View Full Version : Oil weight
GordonRamsey
10-17-2010, 04:29 PM
Well its a pretty simple noob question. but can I run 15w-40 in my N/A? It calls for 10w-30.
stealthee
10-17-2010, 04:33 PM
I run 20w50 in the summer and 10w40 all other times. 15w-40 isnt going to hurt it.
GordonRamsey
10-17-2010, 04:36 PM
good because thats all they had in rotella. Im surprised Not many sell that anymore. does it still have all the additives that can breakdown a cat?
stealthee
10-17-2010, 04:37 PM
Consudering Rotella's popularity I doubt that's an issue.
GordonRamsey
10-17-2010, 06:08 PM
I'm not worried about the cat im worried about the lubrication.
blindmist
10-17-2010, 07:12 PM
If you want something that you can run for a long time, check out amsoil. The best shit in town. In a NA, You could probably run it 15-20k miles before needing to change it.
stealthee
10-17-2010, 07:13 PM
It would be ridiculous to run oil that long. Condensation will contaminate oil. I would NEVER run oil that long in any car.
GordonRamsey
10-17-2010, 09:08 PM
I know Aimsoil is real good. But I cant find much of anything anywhere. Pep boys was where I was at today, and even they had a small section.
stealthee
10-17-2010, 09:09 PM
You can get Rotella at Advance and even WalMart.
mcshooter
10-17-2010, 10:44 PM
a friend of mine , a cheap guy has a 1998 chevy with over 150000 miles on it changes his oil every 10000 or once a year and car runs fine. he uses mobile 1 0-30 .. we use rotella 5-40 in mikesvr4 and change it about once a year which is about 500 miles .. so i gets put to bed with new oil before the weather gets cold ..also never run the car without the engine coming up to temp.
rawavr4
10-17-2010, 10:48 PM
Stealthee, where did you get 20w-50? I cant find i anywhere.
GordonRamsey
10-17-2010, 11:26 PM
The walmart I go to doesnt have it.
stealthee
10-18-2010, 12:56 AM
Stealthee, where did you get 20w-50? I cant find i anywhere.
I dont use Rotella 20w50 if thats what you are asking. I just run cheap ass oil as I have 190k miles on my car. Well theres about 120k+ on the engine, but between what it leaks and the little it burns it would be wasteful for me to use anything else.
rawavr4
10-18-2010, 01:00 AM
No, i was just wondering where in to get it in general. No places around Easton sell it that I know of.
stealthee
10-18-2010, 01:01 AM
Every place I've ever bought oil from has 20W50.
blindmist
10-18-2010, 07:23 AM
I know Aimsoil is real good. But I cant find much of anything anywhere. Pep boys was where I was at today, and even they had a small section.
You have to find an Amsoil dealer. There is really no store that sells it. Not like Autozone.
Also, I just went to my Walmart in Lubbock, Texas, I could not find and 20w, highest I could find was 15w.
Mean Green
10-18-2010, 08:15 AM
Rotella at walmart is only about 11$ for the big jug. No sense in running Amsoil unless your car is boosted and you beat the shit out of it. Royal Purple is really good as well but I have always run Rotella in every car I've ever owned.
Rotella 15-40 w/ Purolator Pure One oil filter FTW.
GordonRamsey
10-18-2010, 01:04 PM
^ thats exactly what I got.
bluemax_1
10-18-2010, 03:55 PM
Wow... talk about some ridiculous and terrible so-called 'information' in this thread. Any tribologist would cringe.
OK, the topic is oil weight so listen up (read up?)
Oil weight is a measure of its viscosity or flow rate at a given temperature. Multi grade/viscosity oils like 5w30 or 20w50 are labeled as such from flow rates measured at 2 different temperatures, a cold flow rate and a hot flow rate.
These measurements are referred to in 2 commonly used units of measurement:
- centipoise (cP or mathematically, mPa.s) called the dynamic viscosity or simple viscosity
and the other unit of measurement (which is more commonly referred to in the US)
- centistokes (cSt or mathematically, mm squared/s)
- There is a 3rd unit of measurement, which is SUS (Saybolt Universal Seconds) where they measure how long it takes for 60 milliliters of a fluid to flow through a calibrated orifice in a Saybolt viscometer.
