PDA

View Full Version : Getting good idle with 1200's on AEM Series 1?.



KeithMac
10-22-2013, 09:46 AM
Hello all, has anyone got any good tricks on getting a good idle on big injectors on AEM s1?.

I have played with boost comp/ and the MicroSecBit value but in my fuel table the idle values are too coarse to tune it properly.

If its at 8 (raw fuel value) 1 point down to lean it out is too much!.

How do others go about fine adjustment, its at 11.5:1 but I want 14:1 ideally!.

Thought about manipulating the deadtime but would I be shooting myself in the foot with doing that?.

There must be a way, Emanage ultimate could go -80% to +100% per cell, the AEM seems very low res in comparison?.

mb3000
10-22-2013, 12:40 PM
Your making a full point change? I think my default was a .3 change with my V2.

KeithMac
10-22-2013, 02:09 PM
Yep, say my fuel value at idle is 8, I get a (1/8x100) 12.5% change in fuel!. Ideally my raw fuel value at idle would be 100 to give me 1% changes per 1raw unit but that's not going to happen..

I've read about LD0MPC value but it looks like it makes it even more confusing to tune as that's a rolling adjustment..

mb3000
10-22-2013, 04:41 PM
Any way you can post a screenshot of your fuel map?

KeithMac
10-22-2013, 05:18 PM
There's not much to see yet!, just been trying to nail the starting/ idle/ low load areas.

Just a thought I might be able to try the Throttle Trim to bring it down in a controlled mannor at idle?.

I've read some people have managed to get to stoich with very low raw fuel numbers but can't figure out how myself?.

Lowest MicroSecBit I can get away with is 30 which leaves the idle areas too coarse to tune with the fuel map?.

mb3000
10-22-2013, 05:48 PM
I don't have a V1, but I honestly don't know what you're doing Sounds like you're over complicating things. When you start with the AEM basemap (after doing all of the wizards for injector side, timing, etc) and getting your RPM points set, (letting the engine get to operating temperature, of course) simply make changes to your fuel map where you want your idle to change. On AEMTuner I can visibly see changes in the map with a .05 change in the value of a cell.


Here's a horrible video: (click to watch)

http://i928.photobucket.com/albums/ad128/mb3000gt_photos/th_AEMTunerfinal_zpsfddbaee3.jpg (http://i928.photobucket.com/albums/ad128/mb3000gt_photos/AEMTunerfinal_zpsfddbaee3.mp4)

KeithMac
10-22-2013, 06:47 PM
What injectors are you running?, notice where you're seeing 2% dutycycle at idle, mines down at 0.23!.

If I alter the fuel map in graph or table mode the steps are too extreme with PTE 1200's so I was posting up to find a possible work around (maybe latency manipulation? ).

mb3000
10-22-2013, 06:52 PM
What I showed was simply the start-up .cal that AEM provides. So what you're saying is that if you make a .05 change in your fuel map at idle it is too drastic and goes from 11.5:1 to + 18:1?

mjannusch
10-22-2013, 11:51 PM
What I showed was simply the start-up .cal that AEM provides. So what you're saying is that if you make a .05 change in your fuel map at idle it is too drastic and goes from 11.5:1 to + 18:1?
V1 EMS can't do half steps - we have integer values from 0 to 255. What needs to be done is to dial in the map for the load ranges and then optimize the fuel map to set the correct msec/bit value so that the 0-255 values fit the range of fuel delivery needed in the map. Use a boost compensation style map to be able to get the most resolution. Should be information on the AEM forum on how to do that (most of the information was posted by the Supra guys way back when - I think the main poster's name is "BlkMagic" or something like that).

After the fuel map optimize, your low end values should be higher so that you have more overall adjustability in the fuel map. Each step will be less change.

KeithMac
10-23-2013, 02:37 PM
My MicroSecBit is set at 20 now, can't go any lower.. running Boost Compensation as well.

Got idle to 14 raw on fuel (each step is now 7% fuel change) so I need a little tweak still.

Options are altering latency (loathe to do that really), alter the LD0MPC value, use the Throttle Correction table or rely on O2 feedback to pull it into line (which is a bit of a cludge really), or Boost Comp table tuning.

Think either Throtttle Comp or maybe adjusting Boost Comp may be the best bet..

mjannusch
10-24-2013, 11:32 PM
I did use throttle comp before, for anywhere that's vacuum and only had boost comp above 0 psig. Actually worked pretty well, but I only had 680cc injectors so I didn't run into the resolution problems you are seeing. I'd start there, since you are specifically concerned with idle at the moment. O2FB works pretty well once you get the feedback values tweaked for good response, but certainly dialing in the fuel map and corrections as best as possible is the way to go.

KeithMac
10-25-2013, 02:45 PM
I had a press of "optimise fuel map" and it gave a value of 10 microsecbit and an LD0MPC value of 70, which brings idle into the 70 range (raw value).

Problem with LD0MPC is my fuel map is now practically meaningless as it alters across the load range, I can get my head around boost comp ok but Ld0mpc is just a massive cludge by the look of it?.

Need to get the car MOT'd (inspected), so gone back to my EMU with Maf-t for the time being, started straight up and idled happily at 14:1.

May give the AEM another go as the O2 feedback is excellent and it's nice to command your own idle etc but the fundamental setup of only 255 possible fuel values for the entire map is far too limited for bigger injectors..

Bag-O-Chips
11-12-2013, 06:39 PM
Have you resolved this yet? maybe I can help.

familyMAN
11-12-2013, 11:59 PM
What rpm are you trying to idle at? I could idle 1450's with stock cams, 264's or 280's at 950rpm. No less without afr being erratic. Stock cams didn't help much.

Now on 1000's I can idle much lower but sweet spot is 8-900 with a stable afr and steady idle.

I think my microbitsec is around 50-60. Had to increase it to get the fuel I needed at peak tq in boost. Also boost comp.

KeithMac
11-13-2013, 09:31 AM
I'm still on EMU with Maf-t in blowthrough, idles sweet as silk at 800 rpm 14.0 : 1 afr.

Series 1will be going back on for another attempt but will be after Christmas when I have more time to play with it.

To be honest it's driving that well now on the pte 1200's I'm debating whether to leave well alone now..

Biggest strong point for the AEM for me was 02 feedback but it's running very repeatable afr's open loop with the EMU Maf-t combo..

KeithMac
11-13-2013, 09:32 AM
I'm still on EMU with Maf-t in blowthrough, idles sweet as silk at 800 rpm 14.0 : 1 afr.

Series 1will be going back on for another attempt but will be after Christmas when I have more time to play with it.

To be honest it's driving that well now on the pte 1200's I'm debating whether to leave well alone now..

Biggest strong point for the AEM for me was 02 feedback but it's running very repeatable afr's open loop with the EMU Maf-t combo..