View Full Version : Update on 1st gen green beast and questions
familyMAN
07-06-2013, 07:08 PM
Have some questions that are kinda newb but wanted some advice....
Need better brake pads. Pads turn to mush after a stop or two from 135ish doing 3rd gear logging pulls. Nothing race oriented, just a good street pad that doesn't break the bank.
Need a basic alignment to reduce some understeer but have decent street manners. I am thinking 2* camber up front, 1* in rear and zero toe. thoughts?
AC delete pulley options. I used a stock timing tensioner to tension alternator and it fits great, but the last one started squeeking. Threw on another and now it sounds like I have a supercharger whine. 99% sure its coming from the tensioner. Who has a solution with at least a few thousand miles on it?
Let's get the discussion going!! Thanks!
Update time:Have the car back in one piece and making a hair under 400awhp at 15psi, 8.5* at peak tq and 14* at 7500. Power holds all the way to 7500 when I let off. More boost, timing and probably rpm, coming soon.
Rewind a bit.........Had it all back together a couple weeks ago and was having issues with it bucking at light throttle and then noticed front and rear bank widebands were 5-8% apart. Pulled the coldside piping to TB and did a no boost run. Pulled plugs and two on rear were WAY too clean. Pulled injectors to send back to FIC. Here are the results....
https://lh3.googleusercontent.com/-CBu8iWFNpcY/UdiSS8wk8JI/AAAAAAAABsg/0MEqr0q5FNc/w383-h510-no/photo+%25284%2529.JPG
Could have toasted another motor. Yay:(. FIC said the injector filters were clogged. Bonus is my 1350 (1340 on original flow sheet) now flow almost 1450:). Pulled SS 40 micron filter. Sediment in housing. Cycled pumps a few times to flush. Pulled pumps and cleaned out tank best I could and put in a 10 micron paper filter. We'll see if it lasts. Runs SO MUCH SMOOTHER now!
Here are some pics from today
https://lh6.googleusercontent.com/-9h8vvPk3TiY/Udh-3IeaV3I/AAAAAAAABrk/Rj2W0lsBz0E/w680-h510-no/image+%25285%2529.jpeg
https://lh4.googleusercontent.com/-Qh3LEpLEd0E/Udh-2wZZzfI/AAAAAAAABrg/xXdom7VU4No/w680-h510-no/image+%25284%2529.jpeg
https://lh4.googleusercontent.com/-yAvpwvmsup4/Udh-yUh_aCI/AAAAAAAABrM/OH8ZH5K8vX0/w680-h510-no/image+%25282%2529.jpeg
Even had time to making a little plate today to keep any air from escaping...
https://lh4.googleusercontent.com/-4DTT5LgX1Go/Udh-4fMHndI/AAAAAAAABrs/7duuF4XWkhE/w680-h510-no/photo+%25283%2529.JPG
Taking wife to dinner with the VR4 in a few:D
Unlogic
07-06-2013, 07:39 PM
EBC Redstuff pads are not too expensive and work great on the street.
dbest671
07-06-2013, 10:28 PM
^^Haven't used them on the 3000gt, but that's what I'll be putting on in the very near future.
I used EBC reds on the SRT8 and love them, great stopping power and not to much dust. Might want to upgrade to SS lines as well.
familyMAN
07-07-2013, 12:28 AM
Thanks, I'll look into the redstuff! Pedal feel is fine until pads get smoked from a 3rd gear pull back to sane speeds, so I'll hold off on new lines for now.
Anybody have input on the others?
donniekak
07-07-2013, 12:34 AM
I had red stuff pads on a Dsm I had. They worked great. They also didn't have to be superheated to work, like some race pads.
J. Fast
07-07-2013, 02:02 AM
Hawk HP Plus (new pad compound design) is an excellent everywhere pad and won't fade with continued high speed scrubs.
Regarding A/C delete, I modified the alternator bracket to full swing and finger tension a smaller length belt. Has worked fine for almost two years.
Nice catch on the injectors!
familyMAN
07-07-2013, 11:06 AM
You just have to grind away the bracket for clearance, correct?
Yeah, injectors make me nervous. Could happen again. No rust in tank, just a light dusty coating. I'm assuming it came from my fill station since tank looked spotless before. Running a paper filter now but not sure how it will hold up with e85.
NOMIEZVR4
07-07-2013, 11:54 AM
Congratulations! What motor are you running now? I'm very happy for you :)
familyMAN
07-07-2013, 12:14 PM
Stock 72 TT shortblock, TT heads gasket matched and ported, BC280 cams.
This shorty has some history. Tracked it back thru the forums a few owners to adrenalineVR4 (I believe that's how he spelled it) who bought it new from Mitsu and ran 10's on it with 18gs. Hoping its good luck:) I believe I am the first to have it running since he did years ago.
NOMIEZVR4
07-07-2013, 12:19 PM
Oh did you pick up a set of the new bc cams? I thought you had the dr streets? How are they? Yea I remember adrenaline. .from the 10sec texas crew back In the day. .
I'm trying to dial in my fuel trims currently. .340whp at 11lbs stock rom stock injectors currently. Good stuff!
familyMAN
07-07-2013, 02:27 PM
I have original BC280 cams. So far I really like them. Lost only about 200-300rpm spool in 3rd gear. Power doesn't drop, at all, to 7500. Haven't taken it to 8yet in third but did in 1st and no drop off on VD graph. 272s would start to drop off at 7.
lawdogg
07-08-2013, 02:33 AM
Stock 72 TT shortblock, TT heads gasket matched and ported, BC280 cams.
