PDA

View Full Version : Question Regarding Fuel Trims



BlackSpyderVR4
11-03-2013, 09:38 PM
Ok, been reading all day. Trying to tune the low and mid fuel trims. So I do my first log and have a 12.5% on both front and rear mids trims. I have changed the MAF smoothness now by a total of +12% and it is still at 12.5%. The lowest I have seen is a 12.3%. The Lows are -10% rear and 2% front. I will be doing a vac check next weekend and Im going to check and see if I can find out what type of fuel injectors are on this bad boy. I was told they were stock, but I wasn't told about the car had a 1Piece CFDS and headers already installed. Any other ideas will be greatly appreciated for my trouble shooting purposes. Appreciate any help or advice.
-Mike

99 vr4
11-04-2013, 11:08 AM
Mike,

What year is the car?
Does the car have the stock fuel system or does it have aftermarket parts?
Does your car have an aftermarket fuel pressure regulator?
How many miles are on the O2 sensors?

Low Fuel Trims are the idle trims FYI.

A bad or lazy O2 can cause many problems with fuel trims.
Having an poorly adjusted FPR can cause problems.
It is not uncommon to have large changes in the VE table if you have intake changes, such as intercooler, piping, MAF, or exhaust changes, such as headers.

It is not uncommon to have some variance between front and rear, although -10 and +2 is a bit off . . .

BlackSpyderVR4
11-04-2013, 02:47 PM
96 VR4 Spyder. 78K. The car has aftermarket FPR, Filter, fuel rail loop, and I'm almost positive it has stock injectors. I have full exhaust, dual core intake and rebuilt TB by april, VAC reduction. I bought the car before deployment and only been back for a month and half so I'm still learning about the car and unscrewing everything the prior owner had done. Thanks for the help.

Greg E
11-04-2013, 03:35 PM
Sounds like you should get the car running good on the stock ECU before trying the flash ECU.

BlackSpyderVR4
11-04-2013, 05:02 PM
With the EVO MAF wired in that is not really an option. But prior to switching the car to the flash ecu it was running solid. But I may resort to this if after trouble shooting I may need to cut in and rewire the Stock MAF.

striker2
11-04-2013, 06:11 PM
If you need to put the stock MAF back in I have a connector that fits the EVO MAF. It will allow you to make an adapter harness using the stock 3S connector so you dont have to cut the EVO connector back off.

Greg E
11-04-2013, 06:22 PM
With the EVO MAF wired in that is not really an option. But prior to switching the car to the flash ecu it was running solid. But I may resort to this if after trouble shooting I may need to cut in and rewire the Stock MAF.

A bad MAF would cause the issues you're experiencing.

BlackSpyderVR4
11-04-2013, 11:16 PM
Well I went to Autozone to get the CEL checked. I was throwing 16 codes. I will have to go recheck the tune. I was throwing every code you would get from the VAC reduction (Wastegate, EGR, ETC) and then there were some O2 Heater and the trim codes were being thrown. I could have sworn I set up the ECU properly so It wouldn't throw the codes. The guy was useless and basically I asked to see the CEL Reader and read the codes myself. I will be going back tomorrow see if I get someone who knows what there doing or get that EVOSCAN 2.6 working so I can read my own codes. Also I used my compression check and I tried to pump it up with a tire pump and it just wouldn't build pressure. So I will be taking it to the DIY shop and use there air hoses to fill it up with air and find the leaks. I appreciate the help Gents and will keep you guys updates. If any more a Ideas come to your head please let me know.

Jimvr4
11-05-2013, 03:54 PM
..... get that EVOSCAN 2.6 working so I can read my own codes.....

If it's a stock 96 ECU it's not going to happen. Evoscan 2.6 won't connect reliably with the stock 96 ECU. I've personally verified v2.5 and v2.7 work with teh 96, not sure about v2.9

BlackSpyderVR4
11-05-2013, 08:26 PM
So I found a possible contributing factor. My rear turbo hot pipe going to intercooler wasn't even bolted down. I don't know how the car was Boosting so easy.

99 vr4
11-06-2013, 09:07 AM
You did not mention, what codes did you have?

BlackSpyderVR4
11-06-2013, 08:45 PM
Here are the codes: Throwing both codes twice for some reason. P0141 -Heated Oxygen Sensor Heater circuit Bank 1 Sensor 2 and P0156 Heated Oxygen Sensor circuit Bank 2 Sensor 2. So from what I understand both those sensors are just for the Cats. So it shouldn't be affected my fuel trims, correct?

Update: So I went drive around for 30minutes and Idled for 30min. Car dropped the codes and there is no more CEL light. The Trims are a lil better. So my rear and front mid trim are always identical and they settled at -4.10. Which should occur since I increased the MAF Smoothness by 12% and fixed the rear turbo hot pipe and now its running Rich. The Front/Rear Low while better is still way out of sync of each other (Front- (1.9%) Rear-(-11.7)). I'm going to have to go to the shop tomorrow or Friday and just check for vac leaks. Then start from stock rom and take this slow, Im getting to far ahead of myself.

My main questions right now:
1) Why would my front/rear low be so far away from each other?
2) Why are front/rear mid always the same?

Gents thanks for all the help, I do appreciate it.

mjannusch
11-07-2013, 04:13 PM
What car is this on? A Spyder?

