View Full Version : is my ecu fried?
futurevr4man
10-06-2010, 09:06 PM
my fuel trims are all set at 100% and do not change no matter what. even if i reset the ecu.
my 02 trim is set at 100% no matter what and does not change.
its acting like its in open loop constantly. is there a good way to tell for sure?
CoreyB
10-06-2010, 10:59 PM
Try unplugging the MAF and see if it changes.
SpdDmnVR4
10-06-2010, 11:20 PM
It didn't change it. He has been messing with the MAF-T and his new Ls6 mas all day. They haven't changed since the day the car first ran. less than 300 miles ago
futurevr4man
10-07-2010, 12:57 AM
less than 200 miles ago...
and yeah they have been set like that from the first time i turned the key. is it fried? is there a test i can do? i mean someone has to know the answer to this...
terrets
10-07-2010, 02:15 AM
You can pull it and look at the board....not sure if youll see anything though. Have OBD hooked up, not sure if that would tell you anything? Or possible a data logger that takes in ECU codes. Id think youd have a CEL though.
enigma
10-07-2010, 02:47 AM
I've had 2 go on me, have a look here!
http://www.stealth316.com/2-ecmremoval.htm
terrets
10-07-2010, 03:00 AM
^Nice adding the link enigma :).
futurevr4man
10-07-2010, 10:37 AM
its not throwing an engine code. i have a data logger and there is nothing.
the car has always run pig rich but it still ran OK with the 360's in it. now that i put in 550's i cant get it to do anything because they are just dumping too much fuel in there.
my question is just asking if there is a test i can do. obviously i can take it out and visually inspect, but is there anything i can try (checking voltage, current, or grounds) to see if i for sure have a bad ecu?
enigma
10-07-2010, 02:39 PM
If the car is a turbo, the turbo needle should go about halfway when you turn the ign on, if it does not move then it would be the ECU, as I said ealier I had 2 go on me, the ecu's dont like wet humid conditions, if the caps are leaking the humidity allows the acidic paste to spread on the board circuits.
SpdDmnVR4
10-07-2010, 02:45 PM
Do you mean the Load gauge(3rd gauge from L->R in the center dash) should go halfway up?
enigma
10-07-2010, 02:58 PM
I have a GTO twin turbo, I would imagine the US version would be the similar, on mine its the middle of the three gauges, boost and water, the boost needle goes about halfway when the ign is turned on.
CoreyB
10-07-2010, 02:59 PM
Yeah thats what he means. When the ECUs go in the 91-92 they will mess up the power supply, so when the key is on and not running instead of the needle resting in the middle at zero it may be pegged top, bottom or moving erraticaly.
Dont think this is your issue though. I am not a tuning expert by any means but If the the O2 sensor was bad could it set to 100% and the make the ecu stay at 100% fuel trim ?
mh3kgt
10-07-2010, 03:27 PM
I think on my MMCD it shows all 3 fuel trims at 100% all the time
SpdDmnVR4
10-07-2010, 03:36 PM
the o2 voltages oscillate like they should so its not a lazy sensor or anything, but I thought 100% trims that never change imply that the ECU is stuck in Open loop mode. But if that were true then the o2 voltage would be pegged all the time, I would think.
I have a 92 vr4 with 16T's(10 PSI) and my fuel trims are 82%, 101%, and 115% on completely stock fuel. I know trims are supposed to move and I know what the trims mean. But I wanna know what the stuck trims mean
futurevr4man
10-07-2010, 03:40 PM
to clarify, spddmnvr4 is my friend who is trying to help me get this figured out.
the "boost" needle sits at the half way mark with the key on. BUT i do recall once when it was pegged and another time when it didnt come up at all. seems fishy to me.
i am going to take the ecu out today and ill post some pictures. i have a 94, so i doubt i have leaky caps (its prevalent on 1st gen vr4's). but i will check anyhow and see whats up... it DOES NOT make any sense as to why my fuel and 02 trims are at 100% and everything else is normal. my car can hardly idle right now after the new injectors, i dont know what else it could be...
SpdDmnVR4
10-07-2010, 03:56 PM
91-97 cars all use the same Caps Nathan. So i can't say that I would be surprised if I saw a problem with yours. Mine were shot to hell and back. and my car is in good shape and only 2 years older than yours.
CoreyB
10-07-2010, 04:00 PM
Not true. They have the same value caps but in 91-92 they used rubicon brand caps. The seal on the bottom is prone to leaking. They got rid of those in 93 but they will still fail eventually. I have yet to see a 93+ ECU with leaking caps, sure they are out there though.
KeithMac
10-07-2010, 06:18 PM
If your tune is a mile out the ECU will have the wrong perceived LOAD, it won`t adjust the trims or go into closed loop if it believes the load is too high and it`s main factor in determining load is the Karman Hz signal from the air flow meter..
terrets
10-07-2010, 06:25 PM
I think on my MMCD it shows all 3 fuel trims at 100% all the time
Pretty sure my HHH shows 100% too on my stock 91 vr4
futurevr4man
10-07-2010, 06:35 PM
well i dont know what to do then.
if my ecu is working correctly, then why can my car barely idle? i put in the 550's, blow thru, and maft and i guarantee everything is set up correctly. but my car is terrible. like i cant drive it its so bad.
to my understanding my ecu's fuel trims as well as 02 trim should be changing. not staying at a constant 100%. my ecu may be getting a big load from the maf i have now (3.75" gm maf) but before when i had stock draw thru setup with the 360's the trims were still at 100% it just doesnt add up.
CoreyB
10-07-2010, 10:50 PM
Wonder if the TPS could be set wrong, so its never at the switch telling the ECU its at closed throttle.
futurevr4man
10-08-2010, 01:38 AM
i may look at that. although i feel its a stretch. it would be nice if thats all it was lol
KeithMac
10-08-2010, 07:10 PM
Befor condeming your ECU, fit the stock MAS. It sould be at least drivable with the 550`s in there just don`t got WOT for long as you`ll be massively overfueling..
steve
10-09-2010, 02:19 PM
If the car is a turbo, the turbo needle should go about halfway when you turn the ign on, if it does not move then it would be the ECU.
On all models the Check Engine Light should turn on for about five seconds when you first turn the ignition on. That's the ECU performing bulb test on power up. As you noted, the turbo models will move the factory boost gauge to zero until you start cranking and then back to zero when you stop if the engine doesn't start. While cranking it should move to the vacuum side of the scale.
futurevr4man
10-09-2010, 03:29 PM
as of now it seems i will try to mess around with my o2 sensors. the ecu is acting as it should except for the o2 trim and fuel trims... im not really sure what the issue is as of now.
although i bought a downpipe and new o2 sensor, we will see what happens. it seems i am just staying in open loop and never switching to closed loop which is causing me to run super rich 24/7
the check engine light does come on for 5 seconds, and my "boost" gauge (load meter lol) goes to zero when the ign is on, and then vacuum when cranking. everything is acting as it should except the fuel/o2 trims.
KeithMac
10-09-2010, 05:37 PM
You shouldn`t have to lean on the trims; if you`re running super rich your tune`s not right.. The ECU won`t go into closed loop if you`re that far out to begin with.
futurevr4man
10-09-2010, 09:49 PM
well when i had stock mas on it, the o2 trims and fuel trims were still at 100%. and that has nothing to do with my tune, thats 100% ecu... im not jumping to conclusions, i have thought a lot about it
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.