This shorty has some history. Tracked it back thru the forums a few owners to adrenalineVR4 (I believe that's how he spelled it) who bought it new from Mitsu and ran 10's on it with 18gs. Hoping its good luck:) I believe I am the first to have it running since he did years ago.
That's hilarious! Whenever I sell stuff I wonder where it'll end up. Out of my '94, when I was tearing it apart, I counted parts from at least 5 other members ... LOL!
Anyway, it IS good luck, and I'm glad to see it in action!
familyMAN
07-08-2013, 12:56 PM
Just ordered a two-piece aluminum/steel driveshaft. Shooting to receive it by Thurs so I can make NG Friday evening and Sat. Out of town til thurs evening.
Any ideas on a good alignment?
lawdogg
07-08-2013, 03:48 PM
Need a basic alignment to reduce some understeer but have decent street manners. I am thinking 2* camber up front, 1* in rear and zero toe. thoughts?
I don't know how far a mild alignment like one or two degrees of camber will go to remedy understeer, but your cited specs is a safe setting that won't tear your tires up too bad driving there and back either. I ran -2, -1, 0 toe for years and autocrossed / raced on it without issue, for whatever that's worth!
familyMAN
07-08-2013, 03:55 PM
Thanks for the confirmation! Time to schedule an alignment.
TurboSinceBirth
07-08-2013, 09:06 PM
How many miles did you have on the injectors? Whenever I have a set that sits for awhile without being used it makes me want to have them cleaned to know for sure they'll flow evenly. I never had a issue running the stock paper filter with ethanol. Myths about the glue in the paper filter breaking down and such has never been a problem for me. I have also not had problems with ethanol black goo clogging filters or injectors.
familyMAN
07-08-2013, 09:24 PM
Very few miles. Probably out of car (in ziplock bag) more than in and cleaned twice now. I spoke to FIC about that and they said it was clogged filters from sediment not from sitting out. They could stick from moisture or corrosion for lack of use but that was not the case for me.
The 40 micron SS filter just allowed too much through I guess. Paper it is now and good to know you haven't had an issue. Now I need to watch for leaning out because of clogged filter but at least that will affect all cylinders.
Still think my new station is the culprit. There is another one in town but that is the same brand station as the one I fill at now. May look into drums of e85 or higher. Flex fuel would be handy with drums of e95 for play time and pump gas the rest of the time. Damn you AEM S1!
Oh and travel this week is shortened so alignment scheduled for thurs morning:)
niterydr
07-08-2013, 10:11 PM
Congrats on getting it running again!
familyMAN
07-09-2013, 01:32 AM
Thanks Josh! Getting it running seems to be the easy part....keeping it running is the tricky part;).....All good so far. I just keep fine tuning the cruise map when I'm driving around. Weird stuff going on that I assume is big duration cam related and some sort of weird intake harmonics and/or exhaust reversion. At 2400 rpm rear bank goes way lean and you can feel hesitation. Cleans up around 2600 and then at 3200 front bank goes straight lean. I just added crazy cylinder fuel trims at those rpms and will see what happens. Haven't gotten to take it for a spin yet.
WOT fueling is almost perfect. Still a little leaning out during spool up to dial in, but it is getting close:D....I think there could be big gains with timing, but I'll try to resist until I get it on a dyno.
edit: Hey, are you going to NG? Trying to make it for Fri eve and Saturday. Would love to meet you in person since your AEM map is still the backbone of the tune now. (A lot has changed, but would never have got it started on my own!!! Tweaking bits is easy)
:cheers:
familyMAN
07-09-2013, 08:31 PM
Driveshaft manufactured and shipped today:D
familyMAN
07-13-2013, 12:53 AM
Driveshaft installed and VD graph to compare before and after.....
https://lh4.googleusercontent.com/-qQTpNAjkbJE/UeDM2HP2nZI/AAAAAAAABtU/Ji-ngiX75uw/w869-h652-no/photo.JPG
edit: different road. so take with a large grain of salt....
NOMIEZVR4
07-13-2013, 11:09 AM
Damn..that's a nice bump in power! Wasn't planning on getting one but those are some nice gains!
NOMIEZVR4
09-14-2013, 03:06 PM
yo whats the update??
familyMAN
09-14-2013, 04:13 PM
As you know Nomie, in the last month or so, I have taken out the engine, honed, ringed, replaced a stock rod that walked on pin, new bearings, oringed block, replaced heads with a set of NA I had laying around, replaced trans (used), billet tcase (front and mid), and got it all back together.....
.....AND, It runs and drives:D List of things to fix grows and shrinks almost daily. It currently has about 200 beat-down, break in miles. Oil pressure is fantastic. Haven't done a compression test, but I imagine it is very good also since catch can doesn't get as much action on a pull.
Set cam gears to +1-3 and it picked up some midrange but haven't taken it to redline yet to see if I lost anything. Spool has been slower than I expected. Unfortunately for comparison, the weather has cooled significantly so it will be tough to compare unless the correction in Virtual Dyno is accurate.
Only ~380hp/380tq as of a couple days ago with cam degree adjustment but I am adding a little timing back in at spool up and upper rpms. Off 2-3* in spool up and peak tq vs when I had DR cams so I imagine I can match at these low boost levels. Also need to pull fuel in upper rpms. Went conservative with fuel and timing after making the cam adj, not knowing how it would react. Lots of power could be had at current boost, but will probably start adding boost instead of timing. Want to add some wastegate duty cycle to get it spooling a little quicker. Will shoot for 20psi, and get it dialed in there. Scared to play with timing too much and may just have to get it on a dyno to get the timing dialed in at spool and boost.
