PDA

View Full Version : 3.5 Pampena Stroker DR750 Build



Chris@Rvengeperformance
02-24-2014, 10:53 PM
I'm blew my engine last June turning up the boost on e85. I knew I wanted to go with one of Ray's engines, and after a while I ended up going the route of the 72 stroker. Here are the build specs

1)6G72/6G74 based stroker from Pampena Motorsports
2)BC Rods
3)Ray's custom Ross Forged Pistons for the stroker (92mm bore) + Pampena Tool Steel Wrist Pins
4)stock head rebuild
5)DR750s with 11 blade titanium turbine
6)Chrome ecu
7)Evo maf (for now)
8)FIC 1050 low impedence injectors
9)Walbro 415 E85
10)New stock gaskets and headbolts, oem new water pump, oil pump, hydraulic tensioner, gates regular belt and new pulleys
11)ETS Fmic
12)Tanabe Touring Medallion Exhaust
13)DN Performance o2/downpipes, knockoff tanabe downpipe
14)IPS Oil Pan and Setrab Oil cooler
15)AEM inline wideband
16)Defi Racer Oil, Boost, Water gauges
17)3sx single pass radiator
18)New oil feeds
19)5 Speed swap, 300m output shaft, billet main and mid cases on transfercase
20)ACT MB019 heavy pressure plate and southbend clutch stage 4 FE clutch disc

The bore is kept small to promote head gasket seal. It isn't like I need a ton of displacement with these turbos anyway.

There are probably more mods, but those come to mind at the moment. I'll edit the post if I think of anything else relevant. Pretty nervous getting started just because that is a big pile of parts that could go up in smoke, so just going to be careful and slow. Haven't done a whole lot so far:

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_54723SA5_6LDD.JPG

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5465zgG8_N85p.JPG

Ray's cylinder finish and pistons are very nice. Block and heads did not need decking and it keeps the cam timing right if you don't.

Trying to setup a comfortable clean place to work:

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5467ff5g_oy78.JPG

Getting the head bolts and washers ready:

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_54747lb7_rVlo.JPG

That's about it for now. Should get the heads on tomorrow. I don't have a lot of time to work in the evenings, so things may move slowly. The freight company must have moved this around out in the rain because there was some flash rust on the front where the oil pump mounts, but it cleaned up. Just took some time.

CoopKill
02-24-2014, 10:57 PM
Woot, in for the awesome!

Uniuno
02-24-2014, 11:18 PM
Very exciting! This is my dream build right here, I'm looking forward to seeing what it can do.

mb3000
02-24-2014, 11:28 PM
Been waiting for this one, subscribed!

TurboSinceBirth
02-25-2014, 12:06 AM
I'm interested in seeing the progress with flashed ecu on a noisy forged motor. I have a 93mm Pampena 72 stroker I'm tempted to swap in with TD04s after one last go on the stock motor. So far Todd can't get his tuned right with the flashed ecu.

thor'svr4
02-25-2014, 12:13 AM
Spool monster!!!

Chris@Rvengeperformance
02-25-2014, 01:16 AM
I'm interested in seeing the progress with flashed ecu on a noisy forged motor. I have a 93mm Pampena 72 stroker I'm tempted to swap in with TD04s after one last go on the stock motor. So far Todd can't get his tuned right with the flashed ecu.

If I get pissed and can't solve it I'll disable the damn thing, not like it is going to save me on e85 anyway.

Chris@Rvengeperformance
02-25-2014, 01:19 AM
Well I had the block cleaned really good on the front, totally lint free. Cleaned it with brake cleaner, then mineral spirits, then alcohol. So, I threw the head on to keep from having to clean it again:

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5475hF05_4O6Q.JPG

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5476Rd59_5NX7.JPG

Then to keep the dirt out and for some encouragement:

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5479QHoy_569u.JPG

A LOT more room in my shop now:

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5477g3cp_939X.JPG

Chris@Rvengeperformance
02-25-2014, 01:37 AM
can someone fix my spelling in the thread title? thanks

Jimvr4
02-25-2014, 01:52 AM
I'm "stoked" to see this finally happening :)

kywhitelightning
02-25-2014, 02:41 AM
In for progress. Good to see you're finally moving forward. Good luck buddy.

Jeff

oohnoo
02-25-2014, 05:31 PM
Good luck with your build, it's going to an exciting year for DR750's :)

Your joking right? Hate to show you mine....no homo...lol





Trying to setup a comfortable clean place to work:

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5467ff5g_oy78.JPG

oohnoo
02-25-2014, 10:18 PM
Ummm think you took that the wrong way...Here's my garage, would love on like yours.

http://i301.photobucket.com/albums/nn61/oohnoo_VR4/2012-05-09172607.jpg (http://s301.photobucket.com/user/oohnoo_VR4/media/2012-05-09172607.jpg.html)


Sorry the floors are not marble with a granite workbench, but yeah its clean in there. I would've coated the floors, but didn't want to have my car sitting outside that long unregistered and disabled.

Chris@Rvengeperformance
02-25-2014, 10:35 PM
Ummm think you took that the wrong way...Here's my garage, would love on like yours.

http://i301.photobucket.com/albums/nn61/oohnoo_VR4/2012-05-09172607.jpg (http://s301.photobucket.com/user/oohnoo_VR4/media/2012-05-09172607.jpg.html)

haha sorry! had a troublesome day.

mehrshadvr4
02-26-2014, 03:05 AM
Didn't Matt put Dr750s on his stroker?

familyMAN
02-26-2014, 09:06 AM
Yes he did

J. Fast
02-26-2014, 11:00 AM
Didn't Matt put Dr750s on his stroker?

Yes he did. He put down 480whp uncorrected at 21psi on pump/meth injection.

green-lantern
02-26-2014, 11:11 AM
Hell yeah! Can't wait to see this come together.

I can't tell from the pics but don't forget to put in the knock sensor before bolting the heads down. Also that thing is going to spool very fast, are you worried about the same outcome as before? I'm sure this bottom end is much stronger but wasn't the conclusion last time flattened bearings? Sorry if I got that wrong, it's been a while since I've read your other thread.

Good luck buddy, I hope to see it at NG


Edit: BTW I'm not even going to post a pic from my garage. lol

Chris@Rvengeperformance
02-26-2014, 11:22 AM
Hell yeah! Can't wait to see this come together.

I can't tell from the pics but don't forget to put in the knock sensor before bolting the heads down. Also that thing is going to spool very fast, are you worried about the same outcome as before? I'm sure this bottom end is much stronger but wasn't the conclusion last time flattened bearings? Sorry if I got that wrong, it's been a while since I've read your other thread.

Good luck buddy, I hope to see it at NG


Edit: BTW I'm not even going to post a pic from my garage. lol

Yeah, my knock bracket is in the mail at the moment. If it doesn't make it in this week I may put it together anyway and either switch to allen bolts on the knock bracket or build a tool to tighten them. I think I can modify a socket enough to make it work. OR I can drive 3 hours round trip and pick one up off a spare block I have back at my parents. I don't feel super great using RTV with the temps I'm seeing. I'd rather see it get to 55 or 60, so I may just wait for a bit anyway since I can't put the pan on or anything that needs it.

Not really worried about it failing like it did. I've pulled a lot of timing all around the map to start out with. I've also on Ray's recommendation went to a lot colder spark plug.