These measurements are made using a viscometer. The hot flow rates were initially measured at 210f in the original SAE J300 rating system in 1911, and later revised to 100c/212f in 1926. In 1952, they added the Winter (cold flow) rating, to address the difference in protection/properties between oils refined from black Gulf Crude vs. amber Pennsylvania crude. The amber Pennsylvania crude gave better cold protection (had better/lower cold viscosity) than oils refined from the black Gulf crude and the SAE began measuring cold flow viscosities at 0f to label the cold/Winter flow properties. The measured flow rates of a specific oil formulation are then labeled according to the viscosity range the SAE has spec'ed for a certain oil weight (i.e. a cold viscosity of 0, 5, 10 or 20, and a hot viscosity of 20, 30, 40, 50 or 60).
There are 2 other measurements that most folks aren't aware of or concerned with. These are the HTHS (High Temperature, High Shear) measurement, taken at 150c, and the cold cranking and pumping dynamic viscosities. The HTHS indicates the oil's performance under harsh conditions and its hydrodynamic fluid film strength (very important for highly loaded engines). The cold cranking and pumping measurements show the oil's viscosity at temps below 0c.
Understand that because the 2 numbers in a multigrade oil are taken at different temperatures, they CANNOT be compared to each other. What a 10w30 rating means is simply, "This oil flows like a 10 weight mineral oil at 0f, and flows like a 30 weight mineral oil at 212f".
These are the SAE determined hot viscosity ranges (at 100c):
SAE 20 = 5.6 - <9.3 cSt
SAE 30 = 9.3 - <12.5 cSt
SAE 40 = 12.5 - <16.3 cSt
SAE 50 = 16.3 - <21.9 cSt
SAE 60 = 21.9 - <26.1 cSt
A 10w30 oil has a viscosity of about 90 - 110 cSt at 40c(104f), and at operating temperature of about 212f, it should have a viscosity between 9.3 - 12.4 cSt. BUT at 0f, a 10w30 can have a viscosity of over 500cSt!!!
Just for reference here are some common kinematic viscosities:
Water at 20c = 1 cSt
Milk = ~4.3 cSt
Tomato juice = ~220 cSt
Honey = ~2200 cSt (about the flow rate of Lucas oil additive near 32f :p ).
So now you know what the oil weights are and what the viscosities are like at different temperatures. But what does it all mean?
Well, an engine (when new) is designed to be lubricated by oil of a certain viscosity range within a specific flow rate (vs rpms) at optimal temperatures. At higher temperatures, the oil thins out more, so at higher temperatures, you need a thicker oil to maintain the appropriate viscosity range to adequately protect the engine. There are also limits to the maximum viscosity the engine can pump and lubricate properly at (especially when cold) so you can't go too thick either (especially the colder it gets). This is why Mitsu specified 10w30 for most use and 20w50 in very hot temps. These recommendations are based on dino oils though (because they're aware that some folks prefer putting the cheapest thing they can find in the car).
Some newer cars, (as others have mentioned) spec thinner oils because they're designed with tighter tolerances (and potentially lower loads). Many of these new vehicles spec 0w20 oil because the thinner oil increases fuel economy (thinner viscosity = less fluid drag = better efficiency). If the engines are properly designed for it, there's no problem. Granted, there have been some folks who've had problems with using 0w20 in vehicles spec'ed for it, because the manufacturer spec'ed the oil mostly for fuel economy to allow higher mpg ratings, but the oil doesn't provide enough protection under more severe use, so folks driving harder blew their engines.
Anyway, to get back on track, the appropriate viscosity range oil for a particular car is dependent on the engine's tolerances (bearing clearances, power output, redline, oil pump flow etc.), operating conditions and temperature range. You need thinner oil for lower temps and tighter bearing clearances. Thicker oil for higher temps and greater bearing clearances. A high HTHS is important for highly loaded engines (turbo and especially modded turbo folks). Contrary to what folks might think, higher power does not necessarily automatically dictate a super thick oil. Generally, if you can run a thinner oil at higher flow rates, you're better off than a thicker oil at lower flow rates, however, the hydrodynamic fluid film strength is critical and the HTHS is an indicator of that. Why do I like Red Line so much? It has one of the highest HTHS ratings available for a given weight oil.