Current list of fixes still needed....
Pressure test (damn thing always blows off comp housings with a little pressure.)
Replace TC to driveshaft seal. (at least it seems like it's leaking there.)
Replace carrier bearing support rubber/bracket
Replace one rear shock: ECS connector was damaged when shop replaced springs. Have a used replacement that I just confirmed today works, so I'll get my "Tour" back:D
ALIGNMENT. My tires are about shot because toe is so bad in rear. May do a eyeball method in garage this weekend and get it on a rack this week.
Think that is it:). Considering pulling engine again this winter to re-install A/C. Kept all my stuff, but intercooler kit will need modded to fit. I am getting old and soft!
EDIT: Exactly a year ago, I spun a bearing in my built 3.0, which sent me down a path of poor decisions and broken parts. It is good to be back in the car and driving it. My sons (9 and 1.5yrs) went for a cruise today....great feeling....
NOMIEZVR4
09-14-2013, 04:51 PM
Hell yea...thats a great update...these are the types of updates we should be seeing!! :D I hope it continues to run good and make great power...I know 380whp isn't gonna satisfy you but considering the amount of time you've put into the damn thing, its about time you enjoy it! Whats the boost currently set at?
Keep the updates coming and post some pics after you get her cleaned up!...I should be all back together in the next week or so as well...:)
Drweldin
09-14-2013, 06:54 PM
ive got Wagner ceramic pads and just happen to think to myself today how well the car braked (smooth and grippy at the same time)
Don't forget a good bed in procedure too.
Jimvr4
09-14-2013, 07:47 PM
I don't think you HAVE to pull the engine to re-install A/C
familyMAN
09-14-2013, 08:28 PM
I don't think you HAVE to pull the engine to re-install A/C
You may not have to, but i bet it would be a lot easier to get all the hardlines where they should be and get the bracket on engine. We'll see how motivated I am this winter and maybe I will try without pulling engine first.
ive got Wagner ceramic pads and just happen to think to myself today how well the car braked (smooth and grippy at the same time)
Don't forget a good bed in procedure too.
Yeah forgot about brakes. Until I have to stop from a 3rd gear pull and I smell melted brake pads for the rest of the evening.
You using stock rotors? How well do they do on a hard slow down from 130mph? :)
Jimvr4
09-14-2013, 09:09 PM
You may not have to, but i bet it would be a lot easier to get all the hardlines where they should be and get the bracket on engine. We'll see how motivated I am this winter and maybe I will try without pulling engine first.
Not so hard to do really. With the battery out of the way you can hook up the two hard lines to the evaporator core. You just need the firewall stuff out of the way to route the lines back there. The condensor can go in with the bumper on but obviously the radiator has to be out of the way. Even the bracket should be no problem to add back in as long as your oil feed line for the front turbo doesn't interfere.
familyMAN
09-14-2013, 09:14 PM
Not so hard to do really. With the battery out of the way you can hook up the two hard lines to the evaporator core. You just need the firewall stuff out of the way to route the lines back there. The condensor can go in with the bumper on but obviously the radiator has to be out of the way. Even the bracket should be no problem to add back in as long as your oil feed line for the front turbo doesn't interfere.
Thanks for the encouragement:) I have aftermarket feeds so I can reroute a little if necessary. Most things needed grinding or removal to get the td05 kit to fit so I am just assuming ac would too.
familyMAN
09-14-2013, 11:41 PM
Rented a spring compressor, swapped my megan lowering spring onto my replacement strut and re-installed. GREAT to have tour mode back! No more bouncing all of the place on every bump.
Retractable antenna stopped working so swapped in a short fixed one. Weight reduction;)
JasonY
09-14-2013, 11:52 PM
Carbotech bobcats are the go to pad for the street imo. Very very little dust and work quite well. The hawk HP+'s are an awesome pad, i run them on my FD. But the dust...like no other.
Jason
familyMAN
09-15-2013, 11:10 PM
Current list of fixes still needed....
Pressure test (damn thing always blows off comp housings with a little pressure.) Tried
Replace TC to driveshaft seal. (at least it seems like it's leaking there.) Done
Replace carrier bearing support rubber/bracket Done. Much better.
Replace one rear shock: ECS connector was damaged when shop replaced springs. Have a used replacement that I just confirmed today works, so I'll get my "Tour" back:D Done. Love "Tour"!
ALIGNMENT. My tires are about shot because toe is so bad in rear. May do a eyeball method in garage this weekend and get it on a rack this week.
All but the alignment and pressure test checked off. Found a couple minor leaks, but found MAJOR leak at IAC. Oring failure. Thought I found a replacement in my oring stash that would work, but it was too thick and I cracked the IAC housing slightly while tightening it down. Ordered a new IAC from Ninja and will retest later this week. Should help spool with how much it was leaking!
Carbotech bobcats are the go to pad for the street imo. Very very little dust and work quite well. The hawk HP+'s are an awesome pad, i run them on my FD. But the dust...like no other.
Thanks for the input. BTW, what size RPF1's are you running on your rx7?
familyMAN
09-18-2013, 11:47 PM
New IAC and oring did the trick. Doesn't seem like spool was affected though.
Here is a graph of the progress I have been making. Teal vs green has quite a few changes that I have been making and comparing.....Teal has +1-3 gears, quite a bit more timing on spool up, a little extra timing at 5k on, and some boost leaks fixed.
https://lh6.googleusercontent.com/-zeD425zj-eE/UjphAiIVDbI/AAAAAAAAB1c/AQTh1wr-7Q4/w977-h679-no/NA+Heads+Cams+9-18-13.jpg
I like to compare graphs with smoothing only on 1 so you can see the dips. A bit of work to do on leaning it out. You can see where power dips at 5300 and 6200+ when the afr's get too rich on e85. Don't want to speculate, but there is definitely a lot more in it with leaner afr's and timing based on the gains I am seeing on small adjustments. Timing is only 10* at peak tq, climbing to 15* at 7300.
