View Full Version : Using a Honda AEM EMS on a Mitsubishi 3000GT VR4
If anyone is looking for a cheap EMS solution you might find this useful.
Original post: http://roycormier.net/2010/10/20/how-to-use-the-aem-ems-30-1020-as-a-universal-ecu/:
The AEM EMS 30-1020 is an older Honda EMS. At the time of writing this they can be found for about $500 or less, I got this one for $400 on eBay.
http://roycormier.net/images/projects/AEM_1020_1.jpg
Most of the Series 1 AEM boxes have internal jumpers that can be moved to change the Cam and Crank sensor types from MAG to Hall Effect. Unfortunately the 1020 doesn't have these jumpers, so some hardware modifications are necessary. So I busted out the multimeter and got to work tracing the Cam and Crank inputs.
On the 1020 the Crank and Cam sensor inputs are on pins C2 and C4. These run to resistors R11 and R30, which are then connected to ground. To use a hall-effect sensor for cam/crank input the signal wire needs to be pulled up to +5V.
http://roycormier.net/images/projects/AEM_1020_4.jpg
I de-soldered the right leads on the R11 and R30 resistors then bent them out of the way. Then I soldered in some 2.2K ohm resistors and connected them to the right side of resistor R188.
http://roycormier.net/images/projects/AEM_1020_3.jpg
Then I had to change the position of jumpers JPC1 (coil 1 ), JPC2 (coil 2), and JPC3 (coil 3). I'll be using 3 coils on a 6g72 V6 doing wasted spark
http://roycormier.net/images/projects/AEM_1020_2.jpg
And thats it for the hardware modifications, now you just need to make a custom ECU harness and you're all set.
---------------------------------------------------------------------------------------
I went down to the junkyard yesterday and picked up the Honda ECU connectors for $5.25. Then I spent a couple of hours last night making the custom ECU harness for the 3000GT VR4.
ECU Connectors from a 1997 Honda Civic:
http://roycormier.net/images/projects/IMG_2508.JPG
Cutting out the stock 3000GT connectors
http://roycormier.net/images/projects/IMG_2510.JPG
http://roycormier.net/images/projects/IMG_2513.JPG
All done.
http://roycormier.net/images/projects/IMG_2516.JPG
And it works.
http://www.youtube.com/watch?v=tevXIXwQ1Aw
Chris@Rvengeperformance
10-08-2010, 03:11 PM
very nice, you are braver than me
SpdDmnVR4
10-08-2010, 03:40 PM
Im impressed. This is a good idea, but im not good enough with a soldering iron to trust myself to that kind of modification. It was asking alot to solder in my ECU's new capacitors.
Post up after you get it tuned..
2fnloud
10-08-2010, 05:49 PM
OP, you are a brave soul! I am glad I got my 3s AEM EMS v2 for the stupid low price I did. I would NEVER have the heart to hack up the original ECU harness like that.
mh3kgt
10-08-2010, 06:37 PM
:eek: Good work! I'd be too scared to hack the ECU harness off though....
KeithMac
10-08-2010, 06:55 PM
Good job, if you`ve got faith in your ability why not!.
thor'svr4
10-08-2010, 08:53 PM
i wish i knew enough about circuits to do that, to me you might as well have been talking another language in that 1st post. my knowledge of resistors is limited to what i was taught sr. year in high school physics... one day ill make a real attempt to pick up computer stuff. congrads on trying something new and making it work.
CoreyB
10-08-2010, 09:07 PM
Great work man. That actually looks fairly easy. You did the hard work which is figuring out what to change. I could care less about cutting the harness. Its your car, do what you want.
VR4's-kick-ass
10-08-2010, 09:12 PM
bad ass!
wow, that is totally awesome! could you do that to my car? ;)
PS: btw nobody should ever doubt in Roy. He know what he is doing!
CoopKill
10-08-2010, 11:15 PM
In for results...
wow, that is totally awesome! could you do that to my car? ;)
Yeah, I could probably do that sometime.
CoreyB
10-09-2010, 12:04 AM
Does it run well? The video only showed cranking.
green-lantern
10-09-2010, 01:14 PM
Why didn't you pick up a cheap boomslang harness? Just the plain ones are pretty cheap.
