View Full Version : Car runs, but now......
GRSHOPR
10-07-2010, 10:32 PM
OK, so for those that haven't read the other entire 20 page thread, here's a low down, and what the current problems are.
I just finished swapping in a 91 JDM TT motor, ECU, and harness into a 94 base. There have been a lot of issues, but now it's running, if rough. Right now, the biggest issue is the radiator.
I followed the instructions at the link below, but the fan still won't turn on for anything. At the relays for the fans, there is power to pins 1 and 5, and possibly 3 (it varies for some reason?). If the engine gets warm enough, the driver's side fan will kick on to cool the motor, but when I turn on the AC, it doesn't turn on. Anyone got any ideas on this one? I'd wire a separate relay into this thing and call it done, if I could somehow slave it to the temp, so the fans would turn on like they're supposed to, but I'm not sure how that'd work. Thanks for looking!
http://www.3si.org/forum/f53/1g-harness-2g-body-274771/
Austin@STM
10-08-2010, 12:28 AM
Have you hooked up power to the fan to know that its even good?
GRSHOPR
10-08-2010, 01:31 AM
It is indeed. At one point I was able to ground pin 5 and have it run. And before I put it in, I tested both fans.
colt45 gto
10-08-2010, 04:39 AM
JDM radiator? is the rad in good shape?
i mean sometimes those rads clog in the bottom rail where the senders are, they will not find heat if they are covered in sludge
GRSHOPR
10-08-2010, 10:14 AM
No, it's a usdm, but I flushed it before I put it in. The reason it makes me think that it isn't the sensors is that sometimes, pin 3 does and does not have voltage. I haven't actually tested to see if this is related to the engine temp yet, but it does make sense. Unless I'm completely backwards on how that circuit functions.
elyria_boy
10-12-2010, 02:41 PM
For 20 bucks at any parts store you could get an adjustable high temp regulator. I converted an air cooled engine to liquid cooled and used one to turn the electric water pump when it gets to a certain temp. They are for fans tho. Put sensor inline, turn screw to have it turn on between 150 and 210 degrees. Simple easy fix.
GRSHOPR
10-14-2010, 02:32 AM
Sounds like a winner, thanks elyria.
OK, so I'm bringing everything back to this thread. I've compiled a list of the symptoms of the car that need to be tuned, and if I have theories or steps I'm going to take on each one, I'll list them accordingly. If there are no ideas, I could use yours, guys, since I'm lost. I've never tuned my own car before.
-car can't build any real boost: doing a pressure check this weekend, as well as installing the new injector insulators (upper and lower), as they seem to be part of the issue
-when the car is warm, in 2nd, 3rd and 4th, when trying to give the throttle some go, at 3000-3500 RPM, the motor falls flat on its face
-the TB plate sticks
-when driving, taking my foot off the throttle, and leaving the car in gear, the car back/mis fires. Also noticed that when it fires out the back end, the WB is reading between 10-11. Seems to be connected
-idles high: ground and adjust idle according to manual
-BOV is constantly going off whenever I accelerate. It's an open atmosphere, and since I've never had an open atmo one before, not sure entirely how it should sound, but I definitely hearing a whirring noise from that area when accelerating.
colt45 gto
10-14-2010, 06:17 AM
it all sounds like a boost leak, the whole thing is connected.except the sticky butterfly, does it stick shut or open?
Hans@GZP
10-14-2010, 10:56 AM
What BOV are you running?
GRSHOPR
10-14-2010, 01:33 PM
It sticks shut. And it's an apexi open air bov. The guy claimed he didn't know the brand and said it was a recirculating.
More issues to add to the list above:
-It feels like when I shift, the exhaust hits the floor of the car. Time to get solid motor mounts?
-When I accelerate, my car sounds like a car with a broken exhaust. Like someone blowing a raspberry. When I stop accelerating, and just cruise, it has a deep mean sound. Thoughts on the farting noise? I have no cat, if that helps.
colt45 gto
10-14-2010, 07:19 PM
throttle stop is set wrong. or the cable is wrong.
bov is probably wrong for the car or its plumbed in wrong?, is the original hole bunged up in the pre turbo intake? its below the maf in the main pipe.
exhaust has broke at the flex with flexing, just fit new stock mounts, get a fresh flex weld that in or a new front pipe thats the farting noise. i'll bet the front and rear mounts are shot.
