View Full Version : '91 with recent plug and play clone (Jesters)
dalgroth
11-14-2013, 01:26 AM
I was hoping for some help with my current issue as I dropped in a clone ecu and scanned the boards for an array of information, most of it in regards to tuning. Right now I've got a pretty stock setup so I didn't buy the Tactrix 2.0 cable, trying to get my 91 vr4 with 88k miles to run smooth since May has been a hassle. In May the old ECU went out (capacitors), prior to it going out everything ran smoothly and no CEL was on. I replaced the ECU and since then what appears to have been a domino effect has occurred. The timing belt tensioner went out, or so I presume, as timing was off after the ECU was replaced so I did a 60,000 tune-up since I was down there anyways (It appeared a 60k had been done once, as the belt seemed new, the water pump was missing 1/2 the stock screws and had replacement ones on it). Once finished, the car ran well for about two days before the tachometer went out; I took it in for diagnostics and was informed that the tach had gone bad- not the new (remanufactured) ECU. Within a week the car started driving poorly, hesitating at acceleration, etc... but the CEL was on. I used an ohm-meter and pulled the codes; it read that cylinders 1-4 weren't firing and fuel injectors were bad. I replaced the injectors and ignition coil and the car ran well for 50 miles, then regressed to prior read-out: cyl 1-4 misfiring. The ECU became suspect, so I took it in. I was told that the ECU was skipping cyl 1-4 by itself. I decided to purchase a Jesters clone ECU PnP for the 91. Once installing it I got a few random weird codes and one consistent one; P0335, crankshaft position sensor bad. This made sense because the tach didn't read right, the misfiring on specific cylinders and long cranks before start. So, I replaced it and the car ran well without a CEL for one day. Now, on two separate resets I've had the following CEL codes (below), a couple of which I've seen more than once- even before the last resets.
CODE Meaning
P0156 02 Sensor Circuit Malfunction (Bank 2 Sensor 2)
P0155 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
P0161 Oxygen O2 Sensor Circuit Low Voltage (Bank 2, Sensor 2)
P0136 Oxygen O2 Sensor Circuit Low Voltage (Bank 1, Sensor 2)
P0135 Oxygen O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)
P0141 O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2)
P1400 MAP Sensor Test
P0446 Evaporative Emission Control System Vent Control Circuit Malfunction
Now, my question is, am I having really horrible luck, or, due to the set of sensors reading wrong, is it possible I really just need to buy the Tactrix 2.0 and tune the car? Any advice would be greatly appreciated. The only symptoms I now seem to be suffering is a CEL and long cranking to get the car to start (5+ seconds).
CoopKill
11-14-2013, 01:43 AM
You need tactrix, and evoscan/ecuflash to set up the ecu to work with your car. There are several setting needing done for it to work with your year.
Greg E
11-14-2013, 12:23 PM
You need tactrix, and evoscan/ecuflash to set up the ecu to work with your car. There are several setting needing done for it to work with your year.
This man knows his stuff. :)
Sounds like you got the mechanical issues all worked out but now you just need to configure the peripherals for your car. Take a gander at the threads stickies on top of this sub forum.
dalgroth
11-14-2013, 11:22 PM
That's actually what I was thinking, however 3sx.org and Adam were saying the ECU comes PnP for a 91, but the misc errors that only showed up after switching to it seemed odd. I forgot to mention that the tour/sport light for suspension flashes now as well and the windshield washer reservoir light is on despite being full. Thank you guys for confirming what the research seemed to point me in the direction of.
surfersamu
11-15-2013, 01:05 AM
Read the manual! I have read it like 30 times, i continue to read it.. and everytime i read it again i learn or understand something new...
thiss is from the tuning guide by monochrome:
So when you first install your Flash ECU, you'll need to disable bits 15, 14, 13, 11, 10, 9, 3 and 1 to ensure no CELs if you're a 1G car (or any car with a full vac reduction) without any of these systems. Even the 96/97 cars will need to disable bits 13-15 as you guys don't have the same purge system as the 98/99 cars.
http://www.3sgto.org/tuning-engine-electronics-ecu-discussions/10775-how-tune-your-3-s-using-chrome-flash-ecu.html
-------------
You are messing with ur car's brain u wanna make sure u know why you have to turn off these periphery bits.
Sent from my iPhone using Tapatalk (http://tapatalk.com/m?id=1)
99 vr4
11-17-2013, 03:09 AM
I normally set the bits for 1G customers for the sensors that they do not have, like the MAP sensor, secondary O2, and ECU controlled O2 heaters. Most of the P codes you listed were because the peripheries were not set for the 1G car . . . this is only legal if the ECU is destined for a 1G car.
This is not a base tune and I normally due this in order to facilitate the ECU installation for customers who are only replacing a failed OEM ECU.
That being said the ECU has nothing to do with the tour sport light flashing. The ECS and ECU share the same MUT bus, but normally do not communicate between each other, that we are aware of.