Want to start messing with boost duty after I get the afrs spot on, but I need to figure out how to keep the solenoid from clicking like crazy at cruise and decel. Sounds like really bad lifter tick or worse, as soon as I turn on boost control. I can get it to stop at idle, but it still does it other areas. Oh well.
kywhitelightning
09-19-2013, 01:49 AM
The dip in AFR only happened on one graph but both graphs seem to follow similar lines in power. Mine seemed to do the same thing in that area power wise(between 5000 and 6000). I added some timing there and it helped a lot. FWIW on pump 93 and meth injection, in that trouble area I was able to get away with 22* at 5500 and pushed it to 26* at 7500.
No disrespect intended but running the timing that low seems like you are really kneecapping it's potential. Pushing the timing should also mess with the lambda reading so if I may suggest a healthy bump in timing and leave the fueling alone at the same boost level. Ethanol's big claim to fame I thought was the ability to run extra timing. Thanks for sharing.
Jeff
familyMAN
09-19-2013, 02:03 AM
Yes, I imagine that there is a lot left on the table for timing at this boost. I can't just dump timing at it and hope for the best as I have essentially zero knock control with e85. (edit: also stock bottom end!) The purpose of the post is to show progress which would go a ton faster if I had a dyno to play with:) As for comparing timing, I believe we are running different turbo setups with likely quite different backpressure, so I cannot use your timing as a basis for mine. (I am td05 housings with td06sl2 turbines).
E85 doesn't like to be under 12:1 with 12.2-12.5 a better target for most cars, so even the other graph is a little rich. I am tuning AEM myself on the road, so I am creeping up to an afr that will get clean pulls (car definitely slows when afr gets too rich). Then I will add a little timing to see what it likes and re-adjust afr as needed. Not going to spend too much time with timing at wastegate boost as I will be raising the boost and have to do timing all over again (starting low and working up.)
Appreciate the insight, just understand that this is a work in progress....
kywhitelightning
09-19-2013, 02:56 AM
Not saying at all to mimic what I am doing just simply suggesting that there is definitely a lot more to be had and pointing out that timing in the 5-6000RPM range is what helped mine smooth out. We all know the stock bottom end will handle a lot more even with room for forgiveness of errors sub 500AWHP. Power over 500 is where I would get cautious. I completely understand why you are hessitant to make big changes as I believe you are just starting over after a huge catastrophie. Good luck to you.
Jeff
NOMIEZVR4
09-19-2013, 09:49 AM
Great update...also just something to keep in mind as you raise the boost(are you planning to do that or just sticking with current boost and just raising timing) the AFR will get slightly leaner as a result, so you don't have to be exactly at 12.0+..to begin with. So big question, what are you trying to end up with power wise? :)
familyMAN
09-19-2013, 11:31 AM
Great update...also just something to keep in mind as you raise the boost(are you planning to do that or just sticking with current boost and just raising timing) the AFR will get slightly leaner as a result, so you don't have to be exactly at 12.0+..to begin with. So big question, what are you trying to end up with power wise? :)
I am running boost comp fuel so afr should stay about the same as I raise the boost which is why it's important to get it pretty close now with a good fuel curve following motor VE.
I am planning to raise boost so that I can get it to spool a little quicker. Wastegates already start to crack at 11psi now. Also, I would think my turbos get into their better efficiency when I am at 25+ psi so to me it makes sense to raise boost instead of timing. I won't be turbo or fuel limited so I don't have to go for td04 timing numbers to make power.
I'd like to enjoy it for awhile at 500-550awhp.
...pointing out that timing in the 5-6000RPM range is what helped mine smooth out......Good luck to you.
Jeff
Thanks and thanks! I'll need it:)
familyMAN
09-20-2013, 04:18 PM
Jeff- added just under 1 degree at 5k and up. Picked up 15-20hp/tq from 5-6200 when I let off. Started raining too much to keep pulling:( Also cleaned up fueling a little, but didn't get to take it to 6400 where it dipped before. So I am sitting at 416awhp/405awtq right now, with what most would consider conservative timing on e85 yet.
I think it's time to get it on the dyno though. Too much anxiety doing 3rd gear pulls on the street while watching gauges, road, and cops. A tuning partner to watch laptop for knock/afr would help, but dyno is the way to go. Pampena is so damn far away!
NOMIEZVR4
09-20-2013, 06:43 PM
nice!! you will be at 500 before you know it..
kywhitelightning
09-21-2013, 04:57 AM
Jeff- added just under 1 degree at 5k and up. Picked up 15-20hp/tq from 5-6200 when I let off. Started raining too much to keep pulling:( Also cleaned up fueling a little, but didn't get to take it to 6400 where it dipped before. So I am sitting at 416awhp/405awtq right now, with what most would consider conservative timing on e85 yet.
I think it's time to get it on the dyno though. Too much anxiety doing 3rd gear pulls on the street while watching gauges, road, and cops. A tuning partner to watch laptop for knock/afr would help, but dyno is the way to go. Pampena is so damn far away!
Wow, that's a lot of TQ for very little timing added. Was there a difference in ambient conditions as well from this pull to the last or is that corrected?