Hans@GZP
10-14-2010, 09:33 PM
To add to colt45's response. Also check the driveshaft carrier bearings. That could be what you are hearing/feeling on the floor of the car.
CCrunner84
10-14-2010, 11:01 PM
To add to colt45's response. Also check the driveshaft carrier bearings. That could be what you are hearing/feeling on the floor of the car.
It's a TT swap, he wishes he had carrier bearings :)
Did you check that leak from the rear turbo O2 housing? If you tightened it then that gasket is probably just blown. I'll make an attempt to drop that pressure checker off to you sometime friday night or saturday. Sunday morning my guests will be leaving, if your around I can come help you sort out these other issues.
-Nick
CoreyB
10-14-2010, 11:27 PM
Sounds like a winner, thanks elyria.
OK, so I'm bringing everything back to this thread. I've compiled a list of the symptoms of the car that need to be tuned, and if I have theories or steps I'm going to take on each one, I'll list them accordingly. If there are no ideas, I could use yours, guys, since I'm lost. I've never tuned my own car before.
-car can't build any real boost: doing a pressure check this weekend, as well as installing the new injector insulators (upper and lower), as they seem to be part of the issue
-when the car is warm, in 2nd, 3rd and 4th, when trying to give the throttle some go, at 3000-3500 RPM, the motor falls flat on its face
-the TB plate sticks
-when driving, taking my foot off the throttle, and leaving the car in gear, the car back/mis fires. Also noticed that when it fires out the back end, the WB is reading between 10-11. Seems to be connected
-idles high: ground and adjust idle according to manual
-BOV is constantly going off whenever I accelerate. It's an open atmosphere, and since I've never had an open atmo one before, not sure entirely how it should sound, but I definitely hearing a whirring noise from that area when accelerating.
This is your ignition timing being to advanced. Try rotating the CAS and see if it stops. Mine did the same thing after I rebuilt it. I still havent set base timing according to the manual. I just moved the CAS until the throttle responded well, had power and didnt do the rough off throttle thing you described.
GRSHOPR
10-15-2010, 12:50 AM
Thanks corey, I'll do that as a temporary stop-gap. Turning it counter clockwise is letting off it, right??
How tight/loose should the cable be?? Just want to make sure I have it correct.
I don't have a flex, it's an ATR dp with a cat elim, to a custom stainless 3' catback going to 4" mufflers. It hasn't broken at any of the joints either.
The BOV came with a 'T' fitting that has the lone branch of the fitting going to the bubble, but it's welded shut. The other straight through branches go from the y-pipe to the BOV.
As for the mounts, probably. I couldn't argue that, as I used the ones that came with the motor. A little bit of cracking at the 'tops' of the front and back if I recall, but nothing horrible.
Nick, I tightened the dp to the rear precat, to the point that I had a 3' breaker bar wrenching on it to tighten it. That damned thing better be sealed. And that gasket better not be shot. It's brand new.:rolleyes:
Hans@GZP
10-15-2010, 02:49 PM
Good call on the turbo conversion LOL. I didn't even pay attention to that part :p.
Just jack up the car and have it running. Put your hand by all of the exhaust flanges to feel for any exhaust leaks. Backfiring is usually caused by those.
CCrunner84
10-15-2010, 02:52 PM
Thanks corey, I'll do that as a temporary stop-gap. Turning it counter clockwise is letting off it, right??
How tight/loose should the cable be?? Just want to make sure I have it correct.
I don't have a flex, it's an ATR dp with a cat elim, to a custom stainless 3' catback going to 4" mufflers. It hasn't broken at any of the joints either.
The BOV came with a 'T' fitting that has the lone branch of the fitting going to the bubble, but it's welded shut. The other straight through branches go from the y-pipe to the BOV.
As for the mounts, probably. I couldn't argue that, as I used the ones that came with the motor. A little bit of cracking at the 'tops' of the front and back if I recall, but nothing horrible.
Nick, I tightened the dp to the rear precat, to the point that I had a 3' breaker bar wrenching on it to tighten it. That damned thing better be sealed. And that gasket better not be shot. It's brand new.:rolleyes:
There's a whole procedure on how to set the SAS screw (think that's what it's called), I know I used a feeler gauge etc when I cleaned up a throttle body. Hell, I have two in my basement if yours is giving you problems lol. I remember turning the CAS clockwise to advance the timing, counter to retard. I'll make sure and grab the timing light for Sunday, get it set right. Hell I believe you can pick one up dirt cheap at that farm and fleet for maybe 30 bucks.