Also, without knowing the history of the last shortblock it is hard to come to a firm conclusion of the failure. After the heads were cleaned up you can see tiny detonation specks in them that suggested in the past the engine experienced detonation. It had 95K miles on it and I know jrod raced it, so the mains could've been just ready to go. I also found what appears to be a nitrous or aftermarket rev limit pill under the seats when I took them out. Little white pill that says 6800 on it. Who knows what they can't from! Could've fell out of his pocket or could've been something on this car at some point in time.

I hope to see it at the NG too, I don't think I'm going to push it hard until I get some fun time in it. I'm also going to religiously document the oil pressure, cut the oil filters open after every tuning day, etc. Basically try to be really careful. Thinking about getting it on a dyno.

I'm not wanting to waste all these parts, but 400AWHP sounds like more fun than zero at the moment. We'll see what it does on wastegate and go from there.

HLxDrummer
02-26-2014, 11:35 AM
Any plans to dyno tune it? Seems like a good/safe investment.

Anyhow, good luck! Looking forward to seeing it on the road.

green-lantern
02-26-2014, 01:38 PM
Yeah, my knock bracket is in the mail at the moment. If it doesn't make it in this week I may put it together anyway and either switch to allen bolts on the knock bracket or build a tool to tighten them. I think I can modify a socket enough to make it work. OR I can drive 3 hours round trip and pick one up off a spare block I have back at my parents. I don't feel super great using RTV with the temps I'm seeing. I'd rather see it get to 55 or 60, so I may just wait for a bit anyway since I can't put the pan on or anything that needs it.


I forgot it on one engine but was able to bolt the plate down with a universal. I know I got it pretty tight but I wasn't real happy that I wasn't able to use a T-wrench. The sensor itself was a bit tricky lol. I'd wait if I was you. With all these awesome parts I’d want everything just right.

Chris@Rvengeperformance
02-26-2014, 10:48 PM
What's the current opinion on shimming the oil pump?

sergechronos
02-26-2014, 11:29 PM
I went back and forth on the idea of doing it, but decided against it. A new OEM pump with new bearings should be just fine and too high of oil pressure could be as bad as too low IMO. Not sure how much difference it might make though so I'll let the heavy weights come in here with their opinion. Weren't the TOGA oil pumps shimmed? At any rate, if I were to do it, I wouldn't do a very big shim.

green-lantern
02-27-2014, 09:07 AM
I think the consensus is not to do it. If I’m not mistaken there was other problems that arose from doing it. It’s been a while since I’ve looked into it though.

Chris@Rvengeperformance
02-27-2014, 11:16 PM
nothing super special here, but got a few things done:

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_54938jIt_Oyvr.JPG

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_54979XFn_x3pJ.JPG

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5499o18F_wwyu.JPG

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5502Y02O_8mQ3.JPG

CoopKill
02-27-2014, 11:25 PM
Is that aluminum tape on the intake ports?

Chris@Rvengeperformance
02-27-2014, 11:34 PM
Is that aluminum tape on the intake ports?

Yes, just to keep junk out.

CoopKill
02-28-2014, 12:38 AM
Great idea! I have some laying around. Much stickier than blue tape!

NOMIEZVR4
02-28-2014, 03:08 PM
ahem...you mind listing the $$ you've spent? :p

That would really put things into perspective...

sergechronos
02-28-2014, 03:14 PM
ahem...you mind listing the $$ you've spent? :p

That would really put things into perspective...

Pretty sure this is the automotive equivalent of asking a woman how old she is.

Sent from my XT1080 using Tapatalk

NOMIEZVR4
02-28-2014, 03:18 PM
Pretty sure this is the automotive equivalent of asking a woman how old she is.

Sent from my XT1080 using Tapatalk

Mine doesn't mind...shes always been down for anything..:D

Chris@Rvengeperformance
02-28-2014, 03:32 PM
ahem...you mind listing the $$ you've spent? :p

That would really put things into perspective...

haha no way I'm going to add that all up. Rough estimates with the car price probably would almost buy a new evo x.

Let's say that the budget is gone for a year or two. If it blows up now it has to sit.

NOMIEZVR4
02-28-2014, 03:49 PM
I've got nearly 20k into mine too including the cost of the car and all...:( I purchased the car for under 4...phucking money pits..

Jimvr4
02-28-2014, 03:51 PM
Hey nice work :bigthumb:

I didn't add mine up either. Not expecting mine to go wrong with my modest power goals. You guys running E85 scare the crap out of me. I have no idea how you figure out what a safe tune is. It just seems like every build starts out so great with all kinds of amazing VD graphs and then something spins or blows up. I just want to enjoy a 400+ WHP street car and not worry :p

CoopKill
02-28-2014, 04:10 PM
40k +

Sent from the Man Cave!

*\( ^o^ )/*

Chris@Rvengeperformance
02-28-2014, 07:33 PM
This is a noob question, but I have never had forged pistons before. Do I need to be extra careful warming the car up? Normally I let the car idle for maybe 10-20 seconds, then just drive gently, keeping it under 3000 and low boost until it gets up to maybe 130 degrees or so, then I will drive slightly more aggressively, maybe taking to 4000. I never go WOT or over 4500 until it is at operating temp.

Will that still work or should it be idled longer?

kywhitelightning
02-28-2014, 07:40 PM
Sounds like a good plan. I called Ross when I put mine together and asked them about the extra clearance I thought I had and the rep said that was the correct clearance and to do exactly as you stated. Let the engine warm up a little prior to pushing it.

Edit: You can drive it just don't run boost until warmed up.

Jeff

Chris@Rvengeperformance
03-12-2014, 02:03 AM
some progress I made last Sunday and tonight:

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5506oy25_hzCu.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5508J1jO_2p7K.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_55099LZ2_2D1U.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_55104jaE_1j84.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_55189A9f_wlKb.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5569N391_8006.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5570U01w_C734.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5573tPw4_Ra23.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5574xzc8_fSgJ.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5575g2rQ_OzVF.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5578pdTu_NNEp.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5582IqA6_2BK4.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5584b3F8_9sP6.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5585ce2K_ZO62.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5587j4ko_rdO1.JPG

I cleaned the oil pan up last fall, but I wanted to double check it again, it is a good thing I did. I cleaned it literally for an hour before I could quit finding anything. A magnetic drain plug helped. I hope I got everything, the trap doors in the IPS pan make it hard to clean. Everything else went well. Oh, the stock timing covers are on just to keep my clear ones from being scratched when I install the engine.

Taking a short vacation this friday through early next week, so probably won't get it in the car until after I get back.

CoopKill
03-12-2014, 02:34 AM
Very nice!

Sent from the Man Cave!

*\( ^o^ )/*

familyMAN
03-12-2014, 02:37 AM
Beautiful. Engine deserves some nice cam gears and clear covers.

kywhitelightning
03-12-2014, 04:53 AM
some progress I made last Sunday and tonight:

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5584b3F8_9sP6.jpg

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5587j4ko_rdO1.JPG

I cleaned the oil pan up last fall, but I wanted to double check it again, it is a good thing I did. I cleaned it literally for an hour before I could quit finding anything. A magnetic drain plug helped. I hope I got everything, the trap doors in the IPS pan make it hard to clean. Everything else went well. Oh, the stock timing covers are on just to keep my clear ones from being scratched when I install the engine.

Taking a short vacation this friday through early next week, so probably won't get it in the car until after I get back.

I see you used red RTV on the cam seals and caps, have you used it before without issue? I only ask because I always thought red was for high temp and black was for oil. I have used grey before with oil and it seals great but is like cement when cured. Red has always been more pliable on the applications I have used it for.

Looks great and I'm really diggin the water neck.