That is the thing I hate the worst with tinkering with this stuff; not enough eyes and it feels like sensery overload for a few brief seconds. Cops, knock, AFR, oh my!!!! Good call on scheduling dyno time. IPS is relatively close to you as an alternative dyno/tuning facility. For the 500-550 goal you spoke of that is where I would take it, especially since you seem to want to do most of it yourself. I would also shoot for a lower target HP wise until the heat of the summer comes back because as we move towards the fall and temps drop, it will give a false sense of security once the heat and humidity of the summer comes back. Base your tune on the absolute worst of conditions not the best. That should help keep it safe.
Jeff
familyMAN
09-21-2013, 09:47 AM
Same intake temps. More humid since it was raining. Not corrected. The road I tune on gives pretty consistent results. The only thing that really affects it from pull to pull is if it spools a early or late and it did not in this case. I would think it was an accurate comparison, but I will do a back up pull.
familyMAN
09-22-2013, 11:59 AM
Big update. Sold the MTC turbos. Need to remove them today. Rear mani is cracked at a new spot so needed to remove rear anyway.
Looking for 14b or 16gs if anyone has something reasonably priced. Better match for my current goals and bottom end.
NOMIEZVR4
09-22-2013, 12:16 PM
dsmtuners
dsmtrader
are both your friends. :)
familyMAN
09-22-2013, 12:33 PM
Can't register on dsmtrader (dsmsource). For some reason I can't see the image verification. Turned off my adblock and no help.
mb3000
09-22-2013, 01:16 PM
You on dsmtuners? I've sourced some good parts from there, and I can be your middleman if need be.
familyMAN
09-22-2013, 01:30 PM
I am on tuners. Don't post much but am searching a little now. PM'd Justin to see what he has. 16gs small, big, evoiii are fairly easy to find. Wanting some cheap fun for a bit. Of course ebay has the evoiii's cheap, but possibly hit or miss on quality. I am thinking 14bs pegged out on e85 would be very interesting. Keep your eyes open for me:D
JasonY
09-22-2013, 02:05 PM
Trevor logged direct comparisons between the 14b and E3's, the difference in spool was almost nil(i think 200 rpms, been a while) but the power greatly in favor of the E3's.
Jason
NOMIEZVR4
09-22-2013, 04:54 PM
indystars is a local DSM site...you can check it out. Not sure if its still around.
chitowndsm.com
dsmtalk.com
P.S. The Username/PW are all the same on the sites.
humananimal
09-24-2013, 07:57 PM
did you decide on the a/c delete problem yet? what i did was simple and used the stock tensioner. i just drilled a hole in the bottom of the bracket so the tensioner bolt can come from the bottom instead of the top and it can be tensioned the opposite way and ran a smaller belt routed around the opposite side of the tensioner from what it was. its been issue free and quiet for about a year.
J. Fast
09-24-2013, 08:26 PM
did you decide on the a/c delete problem yet? what i did was simple and used the stock tensioner. i just drilled a hole in the bottom of the bracket so the tensioner bolt can come from the bottom instead of the top and it can be tensioned the opposite way and ran a smaller belt routed around the opposite side of the tensioner from what it was. its been issue free and quiet for about a year.
Do you have a picture of this?
wingnut
09-24-2013, 08:37 PM
^^^ x2 :D
humananimal
09-25-2013, 06:33 AM
i dont but i can try and get one tomorow
humananimal
09-25-2013, 06:44 PM
idk if you can see it in the picture but the tensioner bolt comes out of the bottom so i could run the belt under the tensioner instead of over5961
familyMAN
10-11-2013, 02:58 AM
Figured I would give some updates....Big changes.....
De-moddeing.....
Sold MTC6954 and bought rebuilt 14b/7cm housings from Justin on DSM tuners
Sold Billet tcase, bought used replacement
Traded 1450 injectors for 1000
Sold twin aero 340's and bought new Walbro 416 (didn't like the idea of two pumps incase one goes out could run lean with another still pumping.)
Fixed...
Welded a new crack in rear manifold
Replaced rear HG. Orings held great but gasket leaked coolant from coolant passage on rear of back bank for some odd reason. All good now.
Wrote a new fuel and timing map for 14bs and 1000cc injectors. Went conservative on both fuel and timing to start and came up with this....
https://lh3.googleusercontent.com/-PY4_sPa8QGI/UleONqQe14I/AAAAAAAAB3k/Jd7esVjG-yc/w874-h553-no/14b+vs+6954.jpg
Blue is MTC6954 when I let the turbos eat with 100% duty cycle. Boost was still climbing when I let off at 21psi (timing was dropping fast in my tune). Green is obviously 14bs. The difference on street feels even more dramatic than the graph. (not 100% apples to apples...slight header leak fixed and a little cooler now.)
Oh and it looks like this.....https://lh5.googleusercontent.com/-M83nyRUQ0nY/UleVoBBqEFI/AAAAAAAAB4o/rLx6HB6oie0/w737-h553-no/photo+%25286%2529.JPG
Tried some high temp gray on the headers. Looks good so far. We'll see how long it lasts.
kywhitelightning
10-11-2013, 05:21 AM
Looks much more fun to drive around in.
Jeff
NOMIEZVR4
10-11-2013, 08:52 AM
very nice!! Eric you don't waste ANY time...hahaha...damn!
AdamVR4
10-11-2013, 11:45 AM
14B's are the shit. What'd they cost you?
Gotta love demodding... but why sell the t-case? You're going to regret that :(
mb3000
10-11-2013, 12:09 PM
+1 sourcing them from Justin over there, you won't have any problems with them. Looks like a nice move towards your current goals?
familyMAN
10-11-2013, 12:29 PM
$525 shipped;) Including the 7cm housings and the turbos look great. Justin media blasts them and coats them. Even surprised me by welding up the wastegate ports since he knew I was external. 14b's and e85 are a good combo so far. Want to start turning them up a hair.
