PDA

View Full Version : putting on timing belt, have couple of questions



a2j
10-18-2010, 08:13 PM
I'm trying to follow manual to put the new timing belt on.
I have removed the camshafts and didn't mark anything on the old belt. also was moving crankshaft back and forth. (I was doing VSS and lifters)

so I realigned cam gears, and set crank sprocket 1 tooth back. but when I install everything and make the belt tight with tensioner pulley, the crankshaft is still 1 tooth behind. what am I doing wrong? :confused:

Steve '92ES
10-18-2010, 08:37 PM
When you tighten up your tensioner pulley make sure you pull any slack up from the bottom, not down from the top. What's happening is that you're pulling the cams off 1/2 a tooth, instead of pulling the crank in a full tooth. It helps to have someone hold the front cam still...

Mean Green
10-18-2010, 08:41 PM
I've always just lined everything up exact and lock the cams in place...that's how I've always done it and never had a problem.

Amphiron
10-18-2010, 08:53 PM
I'm trying to follow manual to put the new timing belt on.
I have removed the camshafts and didn't mark anything on the old belt. also was moving crankshaft back and forth. (I was doing VSS and lifters)

so I realigned cam gears, and set crank sprocket 1 tooth back. but when I install everything and make the belt tight with tensioner pulley, the crankshaft is still 1 tooth behind. what am I doing wrong? :confused:
try compensating by setting it one tooth ahead

a2j
10-18-2010, 08:55 PM
When you tighten up your tensioner pulley make sure you pull any slack up from the bottom, not down from the top. What's happening is that you're pulling the cams off 1/2 a tooth, instead of pulling the crank in a full tooth. It helps to have someone hold the front cam still...

the only slack I ended up with is where tensioner pulley is. and when I tighten it up, nothing else moves. so right now I have no slack, everything is tight and crank shaft is 1 tooth off. I was thinking to do the way Mean Green described. I have no other explanation to what is going on, so far.

a2j
10-18-2010, 08:56 PM
try compensating by setting it one tooth ahead

I'll end up that way at the end. nothing moves when I finishig with tensioner pulley.

Drweldin
10-18-2010, 09:03 PM
yeah, you want to lock the cams and have slack between the front ex cam and the crank....then you tension, and crank rolls clockwise 1 tooth in the process..."usually", lol.

Bluejediz
10-18-2010, 11:15 PM
I've always just lined everything up exact and lock the cams in place...that's how I've always done it and never had a problem.

x2...Thats the way ive done it on every tbelt job ive done. As long as there is NO slack anywhere except where the tensioner is and you spin everything around several times and its still lined up then your golden!

Steve '92ES
10-19-2010, 12:57 AM
the only slack I ended up with is where tensioner pulley is. and when I tighten it up, nothing else moves. so right now I have no slack, everything is tight and crank shaft is 1 tooth off. I was thinking to do the way Mean Green described. I have no other explanation to what is going on, so far.

Try putting the belt back on, following the order given in the manual EXACTLY: start with the front cam, clip the belt on with a binder clip, then the second cam and another clip, around the water pump, etc. I've seen people suggest going backwards, starting with the rear most cam, but it's been my experience that leads to the exact problem you're having. Cam lockers would be handy and there's plenty of home-made ideas around but if you don't have any having someone hold the front cam still can help. If after re-installing the belt you still can't pull the crank into alignment go ahead and put it on the mark and tension it up. If everything stays in alignment after spinning it around a few times, and the pin on the tensioner slides in and out, you're probably good....

TwIzTeD_3kGt
10-19-2010, 01:26 AM
the only slack I ended up with is where tensioner pulley is. and when I tighten it up, nothing else moves. so right now I have no slack, everything is tight and crank shaft is 1 tooth off. I was thinking to do the way Mean Green described. I have no other explanation to what is going on, so far.

That's because you're doing it the right way. When you do it the right way, you don't need to set the crank back a tooth. Just line everything up and leave all the slack in the tensioner area like you did. You'll be fine.

a2j
10-19-2010, 03:53 AM
well, it is my first timing belt change. so I guess I'll do it the right way, align the crank and do it they way I did it before. I'm pretty sure everything will stay aligned. because I tried moving everything several times, while camshafts will be aligned, the crank would be 1 tooth off.

terrets
10-19-2010, 03:58 AM
Just make sure you crank it 3 times. Let it sit an hour, and crank it some more...First timing belts are fun :D. I did my first in Feburary on my vr4.

a2j
10-19-2010, 04:02 AM
and while am at it, I'm doing others things including whats on my current avatar ;) so for now I'm turning the crank by hand.

blindmist
10-19-2010, 04:02 AM
I have timed about 15 6G72's. Start at the crank, pull the belt to the rear exhaust, then intake, then water pump, then front intake, exhaust, and back to the tensioner and crank. Here is the deal with the 1 tooth off on the crank deal. This is to compensate for the movement of the cams when you take the slack out of the belt when you rotate the tensioner over as tight as you can get it. The cams roll back (counter clockwise) just a bit. The slack you are taking up should be from the front cam to the tensioner. Before you even look at anything to see if it is lined up. Do 2 revolutions clockwise on the crank. Then check your crank and you should be spot on. I have slapped timing belts on a 6G72 in 5 mins and been done with it with this method.