The 6G72 engine is designed for an optimal viscosity of about 10cSt at proper operating engine temperature (as are many other vehicles) at normal loads and ambient temperatures.
In practice, the theory is simply. You want the oil viscosity to be as close to 10 cSt as possible at ALL times, regardless of whether it's 40 below in Canada or 130f in Death Valley. If there was an oil with good lubrication properties that stayed at 10 cSt no matter the temperature, there would be no reason to ever buy anything else. Unfortunately such a fluid doesn't exist, which is why there are multigrade oils. The idea is to have an oil that is thinner at low temperatures so you don't see the insanely high viscosities (and therefore reduced flow) on cold startup, but one that doesn't thin out too much when the engine gets up to its normal operating temps.
With dino oils, they start with a lower viscosity base oil and use a combination of VII's (Viscosity Index Improvers) and PPD's (Pour Point Depressants) to achieve a decent multigrade. For example, a 10w30 dino may be made from 20 weight base stock with VII's added to stop it thinning out more than an SAE 30 weight at 100c, and PPD's to produce decent flow rates like a 10 weight at lower temps. VII's are long chain polymers. At lower temperatures, they remain coiled, at higher temperatures, they uncoil but to a limited amount, thereby limiting how much the viscosity thins out. The problem is, these polymer chains can be sheared, mechanically or chemically. When these VII's permanently shear, they can no longer inhibit the oil thinning out at higher temperatures and you now have the protection of a 20 weight oil at operating temps (or less at higher temps). I can tell you that this sure as hell isn't enough for a 6G72TT. Could you get away with it on an NA? I don't know. If driven very lightly and carefully (like the nutters putting Regular gas in these cars), you might be able to save some pennies (cheaper gas + better fuel economy from thinner oil). My advise though, would be to get a Kia.
Max
*** post too long, continued below
P.S. This post wa originally posted at about 10p.m. EST 10/18/10, don't know why it appears in the middle of the thread as posted at 2:55P.M.
bluemax_1
10-18-2010, 03:56 PM
continued...
The reason I dropped Mobil 1 0w40 like a hot rock is because this damn oil sheared to about a 20 weight in a very short time in my VR4, and this was with normal street driving. I hadn't even tracked the car yet when I did the UOA out of curiosity, which I'm glad of, because I discovered that there are a couple of people who've spun a bearing roadracing a 3/s with Mobil 1 0w40. Based on how fast the oil sheared in my engine, I think that a BPU (or higher) car could shear this particular oil within 3-4 flat out laps on a roadcourse. After that, a spun bearing is just a matter of time.
The thing is, even a 0w oil is too thick at 70f, much less 0f, so optimally if we could find a 0w30 oil (0 weight is the lowest cold viscosity oil available) that didn't shear/thin out, this would be absolutely ideal for a like new 6G72 engine with factory power output, driven in ambient temperatures around 65f - 80f that isn't run too hard. Problem is, not all oils are created equal (and some engines are harder on oils than others). Just about ANY 0wXX oil uses some VII's and PPD's. And the problem with VII's as I've mentioned, is that if/when they shear, you're left with the viscosity of whatever base oil it is they were using in the formulation.
Synthetics on the other hand have inherent multigrade properties. True synthetics can be formulated to a 10w30 with zero VII content. They also inherently flow better at lower temperatures. Red Line and Motul 300V can both formulate 10w40 oils with little to no VII's, meaning these oils won't shear down even under hard use. Under extreme temperatures, they will thin down to a lower cSt (as all oils/fluids do at higher temps), but synthetics tend to thin out less at higher temps than dino oils do (even Grp III hydrocracked oils) which is why a synthetic 10w40 can have a higher cSt at 230f than a 20w50 dino. And without VII's to shear, at a given temp, you will have the same viscosity as when you poured the stuff in the engine (barring outside contamination like dilution from fuel or coolant).