Edit: Are those 9 blade turbines I spy?

Jeff

Chris@Rvengeperformance
03-12-2014, 10:05 AM
I see you used red RTV on the cam seals and caps, have you used it before without issue? I only ask because I always thought red was for high temp and black was for oil. I have used grey before with oil and it seals great but is like cement when cured. Red has always been more pliable on the applications I have used it for.



Looks great and I'm really diggin the water neck.



Edit: Are those 9 blade turbines I spy?



Jeff




I've had really good luck using the red rtv on the oil pans, so I can't see why it wouldn't work. It isn't doing a lot in this case anyway, I only used it on the corners of the cam caps for the valve cover, and lightly around the cam end plugs. It doesn't look that pretty, but most of it is going to get covered once it is in the car.

I've done oil pans with gray that didn't harden for some reason and leaked, so I quit using that.

I actually used the right stuff on the pan this time, it is a lot easier to apply to a large area. I get worn out squeezing the stupid rtv tube. The right stuff is pressurized.

They are actually the original 11 blade turbines my turbos came with. Matts guys did a full rebuild on them, so it all looks new.

Thanks on the water neck, a smooth finish only works on stuff like that if you can media blast it first. The water necks are a real pita to prep by hand. I just scuffed and cleaned it as best I could. You could paint dirt with thevht wrinkle paint and it would look good. It is super tough too. I dropped the front valve cover on the concrete floor top down and it didn't lose any paint. I have seen powdercoat that was weaker.




Sent from my RM-845_nam_vzw_100 using Tapatalk

Chris@Rvengeperformance
03-12-2014, 10:07 AM
Beautiful. Engine deserves some nice cam gears and clear covers.




I want some small BC cams at some point. I do have clear covers, should've painted my cam gears though, they look really dingy against everything else now.





Sent from my RM-845_nam_vzw_100 using Tapatalk

green-lantern
03-12-2014, 11:37 AM
I see you used red RTV on the cam seals and caps, have you used it before without issue? I only ask because I always thought red was for high temp and black was for oil. I have used grey before with oil and it seals great but is like cement when cured. Red has always been more pliable on the applications I have used it for.



Jeff

I use black also but the main reason is I HATE to see the red squishing out of my valve covers. When I looked at Chris's I sort of snarled a bit, lol. Not to give you a complex though Chris.

Chris@Rvengeperformance
03-12-2014, 12:07 PM
haha yeah I know it looks kinda crappy, I'll get out the magic marker for you ;)

green-lantern
03-12-2014, 12:10 PM
:bigthumb: It's my OCD kicking in, it get's worse the older I get :runaway:

sergechronos
03-12-2014, 12:52 PM
Thanks on the water neck, a smooth finish only works on stuff like that if you can media blast it first. The water necks are a real pita to prep by hand. I just scuffed and cleaned it as best I could. You could paint dirt with thevht wrinkle paint and it would look good. It is super tough too. I dropped the front valve cover on the concrete floor top down and it didn't lose any paint. I have seen powdercoat that was weaker.


Don't think Media blast even covers it. I smoothed and sanded mine down as much as I could (going to be doing AN fittings them painting/powder coating it) and I probably have well over 10 hours invested in it. In retrospect, just saying screw it and doing the wrinkle likely would've been a better idea and looked more OEM. Yours definitely turned out nice

familyMAN
03-12-2014, 01:10 PM
What wrinkle paint are you using? I've been contemplating doing my intercooler piping.

Chris@Rvengeperformance
03-12-2014, 01:26 PM
What wrinkle paint are you using? I've been contemplating doing my intercooler piping.

Amazon.com: VHT SP201 Wrinkle Plus Black Coating Can - 11 oz.: Automotive (http://www.amazon.com/VHT-SP201-Wrinkle-Black-Coating/dp/B000CPIMXK/ref=sr_1_2?ie=UTF8&qid=1394641580&sr=8-2&keywords=vht+wrinkle+plus)

Do like the instructions say. 3 coats. 1 horizontal. 2nd coat 90 degrees to the last one, 3rd coat at a diagonal.

Other wise it does not wrinkle evenly. It works better on flat surfaces. I had issues getting a perfect coat on my intake pipes, but they are good enough. Also, if you retouch it, you have to do 3 coats or it won't be wrinkled in the touched up spot. Also, if you put it on too thick it makes crazy deep wrinkles that take like 2 months to dry. I'm making it sound harder than it is though...

familyMAN
03-12-2014, 02:58 PM
Thanks. I have a can of it but it didn't wrinkle up. Was pretty darn cold in garage when I tried it though.

Chris@Rvengeperformance
03-12-2014, 03:02 PM
Thanks. I have a can of it but it didn't wrinkle up. Was pretty darn cold in garage when I tried it though.

when it is cold I have seen it take 2 days to wrinkle. heat gun helps.

Kyoshosp2
03-13-2014, 01:08 AM
That a pearl white Stealth ?


Sent from my iPhone using Tapatalk

vr4tune
03-13-2014, 06:51 AM
That a pearl white Stealth ?



Yes..

CoopKill
03-13-2014, 12:11 PM
Yes..WTF you doing replying at 3am?

Chris@Rvengeperformance
03-13-2014, 12:20 PM
yup:

http://www.chrisbehnken.com/Images/photos/CarMove/IMG_523480k9_tmu8.JPG

KeithMac
03-13-2014, 04:14 PM
Lovely job !, don't know if I'm more jealous of your engine or your garage ;).

I use black Suzuki three bond black for sealing anything engine related, it's expensive for a tune but lasts for ever.

If you've had good results with the red sealant no reason not to use it, I'd take no oil leak over looking nice ever time!.

vr4tune
03-14-2014, 02:15 AM
WTF you doing replying at 3am?

2:51 don't exaggerate.

vr4tune
03-14-2014, 02:17 AM
yup:

http://www.chrisbehnken.com/Images/photos/CarMove/IMG_523480k9_tmu8.JPG

Sexiest pearl stealth ever!!!!!!

love the rounded 99 corner lights and 96 wing.

futurevr4man
03-15-2014, 02:59 PM
whos the hobo in the lumberjack jacket??

green-lantern
03-15-2014, 05:39 PM
whos the hobo in the lumberjack jacket??

:heehee:

Chris@Rvengeperformance
03-15-2014, 07:01 PM
Hahaha makes me look twice as big

Sent from my RM-845_nam_vzw_100 using Tapatalk

whitedragon
03-16-2014, 09:57 PM
Hahaha makes me look twice as big

Sent from my RM-845_nam_vzw_100 using Tapatalk

That's what she said...

...but it looks hella nice.

Chris@Rvengeperformance
03-16-2014, 10:00 PM
Yeah she did...

Sent from my RM-845_nam_vzw_100 using Tapatalk

JasonY
03-16-2014, 10:15 PM
You're really gonna like this setup. Power is as instant as 9b's and the bigger engine sounds incredible. Hearing a 3L run next to todds 3.5(identical exhaust setup on both) makes the 3L sound like a little bitch.