Also, on mine, when I was pulling the belt from the crank to the rear exhaust, I would have to pull the cam 1 tooth back to get it on the mark, and the intake 1-2 teeth forward. The front head, both cams are going to want to jump on you. My best advice for this is to take a 17mm wrench and the t-belt that is around the rear cams and water pump. Put the belt on the cam, pull the belt over. Then turn the cam with the wrench and let it pop teeth on the belt until you have it in the correct position, then pull it over and around the front intake cam, and do the same thing. Once you are on all 4 cams, you should be able to push the tbelt onto the tensioner and be able to let it just sit for a second or two. Then proceed with what I stated ^^^^

Also, just to be certain, 1 tooth back on the crank would mean that you are on the tooth just to the right of the timing mark.

All you need to do this is a 17mm for the cams and the socket for the tensioner bolt. None of those stupid clips. I hate those.

terrets
10-19-2010, 04:04 AM
Damn your good....Yes always turn it by hand :D

a2j
10-19-2010, 04:09 AM
my tension is pretty tight. but if I would try to align crank shaft from "1 tooth off" position and move camshafts, wouldn't that make either cams or crank off? the only way I see it working is when I have some slack after rear exhaust cam and crank shaft sprocket. otherwise how do you move it without moving the cams while belt is on ?

Steve '92ES
10-19-2010, 04:09 AM
So blindmist, basically you just do the whole thing backwards? Start at the crank then go back to front and pull any slack down from the cams rather than go front to back and pull slack up from the crank?

blindmist
10-19-2010, 04:12 AM
So blindmist, basically you just do the whole thing backwards? Start at the crank then go back to front and pull any slack down from the cams rather than go front to back and pull slack up from the crank?

Correct. Works every time. The slack should be on the "front" of the belt before rolling the tensioner over with my method. In between the tensioner and front intake cam.

Steve '92ES
10-19-2010, 04:15 AM
the only way I see it working is when I have some slack after rear exhaust cam and crank shaft sprocket
That's exactly correct. If you've got all the slack out don't worry about the one tooth. Just be sure you're not pulling the belt TOO tight while you're putting it on. Pull it enough that the teeth on the belt fall naturally into the cogs, but don't reef on it.

blindmist
10-19-2010, 04:21 AM
Seriously, give my method a shot. It is by far the easiest I have come up with and it has worked on numerous occasions. I should also say, there has been a time where the rear exhaust cam didn't need to be popped 1 tooth when putting the belt on with my method. And if you don't have one of the adapter tools with the 2 prongs for the tensioner pulley, you really aren't doing it right and not getting enough slack out of the belt.

The main thing with my method is, have the crank back 1 tooth, and get all the cams in time with the slack on the front. Then take the slack out by rolling the tensioner clockwise. This will pull the cams off their marks(counter clockwise), but put them in time with the crank. After you have done 2 clockwise revolutions on the crank, set the crank in time this time, and all 4 cams should be in time as well.

The worst part about my method not working for you, is you are still where you started, an untimed engine.

TwIzTeD_3kGt
10-19-2010, 10:32 AM
That's exactly correct. If you've got all the slack out don't worry about the one tooth. Just be sure you're not pulling the belt TOO tight while you're putting it on. Pull it enough that the teeth on the belt fall naturally into the cogs, but don't reef on it.

I doubt anyone can pull hard enough to make the belt fall into a cog it shouldn't be in, or to damage the belt. The only fear I would have from pulling too hard is moving the gears it's already set on. You have a bad experience with that or what?

Sounds like you're routing it with the right amount of tension and leaving the slack in the correct area, but you were using the method for those who don't.

Bluejediz
10-20-2010, 01:45 AM
Just make sure you crank it 3 times. Let it sit an hour, and crank it some more...First timing belts are fun :D. I did my first in Feburary on my vr4.

I wish my first belt was on my stealth. Mine was on the GF's eclipse....talk about added pressure!!!! Not only would I have to deal with screwed up heads but with her aswellhttp://www.smileyvault.com/albums/stock/smiley-scared0011.gif (http://www.smileyvault.com/) Glad it went ok lol

terrets
10-20-2010, 03:16 AM
:lol: Thats good. Did she know it was your first one?!?