With my VR4 specifically, after discussing the specifics with one of the chief tribologists responsible for developing Motul's current 300V formulations, the recommendation was for the 10w40. He recommended their 5w40/5w30 for daily driving and their 10w40 for track use. This is for a 6G72 that is spec'ed for:
- Rod and main bearing clearances of about .00018"
- 8000rpm redline
- ~550awhp
- oil temps of ~230f
For anyone to say that a 0 weight or 5 weight oil is too light is to demonstrate their ignorance of tribology. While it's true that I personally would never use a 0wXX in the VR4 for roadcourses, for normal driving without track use (especially if I drove it in the winter), I would consider trying a decent 0w30 or 0w40 (Red Line now has 0wXX formulations) contingent on UOA's to see how the oil holds up. I HAVE used 5w30 and 5w40 oils in the VR4 in the winter and it's been great, even with my Tommi Makinen impressions whenever there was more than 4" of snow on the roads (what can I say, I miss my amateur rallying days). The oil held up just fine in UOA's. Then again, I don't use cheap stuff either. After trying Mobil 1 0w40 years ago (will NEVER use that stuff in a VR4 again) and Royal Purple 10w40 (sheared to a low 30 weight almost a high 20 weight within ONE track visit), it's been Red Line or Motul 300V for the VR4.
Saying that so and so's car blew something BECAUSE they ran the recommended 5w30 with NO reference to what oil it was, what the OCI was, how the car was run, little to no background on the car's condition etc. is akin to saying that carrying Wrigley's chewing gum in your pocket while walking around will result in a twisted ankle because someone you knew twisted their ankle while carrying a pack of Wrigley's gum in their pocket while walking around.
Of course, oil weight is just part of the equation, the actual formulation of the oil is important because there are also boundary lubricants, EP, AW additives, ester vs. PAO vs dino vs. Grp III hydrocracked stock etc.
As far as extended OCI's (Oil Change Intervals), that greatly depends on the car, the oil and how the car is driven. All street oils contain detergents to clean the engine, and they also contain acid inhibitors. The byproducts of the combustion engine, unfortunately can eventually turn the oil acidic. Street oils are formulated to a TBN (Total Base Number) which some UOAs (Used Oil Analyses) will display. If the oil is fairly common, or something the specific company has done a VOA (Virgin Oil Analysis) of, then you will have VOA vs UOA numbers to compare. The ONLY way I would advocate anyone trying extended OCI's is WITH a UOA (otherwise, you could potentially be asking for trouble). The UOA will show if your wear metals are within decent parameters, if there is any contamination from dirt (which would increase wear), if there is fuel contamination, if the TBN is too low (for some reason, your car is using up the acid inhibitors more quickly), if the particular oil you're using has sheared to a lower viscosity etc. If all, these parameters are fine, you can certainly extend your OCI's.
That said, WITH UOA's, I've discovered that with MY VR4, I can run 7,000+ miles on a single fill of Red Line 10w40. Potentially 10,000 miles or more (WITHOUT track use). 7,500 miles is the longest OCI I've ever gone though (with 1 track day). The wear metals were a little higher than I would like, but only to be expected (and still acceptable) given the track day. TBN was still good enough and wear metals were low enough to continue using the oil though. So yes, with a good oil, you CAN potentially run long OCI's. As mentioned though, I wouldn't recommend it without performing UOA's. Any significant fuel dilution, coolant leakage/mixing with the oil, dirt contamination from inadequate air filtration or any myriad of seemingly small issues can greatly reduce the oil's usable life though, and of course, as I keep saying time and again, not all oils are created equal.