Jason

Chris@Rvengeperformance
03-16-2014, 11:40 PM
Compared to my 275k mile 4 banger ranger I'd guess it'll be a hoot :)

Sent from my RM-845_nam_vzw_100 using Tapatalk

Chris@Rvengeperformance
03-21-2014, 12:55 PM
Installing rear main

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5486Fc.jpg?635309955424849033

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5487hR.jpg?635309955424693043

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_5491KD.jpg?635309955424537053

My amazing trans install rig

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6314ko.jpg?635309955424537053

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6318Fk.jpg?635309955424069083

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6320NL.jpg?635309955423913093

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6329LX.jpg?635309955423913093

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6331lJ.jpg?635309955423757103

Chris@Rvengeperformance
03-21-2014, 12:56 PM
turning hoist around
http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6341Cc.jpg?635309955423601113

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6350JD.jpg?635309956884135483

Squirt wanted to help:

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6351as.jpg?635309956884135483

trying from the side (only didn't work because of jackstand interference, managed to slide around to the front (yes, you can install engine from front in 22 feet deep garage, but barely)

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6352NA.jpg?635309956883979493



http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6354DP.jpg?635309956883979493

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6357LQ.jpg?635309956883667513

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6360qe.jpg?635309956883511523

Chris@Rvengeperformance
03-21-2014, 12:56 PM
http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6361HT.jpg?635309956883355533

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6362Wq.jpg?635309956883355533

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6367sY.jpg?635309956883043553

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6368kf.jpg?635309956882887563

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6370vv.jpg?635309956882575583

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6372yh.jpg?635309956882107613

http://www.chrisbehnken.com/Images/photos/2014Engine/IMG_6373gi.jpg?635309956881951623

futurevr4man
03-21-2014, 01:34 PM
Nope, looks like crap. Take it out and restart.

Chris@Rvengeperformance
03-21-2014, 01:36 PM
Nope, looks like crap. Take it out and restart.

damn do I have to tear it down to the shortblock again :(

green-lantern
03-21-2014, 02:24 PM
Awesome

Do you actually own the correct tool for doing the main seal? lol

Also whos the guy giving you a hand?

Greg E
03-21-2014, 02:40 PM
Where is the umbrella?!?

Chris@Rvengeperformance
03-21-2014, 03:12 PM
Awesome

Do you actually own the correct tool for doing the main seal? lol

Also whos the guy giving you a hand?

yeah, I found one super cheap on ebay one time, so might as well.

The other guy is kyle, aka Hellaflush.

Hellaflush
03-21-2014, 03:13 PM
Awesome

Do you actually own the correct tool for doing the main seal? lol

Also whos the guy giving you a hand?

o/ That'd be me

Chris@Rvengeperformance
03-21-2014, 03:14 PM
Where is the umbrella?!?

that's over my head, I don't get it?

Greg E
03-21-2014, 03:29 PM
that's over my head, I don't get it?

http://s17.postimg.org/8md5nej5b/image.jpg

Chris@Rvengeperformance
03-24-2014, 02:53 PM
has anyone ever seen the numbers of the plastic timing cover being a little off to the crank pulley mark? I have double and triple checked the timing cog pulley and it is lined up to the dot on the face and the indent on its back side to the oil pump perfectly, but when the crank pulley is on the tdc mark lines up 2.5 to 5 degrees off from the TDC mark on the plastic cover.

I just noticed this when I was double checking the timing before cranking it over to prime it. The only thing I can see is maybe the plastic covers can shift a little in the bolt holes when you install them. I haven't timed a 2G engine for almost 10 years, but I'm 99.9% confident it is timed right.

sergechronos
03-24-2014, 03:09 PM
Possibility the timing cog is from a 1g? Believe the cogs are one tooth different. Not sure if it'd be enough to throw the crank pulley that far off, but only thought I've got ATM.
Did you confirm piston is at TDC with the cog on the mark?

Would highly doubt the bolts could allow the covers to shift that much.

Sent from my XT1080 using Tapatalk

familyMAN
03-24-2014, 03:13 PM
Yes there can be variance in any of those components. I checked TDC with a piston stop and my crank gear to oil pump slot is off a couple degrees. I believe my balancer to timing cover is the same amount off as the oil pump to crank gear but I could see that any of those could be off a little bit. Use a piston stop and figure out true TDC and remark your balancer.

CoopKill
03-24-2014, 05:51 PM
I found the piston tdc with a screwdriver, then checked the oil pump to crank gear which was dead on. The balancer/plastic is off between 1-1.5 teeth.

Jimvr4
03-24-2014, 05:56 PM
I agree. I found the balancer and plastic cover had some slop in them. I feel the marking there is just ballpark - not accurate enough to use to time the engine but good enough to see if anything is WAY off.

Chris@Rvengeperformance
03-25-2014, 01:12 AM
Thanks for the input guys. I pulled the crank pulley again to double check and the timing cog is right. Cams are lined up perfect still, going to call it good.

We got quite a bit done sunday:

1)engine wiring
2)starter + wiring
3)all the engine mounts torqued
4)battery + battery mount
5)clear cam covers are on
6)checked cam timing 3-4 times lol
7)shifter cables
8)clutch slave cylinder
9)power steering pump
10)a/c compressor
11)turbo coolant lines (I was waiting on cherry hill for some new ones, but gave up. I ordered like 2 weeks ago and not even any tracking! Re-used the old ones as I was really careful removing them, but I am sure they will leak with my luck) I don't like using generic line because it seems to not last nearly as long as oem.

Didn't do a whole lot tonight, really tired, but the good news is the motor makes 40+ psi of oil pressure with the plugs out and 35+ with them in, each with maybe 10 seconds on the starter. It was still climbing but I don't want to wear out the starter for no reason. Cam lobes are slick and wet with new oil, so top end is getting lubed well as well. Sounds healthy cranking. For some reason the battery was dead, I had it on the tender for a while a month or two ago and it seemed to be holding just fine all winter, but was down to 3 volts all of a sudden. After cranking for 7-8 seconds it starts to slow down a bit even after charging, so a new battery may be needed. I'll probably go back to a group 51 like I ran before to save a little weight, but still have a good sized battery.

Have some things to do yet, but going to take my time and get everything right:

1)Front axles
2)Trans fluid
3)Transfercase
4)downpipe
5)intercooler main cold pipe and 2 hot pipes
6)radiator
7)plenum + throttle body
8)probably forgetting some minor stuff
9)accessory belts
10)intake piping + maf + air filter
11)flash updated tune

shouldn't really take too long, but it is a little finicky getting the lower intercooler hot pipe on the front turbo and under the a/c compressor without rubbing things.

Oh, I will also have to show how I "enhanced" oohnoo's crank tool. Drill out the little hole in the hand that is supposed to be for hanging it on the wall to about 3/8". Now grab a 3" 3/8 or 10mm bolt and stick it through the hole. You can now rest the tool against the driver side lower cross member and the bolt stops it from turning so you can easily torque the crank bolt by yourself.

CoopKill
03-25-2014, 01:45 AM
Thanx for the crank tool mod!

Chris@Rvengeperformance
03-30-2014, 11:24 PM
Fired it up today. Sounds good, lifted tick of course, but no bottom end noises I can hear.

I let it warm up. 22 inches of vacuum at 850 rpm. 32 psi oil pressure.

No obvious issues, but tomorrow I'll drain the oil and cut the filter apart to inspect.

Sent from my RM-845_nam_vzw_100 using Tapatalk

green-lantern
03-31-2014, 10:49 AM
No 1st time start up vid?

Chris@Rvengeperformance
03-31-2014, 10:53 AM
No 1st time start up vid?

I got one, but its really nothing impressive. I didn't prime the fuel pump first because I wanted to give the engine even more opportunity to pickup oil pressure before it started, so it took two tries. Plus my goofy self with a shit eating grin is all over it, but maybe I'll post it later :)

green-lantern
03-31-2014, 11:25 AM
I got one, but its really nothing impressive. I didn't prime the fuel pump first because I wanted to give the engine even more opportunity to pickup oil pressure before it started, so it took two tries. Plus my goofy self with a shit eating grin is all over it, but maybe I'll post it later :)

:lo5l: I bet, I'd be grinning also if I just fired up my Pampena stroker.