Extremely happy with decision to de-mod so far. (of course, still dream of billet td05's on a 3.7...) Car consumed way too much cash over the last 12months. Wanted to take a step back and create a new foundation to build from. Billet tcase was tough call....I had been wanting one forever, but wanted to put some cash back into the car fund and savings acct and it was a big billet chunk of change sitting there. I don't have a 1/4 mile track close to me now so won't be hitting the track anytime soon. Hope caged 25spline for the street is good enough.
Car gets aligned today and taking it to a local show tomorrow. Actually I will just hang-out at my step-uncles garage and drool over their Mopar drag cars during the show. Then watch some burnouts in front of shop. If I get frisky, MAY try out the antilag for an awd "burnout" and test that cage:D
donniekak
10-11-2013, 03:36 PM
As long as you don't get any wheel hop, the stock t-case can survive some serious burnouts. I had an 18 spline 300m shaft in my car, and no case bracing at all.
AdamVR4
10-11-2013, 03:38 PM
E85+14B's should be extremely capable. Still a 10-second setup in kill-mode.
How far is the nearest track? Mine is about 80 miles away. I'm eyeing a track date in november on street tires, then another in december to actually try (qtp's). I'm even tempted to throw my old DR's on the FRS to shoot for high 14's, I'm jonesing so bad.
familyMAN
10-11-2013, 05:29 PM
Not sure exactly. I know one is 110 mi away. Have an 1/8 track really close but what's the point of that since I won't be launching like crazy.
Post up if you go. Would go with but your track is 950mi away from me:)
familyMAN
10-11-2013, 09:55 PM
Alignment done, finally! So much better. Asked for -2* camber up front and -1* in rear. Zero toe. Ended up with -1.6-1.8 up front and -1.0-1.2 in rear. Basically zero toe. Seems to work well so far but only been blasting around town. VCU works.....nice "rwd" burnouts and slides at every turn from stop sign or light on way home;)
Gave three of the four kids a mini hell-ride tonight:DevilSmile: 1st and 2nd gear are so much more fun now. 3rd is still 'eh. Need more boost. 1st gear gets full boost by around 5500 and pulls to current redline of 7600.
familyMAN
10-13-2013, 06:15 PM
and boom goes the dynamite.....
https://lh3.googleusercontent.com/-HujUxHC9r10/UlsMf0Ild5I/AAAAAAAAB5Y/EGS02qsqIn0/w874-h553-no/14b+543tq+vs+495tq.jpg
NOMIEZVR4
10-13-2013, 06:44 PM
familyMACHINE...:p
kywhitelightning
10-13-2013, 08:49 PM
Nice, why stop at 6000?
Jeff
familyMAN
10-13-2013, 09:53 PM
Out of road. I have another spot to tune on but it is further away and this was just a quick check. Ended up making more tq then I wanted to, so I'll be tuning out that spike and feeding boost in around 5k to redline. Went out a little tonight. Have the spike lowered but need to work on adding more in.
I'll have to wait until next weekend. Unfortunately, I'm traveling all week and I'll be anxiously waiting to get back at it!!!
familyMAN
10-13-2013, 10:52 PM
Here's the one from tonight. Tq "curve" is getting closer to what I want. Nice and flat. Instead of 450, I want to get it in the 475-500awtq range and hold it flat. Staying away from monster 600+tq spikes on stock bottom end. Will get a full pull to 7500 rpm next weekend.
https://lh4.googleusercontent.com/-cvLOBQZdhZA/UltMnaf4qHI/AAAAAAAAB6I/8wHJlzXy-aQ/w874-h553-no/470hp+450tq.jpg
NOMIEZVR4
10-13-2013, 11:11 PM
are you flattening the spike by decreasing timing in that area or just regulating the initial boost spike? And what/how are you keeping the curve relatively flat past 4500-5000rpms? I see boost is increasing gradually as the RPM's rise...is there something else also? great updates BTW..
familyMAN
10-14-2013, 12:39 AM
Both timing and boost control. Timing is around 15* at boost onset, decreases to 10* at peak tq/boost and then increases again to ~15* again by 6k where I let off. You can see that boost increases from 5-6k. 4500 seems to be peak VE. It doesn't take much boost or timing there to make good tq. It also takes a lot of fuel. I'll post my 3D fuel map sometime.
Warning Bench Racing.....
Wishfully thinking I can get it to hold 475tq to 6500 and 450tq to 7k which would be 588hp and 600hp respectively. That should be about everything these little guys can put out but don't think that I have the setup to get it there with stock NA heads and cams and a bit restrictive exhaust. My guess is I will tap out at 550 and call it good:)
familyMAN
10-19-2013, 12:18 AM
https://lh6.googleusercontent.com/-4Ar6I-UkGoE/UmH3ppbVfnI/AAAAAAAAB7E/NMM-sFGtpCM/w861-h553-no/500hp+500tq.jpg
Graph looks good but it doesn't show a little missing I am getting. Tried leaner, tried richer, tried a hair more timing, tried a lot less timing. Nothing helped. Tried new plugs. Helped but not completely gone. The above pull was with 2-3* removed and new plugs. Still missing at 5300 and 6800. I can't go into the 12's afr like most because it breaks up bad. (read the same thing from quite a few on evo forums).
kywhitelightning
10-19-2013, 05:22 AM
What are the plugs gapped at?
I really like the boost control.