CoreyB
10-15-2010, 03:37 PM
There's a whole procedure on how to set the SAS screw (think that's what it's called), I know I used a feeler gauge etc when I cleaned up a throttle body. Hell, I have two in my basement if yours is giving you problems lol. I remember turning the CAS clockwise to advance the timing, counter to retard. I'll make sure and grab the timing light for Sunday, get it set right. Hell I believe you can pick one up dirt cheap at that farm and fleet for maybe 30 bucks.
I agree with the use of the timing light. Make sure you ground the terminal by the battery to set base timing correctly.
GRSHOPR
10-15-2010, 04:39 PM
OK, so driving home, and CATASTROPHE. White smoke coming out my exhaust, from under the hood, through the vents, EVERYWHERE. Smells like kettle corn under the hood, but like crap out the tail pipe. No leaking fluids, coolant definitely still under pressure, and air puffing out near the rear precat. I took pics through my rearview mirror, they;re below. Please don't tell me head gasket.
http://i881.photobucket.com/albums/ac18/Hackurs/IMG_0351.jpg
http://i881.photobucket.com/albums/ac18/Hackurs/IMG_0349.jpg
GRSHOPR
10-15-2010, 04:42 PM
There's a whole procedure on how to set the SAS screw (think that's what it's called), I know I used a feeler gauge etc when I cleaned up a throttle body. Hell, I have two in my basement if yours is giving you problems lol. I remember turning the CAS clockwise to advance the timing, counter to retard. I'll make sure and grab the timing light for Sunday, get it set right. Hell I believe you can pick one up dirt cheap at that farm and fleet for maybe 30 bucks.
Thanks man. I read in the guide that they were like $100, and I was like no way. And I think the ignition timing is now on the back burner with the latest issue. *sighs*
CoreyB
10-15-2010, 04:43 PM
Sorry dude. How many times did you overheat it ? Pull the plugs and see if they have coolant on them.
GRSHOPR
10-15-2010, 04:55 PM
I never really over heated it. The hottest the coolant ever got was 220, and that was once. Gonna let it cool down, and then check the oil intake on the rear turbo, maybe do the plug tomorrow. If a bank did blow, it looks like it would be the rear, but it's got a brand new mls head gasket. What are the odds that it'd blow?
CoreyB
10-15-2010, 04:59 PM
I wouldnt think the odds would be high. Unless it wasnt torqued properly, head was warped, or surfaces were not clean enough.
GRSHOPR
10-15-2010, 05:04 PM
I double checked the torque, can't say as to warpage, but I definitely removed all the excess dirt and old gasket. It was very smooth and clean, double checked that as well. I guess I'll just have to wait til I pull the plug. But it's the rear bank, and I am emotionally drained by this car, so it's gonna wait at least til late tonight, if not tomorrow. Are there any other signs of a blown gasket?? Oil and coolant mixing?? Fluid leaks?? I just find it odd that there would still be pressure in the water neck if it was blown. Am I wrong on that?
GRSHOPR
10-15-2010, 09:05 PM
OK, so on a suggestion (thank you Nick), I checked out the rear turbo. That shit is F(&#@D up. Picking up a new one tomorrow. Thank god it wasn't a head gasket.
GRSHOPR
10-16-2010, 12:26 AM
When I replace the rear turbo, is there anything I should be looking out for or any maintenance and preventative measures I should be taking?
GRSHOPR
10-16-2010, 12:18 PM
Thanks Steve. I stripped it down to the short block when I rebuilt it, but I didn't want to take the pistons, rods, etc apart due to time. I hope that was enough.
GRSHOPR
10-24-2010, 05:45 PM
OK, so wound up going with a 9b that I found, and the car runs great. Smokes a little bit, but that's to be expected til the oil burns out of the exhaust. My next issues are that I can't turn down the idle past 1000 RPM's, and the one time that I got on it, it fell flat on its face. Not sure why. Didn't really try it after that, but it did hold normal boost when I asked for it. Thoughts on that cause?
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.