NOMIEZVR4
03-31-2014, 11:43 AM
congrats on the startup....

Chris@Rvengeperformance
04-01-2014, 02:18 PM
So far so good, I only have about 15 miles on it because the license is expired at the moment, but it is running great. After fully warmed:

850 rpm idle
21-22 inches of vacuum
26-27 psi of oil pressure
no smoke, no noises, no piston slap on startup
no major leaks
runs really strong, the extra displacement makes a big difference. There is a lot of torque at 2000 RPM. So far, my FMIC surging is gone :crosses fingers:

I cut the filter open last night after the first warm up start on sunday and there was BARELY anything in it and the oil was clean, no sparkles, you could have believed it came out of the bottle, other than the hint of assembly lube.

very happy so far. just need to get it licensed. then put 100 miles on it and change the oil again, then probably run it 500-1000 more miles.

oh btw, with temps in the 50s or so in the mornings I think it needs a little more cranking IPW on the e85. Takes a try or two to get it to start, I made a change, but won't know until it cools off again. Warm start is just fine. I bet next winter I'll have to add quite a bit of fuel at startup.

Greg E
04-01-2014, 02:23 PM
If warm start is good, only play with the cranking IPW in the lower temp ranges.

Chris@Rvengeperformance
04-01-2014, 02:45 PM
yup, the 68 degree row is all I changed for the moment

Jimvr4
04-01-2014, 02:50 PM
Great to hear. My oil was the same - looked as clear as fresh oil from the bottle.

On another note I was googling for instructions on setting the date for my Omega Constellation and guess whose name came up on a forum posting :suspect:

HLxDrummer
04-01-2014, 04:29 PM
Awesome, I'm happy for ya! Sounds like great vacuum and oil pressure!

familyMAN
04-01-2014, 10:33 PM
Good news! That vacuum is too high....you need more cam:D

sergechronos
04-01-2014, 10:35 PM
Good news! That vacuum is too high....you need more cam:D

I like the way this man thinks! Someone get him a promotion!

Sent from my XT1080 using Tapatalk

kywhitelightning
04-02-2014, 03:40 AM
Great job getting it back running Chris. Now get it tuned up and reaady for NG.

Jeff

Toni
04-02-2014, 12:37 PM
Great work!! NG should be a blast this year :)

Chris@Rvengeperformance
04-05-2014, 05:25 PM
Well I put a few more miles on it today, it is at 25 total. Runs great except the cold starts. Apparently I went the wrong way, it needed less fuel. Hopefully I have it solved, but it is hard to tell since it needs to sit overnight for a good test and I don't want to start it unless I'm going for a drive.

Oil pressure is still the same and I did a compression check on the front 3. Engine was down to 160 degrees by this time, it had been sitting an hour or so, so the results right after shutdown may be higher, but looks pretty good so far.

1 3 5
155 152 160

Hopefully #3 will come up a hair, but not bad for 25 miles I'd say.

kywhitelightning
04-05-2014, 07:37 PM
What is the static compression ratio?

Jeff

Chris@Rvengeperformance
04-05-2014, 08:01 PM
The standard 8:1

Sent from my RM-845_nam_vzw_100 using Tapatalk

KeithMac
04-06-2014, 10:22 AM
Nice to see it's running :), probably the best combination of engine and turbos you can get for a very fast street 3s.

Will you be running it down the strip this year?.

Chris@Rvengeperformance
04-06-2014, 11:57 AM
Nice to see it's running :), probably the best combination of engine and turbos you can get for a very fast street 3s.

Will you be running it down the strip this year?.




I very much hope so. Not going to smash any records, but an 11 would be a nice start.





Sent from my RM-845_nam_vzw_100 using Tapatalk

kywhitelightning
04-06-2014, 03:04 PM
11's pffffffff. Question is how deep in the 10's will it be capable of. Of course, it needs to be leaned on to get there but you definitely have the hardware.

Jeff

Chris@Rvengeperformance
04-06-2014, 03:07 PM
11's pffffffff. Question is how deep in the 10's will it be capable of. Of course, it needs to be leaned on to get there but you definitely have the hardware.

Jeff

baby steps :)

Chris@Rvengeperformance
04-06-2014, 06:00 PM
not a great sign, fluid coming out of my transfer case looks like silver paint. When I installed it I noticed shitty looking fluid in it and tried flushing it a bunch. It looks better now than it did. I'm going to change it a time or two again, but if it doesn't clear up it is going to have to go back to ray.

Weird thing is it looks like aluminum...

Chris@Rvengeperformance
04-06-2014, 06:06 PM
oh and fittings at oil cooler to filter housing are leaking. I can never get these things to be bone dry! New oem washers, new an adapters and the ips lines. I was able to tighten it up so more, but will have to put some miles on and see. also seems like the oil filter may be seeping a bit at the o-ring. I can never seem to get that to not leak a tiny bit either, it is weird. Oil filter housing looks good and I just tighten the filter up by hand, I don't see how I could screw that up.

pan and returns and heads are all dry, so at least the labor intensive stuff looks good so far. trans is dry. 4th feels like shit going in, so I think the shifter rods are hitting the intercooler pipe.

green-lantern
04-07-2014, 10:09 PM
It's like a Harley, just marking some territory.

green-lantern
04-07-2014, 10:49 PM
Or like the blackbird, not happy and sealed until it's hot and hauling ass :D

http://static.flickr.com/1242/1417846404_a3f278396e_o.jpg

Chris@Rvengeperformance
04-08-2014, 10:57 AM
the car does not like starting in 40 degree weather on summer e85. I've tried to tune, but haven't dialed it in yet. I can get it to start, but takes a couple tries and some prodding. Then it is fine the rest of the day.

familyMAN
04-08-2014, 12:59 PM
More fuel. Dump it when below 50ish.

Chris@Rvengeperformance
04-08-2014, 01:08 PM
More fuel. Dump it when below 50ish.

tried that and flooded it. fouled a plug for about 30 seconds, not great for my new motor. Now I'm going to increment it 3-5% at a time and see where it gets me.

Toni
04-08-2014, 01:19 PM
not a great sign, fluid coming out of my transfer case looks like silver paint. When I installed it I noticed shitty looking fluid in it and tried flushing it a bunch. It looks better now than it did. I'm going to change it a time or two again, but if it doesn't clear up it is going to have to go back to ray.

Weird thing is it looks like aluminum...

Interesting. I noticed the same thing with a few miles on mine as well when I was changing out clutches last year. I haven't checked the fluid since and I just figured it was from machining. I may check again. Would be curious on updates of this.

familyMAN
04-08-2014, 01:22 PM
Did I say more, I meant less;). If you have to touch the throttle to get it to start better, that usually means less fuel since you are adding more air by opening throttle plate.

Unfortunately I don't think my settings in AEM will be transferable but mine starts well when cold and maybe a hair longer than stock when warmer. Took some fiddling though.

Chris@Rvengeperformance
04-08-2014, 01:27 PM
Did I say more, I meant less;). If you have to touch the throttle to get it to start better, that usually means less fuel since you are adding more air by opening throttle plate.

Unfortunately I don't think my settings in AEM will be transferable but mine starts well when cold and maybe a hair longer than stock when warmer. Took some fiddling though.

interesting, general consensus is more fuel is needed. It will fire up, but needs prodding to get it running smooth at first.