Anyway I'm interested in the results on how it runs.
Unknownvr4
10-10-2010, 08:48 PM
subscribed...
Hard AttacK
10-10-2010, 09:11 PM
AWESOME!!! I <3 you
Are you going to post up a wiring schematic?
Unknownvr4
10-10-2010, 11:46 PM
^ That and will it work on a 2nd gen car??
I won't have any results for a while, for now I'm just using the same map from my previous single turbo car that had an AEM EMS.
It'll work on 1st and 2nd gen cars. You have to make sure the AEM box has at least 3 available coil outputs to run a V6. The specs are listed in the installation manuals for each model which can be found on google.
For the wiring, I compared the manuals from the 30-1311 to the 30-1020 and matched up the pins. Several pins have to be moved on the Honda connectors to support the 2 extra injectors, coils, and a few other things. Theres more than enough unused pins to support all the outputs needed for a 6g72.
At a minimum you'll want to wire up:
Power
Power Ground
Sensor ground
Logic Ground
Crankshaft position sensor (CKP)
Camshaft position sensor (CYP)
Injector 1,2,3,4,5,6
Coil 1,2,3
MAP
IAC
Fuel pump relay
RAD Fan Low
RAD Fan High
VSS
Coolant temp
TPS
Sensor voltage
Knock sensor
O2
green-lantern
10-11-2010, 12:07 PM
Have you got it to start yet?
futurevr4man
10-11-2010, 01:10 PM
dang thats interesting. good job!
No I haven't attempted to start it yet. The coils and injectors were disabled in the video to keep the engine from starting. Stat Sync'd comes ON which means the EMS is reading the crank/cam position properly, and is ready to start. It should run the same as the 30-1311.
There aren't any headers on the car right now, and I don't feel like starting a fire in my garage. But it'll probably be running again before the end of the year, every time I watch a good car video on youtube I get more motivation to finish it.
Now I'm working on a custom serial gauge that reads the AEM telemetry to display on an LCD in the dash. I think its gonna be pretty cool..
green-lantern
10-11-2010, 03:14 PM
Well get to work bro. I'm very interested to see how it all works out. :)
ChargerX3
10-11-2010, 05:18 PM
In for the final results. +1 for ingenuity.
GTOJOE
10-12-2010, 06:12 AM
Also in for results.
Unknownvr4
11-04-2010, 09:18 PM
I cant even find the 30-1020 for sale on ebay :(
3000GT MR
11-04-2010, 10:16 PM
i guess you can hack up a boomslang harness.. very interesting. Is there a way to use a honda v.2 or it has to be the older one?
I cant even find the 30-1020 for sale on ebay :(
Try the classifieds on http://hondamarketplace.com/, When I first started looking a few months ago I saw a few pop up on there every couple of weeks. The 1050 would be one of the easier ones to use since you can simply change jumpers instead of soldering in resistors.
Is there a way to use a honda v.2 or it has to be the older one?
I'm not sure, but If you're going to spend that much money I'd recommend just buying the box made for the 3000GT.
J. Fast
11-04-2010, 11:46 PM
Snap! Where did you learn your electrical wiring skillz? Nice project.
x2xtreme360
11-05-2010, 12:12 AM
I've had this question for a long time... does the AEM EMS systems allow the OBDII cars to pass inspection? I imagine the OBD port is no longer functional.
3000GT MR
11-05-2010, 02:38 AM
so the 1050 is the same as the 1020 but uses jumpers instead of soilder? i see 1050's all over the place.
Unknownvr4
11-05-2010, 12:53 PM
I believe im going to do this as well
deathsled
11-05-2010, 07:38 PM
I've had this question for a long time... does the AEM EMS systems allow the OBDII cars to pass inspection? I imagine the OBD port is no longer functional.
AEM EMS absolutely will not pass OBD2 inspection.
so the 1050 is the same as the 1020 but uses jumpers instead of soilder? i see 1050's all over the place.
