PDA

View Full Version : New carpet and sound deadening project



n2nsanity
02-19-2014, 04:24 PM
I didn't plan on this, but I've yet again started another project without completing the 15 others I was already working on. I started this because it's a convenient time since the seats are already out being re-skinned.

I started out installing the seat skins I bought last year, but then couldn't help but to clean up the nasty old rusty frames why they were out. With the seats out, I realized how nasty the carpet was, so I ordered new carpet. With the carpet out, I thought this would be a good time to do some sound deadening. I always hated how noisy the car is inside. Things like talking on the cell phone or listening to music would be so much better if I could get rid of some of the road noise in the cabin. I keep digging myself deeper and deeper, but this is where I'm at now. Hopefully I find a few tricks that will be useful to someone else.

So, seats and carpet out.
6464

The foot area for driver and passenger side have a hollow chamber. I think this is where half of the noise comes from. I decided to try some "Great Stuff" expanding foam in these chambers.
There are a bunch of holes in the top covered with this black tar-like material. Some of them were broken already, but I tapped a few others. I think a hole in each of the 4 corners and one in the middle would be enough to fill it up.
6465
After doing this, there was a night and day difference of the echo when you tap on the floor. I think this one trick (which is also the cheapest and easiest) will be more effective than anything else I do, lol.

There are also 2 other small chambers where the seat rails mount to the floor. Filled these up fairly easily and I could immediately tell a difference in the sound here as well.
6466

I used some Stinger Roadkill mat instead of Dynamat, but I think the results will be similar. I also read that partial coverage (about 25%) is usually all you need. I went with more like 50% to be on the safe side and cover the larger areas. By this time, most of the foam was dry so I shaved off the excess with a razor. I also ground down and primered/painted a few mild rusty spots while I was here.
6467

So from what I've done so far, the Stinger mat seems to reduce vibration by about 25%, but the expanding foam seems more like 75%.
I used up 1 can on just the driver side. 2 or 3 cans should be plenty.

*Mental note to make a video later comparing sound of untreated passenger side vs this foam filled driver side.

sergechronos
02-20-2014, 06:04 PM
The foam is a great trick that has helped me with other chassis before. I've always felt that the doors at a big issue for our cars because they're so big and empty. I recall a thread about it a while back where the guy said like 25-50% coverage with the dynamat and then topping with something else totally eliminated road noise there. Think it was like a closed cell foam or vinyl mat of some kind

Sent from my XT1080 using Tapatalk

CoopKill
02-20-2014, 10:08 PM
I ended up doing 100% coverage with edead but for the doors. I have plans for them, but it seems most of the noise in mine still comes from the rear wheel well area. I may try the foam trick in that area to see.

DrGonzo
02-20-2014, 11:29 PM
The doors need deadener on both the inside skin above and below the bar and a couple small pieces on the outer frame. Also adding some foam sheet to keep the noise out. Doors are solid now and you can hear it when you close them how solid they are. Here is my stereo thread that shows how I handled the noise issue. This is very effective and cheap.

http://www.3sgto.org/audio-video-systems/13579-time-revamp-stereo-stealth.html

n2nsanity
02-21-2014, 04:14 AM
Finished up the driver side...

Used one big piece here to cover that big hollow chamber.
6468

I was going to buy some carpet padding but thought I'd give this stuff a try. This was a garage mat, lol.
6469

n2nsanity
02-21-2014, 04:19 AM
New carpet

The lighting was off on this one. The carpet is a dark black.
6470

Side view showing thickness
6471

Bottom side
6472

As you can see, the new carpet requires a good bit of trimming. It is somewhat molded to fit the floor, but not near as precise as the oem carpet. But, with the extra padding I'm adding, I think it should fit fine.



Old carpet

Bottom side
6473

Side view
6474

n2nsanity
02-21-2014, 04:40 AM
Foaming up the passenger side. This stuff really expands, lol.
6475

Put some mat on the harness cover
6476

One big piece on the passenger side floorboard
6477

And passenger side is done and I'm pretty much ready for carpet
6478

n2nsanity
02-21-2014, 04:45 AM
New carpet finally going in :)

6479

6480
*Later on I realized I cut too low on the passenger side of the console.

I feel much better now that it's somewhat in the car. Past my bedtime... Hopefully I can finish this up tomorrow.

n2nsanity
02-21-2014, 11:14 PM
Time for some semi-related distractions. Did this inside while it was storming outside.

Refurbishing the nasty old charcoal center console carpet pieces with black. Should match the carpet pretty well.
6481

These are glued on the front and stapled on the back.
6482

Old carpet off
6483

I used some loctite spray adhesive for the front and a hot glue gun instead of staples for the back side.
6484

I think they turned out really good
6485

n2nsanity
02-21-2014, 11:25 PM
Driver side console trim in
6486

Almost forgot to cut a hole for the power seat wire harness
6487

Driver seat in
6488

Better shot. Still need to reattach lower dash panel
6489

Passenger seat is in. It needs some tweaking, but I have to say, I really like it.
6490


I sorta rushed through towards the end. I need a different stapler if I want to use the plastic clips for securing the carpet to the threshold. For now I just tucked it under the door sills.

One useful trick I found out for cutting holes for bolts. Put bolts in the holes before installing the carpet. Makes it easier to find them and when you cut the holes, you won't end up with carpet or padding stuck in the threads.

bearded1
02-22-2014, 02:36 AM
Where'd you get your carpet from?

Good tip on the foam for the floorboards. I've never had the carpet up from mine, didn't realize that was there, but I've used foam before and the results are usually impressive from the little bit of time and money.

Also your doors could definitely use some love with CLD tiles. You can also use foam behind the crash bar, but in the past I've used an extruded rubber stuck between the outer skin and the crash bar. It mates the two surfaces together and gets rid of a good amount of resonance. I've done it on my VR4 and several other vehicles with great results, and even better with a few CLD's above and below. All these things are really just helping control resonance, but that is a definite issue with our cars, and it gets rid of the "tin can" effect" for sure.

Also FWIW, I usually buy stuff from http://sounddeadenershowdown.com/
Don is a very knowledgeable guy and can answer just about any question you can throw at him, and can even help with a plan of attack if you need that.

Anyway, nice job!

Jake

n2nsanity
02-22-2014, 10:07 PM
I've seen the sounddeadener showdown before. Some decent info on there where I got some ideas from. The sound deadening was a spur of the moment thing. "Well, carpet is out, maybe I should go ahead and do this too". Didn't have time to order anything, so I used what I had and could buy local.

Here's where I got my carpet from.
1990 1999 Mitsubishi 3000gt Carpet Kit Coupe | eBay (http://www.ebay.com/itm/1990-1999-Mitsubishi-3000GT-Carpet-Kit-Coupe-/281121238287)

It looks a little more formed in the picture. But if you compare an oem carpet to this, there's a night and day difference. I know you can contour it a little more with a steamer, which I didn't do yet. Also, the corners want to bunch up a little. For the most part it fits pretty well. But have to be very cautious on the trimming. It looks like you have to trim a lot, but you don't.

But anyway, once installed, it looks really nice. Soooo much cleaner than the 20 year old crap I had in there.

CoopKill
02-22-2014, 11:02 PM
Yeah I think is the same as I got, and +1 on trimming. The heal pad is back a bit too far on mine as well.