Mike-92RT
10-20-2010, 01:19 PM
the way you time your engine, is wrap it around the front camgears first, to the waterpump, to the rear camgears, through the tensioner idle pulley, to the oil pump, to the tensioner pulley. Make sure you pull it tight as you go, make sure theres no slack.

Now for the marking on the oil pump. You don't line it up exactly to TDC, theres still slack in the timing belt. Have it set one tooth back. So when you tighten the tension on the belt, the oil pump will move, and you will be at TDC.

The camgears CAN'T move during the tensioning process!

When you tension the pulley, the 2 holes should be above the bolt roughly. Like this:
http://i581.photobucket.com/albums/ss258/Mike92RT/DSC00089-1.jpg

When you're done tensioning it, check to see if you can slide the grenade pin in and out of the tensioner. Rotate the engine twice, check it again to see if its loose. Leave it for about 15min. Then check again to see if its loose. If it is, then you're golden!! If not, you have to do those steps all over again.

TwIzTeD_3kGt
10-20-2010, 04:17 PM
Am I the only one besides the OP who does this so the crank doesn't move when tensioned? It works on all cars, and is less difficult than trying to guess where the tension is going to move the crank to. Just leave all the slack in the tensioner area, boom done.

Just to add to the above post, if you have the tensioner tool and a torque wrench, you tension it to 7 ft/lbs and then tighten the pulley (which ends up looking like the picture if everything is new). Then you rotate the crank twice and see if the pin moves. If not, do it over because it's not tensioned properly.

blindmist
10-20-2010, 05:01 PM
Am I the only one besides the OP who does this so the crank doesn't move when tensioned? It works on all cars, and is less difficult than trying to guess where the tension is going to move the crank to. Just leave all the slack in the tensioner area, boom done.

Just to add to the above post, if you have the tensioner tool and a torque wrench, you tension it to 7 ft/lbs and then tighten the pulley (which ends up looking like the picture if everything is new). Then you rotate the crank twice and see if the pin moves. If not, do it over because it's not tensioned properly.


This is what I have been trying to say!! Fuck moving the crank when tensioning the belt, that is too hard. Move the damn cam gears the way I say to do it. And guess what, if you start from the crank and go to the back cam and work the way I say to, you don't need any clips, no hassle, its just simple, and easily done. I should have made a video to prove to people how easy it was if you just install the belt "bakwards" from how the manual says to do it.

Mike-92RT
10-20-2010, 06:22 PM
My manual says to leave it a tooth back from TDC.

If you do it right, it'll align at TDC when you tighten the belt to the correct tension. Worked for me 3 times, no problems, and its not even a big hassle.

blindmist
10-20-2010, 06:24 PM
My manual says to leave it a tooth back from TDC.

If you do it right, it'll align at TDC when you tighten the belt to the correct tension. Worked for me 3 times, no problems, and its not even a big hassle.

Where was your slack? From the front exhaust to the tensioner or the back exhaust to the crank? The crank isn't so easy to move when you are 8.5:1 fresh bore and hone brand new engine, let alone NA at 10.5:1 or whatever they are. It is much easier to have the slack on the front of the motor and let the cams roll back (counter clockwise). If you put the belt on starting from the crank going to the rear exhaust, the slack will be on the front of the motor, allowing you to let the cams roll.

If you didn't let the cams move when applying tension, then your slack was on the rear of the motor, not the front, and the crank moved when you applied tension. This can be very difficult if you don't have cam lockers. The cams want to naturally roll back when they are in time, why not let them with the slack on the front of the motor?

BTW, I am agreeing with you on one tooth back. As in the tooth to the right (clockwise) of the timing tooth.


Let me put it like this.

Here is how to time a 6G72. First things first. Set the crank one tooth back. As in the tooth to the right (clockwise) of the timing tooth.

If you route the belt starting from the crank going to the rear cams, the slack should be from the front exhaust to the tensioner.
This is what is important here. When you roll the tensioner to apply tension, the cams need to roll counter-clockwise and the crank SHOULD NOT move.

If you route the belt starting from the crank, to the tensioner, to the front exhaust, then the slack should be on the rear exhaust to the crank.
This is what is important here. When you roll the tensioner to apply tension, the crank needs to roll clockwise and the cams SHOULD NOT move.

Then do two full rotations (clockwise) on the crank and set the crank in time, and the cams should be as well.

But like I said, if you are having trouble getting the crank to move, just route it backwards so the cams move instead of the crank.

TwIzTeD_3kGt
10-20-2010, 09:22 PM
My manual says to leave it a tooth back from TDC.

If you do it right, it'll align at TDC when you tighten the belt to the correct tension. Worked for me 3 times, no problems, and its not even a big hassle.