I'm already running about 1/3 less cranking pulse than stock since when I went with big injectors last year, but it was always in the 70s+ so I never had a chance to tune this range. I'll see what it does next time. I tried about 20% more cranking fuel and it flooded. Then the next day or so I tried 90% of my initial values and it started worse, so I'm back to what I was last year and it started without flooding, and the wideband was reading pretty decent right away, but it did take 3 crank sets and some throttle prodding. Today I added 3% and will have to see if that helps.

It is more sensitive to changes than I anticipated.

Chris@Rvengeperformance
04-08-2014, 01:33 PM
The fuel being super old doesn't help I am sure.

Sent from my RM-845_nam_vzw_100 using Tapatalk

familyMAN
04-08-2014, 01:40 PM
Starting fuel should be separate from warm up enrichment. If it starts good but is then too rich until it warms up, there should be warm up enrichment table to play with. Unless I misunderstood, it sounds like you should keep the start up fuel high but need to back off your warm up enrichment.

mb3000
04-08-2014, 01:56 PM
^This. The initial crank pulse is what gets the engine going (basically) and the warm up enrichment is what gets it to operating temp. A good balance of the two will give you perfect starts in any weather.

Chris@Rvengeperformance
04-08-2014, 02:02 PM
I don't think I am describing it well. After it runs for like a second its fine. I'll take a video if I can't solve it.

Sent from my RM-845_nam_vzw_100 using Tapatalk

mb3000
04-08-2014, 02:36 PM
Sounds like your initial crank pulse is what needs modifying.

Greg E
04-08-2014, 02:45 PM
I'm confused with all the back and forth comments...

Chris, you need to back off on the "Post start enrichment Factor" or "Post start enrichment timer" if you're needing to hold the throttle open to get it idle after initial starting. This is a completely separate factor from warm up enrichment (which I usually disable or only set to low single digit numbers).

FamilyMAN of you want to post your AEM settings, I can translate them to work with Chrome. I do just the opposite all the time for AEM guys. The start up routines are nearly identical.

Chris@Rvengeperformance
04-08-2014, 02:54 PM
It will crank and just try to catch, but die, then if I try again and I gig the throttle it will pick up.

It cranks a lot longer before trying to catch if I run less cranking ipw.

After it runs smoothly for a moment it runs mid tens afr for about 10 seconds, then starts going up and within less than 30 seconds it is at stoic.

Sent from my RM-845_nam_vzw_100 using Tapatalk

Greg E
04-08-2014, 03:35 PM
Remember E85 only has about 70% of the energy that normal gas does so you might not need to have as much as you think pulled out.

Chris@Rvengeperformance
04-08-2014, 04:27 PM
I'm confused with all the back and forth comments...

Chris, you need to back off on the "Post start enrichment Factor" or "Post start enrichment timer" if you're needing to hold the throttle open to get it idle after initial starting. This is a completely separate factor from warm up enrichment (which I usually disable or only set to low single digit numbers).

FamilyMAN of you want to post your AEM settings, I can translate them to work with Chrome. I do just the opposite all the time for AEM guys. The start up routines are nearly identical.

The post start enrichment comp on the higher temps been reduced to almost nothing and that's working great. I have not reduced the post start enrichment on the lower temps nearly as much. That may be what it needs, I don't really want to change more than one thing at a time, especially since it is not starting *that* hard right now and I do not want to be hard on my new motor loading it up with fuel.


-25.6
-0.3999999999999986
17.6
44.60000000000001
68
93.20000000000002
122
170.6
179.6

2.203125
2
1.78125
1.3125
1.203125
1.125
1.046875
1
1

At the end of the day I find this startup tuning pretty difficult, I may shoot a video and send you my rom if I can't get a handle on it. Everything thing happens so quick and after the first crank the remaining data isn't really valid until the next day. What's likely to happen is the temps outside are going to keep warming up and I'll just have to deal with this next fall. The main thing is once it warms up just a bit it runs great and if I can get the DMV stuff squared away I can complete the breakin of this thing.

I appreciate all the advice though guys, it is just the difficulty of describing once happens in a few seconds while cranking and starting, and the numerous settings that can alter the behavior that it is hard to tune remotely or especially by committee. Logging isn't really helping me a whole lot as there is not a lot of published data about what I'm supposed to see in the first 2 seconds of the car coming to life and the wideband may get pegged in the first moment, making a read hard to get. I'm sure someone with a good feel for this could solve it better than I can just listening to the car.

Chris@Rvengeperformance
04-08-2014, 06:10 PM
woot, she is legal!

futurevr4man
04-08-2014, 08:46 PM
18 eh?! :icon23:

how does Jenn feel about that?!

Greg E
04-08-2014, 08:51 PM
The main thing is once it warms up just a bit it runs great and if I can get the DMV stuff squared away I can complete the breakin of this thing.

It's not that the motor needs to warm up to run good, it's that you are relying on closed loop to do the tuning for you and there a 10-30 sec delay depending on your coolant temp.

Shoot me some logs if you need to but you're on the right track.

Chris@Rvengeperformance
04-09-2014, 10:45 AM
Thanks, I think I am on the right track.

I added 2 ms to the cranking pulse and took away 5% on the post start enrichment factor. It caught faster, but died faster after that. So, I added 2 more ms to the starting IPW and put the post start enrichment factor back where it was. It caught a little faster and I was able to keep it running, but it was a little rich for a bit.

So, I removed .2 ms from the post start enrichment timer and we'll have to see what it does tomorrow. The biggest takeaway for me is you can still learn something if you alter things before it completely fires up, rather than waiting a day, and it is really sensitive to changes. 2 ms may be all it needs, but 6 might flood it.

Greg E
04-09-2014, 10:48 AM
It's supposed to be in the lower 10s just after start up and gradually get to 14.7 after closed loop starts and the coolant temps warm up.

If you're trying to get a leaner start that won't work.

Chris@Rvengeperformance
04-09-2014, 10:48 AM
It's supposed to be in the lower 10s just after start up and gradually get to 14.7 after closed loop starts and the coolant temps warm up.

If you're trying to get a leaner start that won't work.

good, then except for the moment after it catches it is running right.

Chris@Rvengeperformance
04-14-2014, 11:09 AM
I think these ar3933 plugs may be too cold for me. Starting in the 50s this morning was even a little hard and I had a miss until it warmed for a minute. It isn't starting rich as far as I can tell.

I may have to try an eight series ngk.

Going for fresh fuel today to see if that helps.

Sent from my RM-845_nam_vzw_100 using Tapatalk

green-lantern
04-14-2014, 11:22 AM
woot, she is legal!

Cool, I can't wait to drive mine again.

Chris@Rvengeperformance
04-14-2014, 12:20 PM
I'm talking to myself, but I think what I am seeing here is just stronger interpolation towards the 45 degree rows. In the 45 degree row I was still running 2500 MS of post start enrichment vs the 1400 in the 68 row, so I've dropped the 45 degree row to 2000. We'll see if that gets closer, it is going to be mild to cold all week. I also reduced the IPW 4 Ms in the 45 degree row.

Greg E
04-14-2014, 12:40 PM
Stupid question: did you lower the min IPW value? Think you did. Just can't remember.

Chris@Rvengeperformance
04-14-2014, 12:48 PM
Stupid question: did you lower the min IPW value? Think you did. Just can't remember.

hmm maybe not, it is set to 1.28 mS. Is this an issue?

