View Full Version : 6G72 Crank Lamp
Greg E
10-11-2010, 08:27 PM
There are so many stories of spun bearing 3/S motors out there, it's quite saddening. What's worse is, many of those cranks were just scraped. Most scrap yards will give you $10-$20 at the MOST for a complete engine. Almost not even worth scrapping...
Well... Another project I'm working on is turning the crank from my coffee table into a lamp for my apartment. Here's the story on the coffee table (http://www.3sgto.org/showthread.php?1489-6G72-Coffee-table)
The idea is simple. Take the crank, bolt the flywheel to it and weld a piece of lamp rod to the front end.
Here it is assembled.
http://imgur.com/kWWbN.jpg
http://imgur.com/MUObP.jpg
I had so many used flywheel bolts it was maddening. At least here they could be useful!
http://imgur.com/FrLLL.jpg
Lamp rod welded in place. Next time, I'll chop off the crank pulley bolt, put it in a lathe, drill a half inch hole in the center, and tap it for the lamp rod. The weld didn't come out as good as I was hoping. Even after sanding it down to look better...
http://imgur.com/4pgVE.jpg
Here it is after a night in the oven at 850 degrees to burn off all the oils.
http://imgur.com/Re4tw.jpg
Masking tape covered with 4 layers of duct tape protect the lap rod from the blaster.
http://imgur.com/1JTKD.jpg
Here they are wrapped in plastic with 2 incandescent bags to keep the moisture from rusting the steel. Ready for powdercoating!
http://imgur.com/evJxK.jpg
The crank lamp will be coated the same color as the engine coffee table.
Greg E
10-11-2010, 08:29 PM
Lowes also sells the pieces I need to make the light fixture itself.
http://images.lowes.com/product/converted/081069/081069507204lg.jpg
Cost was about $9. They had other fixtures there like a pull chain or touch sensor, but I didn't opt for those as it'll be plugged into a switched outlet.
Only thing I need to buy is a lamp shade. Haven't even started looking for one yet...
Austin@STM
10-11-2010, 08:36 PM
Very cool idea i like the table a lot, im gonna read that thread now.
Greg E
10-11-2010, 08:40 PM
Very cool idea i like the table a lot, im gonna read that thread now.
I was also thinking of making one out of a cam, but couldn't come up with a way to drill a half inch hole ALL the way thru it...
On the crank lamp, the power cord will just come out the switch socket and down the back side.
CoreyB
10-11-2010, 09:12 PM
Nice, you like heavy furniture huh.
Greg E
10-11-2010, 09:38 PM
Nice, you like heavy furniture huh.
It's not that bad. The crank is 42lbs with the stock flywheel attached. The motor is 82lbs.
Flamer
10-12-2010, 04:10 AM
Heavy ass lamp, dayum!
terrets
10-12-2010, 04:20 AM
Im making lamps with my crank bearings and lifters welded in a mitsu symbol :D. You should get a white lamp shade and put a vinyl Mitsubishi symbol on it :D. Or prints of the car...Theres got to be a place that makes custom lamp shades.
akotten
10-14-2010, 08:49 PM
I've got exactly what I need to make both of these (table and lamp). My new winter project! Best dorm room furniture ever
Greg E
12-13-2010, 08:12 PM
First stage of the powder coating is finished!
http://i.imgur.com/FCIfp.jpg
http://i.imgur.com/lZcvm.jpg
Greg E
12-14-2010, 08:36 PM
Sprayed and baked the black metallic this afternoon!
http://i.imgur.com/lz3oB.jpg
Unfortunately the pic doesn't do the powder any justice. It's truly an awesome looking color in person!
Greg E
12-15-2010, 10:00 PM
Picked these up some time ago to pad the flywheel from scratching up the table. I wanted black but they didn't have any...
http://i.imgur.com/dDGZX.jpg
The larger ones didn't fit so I had to use the 38mm ones.
Assembly underway...
http://i.imgur.com/ctCB8.jpg
All finished!
http://i.imgur.com/9Fgwm.jpg
Lowes didn't have a great selection of lamp shades, so I just used one I had sitting around the house for now. I'll spend the next few days shopping for one. Probably get a really large one too since the medium size seems puny compared to the huge crank.
green-lantern
12-15-2010, 10:28 PM
Awesome!
CoreyB
12-16-2010, 10:22 AM
Love it. The only thing I would of done different would be to do the chrome first like the engine, then mask off the journals and then do the black. Not taking anything away from what you did though. Its just awesome and I really like the way the engine table came out.
Greg E
12-16-2010, 10:56 AM
Love it. The only thing I would of done different would be to do the chrome first like the engine, then mask off the journals and then do the black. Not taking anything away from what you did though. Its just awesome and I really like the way the engine table came out.
I was originally going to do it that way but there's no good way to remove the masking tape after spraying the powder without disturbing it. The journals are too small and the space is too tight.
OH! I forgot to mention. The motor came out of a green 1G stealth just like the model sitting in front of the lamp.
Granny
12-16-2010, 11:25 AM
I like!
You need to be creative with the lamp shade to really finish it off.
If you could fit together 3 or 4 of them it would be a good idea for a floor lamp as well.
Greg E
12-16-2010, 12:10 PM
I like!
You need to be creative with the lamp shade to really finish it off.
If you could fit together 3 or 4 of them it would be a good idea for a floor lamp as well.
You just gave me a great idea for the cams! I can weld a couple of them to the crank. It would look badass! Thanks granny!
Atrosity
12-16-2010, 01:15 PM
Wow this look freaking amazing!! This a cast crank? Lol!
get a professional to do an HDR pic of your 3/s & silkscreen it onto fabric. then have an upholstery shop make a lampshade out of it. ;)
p.s.
2nd idea:
get a bunch of stickers from our primary 3/s shop sponsors and create a "nascar-style" lapshade.
Granny
12-16-2010, 11:15 PM
You just gave me a great idea for the cams! I can weld a couple of them to the crank. It would look badass! Thanks granny!
Nothing you didn't already think of.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.