Yeah, this document explains the jumper settings as well as some other interesting things: http://roycormier.net/doc/AEM_undocumented_settings_v1.2.doc
Unknownvr4
11-20-2010, 11:35 PM
Pictures are down Roy. I plan on doing this reallllll soon
Damn I never noticed that, thanks for letting me know. They should be fixed now. I've been getting some work done on the car lately, so I might be able to start it up within a few weeks.
[Sat Nov 20 2010] [error] [client *.*.*.*] Options FollowSymLinks or SymLinksIfOwnerMatch is off which implies that RewriteRule directive is forbidden: /var/www/w/roy/images/projects/AEM_1020_1.jpg, referer: http://www.3sgto.org/showthread.php?1429-Using-a-Honda-AEM-EMS-on-a-Mitsubishi-3000GT-VR4
Unknownvr4
11-20-2010, 11:50 PM
Not quite understanding the jumpers thing.. probably just because i skimmed over it real quick. Its supposed to be easier than what you did? To me, soldering in resistors would be easy...
Yeah, If you look at this (http://roycormier.net/doc/AEM_undocumented_settings_v1.2.doc) document I think it explains the jumper settings. Theres 2 positions available, one is MAG VR, and the other is hall-effect. On some of the boxes the resistors are already in place so you can just change jumper positions for the type of sensors in use.
Unknownvr4
11-20-2010, 11:58 PM
Ok.. i went to LKQ today and got 97 civic ecu plugs.. They let me have them for free since it was all i had and today was %50 off
With the jumpers, you literally open it up and switch them in different positions? Thats what im getting from the document.
Unknownvr4
12-17-2010, 12:51 PM
Bump. Any updates?
Well I tried buying some header flanges from IPS Motorsports, and apparrently they're never ever going to ship, just like last time I tried buying them.
So I'm trying to find a place locally to get some flanges cut with a waterjet. Then I can finish the new single turbo kit and get the car running.
Unknownvr4
12-17-2010, 02:01 PM
Im a newb to aem, is there a base map we could download or something so the car runs correctly? I havent gotten a aem yet, just trying to ask some questions and make sure everything goes well before i jump in too.
Yeah, the AEMPro software comes with basemaps for the 1st and 2nd gen 3000GT/Stealth.
J. Fast
12-18-2010, 12:32 PM
A company out of California called Specialty Products and Design Makes flanges for our cars if your still looking for a set Roy.
Cool Thanks, I found a PDF with their prices so I might give them a call next week.
Well I really hate cold weather and haven't felt like going out in the garage at all lately. So since I was too lazy to get wood for the wood stove, I decided to buy a natural gas heater as a birthday present.
I went with a fairly small unit, but it has no problem heating the 1050 sq-ft garage since its' insulated pretty well. With the thermostat set at 53 the heater doesn't run very often, and thats warm enough for me to stay out there for a few hours. Luckily the gas line and electrical wiring were already ran a corner in the back of the garage.
http://roycormier.net/images/heater3.jpg
http://roycormier.net/images/heater1.jpg
http://roycormier.net/images/heater2.jpg
well, that is just awesome. Its about 30-35 deg in my garage, can't really work for more than 1-1.5 hours. I wounder if they make some used oil burner heaters or some like that...
If you want a wood stove I might be able to sell the one I have, with a bunch of free stove piping too. You'd just have to run it through your roof. But it is nice to be able to just set a temperature and wait for it to warm up.
green-lantern
12-19-2010, 09:03 PM
Well I really hate cold weather and haven't felt like going out in the garage at all lately. So since I was too lazy to get wood for the wood stove, I decided to buy a natural gas heater as a birthday present.
God I know what you mean! You live in the wrong place to hate the cold. My car is ready to drive and I can't even bring myself to put the damn bumper on. I can't stand the winter, I do like the snow though :D.
Happy birthday!
deemo99
12-22-2010, 10:25 PM
You could try Absolute in the valley for waterjet flanges. We buy laser, flame, and waterjets at the shop. If you need help connecting with someone who can help you out let me know and I'll try to help you out.
Dave
Unknownvr4
01-04-2011, 10:09 PM
Would a 30-1010 work?
I would think so. According to the documentation it has enough spare coil and injector outputs.
Unknownvr4
01-05-2011, 11:31 PM
How would i pin in the spare injector outputs?