Greg E
04-14-2014, 01:02 PM
Only if you're trying to run less than that value.

Chris@Rvengeperformance
04-14-2014, 01:05 PM
ok, I don't think so, my minimum cranking IPW is 2.4

Chris@Rvengeperformance
04-14-2014, 04:17 PM
I really think I am fighting these cold plugs a little. I took it out at lunch and ran it pretty hard. It was not super smooth at first, but after 2 pulls it smoothed out, so I think the plugs were getting dirty. My commute is about 10 minutes, so sometimes I don't get a chance to run it super hard and I think they are getting dirty and becoming hard to start when they cool off.

The good news is other than that it runs great. Turned over 100 miles today. Drove for a while and idle oil pressure is down to 26.5 instead of 27, oil does not seem thinned or smell like fuel, but it is time to change it anyway. Still makes 58-60 PSI at 2000 RPM. Really I need to setup a rig to log pressure vs rpm vs oil temp, but I'm not sure I'll get to that.

4th gear was fixed using a zip tie to get the cold piping out of the way. The leaks on the oil cooler seem fixed since I tightened them a bit more.

Jimvr4
04-14-2014, 05:00 PM
Are you using that netbook / PC to display gauges in Evoscan yet?

Chris@Rvengeperformance
04-14-2014, 05:13 PM
Are you using that netbook / PC to display gauges in Evoscan yet?

using the 8" windows tablet. Actually burned a tune with it this morning without an issue. The gauges are slightly hard to see in direct sunlight, but I'm going to set up the warning sounds for evoscan.

Jimvr4
04-14-2014, 05:20 PM
Which gauge setup are you running? I didn't figure out how to get them to display. Once I get it then I will output digital video and display on my DVD navigation unit ( using a dig video to analog video converter)

Chris@Rvengeperformance
04-14-2014, 05:23 PM
Which gauge setup are you running? I didn't figure out how to get them to display. Once I get it then I will output digital video and display on my DVD navigation unit ( using a dig video to analog video converter)

I don't know, one of the crappy "full gauge" ones. I tried making a custom setting, but it was really pissing me off and I gave up for now. I'd have an easier time writing a gauge display from scratch than trying to dick with this evoscan gauge designer.

Jimvr4
04-14-2014, 07:12 PM
My problem exactly !!!

Chris@Rvengeperformance
04-15-2014, 11:12 AM
fired up like stock today at 40 degrees outside temperature. Either the tune is closer or I was right about the plugs needing a pull a day to stay clean or both.

Greg E
04-15-2014, 12:01 PM
You have an ignition amp installed right?

Chris@Rvengeperformance
04-15-2014, 12:10 PM
You have an ignition amp installed right?

nope, sold it when we bought the house. It is on the list. Gotta pay off the riding mower we picked up last week first. Probably next month will pick up a dli.

I'm sure the stock ignition trying to fire these cold plugs isn't easy, but it pulls clean. They are gapped .025 from the factory and my tune is in the 12s WOT, at least in the 2nd gear pulls I've tried thus far.

Chris@Rvengeperformance
04-15-2014, 09:39 PM
looks like the local station is selling e70 still. I had a little less than a quarter tank of fuel from last year. I tested it before I left and it was 85-87% alcohol. I saw a sign on the gas station that said minimum 51%! alcohol, so with that in mind I only put in 6 gallons. I tested the fuel again and it right dead set between e70 and e85, about 77%. Assuming I had about 6 gallons in the tank before I'd said the source was e70. I may pickup a can of it straight to check again.

I had noticed the car running about half a point richer, so I assumed it was e70. It actually works out okay because that brought my afr from low 12s in to about the mid to high 11s, which works out pretty good. Kinda accidental flex fuel. Seems like even down to e50 it should be just getting in to the 10s afr. Boost is only about 13-15 PSI right now anyway.

Chris@Rvengeperformance
04-15-2014, 10:46 PM
130 miles on it, so it needed an oil change. I cut open the filter and found nothing, no flakes, no sparkles. Oil is a little darker than new of course, but there is no material in it.

Just a little bit of iron dust from the rings on the magnetic drain plug.

I don't know about this IPS pan claiming to hold a lot more than stock, it sure doesn't seem to. I used to buy 5 quarts, put as much as possible in the filter and then the rest in the motor. Now I fill the filter and put a fresh 5 more quarts in the pan and it is full. Doesn't seem like it holds much more at all. Maybe half a quart. I've checked it many times to be sure. I've also checked it immediately after shut down in case the oil cooler is draining back in the pan, no difference that I can see.

CoopKill
04-15-2014, 11:34 PM
Nice on the findings, interesting about the pan.

green-lantern
04-16-2014, 12:57 PM
130 miles on it, so it needed an oil change. I cut open the filter and found nothing, no flakes, no sparkles. Oil is a little darker than new of course, but there is no material in it.

Just a little bit of iron dust from the rings on the magnetic drain plug.

I don't know about this IPS pan claiming to hold a lot more than stock, it sure doesn't seem to. I used to buy 5 quarts, put as much as possible in the filter and then the rest in the motor. Now I fill the filter and put a fresh 5 more quarts in the pan and it is full. Doesn't seem like it holds much more at all. Maybe half a quart. I've checked it many times to be sure. I've also checked it immediately after shut down in case the oil cooler is draining back in the pan, no difference that I can see.

Does the stick show full or is it right between the marks? If the pan was wider it would take it more than normal to top it off. Like normal is a half quart low if you are between the marks but if the pan were a lot wider it might take a quart to a quart and a half to top it off. Even if true that doesn't seem much bigger though.

Chris@Rvengeperformance
04-16-2014, 01:01 PM
Does the stick show full or is it right between the marks? If the pan was wider it would take it more than normal to top it off. Like normal is a half quart low if you are between the marks but if the pan were a lot wider it might take a quart to a quart and a half to top it off. Even if true that doesn't seem much bigger though.

It is on the top notch.

green-lantern
04-16-2014, 04:56 PM
It is on the top notch.

Maybe your dipstick is too short


:p


Edit: that doesn't make sense. it would have to be too long. :lo5l:

Chris@Rvengeperformance
04-16-2014, 06:07 PM
never had any complaints!

anyonebutme
04-16-2014, 08:13 PM
half quart sounds about right, honestly. The IPS kickout is smaller than SCE's and the SCE pan only added a little under a quart IIRC. Someone who has one might be able to chime in. Just looking at the pans there isn't much added volume from stock. The trick is getting that extra oil to be at the pickup when you need it.

Chris@Rvengeperformance
04-25-2014, 11:05 AM
Well 210 miles or so and no particular engine problems to report. Having some misfire issues at WOT though. I think I have fouled out the ar3933 plugs. I can't even make a clean pull in first at 14-15 PSI. It misfires around 4200 and then again 5500, sounds like it is running on 5 at that moment. 80% throttle or so is clean.

AFR in mid to high 11s. No ignition amplifier, but stock stuff should be able to handle this low boost.

I think I am going to have to try the ngk R5671A-8 for now at least until I get this sorted or start running more boost.

wingnut
04-25-2014, 01:29 PM
Subscribed for the awesome...

...was planning similar white second gen/ray block/750 turbos/e85 until life temporarily got in my way, so forgive me if i live vicariously within this thread :p

kywhitelightning
04-25-2014, 01:56 PM
Well 210 miles or so and no particular engine problems to report. Having some misfire issues at WOT though. I think I have fouled out the ar3933 plugs. I can't even make a clean pull in first at 14-15 PSI. It misfires around 4200 and then again 5500, sounds like it is running on 5 at that moment. 80% throttle or so is clean.