If so, all Spyders are CA emissions, with the primary O2 sensors reversed on the stock harness compared to a Federal emissions car. That may be the issue why the front/rear low trims are so far out of whack. Check your conversion harness and trace the O2 wiring and see which stock wires go to what pins on the Chrome ECU. Or if you have one of the ECUs that doesn't need a conversion harness, check to make sure the O2 sensor jumpers are set for a CA emissions car.

99 vr4
11-07-2013, 10:28 PM
Here are the codes: Throwing both codes twice for some reason. P0141 -Heated Oxygen Sensor Heater circuit Bank 1 Sensor 2 and P0156 Heated Oxygen Sensor circuit Bank 2 Sensor 2. So from what I understand both those sensors are just for the Cats. So it shouldn't be affected my fuel trims, correct?

Update: So I went drive around for 30minutes and Idled for 30min. Car dropped the codes and there is no more CEL light. The Trims are a lil better. So my rear and front mid trim are always identical and they settled at -4.10. Which should occur since I increased the MAF Smoothness by 12% and fixed the rear turbo hot pipe and now its running Rich. The Front/Rear Low while better is still way out of sync of each other (Front- (1.9%) Rear-(-11.7)). I'm going to have to go to the shop tomorrow or Friday and just check for vac leaks. Then start from stock rom and take this slow, Im getting to far ahead of myself.

My main questions right now:
1) Why would my front/rear low be so far away from each other?
2) Why are front/rear mid always the same?

Gents thanks for all the help, I do appreciate it.

Yes the rear O2 would not effect the fuel trims. You need to turn off the periphery bits for the secondary O2 sensors . . . look in the Periphery 2 section.

Ok, the LOW trim is really the idle trim. You will need to add more VE (MAF Smoothness) at the lower air volumes up through 100 hz. It is ok to have up to +25%.

You also should have changed the MAF Size, Adder, and Scaling size for the ECO MAF.

After you flash the changes, reset the fuel trims by pulling the storage connector (or battery ground) for a few seconds. After 10 minutes of idle, you will see the new LOW fuel trims which should be closer to normal. The front may be + and the rear may be -. This is OK, as long as they are close in value. Mine sit at +2 front and - 2 rear.

Greg, correct me if I am wrong here.


What car is this on? A Spyder?

If so, all Spyders are CA emissions, with the primary O2 sensors reversed on the stock harness compared to a Federal emissions car. That may be the issue why the front/rear low trims are so far out of whack. Check your conversion harness and trace the O2 wiring and see which stock wires go to what pins on the Chrome ECU. Or if you have one of the ECUs that doesn't need a conversion harness, check to make sure the O2 sensor jumpers are set for a CA emissions car.

You should have been shipped a CA harness. But if you want to check any way, pin 75 of the stock harness should go to pin 71 of the new ECU. Pin 76 should go to pin 72. All pin numbers are as viewed from the wire side of the connector.

6126

On the 98/99 ECU, it is the 30 pin connector, the one all the way on the right as viewed from the wire side. Pin 71 is the first pin on the left, top row, as viewed from the wire side.

BlackSpyderVR4
11-09-2013, 11:55 AM
It appears the pins are good. I did adjust the MAF Size, Adder, and Scaling correctly for the EVO MAF. Have all the Peripheries set up properly for VAC Delete and so I don't throw CELs for the secondary O2's. So we just recently had a cold front go through EL Paso and temps dropped. Last night I hammered the car from 1-2 and the car started to rapidly backfire once hitting boost at about 11PSI (Sounded like machine gun) I'm guessing this is spark blowout (any other ideas). It appears my mid fuel trims have settle to 2% Rear and 4% Front so thats good. But the Low Fuel trim is still way off at -12 Rear and 6 Front. So the next step I will be replacing Spark plugs, while I do this will do compression and gaskets.I might go ahead and replace the front and rear O2 sensors as well. After that Im all out of ideas what is causing this low front/rear discrepancy. You fine gentleman have any other ideas or can diagnose the problem?

BlackSpyderVR4
11-10-2013, 10:03 PM
Ok, been playing with the tuning a little. The front and rear low are always 13% apart. If the front is +5% then the rear will be -8%, if front is +12% rear will be -1%, etc. The mids are great they are about 4% apart. Have them at +2 and -2. I pulled the front spark plugs and they looked great. So how can the front and rears be good on the Mid and bad on Low? The only thing I know of that affects Low's more then the Mid is Vacuum Leaks.

99 vr4
11-10-2013, 10:23 PM
Ok, been playing with the tuning a little. The front and rear low are always 13% apart. If the front is +5% then the rear will be -8%, if front is +12% rear will be -1%, etc. The mids are great they are about 4% apart. Have them at +2 and -2. I pulled the front spark plugs and they looked great. So how can the front and rears be good on the Mid and bad on Low? The only thing I know of that affects Low's more then the Mid is Vacuum Leaks.

Or the MAF or any other intake leak...

BlackSpyderVR4
11-10-2013, 10:39 PM
but the intake pipe y's after the MAF. So any issues with the MAF would screw up both O2's correct? The car is running to smooth for there to be a MAF issue I would think. I will keep eliminating things as I go. The first will be the rear plugs, then rear sensor since its easy to get too.