Mine (30-1010) is for an (OBD2B) integra and i found the pinout for it here http://technet.ff-squad.com/wiring.obd2b.htm
Now if im not mistaken, i do not have to use plug in "D" correct?
It looks like you might need pin D1 (Idle #3) which is pin 5 on the 3000GT/Stealth EMS.
For injectors 5 & 6 you could use B19 and B16. Theres a few more available listed in the PDF.
Since I was working on a friends car tonight, and he brought over free beer, I'll have to review my post in the morning for accuracy... :lol:
Unknownvr4
01-06-2011, 02:04 AM
It looks like you might need pin D1 (Idle #3) which is pin 5 on the 3000GT/Stealth EMS.
For injectors 5 & 6 you could use B19 and B16. Theres a few more available listed in the PDF.
Since I was working on a friends car tonight, and he brought over free beer, I'll have to review my post in the morning for accuracy... :lol:
LOL its all good
Im just glad for your quick responses and hopefully you arent getting annoyed with me asking so many questions
Alright, now that I'm sober I looked into it some more. The 1010 doesn't seem to have an "Injector #3" pin, so if you were to use B16 (Injector #8) as injector #3, I think you'd have to modify the injector phasing so #8 fires as if it were #3.
If you go into the Full Options list in AEMPro theres "Inject tooth #1", "Inject tooth #2", etc... I *think* you would turn off Injector #3, turn on #8, and copy the value from "Inject tooth #3" to "Inject tooth #8". And under Options->Injector make sure #8 is "Primary". But I have never tried this personally.
So I would match up all injectors with the correct pin in the 1010 diagram (1,2,4,5,6), then choose a pin such as B16 for Injector #3.
http://roycormier.net/images/projects/Screenshot.png
Unknownvr4
01-06-2011, 06:44 PM
Alright, now that I'm sober I looked into it some more. The 1010 doesn't seem to have an "Injector #3" pin, so if you were to use B16 (Injector #8) as injector #3, I think you'd have to modify the injector phasing so #8 fires as if it were #3.
If you go into the Full Options list in AEMPro theres "Inject tooth #1", "Inject tooth #2", etc... I *think* you would turn off Injector #3, turn on #8, and copy the value from "Inject tooth #3" to "Inject tooth #8". And under Options->Injector make sure #8 is "Primary". But I have never tried this personally.
So I would match up all injectors with the correct pin in the 1010 diagram (1,2,4,5,6), then choose a pin such as B16 for Injector #3.
There is a pin for injector 3, its B4
Edit or are you comparing the 1010 pinout to a 3000gt ems pinout?
Edit2: oh my bad, i found the 1010 manual so im looking at that too now
Yeah, thats Injector 3 on the Honda ECU but Injector #4 on the AEM EMS.
Unknownvr4
01-06-2011, 07:19 PM
Yeah, thats Injector 3 on the Honda ECU but Injector #4 on the AEM EMS.
Edit: Theirs 3 rows on the 1010 manual, the first being the car pinout, the second being the 1010 pinout and the third being availability. If i understand correctly, i just wire everything out to the 1010 pinout and ignore the car pinout correct?
Edit2: after reading and looking at it a few times i believe i was correct in edit 1 of this post.
Unknownvr4
01-07-2011, 03:55 PM
For the resistors, i picked up 2.2k ohm resistors but i think i may have picked up the ones. Mine look alittle larger than yours and mine are 1/2 watt 5% tolerance
And also, for the coils, do they just pull out?
The jumpers for each coil? Yeah, those will slide right off to change position.
Unknownvr4
01-08-2011, 12:48 AM
The jumpers for each coil? Yeah, those will slide right off to change position.
Ok and what about the resistors? What wattage and tolerance did you use?
I think you'd be just fine with the 1/2 watt. I can't find the package from my resistors, but I would guess 1/4 watt 5% tolerance, I got them from radio shack.
Unknownvr4
01-08-2011, 11:15 PM
I went to radioshack and bought pretty much all different wattages since they're only 99c a pack..
