding boost to redline with my 13Ts.
aaronatstate
03-07-2011, 01:02 PM
It helped tremendously with my spool on my 19ts and 13Ts.
Yes, you lose a little bit of low boost control, but if you want to run less than 15 PSI then it isn't needed anyway.
I didn't have any problem holding boost to redline with my 13Ts.
Spool is not a problem, but I guess I can try shimming them and see what happens. The washers go on the bolts between the wastegate and its mounting point on the turbo right?
Chris@Rvengeperformance
03-07-2011, 01:32 PM
Spool is not a problem, but I guess I can try shimming them and see what happens. The washers go on the bolts between the wastegate and its mounting point on the turbo right?
Yes
Sent from my DROIDX using Tapatalk
yellowstealth
03-14-2011, 12:42 PM
Any updates on the availability of the pre-modified ECU / harness? Any idea of a ballpark price yet?
If I beg, offer beer money, and sign a non-compete contract can I get the info on the missing knock-sensor components so I can mod my own? ;)
aaronatstate
03-14-2011, 12:57 PM
I know boomslang will now make an adapter harness, with the reflash stuff included, if you ask. I think they want 250 bucks for it though. As for the ECUs, I haven't talked with Brett in a long time. I need to get a hold of him first.
yellowstealth
03-14-2011, 10:31 PM
Thanks for the update / info.
Artie
Any updates? My car is out of the shop next week, and a flashable ECU would be cool. How's it working for you still? I need to source an adapter harness + reflash port.
aaronatstate
05-12-2011, 08:22 PM
Any updates? My car is out of the shop next week, and a flashable ECU would be cool. How's it working for you still? I need to source an adapter harness + reflash port.
Still working great. Working on installing the Evo 8 MAF this weekend.
aaronatstate
05-14-2011, 12:34 PM
Got the Evo MAF installed last night.
After getting the ECU flashed with all the Evo values, I started it up, and it ran like crap, almost like the MAF was disconnected. So I reflashed the stock values back in, and it ran pretty normal. Then I just changed the size and scaling, and it ran fine, but WAY lean. So I then decided that, after looking at the scaling values, the stock ones need to be the ones. All of the EVO values are LOWER for a given HZ. I believe this to be due to 2.0L vs 3.0L. So I flashed with just a size change. I only tested at idle, but it ran PERFECT. My belief now, after talking with Jeff, is ONLY the SIZE needs to be adjusted. The other scaling (hz vs g/s) need to remain the same due to the bigger engine (maybe fine tune them over time).
Well just the size didn't do it. I think this MAF adder also needs to be adjusted. The car still ran WAY lean under boost.
After thinking about it more, the values for the scaling need to be close to the stock 3/S levels. Since the Karman sensor calculates Hz based on air velocity, this is going to be very similar across all Mitsu MAFS. So 1600hz is equal xx velocity. However, that velocity equates to a drastically different amount of airflow between a 4 cyl 2.0 and a 6 cyl 3.0.
Changing the size and the MAF adder did it! Car behaves like stock, idles, free revs, and drives like its on the stock MAF. Under boost, 14psi or 18psi the AFRs are rock solid at what I have them set at in the ECU (10.7:1).
Also should note the boost doesn't seem to be dropping off as much anymore either. Though that may be due to the 48 degree temps here today, but I think the Evo MAF helped too.
Jesters Deadd
05-14-2011, 02:01 PM
So, just to understand this better. The EVo maf is smaller but reads higher Hz? So it is an upgrade to the bigger 3s maf...
aaronatstate
05-14-2011, 02:56 PM
So, just to understand this better. The EVo maf is smaller but reads higher Hz? So it is an upgrade to the bigger 3s maf...
Correct. The Evo maf is smaller, but it flows more and has a better and higher resolution. It's good for about 600whp, where as the factory MAF is good for about 400whp. It is most certainly an upgrade for the 3/S.
bboyalan
05-14-2011, 03:27 PM
Hmph, that is odd. I did not encounter any of those problems with the upgrade a while back. At least it is working fine for you now though lol.
-sent from my G2
AWDBoostin
05-14-2011, 03:31 PM
When are these ECU's going to be up for sale?
aaronatstate
05-14-2011, 04:39 PM
Hmph, that is odd. I did not encounter any of those problems with the upgrade a while back. At least it is working fine for you now though lol.