But I'll leave that for another time, since I've come to realize that there are folks who like reading my posts, but there are also some who like to take some of the information from my posts and regurgitate it to sound knowledgeable without fully understanding what it means. Makes it more fun to correct them later. ;)
Max
elyria_boy
10-18-2010, 04:23 PM
I run schaeffer's 9000 series 15w 40. After pulling a 30 ft gooseneck enclosed trailer overflowing with tractor and semi clutches commercially for a 100k I discovered schaeffers was the only grease that I couldn't smoke. Before I would have to replace bearings and races every 2 months and hope I didn't catch a wheel on fire or have one f/y off going down the road and pass me. Yes, those things actually happened:.. saved the company thousands in repair bills. After that I will never run anything else. Look up their amp test online. Totally legit.
mb3000
10-18-2010, 04:47 PM
You have to find an Amsoil dealer. There is really no store that sells it. Not like Autozone.
Also, I just went to my Walmart in Lubbock, Texas, I could not find and 20w, highest I could find was 15w.
I have never been anywhere that did not offer 20w? Hmm
Hammer
10-18-2010, 06:38 PM
20W50 oil is way to heavy an oil for an NA engine. If your NA is stock 10W30 is perfect. If you want the best then use synthetic 10W30. 15W40 Is even too heavy. You can get by using 15w40 if it is synthetic during the summer in temps over 70F and if your engine has over 100,000 miles and has some bearing wear. Notice we are talking stock NA. Higher wieght oils do have special use circumstances in engines with high HP loads like over 500HP and up. NA's never get there. There have been studies done that show premature engine wear by using too heavy an oil in cold weather, example dino oil 15w40 in 30F temps. Cold starts in that temp or below with 15w40 dino oil will cause some oil stavation for the first 2-3 minutes. Synthetic oil does flow better when cold and a perfect cold temp synthetic oil would be 0W30 for an NA. Then 10W30 synthetic for the summer. Do not get caught up in using heavier wieght oil simply because race engines use it. They need it the bearing loads are 10-20 times higher than your NA engine.
This is just like a guy that uses race gas in a stock engine because he thinks it will go faster on race gas. That is a myth.
stealthee
10-18-2010, 06:44 PM
My use of heavier oil has nothing to do with race engines. I like to protect my engine and 0w is stupidly too thin.
I've got a friend that used the RECOMMENDED 5w30 in a basically stock NA 99 Mustang. The result was FRIED heads due to oil starvation because the oil became too thin.
Hammer
10-18-2010, 06:50 PM
My use of heavier oil has nothing to do with race engines. I like to protect my engine and 0w is stupidly too thin.
I've got a friend that used the RECOMMENDED 5w30 in a basically stock NA 99 Mustang. The result was FRIED heads due to oil starvation because the oil became too thin.
I doubt that story. There is something else going on that caused that. There are millions of cars doing just fine on 5w30 oil.
stealthee
10-18-2010, 07:17 PM
That story is 100% true.
The guy's name is Mark Trump and he is now a local city cop. This happened back around 03.
5w30 just cant stand up to abuse.
Hammer
10-18-2010, 07:22 PM
That story is 100% true.
The guy's name is Mark Trump and he is now a local city cop. This happened back around 03.
5w30 just cant stand up to abuse.
Ok Still sounds like snake oil sales to me. I would have to see it and inspect the damage myself to believe that story. Never heard or saw anything close to that caused by oil being too thin. :Suspect
stealthee
10-18-2010, 07:28 PM
What am I trying to sell? I'm relaying a story exactly as it was given to me by the owner and driver of the car. He had to have the entire top end rebuilt on a car with less than 60k miles on it. The shop that did the heads told him it was due to oil thinning and it wasn't the first time they had saw it. He started running heavier oil and never had an issue again.
blindmist
10-18-2010, 07:39 PM
The reason is fried was because it was a FORD MUSTANG. I have ran 5w30 in high performance motors plenty of times. 5w has nothing to do with it. I will put $1000 cash on it.
mb3000
10-18-2010, 07:46 PM
20W50 oil is way to heavy an oil for an NA engine. If your NA is stock 10W30 is perfect. If you want the best then use synthetic 10W30. 15W40 Is even too heavy. You can get by using 15w40 if it is synthetic during the summer in temps over 70F and if your engine has over 100,000 miles and has some bearing wear. Notice we are talking stock NA. Higher wieght oils do have special use circumstances in engines with high HP loads like over 500HP and up. NA's never get there. There have been studies done that show premature engine wear by using too heavy an oil in cold weather, example dino oil 15w40 in 30F temps. Cold starts in that temp or below with 15w40 dino oil will cause some oil stavation for the first 2-3 minutes. Synthetic oil does flow better when cold and a perfect cold temp synthetic oil would be 0W30 for an NA. Then 10W30 synthetic for the summer. Do not get caught up in using heavier wieght oil simply because race engines use it. They need it the bearing loads are 10-20 times higher than your NA engine.