I compared which ones i had to the ones you soldered in and the ones that matched the closest were the 1/8 watt ones.. all the other wattages are longer than the 1/8s
Unknownvr4
01-09-2011, 07:55 PM
Would it be possible to use a stock honda map sensor too?
:suspect:
I'm not sure of the specs on the Honda MAP sensors, but I don't think they'd support high enough pressure. The stock MAP sensors I've used in the past on other cars weren't good for more than 5-10 psi.
Well I'm getting really close to being able to start the car now. I put in oil and coolant tonight so I could turn it over, I've got spark on all 6 cylinders which is good. I just have to put the intake manifold on and buy an alternator belt, then I can finally try to start it.
Unknownvr4
01-15-2011, 11:11 PM
Sweet im so ready.
Well I was hoping to have a much longer video than this, but my IACV doesn't seem to be working anymore, so the car won't idle. But at least it runs a bit :lol:. I also don't have a wideband yet so it was running way too rich. I'll probably work on it again in a few days and try to make it driveable.
The squealing in the background is my truck, I had to use it to jump the car since I don't have an alternator belt yet.
http://www.youtube.com/watch?v=EyaTH_HK4Ak
green-lantern
01-16-2011, 08:39 PM
Cool, I hope you get it going good soon.
HLxDrummer
01-16-2011, 08:54 PM
Awesome man! So what your saying is I could get a 1050, switch the jumpers, load the 3000GT map, wire it in, and it would work like one meant for a 3000GT? If it doesn't cause any stupid little issues I would so do that!
Can you use the AEM EMS without the IAT/MAP sensor? Just with a stock setup?
I wanted to get an AEM for a while but too expensive and since this car is my DD I don't want to risk not being able to tune it, but for $500 I'd try this and swap in my OEM ECU until I get the AEM fully tuned.
Yeah basically. A friend of mine is running the 1050 on his IS300 and its' been working great for 2 years.
You can run MAF or MAP. The 3S Basemap is setup for MAF. I ran without an IAT sensor on my other VR4 for a couple of months.
HLxDrummer
01-16-2011, 10:52 PM
Awesome, thanks!
I finally got the car to idle today. My MAP sensor is putting out .48 volts when it shouldn't go under .50 according to the AEM calibration. So it was using the TPS as load and was wayyy off. I've got to figure out whats up with that.
My Fuel map is all jacked up right now, but it runs.
So finally, heres a 3000GT running on a Honda AEM EMS.
http://www.youtube.com/watch?v=EzaQHRyQ1xc
green-lantern
02-05-2011, 07:29 PM
Very cool! congrats!
What was that loud noise? Was it backfiring?
Yeah its' been backfiring a bit, the A/F is all over the place. The downpipe isn't connected to the exhaust so its' pretty loud.
green-lantern
02-05-2011, 07:32 PM
Yeah its' been backfiring a bit, the A/F is all over the place. The downpipe isn't connected to the exhaust so its' pretty loud.
Got any plans on going to the dyno? Are you going to tune it yourself?
I'll be doing some street tuning using the AEM Logs and virtual dyno software. The fuel map was a piece of cake last time, though I didn't touch the timing. I'll see how it goes, I'll probably end up having to rent some dyno time this summer.
CoreyB
02-07-2011, 03:48 PM
Very cool. Didnt sound like it was running on all cylinders though.
Unknownvr4
03-11-2011, 02:19 AM
Mind sharing your map? im going to be starting mine up soon
My laptop died last week while I was in Texas. I'm waiting for my replacement, then I could pull teh map off the EMS if you still want it. But its basically just the basemap modified a bit with some minimal idle tuning done. I've been trying to save money for other things over the past month or so, so the car is on teh back burner. I'll probably get teh itch to make it drivable once it starts getting warm again.
terrets
04-02-2011, 01:16 AM
Could I come along for the street tuning? :D
Yeah sure. I need to finish my downpipe, heat-wrap a couple of things, renew my plates, and put some insurance on teh car again. So maybe sometime later this month.
terrets
04-02-2011, 03:29 PM
Awesomeee. :D
Unknownvr4
05-10-2011, 03:45 PM
More videos??
niterydr
12-21-2011, 08:11 PM
Bumping this one out of curiosity...
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.