On a side note, it was discovered that the AT Controller communicates with the ECU via not only several hard lines, but over the MUT bus using the OBDII K Line.
Gray Haze
11-19-2013, 11:34 AM
That's actually what I was thinking, however 3sx.org and Adam were saying the ECU comes PnP for a 91, but the misc errors that only showed up after switching to it seemed odd. I forgot to mention that the tour/sport light for suspension flashes now as well and the windshield washer reservoir light is on despite being full. Thank you guys for confirming what the research seemed to point me in the direction of.
The only light that a flash ecu can set is the CEL due to you not setting up the peripheries correctly. All other lights are un-related, coolant overflow bottle never crosses path with the ecu, and ECS Controller only gets a TPS Signal from the ecu and speed signal from the speed sensor.
You need a tactrix cable and you need to read the stickies on how to adjust the ecu for your specific car.
Jesters Deadd
11-19-2013, 12:15 PM
I was hoping for some help with my current issue as I dropped in a clone ecu and scanned the boards for an array of information, most of it in regards to tuning. Right now I've got a pretty stock setup so I didn't buy the Tactrix 2.0 cable, trying to get my 91 vr4 with 88k miles to run smooth since May has been a hassle. In May the old ECU went out (capacitors), prior to it going out everything ran smoothly and no CEL was on. I replaced the ECU and since then what appears to have been a domino effect has occurred. The timing belt tensioner went out, or so I presume, as timing was off after the ECU was replaced so I did a 60,000 tune-up since I was down there anyways (It appeared a 60k had been done once, as the belt seemed new, the water pump was missing 1/2 the stock screws and had replacement ones on it). Once finished, the car ran well for about two days before the tachometer went out; I took it in for diagnostics and was informed that the tach had gone bad- not the new (remanufactured) ECU. Within a week the car started driving poorly, hesitating at acceleration, etc... but the CEL was on. I used an ohm-meter and pulled the codes; it read that cylinders 1-4 weren't firing and fuel injectors were bad. I replaced the injectors and ignition coil and the car ran well for 50 miles, then regressed to prior read-out: cyl 1-4 misfiring. The ECU became suspect, so I took it in. I was told that the ECU was skipping cyl 1-4 by itself. I decided to purchase a Jesters clone ECU PnP for the 91. Once installing it I got a few random weird codes and one consistent one; P0335, crankshaft position sensor bad. This made sense because the tach didn't read right, the misfiring on specific cylinders and long cranks before start. So, I replaced it and the car ran well without a CEL for one day. Now, on two separate resets I've had the following CEL codes (below), a couple of which I've seen more than once- even before the last resets.
CODE Meaning
P0156 02 Sensor Circuit Malfunction (Bank 2 Sensor 2)
P0155 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
P0161 Oxygen O2 Sensor Circuit Low Voltage (Bank 2, Sensor 2)
P0136 Oxygen O2 Sensor Circuit Low Voltage (Bank 1, Sensor 2)
P0135 Oxygen O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)
P0141 O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2)
P1400 MAP Sensor Test
P0446 Evaporative Emission Control System Vent Control Circuit Malfunction
Now, my question is, am I having really horrible luck, or, due to the set of sensors reading wrong, is it possible I really just need to buy the Tactrix 2.0 and tune the car? Any advice would be greatly appreciated. The only symptoms I now seem to be suffering is a CEL and long cranking to get the car to start (5+ seconds).
Wow, that sounds like a lot of issues are showing their head at once. I wouldn't call it a domino effect since many of these issues are not related.
But it's bad luck with your car.
As Gray said, the nice thing is your fix for all the last bunch of CELs is a tactrix 2.0 cable and the related software.
dalgroth
11-27-2013, 08:50 PM
Over the weekend I got the tactrix cable in and Adam was quick to get me the chrome ROM so I was able to get all the appropriate peripherals disabled. The CEL is definitely gone and car is running smoother. I am however interested in getting the evap system working again and from everything I've read it seems to be possible to switch out the purge solenoid and re-enable 13-15. Unfortunately though I'm not finding the part number for the purge solenoid in anything I've read. The closest I came was a guy stating he had installed a 96 SL's into his 92. Does anyone perhaps have the part number for the purge solenoid I would need to swap to?
Greg E
11-27-2013, 09:22 PM
Over the weekend I got the tactrix cable in and Adam was quick to get me the chrome ROM so I was able to get all the appropriate peripherals disabled. The CEL is definitely gone and car is running smoother. I am however interested in getting the evap system working again and from everything I've read it seems to be possible to switch out the purge solenoid and re-enable 13-15. Unfortunately though I'm not finding the part number for the purge solenoid in anything I've read. The closest I came was a guy stating he had installed a 96 SL's into his 92. Does anyone perhaps have the part number for the purge solenoid I would need to swap to?
Well, the evap output still works regardless if you have those bits on or not. They are just the monitoring system for the evap (which you don't have the sensors for). All you have to do is hook up the solenoid and it'll function like a stock 98/99 evap system.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.