This is just like a guy that uses race gas in a stock engine because he thinks it will go faster on race gas. That is a myth.
I use 20w50 in the summer and switched to 10w30 last weekend. Problem solved.
Hammer
10-18-2010, 07:47 PM
The reason is fried was because it was a FORD MUSTANG. I have ran 5w30 in high performance motors plenty of times. 5w has nothing to do with it. I will put $1000 cash on it.
I am right there with you! It must be something wrong with that particular engine. The shop probably pulled that excuse out of their ass. Maybe even to cover something the shop caused.
stealthee
10-18-2010, 07:56 PM
The shop had never touched the car before the head frying. He only took it to them on recommendation from someone else. They just reported what they found upon removal.
And yea, I don't run 20w all year round. I just run it in the summer. 10w40 all other times. I will never run anything as light as 5w in any car or truck I ever own.
Hammer
10-18-2010, 08:01 PM
The shop had never touched the car before the head frying. He only took it to them on recommendation from someone else. They just reported what they found upon removal.
And yea, I don't run 20w all year round. I just run it in the summer. 10w40 all other times. I will never run anything as light as 5w in any car or truck I ever own.
And is your car a stock NA?
Mean Green
10-18-2010, 08:02 PM
And is your car a stock NA?
http://i101.photobucket.com/albums/m74/nismo200r/owned-1.gif
mcshooter
10-18-2010, 08:16 PM
if i remember correct a lot of folks on bobs the oil guy run the 0-30 german gastrol, flow is the most important . a lot of foreign cars recommend 0-30 . i will look up some oil recommends on foreign autos
Hammer
10-18-2010, 08:35 PM
if i remember correct a lot of folks on bobs the oil guy run the 0-30 german gastrol, flow is the most important . a lot of foreign cars recommend 0-30 . i will look up some oil recommends on foreign autos
A lot of newer like after the year 2000 engines have very tight bearing clearances and take advantage of those very light weight oils. It is by design. Not every engine is built the same or has the same load factors. Our 6g72 can work on a 0w30 synthetic oil but only if the temp stays below 30F all the time that oil is in the engine. If your day time temps rise above 30F then use a 5w30 or 10w30 synthetic during the winter. The lighter if your engine has less than 100,000 miles the heavier over 100,000 miles. And this is for stock NA 6g72's.
Built engine owners already know what oil they should use. And it will be different than what the manual states. Turbo engines place a lot of extra heat into the oil as it flows over the turbo bearings. NA engine oil supply is not exposed to this kind of heat. Heat breaks down oil. Every oil has a max temp at which it breaks down. Once it breaks down it will stop lubricating your engine. Synthetics can take a lot more heat than dino oils can before they break down. But each brand is different depending on additives. This is why turbo engines have an engine timer option to idle the engine and keep the oil moving until the turbo cools.
Do not confuse N/A 3s owners with turbo 3s owners they have very different oil demands for the engine.
And stock vs built also place different demands on the oil. What works for one guy will not work for all. Each should use what is best for his application.
If you are stock the manual is best for your application.
stealthee
10-18-2010, 09:06 PM
And is your car a stock NA?
My car is whats in my sig. Basic bolt ons on a SOHC. My oil causes me no issues.
mb3000
10-18-2010, 09:14 PM
And is your car a stock NA?
I also own a SOHC, stock except for a K&N filter.
GordonRamsey
10-18-2010, 11:02 PM
Well I have 15-40 in there now and well see what happens. I just put it in 2 days ago and ran it for about 3 minutes. I'm not changing it again.
stealthee
10-18-2010, 11:28 PM
Its not going to hurt your engine. You'll be 100% FINE.
bluemax_1
10-18-2010, 11:47 PM
How the heck did my long posts end up in the middle of the thread?