Jeff
familyMAN
10-19-2013, 08:04 AM
.022"
I am thinking about getting a mechman alt and upping the voltage. I replaced my alt last weekend because I logged volts and noticed a drop at wot to 12.75v from 13.5 at idle/cruise. New alt was better for the first day, holding 13.25 wot. Now it's been dropping to 12.8. Possibly because I had headlights on (can't remember if 13.25 was day or night).
Been reading some posts and quite a few guys sware by the mechman at 15-15.5v. I already have a DLI but others reported spark issues with DLI as well until upping the voltage. Not sure how so many others get higher without even a DLI.
Yeah the boost control is great. 2-3% increase in duty cycle is noticeable. That pull was at 100% at 3500, then 25% at 3800 increasing to 34% up top. I will try to add some more at 3800 to see if it will help spool without overshooting. Also lowering it a little up top a hair and adding a little timing back in.
Jimvr4
10-19-2013, 01:12 PM
I have an idea on a box that could take battery voltage and crank it up to like 16 volts. It could be used either for the ignition or the fuel pump.
familyMAN
10-19-2013, 01:31 PM
So, is it still in idea phase or something you are already working on? I definitely need something. Isn't that the same thing the boost-a-spark does? Matt M suggested the DLI over boost-a-spark when I was looking for something last year.
Jimvr4
10-19-2013, 01:55 PM
Just an idea at this point, The thought was to still use the DLI but source it with a higher voltage so end up with a boosted DLI. No cockpit control, just a simple box to input battery voltage and output 16V.
kywhitelightning
10-19-2013, 02:30 PM
I sure hope you get this issue sorted out because it seems to me that this car should have a lot more in it especially at mid 20's boost pressure and using the DJ CF in VD. Unless you are smoothing AFR in the graph, I would expect to see some lean areas if there were misfires up top. Add some timing to it and see if that helps, obviously more boost isn't helping and you've already stated that changing the fueling isn't either. 15* up top just seems really weak and I'm curious if that isn't what is causing the issue all together. It sounds like you have good ground work for the power otherwise. Have you checked your cam gears lately?
Jeff
familyMAN
10-19-2013, 03:00 PM
Why would I have to check my cam gears? I have UR gears and cams timed correctly on a stand. Now currently set at +1,-3. Plus I also have good compression which I checked yesterday. I am going to try to lean it out a little more then I tried last night and hope for the best.
I ran 15* before with a little lower boost without issue. Don't see how timing would be the issue then. I tried a little more timing and a lot less timing without much success. This graph had low timing...7.5* at peak tq 11.5* at 5500 and near 15* by end of pull, with new plugs and it was the best of the night.
Think real issue may be the voltage drop I am getting at WOT. Choices are KB Boost-a-spark to raise voltage to coils or mechman alternator to raise voltage everywhere. mechman seems to be more reliable choice based on Matt M's experience with BAS.
Edit: Also, can you explain your comment on CF in VD? No smoothing in boost or AFR.
NOMIEZVR4
10-19-2013, 04:27 PM
Jeff thinks the CF in dynojet mode in virtual dyno is a bit optimistic. He prefers a 1.0 Correction factor based on our location in the midwest and elevation.
I spoke to TSCompUSA, who is the premier EVO tuner on evom, he says he uses the standard CF in virtual dyno. IMO, he is a really good standard to go by since he's probably tuned over 50-100 600whp EVO's. It varies depending on who you ask...If Jeff ever posts his dyno numbers with the default dynojet CF, he would drop a lot of jaws...:D I'll let him explain if he wants...;)
familyMAN
10-19-2013, 05:02 PM
Mine is accurate to Ray's dyno, so it stays as is. Plus it's a tuning tool and just trying to get it to run correctly. Leaned it out a bit, lowered boost a bit and upped timing back to where it was. Little better but it's still there and you can see the power dip. I can try even leaner but if I go too much further it will "break up." No headlights on today, but voltage still drops to 12.8 on a pull......
https://lh3.googleusercontent.com/-yimn7ZOSlaE/UmLji4ao3jI/AAAAAAAAB7w/ijAYbN1DZS0/w874-h553-no/540+vs+500.jpg
Guess I could try more timing instead but that makes me nervous.
familyMAN
10-19-2013, 05:11 PM
Mine is accurate to Ray's dyno, so it stays as is. Plus it's a tuning tool and just trying to get it to run correctly. Leaned it out a bit, lowered boost a bit and upped timing back to where it was. Little better but it's still there and you can see the power dip. I can try even leaner but if I go too much further it will "break up." No headlights on today, but voltage still drops to 12.8 on a pull......
https://lh3.googleusercontent.com/-yimn7ZOSlaE/UmLji4ao3jI/AAAAAAAAB7w/ijAYbN1DZS0/w874-h553-no/540+vs+500.jpg
Guess I could try more timing instead but that makes me nervous.
NOMIEZVR4
10-19-2013, 05:33 PM
don't get greedy..545 is plenty of power man!.leave it as is!!..;)
familyMAN
10-19-2013, 05:45 PM
Just trying to get it to run well. That dip at 6k is from the missing/hesitation/spark blow out (whatever it is!!) Didn't mean to make that much more power. If I set smoothing higher it drops it down a bit. Going to lower boost some more at peak tq and adding a degree of timing. Not touching fuel. Will see what extra timing does. Not sure I'll get a chance to take it out again today:(.
Will also try a pull at wastegate boost and see if it disappears. Man that will feel slow!
NOMIEZVR4
10-19-2013, 05:58 PM
No temp correction?