The manual also says to jack up the engine by the oil pan. Either way works, but my way is easier imo.

Mike-92RT
10-20-2010, 10:32 PM
yea, i dont use the oil pan HAHAHAHA... i use the front support lol

CoreyB
10-20-2010, 11:59 PM
I am with the majority here. Start at crank, move to rear then front and leave the slack at the tensioner. So easy a cave man could do it, or even me.

terrets
10-21-2010, 02:21 AM
Im surprised no one has mentioned cam lockers :). I did mine from crank to rear cams to water pump to front cams to tension. Had it back one tooth on the crank. Made sure I was setting the belt on the gears tight. Worked the first try :D It was my first timing belt ever o.O Also I used clips to hold the belt on the cams.. Just cause :)

blindmist
10-21-2010, 04:30 AM
Im surprised no one has mentioned cam lockers :). I did mine from crank to rear cams to water pump to front cams to tension. Had it back one tooth on the crank. Made sure I was setting the belt on the gears tight. Worked the first try :D It was my first timing belt ever o.O Also I used clips to hold the belt on the cams.. Just cause :)

Cause you don't need any of that crap if you do it backwards. :)

terrets
10-21-2010, 04:36 AM
Well I think using cam lockers on the front cams makes life easier. I got the rear two cams to chill on their marks but the front two wouldnt.

When I did my 180k maintance....I found the tensioner pulley was upside down!!! The belt was being warn from the bolt that holds the bracket. :lol:

TwIzTeD_3kGt
10-21-2010, 08:43 AM
Woah, that's a scary thought. ^^

Mike-92RT
10-21-2010, 02:47 PM
yea that is scary!!

i have the cam lockers and the tool (obv). Set the crank back a tooth, and things went very smoothly.. But everyone has their own method, to one their own :)

a2j
10-21-2010, 04:47 PM
so, looks like as long as everything aligned with right tension and pin can be removed and inserted back in, than its all good. no matter the way you do it.

blindmist
10-21-2010, 08:39 PM
so, looks like as long as everything aligned with right tension and pin can be removed and inserted back in, than its all good. no matter the way you do it.

Yes, but getting to this point when you are inexperienced with timing a 6G72 can be very frustrating.

terrets
10-22-2010, 02:50 AM
^ T'wasnt for me. :)

Ya it was a bit scary :lol: Good thing I didnt put it back together like that too :D Hehe

a2j
10-22-2010, 03:00 AM
alright, I will give it 12-16 hours and recheck everything just to be sure. my marks, tension and pin are where they suppose to be.

terrets
10-22-2010, 03:20 AM
Wooo! Goodjob.

ps. Where in WI are you? If you need any help... :) I love working on 3s's

blindmist
10-22-2010, 06:33 AM
alright, I will give it 12-16 hours and recheck everything just to be sure. my marks, tension and pin are where they suppose to be.

You will have to rotate the engine over to pull the pin on the tensioner if you wait that long. You would be amazed at how powerful that tiny tensioner really is.

a2j
10-22-2010, 01:19 PM
Wooo! Goodjob.

ps. Where in WI are you? If you need any help... :) I love working on 3s's

somewhere between GB and Appleton (half way). but its not that I need help, I kneed parts ;) . my wife helps me sometimes, like holding brake pedal or something.


You will have to rotate the engine over to pull the pin on the tensioner if you wait that long. You would be amazed at how powerful that tiny tensioner really is.

I was able to remove that pin and put it back very easy. I mean, there was no tension on that pin what so ever.

terrets
10-22-2010, 02:54 PM
Ok well I live in Kaukauna and Ive got an N/A Motor and shell sitting at my dads shop so if you need anything. :lol: The kid just did a 120k maintenance before he rolled his car even.

a2j
10-22-2010, 09:21 PM
I've seen a quite a bit damaged cars that just had their regular maintenance done. I think I know why they get in the accident... :)

PS: I live probably 10-15mi north of you

blindmist
10-23-2010, 05:42 AM
I was able to remove that pin and put it back very easy. I mean, there was no tension on that pin what so ever.

Wow, is this a new tensioner? I have never been able to pull the pin after about 6 hours of it sitting. I have had 0 timing belt issues. I have just never encountered one that lasted for 24 hours and the pin can be pulled except on bad ones which were 100% time reused ones. If it is a new tensioner I wouldn't worry about it.

a2j
10-23-2010, 02:30 PM
new tensioner, new pulleys, new belt :)

terrets
10-23-2010, 04:11 PM
I actually live over on the east shore of the Fox River between Wrightstown and Kaukauna :).

Tackhammer
01-11-2011, 11:04 AM
http://www.3sgto.org/f2/timing-belt-101-a-3109.html

wingnut
01-12-2011, 03:41 AM
^^^very nice sir :D