View Full Version : Idle Help Please
knights19
03-29-2019, 12:17 PM
I've just started the tuning of my 3000GT engine in my kit car running a Chrome ECU. Starting with the idle setting as recommended in the guide and fell at the first hurdle. With the idle wire connected the base idle is low so I adjust it up to 850 (as set in the ecu) and it runs quite smooth. As soon as I disconnect the wire. idle goes up to 1100rpm. So I figured there must be something wrong with the idle control valve. Took it out and sure enough, pins 4-5 have no resistance. I made sure the valve is fully out and refitted it but left the connector off; still the same problem.
Any ideas folks?
anyonebutme
03-29-2019, 06:14 PM
Engine temp fully warm and a/c off?
RealMcCoy
03-29-2019, 06:18 PM
The ECU primarily uses timing to make rapid idle speed changes. The IAC is used for preprogrammed large changes. until you have a working IAC, I'd just leave it unplugged and turn the BISS in until you get an acceptable warm idle speed. Without the ability to adjust the airflow, I suspect your idle is increasing when it puts the timing back in...
knights19
03-30-2019, 04:59 AM
Yes engine warm and AC off.
Why would it add timing at idle speed though?
I'll try plugging the standard ecu in to see if it still does it.
anyonebutme
03-30-2019, 04:32 PM
Base idle mode locks timing at 5 degrees, while the actual timing at idle is closer to 12. It's a diagnostic mode for certain things, so if you are setting idle speed with the IAC locked you need to set it with the ECU in normal mode.
RealMcCoy
03-30-2019, 04:36 PM
Yes engine warm and AC off.
Why would it add timing at idle speed though?
I'll try plugging the standard ecu in to see if it still does it.
Like I said, the ECU uses timing to control idle speed... When you ground the connector, it fixes the timing and IAC to a set point so you can establish the baseline. When you unplug the connector, and it feeds that timing back into it, and the IAC is unable to move, you get an increased idle speed...
Until you have a working IAC, I'd ignore the set connector, and simply set the warm idle to a livable point in normal operation.
knights19
04-01-2019, 12:28 PM
Seems stable now.
Can you advise on the attached?
I'm getting ignition cut due to knock count but I suspect my base noise is high as the engine is near solid mounted with a Ford gearbox attached and the rear diff mounted to the side of the engine.
Is it a multiplier issue?
9712
9713
9714
RealMcCoy
04-01-2019, 01:08 PM
There have been instances of false knock reported, but it's pretty rare... The factory algorithm is pretty good about picking out what is real knock.
How much timing is being pulled? And what knock sum are you seeing?
knights19
04-01-2019, 01:49 PM
Knock voltage seems low in the data above, is that correct?
I get 8-9 counts but when it starts, it doesn't stop. Even when I cruise afterwards the sum stays up there and the timing stays at 5 degrees as soon as it sees it.
RealMcCoy
04-01-2019, 04:48 PM
Knock voltage seems low in the data above, is that correct?
I get 8-9 counts but when it starts, it doesn't stop. Even when I cruise afterwards the sum stays up there and the timing stays at 5 degrees as soon as it sees it.
I think you have an electrical problem somewhere... 7-9 counts is the default output by the ECU when there is a knock sensor problem. It will not flatline the timing, It puts it into the low octane map. If it's seeing real knock, it only pulls a a small amount of timing per count. 9 counts of real knock is pretty insignificant in the timing map (you can see how much, and modify the number in the knock table)
I wonder if you don't have a short to ground in your timing set connector..?
knights19
04-02-2019, 04:41 AM
Hmm, would make sense.
So there may be a fault with the knock sensor circuit hence the default knock, but where would the fault be to cause a flat line 5 degree timing?
Just found this on another thread so I will look at the knock sensor more:
according to my logs it's more like this:
<5* timing advances
5-7* timing flatlines
8*+ timing retards
knights19
04-02-2019, 05:45 AM
If it were a faulty sensor, I understand it could be intermittent, but at the same point in a third gear pull after 6 logs?
knights19
05-08-2019, 07:32 AM
BTW, you guys were spot on correct, removed the new knock sensor and put the original one back in, problem gone.
Still have a few counts around the 120/140 load at 3500rpm so have been smoothing out the tables as suggested.
Thanks.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.