Max
DocWalt
10-19-2010, 12:03 AM
The server has time issues occasionally. Great stuff anywho, Max :)
Hammer
10-19-2010, 12:13 AM
How the heck did my long posts end up in the middle of the thread?
Max
Hi Max, Just a quick thought. Your engine oil temp gauge does not tell you the true max temp your oil is exposed to. Try placing an oil temp probe right at the oil return line off of the turbo to get a true max temp reading of your oil before it goes thru the oil cooler.
Then check that temp against the thermal limit for your oil brand.
bluemax_1
10-19-2010, 01:07 AM
Hi Max, Just a quick thought. Your engine oil temp gauge does not tell you the true max temp your oil is exposed to. Try placing an oil temp probe right at the oil return line off of the turbo to get a true max temp reading of your oil before it goes thru the oil cooler.
Then check that temp against the thermal limit for your oil brand.
Yeah, the hottest temps the oil sees are on the walls of the cylinders in the combustion cycle, between the bearings and crank journals and in the turbos. Temps there can potentially hit double what a regular oil temp gauge sees. Run oil that is too thick and 400+f temps at the bearings can melt/wear away the lead babbitt layer on trimetal bearings which is why I run bimetal King bearings, which can withstand 1100f temps (not that they'll EVER get that hot, the engine would be blown way before that but it's a safety margin). That's one of the other reasons I like Red Line and Motul 300V in these cars, esters are MUCH more resistant to high temps and thermal degradation/coking than even PAO (PolyAlphaOlefin) synthetics and unquestionably better than dino oils at resisting high temps. With no leaks, and good compression, these oils burn very little even in the cylinders and they don't show coking.
Max
Mean Green
10-19-2010, 06:01 AM
Rotella is used in tractor trailers and many other heavy pieces of machinery and with Delvac. Considering the temps that Diesel's get to, I would definitely be willing to put my money on Rotella considering the amount of abuse those engines see on a daily basis. Delvac and Rotella where specifically designed to handle very high heat situation for obvious reasons otherwise they would not be certified to run in machinery.
No, our cars are not "Heavy Machinery" but our cars oil temps do not get as hot and do not run hot continually through an 8 hour work day. The equipment that does last for many more hours than even what our cars where designed for run it and they last YEARS without mechanical / internal engine failures. I cannot say the same for any other conventional motor oil.
mcshooter
10-29-2010, 11:58 PM
for you guys who are going to send your used oil to blackstone labs i suggest you put the blackstone container in a box to mail it. i took a sample to our local post office in blackstones container and was asked what it was. i told the clerk it was a used oil sample and you would of thougth it was a aids sample or neucler waste. i had to put it in a box to ship it. blackstone labs has a self addressed label and you have it in 2 bottles but it still scared the postal clerk.
Chris GTO TT
10-30-2010, 02:42 AM
Blackstone has a letter on their website that explains that their packaging is USPS approved. I always ship it without extra packaging and never have an issue.
bluemax_1
10-30-2010, 05:16 AM
With all the folks scared about terrorist attacks and crap these days, it's potentially easier to just put the bottles in a box. It really varies from post office to post office. Even before this crap some post offices still didn't quite get that used motor oil is harmless, and when you tried to explain WHY you were shipping a small bottle of used motor oil, you'd get a look I'd expect for explaining why I'd stick my head in a pool of acid. Only nutty automotive enthusiasts like us are even aware of the existence of used oil analysis.
Max
The reason is fried was because it was a FORD MUSTANG.
lol Amen
in my non-sports cars (Acura TL, Civic EX) I use Mobil1 0W30 Synthetic oil. Works great, especially during the winter when its 0-10 F outside in the morning.
in my VR4 I use 20W50 Castrol and 10W40 (wanna switch to 5W40) during cold winter days. non Synthetic. change every 2-3K miles
GTOJOE
10-31-2010, 03:41 AM
Subscribed for reference.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.