AFR in mid to high 11s. No ignition amplifier, but stock stuff should be able to handle this low boost.

I think I am going to have to try the ngk R5671A-8 for now at least until I get this sorted or start running more boost.

Get that AFR up some. Alcohol does not like the 11's at all.

Jeff

Chris@Rvengeperformance
04-25-2014, 04:41 PM
Get that AFR up some. Alcohol does not like the 11's at all.

Jeff

yeah I hear that and have been leaning it out some. These are not 3rd gear pulls, so I do not want to go crazy with the fuel map at the moment. I do not see the sense of beating on the car in 3rd if it gets pissed in 1st already.

I changed the front 3 plugs at lunch to the 8 series ngk and also leaned out the problem area around 4500 to 11.8, just touching 12.0. It pulled hard up to about 5500 and stuttered pretty hard (it is about 11.6-11.8 there), so I'm going to change the rear three plugs this weekend and see how it runs. If that does not fix it I can lean it a hair more, but I suspect something is wrong with the ignition components.

I also don't want to lean it out all the way to 12.0, because when the station changes to e85 it is going to be pretty lean. I don't really want to get over 12.5:1.

TurboSinceBirth
04-25-2014, 09:30 PM
It sounds more like an ignition issue. I wouldn't get ignition problems running 11s but 10s definitely did it. I ran mine at 12:1 for the cleanest results. I've been leaner but didn't want to on stock thinner 2nd gen ringlands. I'd definitely change the rear plugs. What gap are you running? How old are the PTU, coils, and wires?

Chris@Rvengeperformance
04-25-2014, 09:53 PM
It sounds more like an ignition issue. I wouldn't get ignition problems running 11s but 10s definitely did it. I ran mine at 12:1 for the cleanest results. I've been leaner but didn't want to on stock thinner 2nd gen ringlands. I'd definitely change the rear plugs. What gap are you running? How old are the PTU, coils, and wires?




kinda my thoughts at the moment. 12:1 will light easier, but it should fire off even 11.0:1 at this low boost afaik.

The autolites are factory gapped at .025, I've gapped the ngks to .022.

The wires are msd with maybe 5k on them. Ptu and coils got supposedly new from a guy and now have about 10-15k on them.


If the rear plugs don't fix it I'll replace the coils and ptu to be safe, although that is a good chunk of change and the coils bench test ok. I forgot to bench test the ptu, but I thought they either worked or didn't. I don't want to throw a dli at this yet because something is clearly wrong.



Sent from my RM-845_nam_vzw_100 using Tapatalk

TurboSinceBirth
04-25-2014, 10:10 PM
kinda my thoughts at the moment. 12:1 will light easier, but it should fire off even 11.0:1 at this low boost afaik.

The autolites are factory gapped at .025, I've gapped the ngks to .022.

The wires are msd with maybe 5k on them. Ptu and coils got supposedly new from a guy and now have about 10-15k on them.


If the rear plugs don't fix it I'll replace the coils and ptu to be safe, although that is a good chunk of change and the coils bench test ok. I forgot to bench test the ptu, but I thought they either worked or didn't. I don't want to throw a dli at this yet because something is clearly wrong.



Sent from my RM-845_nam_vzw_100 using Tapatalk

Yeah there's definitely something going on. Your plug gap is fine. I ran .028 to 24 psi on a stock new ignition with e85 before putting the DLI on so .025 and .022 should work.

Greg E
04-25-2014, 11:33 PM
Want to know a secrete? Being up the dwell % limit table in the Timing section. It should be set to 75% across the board.

Set them to 100% and flash. You will get just a bit more spark from your coils. Should help you a little if this is a blow/foul out issue.

Chris@Rvengeperformance
04-25-2014, 11:58 PM
Thanks Greg, was hoping you'd post specifics on that.

Sent from my RM-845_nam_vzw_100 using Tapatalk

kywhitelightning
04-26-2014, 04:34 AM
What are your coolant temps?

I ran .025" up to 28psi with slight blowout. I regapped to .022" and no blowout since. That seemed to come with a price though as I found it will try to foul the plugs with normal driving. Once i put my foot in it it's good for some driving. This could also have a little to do with the cooler than stock coolant temps I keep it at but, I think it's mostly related to the small gap.

Jeff.

Chris@Rvengeperformance
04-26-2014, 10:32 AM
What are your coolant temps?

I ran .025" up to 28psi with slight blowout. I regapped to .022" and no blowout since. That seemed to come with a price though as I found it will try to foul the plugs with normal driving. Once i put my foot in it it's good for some driving. This could also have a little to do with the cooler than stock coolant temps I keep it at but, I think it's mostly related to the small gap.

Jeff.




about 185





Sent from my RM-845_nam_vzw_100 using Tapatalk

Greg E
04-26-2014, 10:48 AM
Thanks Greg, was hoping you'd post specifics on that.

Sent from my RM-845_nam_vzw_100 using Tapatalk

It's been in the V2 Tech Thread since the beginning. ;)

Chris@Rvengeperformance
04-26-2014, 03:08 PM
It's been in the V2 Tech Thread since the beginning. ;)

I saw the dwell stuff, but I guess I missed where you said change it to 100%

I swapped the rear three plugs with ngk 8 series non projected gapped to .022 and it pulls clean as a whistle now. Idles better too. Have not changed the dwell yet, wanted to do one thing at a time.

closed loop is working great lately, dithers between 14.3 and 14.6, doesn't move much.

Chris@Rvengeperformance
05-02-2014, 09:41 PM
http://www.chrisbehnken.com/Images/photos/WP_20140502_003FD.jpg?635346588209691343

CoopKill
05-02-2014, 10:14 PM
https://1es57a.dm1.livefilestore.com/y2mHeAnnZE4RBPVjc8lw1oi_YkmnGls6NmLaMGqC7e-zTEDksxU43skvL36RqzxFJ31hJhdTOATw24tDPSyY5NCx-QiTg_VJnbykCx9PGQEuPw3nHJvjV_FY0vbXaD3gP_T/WP_20140502_003.jpg?psid=1

Are you on stechs?

Chris@Rvengeperformance
05-02-2014, 10:17 PM
http://www.chrisbehnken.com/Images/photos/WP_20140502_003FD.jpg?635346588209691343

Are you on stechs?

Yes..

green-lantern
05-02-2014, 10:36 PM
http://www.chrisbehnken.com/Images/photos/WP_20140502_003FD.jpg?635346588209691343

I think Chris might have rebuilt his car twice in the time it's took me to take my trans apart. WTF I got to get motivated!

NOMIEZVR4
05-03-2014, 02:05 AM
Can you post your timing map?

Car looks great BTW...

Chris@Rvengeperformance
05-03-2014, 01:59 PM
Can you post your timing map?

Car looks great BTW...




I'd rather not post the entire map, it isn't really relevant for a 3.0 anyway, strokers need less timing.

It is very conservative though, high single digits peak torque and 17 or so near 7000.




Sent from my RM-845_nam_vzw_100 using Tapatalk

futurevr4man
05-03-2014, 05:07 PM
You're gonna shoot yur eye out kid

HLxDrummer
05-03-2014, 10:11 PM
Your car looks fantastic!

Hellaflush
05-04-2014, 12:10 AM
http://www.chrisbehnken.com/Images/photos/WP_20140502_003FD.jpg?635346588209691343


This place looks somewhat familiar...

Sent from my SAMSUNG-SGH-I717 using Tapatalk 2