-sent from my G2
Well I think you will have problems. This is the stock code for the Evo and the 3/S. Evo on the left, 3/S on the right. You can see that at any Hz the airflow is more in the 3/S, this is because the 3.0L flows WAY more air then the 2.0L in the Evo. That's why my car ran like absolute shit with the Evo values in. It thought there was WAY less airflow, so it was running incredibly lean.
I would suggest changing the scaling and smoothing tables back to the stock 3/S values, and changing only the size and maf adder values to the Evo values (357.5 for size, 140 for adder). I believe the car will run tremendously better for you.
Hz Airflow Hz Airflow
19 145 0 166.77
25 152 25 166.77
50 165 50 210.656
75 175 75 228.211
101 182 100 238.242
126 187 125 244.512
151 191 150 250.781
176 195 175 255.797
201 198 200 260.812
226 200 225 265.828
252 203 250 269.59
277 206 275 273.352
302 208 300 275.859
403 217 400 284.637
503 222 500 288.398
604 226 600 290.906
805 233 800 294.668
1006 236 1000 293.414
1208 237 1200 293.414
1409 235 1400 290.906
1610 232 1600 289.652
bboyalan
05-14-2011, 05:43 PM
It is something to keep in mind for sure, but we will just wait and see since everything has been fine with both the 550's and 780's. I posted a few logs but do not want to clutter your thread.
aaronatstate
05-14-2011, 07:10 PM
It is something to keep in mind for sure, but we will just wait and see since everything has been fine with both the 550's and 780's. I posted a few logs but do not want to clutter your thread.
I mean you can solve the problem with the fuel tables, but thats not the proper fix. You can just richen everything up, and solve the lean issue, but I'd rather solve the real root cause, then just fix the symptoms :)
aaronatstate
05-15-2011, 02:58 PM
50 miles, no problems. Boost at 18-18.5psi.
Drummer
06-17-2011, 02:33 PM
You guys are doing great work. Keep it up! See you at the meet!
ChargerX3
06-28-2011, 02:14 PM
Running silky smooth on that EVO maf still?
Hey guys,
I need to be able to take a load value from a Mitsu ECU, and work backwards through the MAF measurement algorithm to get raw airflow pulses per crank (or cam) rotation.
Once I get that, I can work forward through the AEM EMS MAF algorithm to generate an AEM Engine Load for that same g/s value.
This will allow me to translate the OEM ECU tables into AEM calibrations directly - I need this for EGR (what I'm working on now) but the intent is to do it with timing and fuel as well. Ideally, I should be able to produce an AEM EMS cal that is exactly identical to the OEM ECU.
If somebody can walk me through the algorithm where the ECU starts with raw MAF pulses and ends up with a value in g/sec, that would be a HUGE HUGE help.
Thanks.
DG
99 vr4
07-17-2011, 06:08 PM
Hey all - I have been hard at work on this as Aaron and Greg can tell you. I have the harnessess available through Von aka xwire (morgans motorsports) . . .
Now for the big shocker. Recently I discovered an issue with the knock control circuitry. And of course I fixed the Diamante Distributor vs. IGN Transistor issue. BTW - This knock sensor issue also extends to the 3000GT SL ecu. So for those of you using Montero ECU's, please be careful of phantom knock and the inability to see real knock.
aaronatstate
07-17-2011, 07:28 PM
The Montero ECU actually just shows like 9 counts all the time. The Diamante and SL are the ones to be careful with.
Jesters Deadd
07-18-2011, 01:35 AM
Hey all - I have been hard at work on this as Aaron and Greg can tell you. I have the harnessess available through Von aka xwire (morgans motorsports) . . .
Now for the big shocker. Recently I discovered an issue with the knock control circuitry. And of course I fixed the Diamante Distributor vs. IGN Transistor issue. BTW - This knock sensor issue also extends to the 3000GT SL ecu. So for those of you using Montero ECU's, please be careful of phantom knock and the inability to see real knock.
Wow this is really great. Then the Diamante ECU will be able to start a car like normal. Its weird that the DiaEcu runs the car like normal after it starts.
I'm about a week away from getting my modded Montero (HUGE thank you Gatecrasher!) installed and tuned. I'll have some before/after numbers and graphs for a BPU 9B car.
NOMIEZVR4
08-23-2011, 02:08 PM
Keep us posted..
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.