Theres always gonna be dips IMO...but if its dipping because of actual misfires that you can actually feel in the pull then its a different story and it needs to be taken care of.
familyMAN
10-19-2013, 06:15 PM
No temp correction?
Theres always gonna be dips IMO...but if its dipping because of actual misfires that you can actually feel in the pull then its a different story and it needs to be taken care of.
No temp correction. Air temp and logged temp last night and today are about the same. Yes, I can feel and see it in logs.
familyMAN
10-19-2013, 09:50 PM
Did a couple pulls tonight with added timing. Results are inconclusive. Less break-up but voltage was .5v higher since it is colder. Little misses occurred around 4k and 6k right where boost is highest. Added timing didn't add any power. Dip at 6k is better since missing wasn't as bad otherwise everything tracks the same.
Next step is leaning out even more. If that doesn't solve it, I'll conclude that it's a spark issue and buy a mechman alternator for higher and more consistent voltage.
Chris@Rvengeperformance
10-19-2013, 09:58 PM
your knock voltage look okay?
familyMAN
10-19-2013, 10:26 PM
Looks fine to me. Looks better with it leaned out a bit and more timing. Had a couple spikes when I was testing with it rich.
kywhitelightning
10-20-2013, 02:06 PM
Why would I have to check my cam gears? I have UR gears and cams timed correctly on a stand. Now currently set at +1,-3. Plus I also have good compression which I checked yesterday. I am going to try to lean it out a little more then I tried last night and hope for the best.
I ran 15* before with a little lower boost without issue. Don't see how timing would be the issue then. I tried a little more timing and a lot less timing without much success. This graph had low timing...7.5* at peak tq 11.5* at 5500 and near 15* by end of pull, with new plugs and it was the best of the night.
Think real issue may be the voltage drop I am getting at WOT. Choices are KB Boost-a-spark to raise voltage to coils or mechman alternator to raise voltage everywhere. mechman seems to be more reliable choice based on Matt M's experience with BAS.
Edit: Also, can you explain your comment on CF in VD? No smoothing in boost or AFR.
Before purchasing parts I like to ensure mechanical is in check. You just looked and verified with compression results so, good to go there. Next I would be voltage drop testing the primary side of the ignition system. 12.8V at WOT is typical and .022" is a pretty small gap as is. Adding voltage to the system is a band aid because you shouldn't be having blowout at .022" at mid 20's boost pressure. I didn't start having issues until over 25psi at .025".
That is really smooth for no smoothing on the boost/AFR. Well done!! I would suspect lean spikes in AFR if there were misfires or even incomplete combustion.
Jeff thinks the CF in dynojet mode in virtual dyno is a bit optimistic. He prefers a 1.0 Correction factor based on our location in the midwest and elevation.
I spoke to TSCompUSA, who is the premier EVO tuner on evom, he says he uses the standard CF in virtual dyno. IMO, he is a really good standard to go by since he's probably tuned over 50-100 600whp EVO's. It varies depending on who you ask...If Jeff ever posts his dyno numbers with the default dynojet CF, he would drop a lot of jaws...:D I'll let him explain if he wants...;)
No one would believe 700hp on 750's, not even me. Dyno time is scheduled on a DJ so we will see.
Mine is accurate to Ray's dyno, so it stays as is. Plus it's a tuning tool and just trying to get it to run correctly. Leaned it out a bit, lowered boost a bit and upped timing back to where it was. Little better but it's still there and you can see the power dip. I can try even leaner but if I go too much further it will "break up." No headlights on today, but voltage still drops to 12.8 on a pull......
https://lh3.googleusercontent.com/-yimn7ZOSlaE/UmLji4ao3jI/AAAAAAAAB7w/ijAYbN1DZS0/w874-h553-no/540+vs+500.jpg
Guess I could try more timing instead but that makes me nervous.
Did a couple pulls tonight with added timing. Results are inconclusive. Less break-up but voltage was .5v higher since it is colder. Little misses occurred around 4k and 6k right where boost is highest. Added timing didn't add any power. Dip at 6k is better since missing wasn't as bad otherwise everything tracks the same.
Next step is leaning out even more. If that doesn't solve it, I'll conclude that it's a spark issue and buy a mechman alternator for higher and more consistent voltage.
Keep your comfort zone, by all means. You have done well so far. Keep the progress coming!
Jeff
familyMAN
10-20-2013, 04:20 PM
Thanks for the post Jeff. I have near a 1v drop between battery and coils at idle. Checked that a few weeks ago when looking over coil Hotwire thread. Have the relay and fuse to complete and may give it a go. .018" plug gap didn't seem to make much of a difference today. Haven't done a full pull in 3rd but still get a little hesitation when boost hits at 4k. If the 1v holds true at wot coils are only getting 11.8v at wot. Even with 12.8, that doesn't seem ideal to me though.
familyMAN
10-22-2013, 01:19 PM
Following everyone's advice and leaning it back out. Getting better. Need to lean it some more at mid spool to peak. Feels pretty good, only a little that I feel at 4kish, but logs show rpm drop at several spots throughout rpm range. I'll keep leaning until it starts to break up and see how it looks. Knock volts look better. Rich had a couple spikes.
https://lh4.googleusercontent.com/-VfcyZ2UYCBg/Umaj0EnQTlI/AAAAAAAAB88/ogrtWYSRLVE/w1080-h683-no/2013-10-22
CoopKill
10-22-2013, 01:54 PM
Woot!
Streamln1
10-28-2013, 04:49 AM
12.8 is on the low side even at idle, thats barely charging. I would check the alt. I would like to see 13.3-13.8 at idle and a little more at wot. Of course all the old connections in these cars theres about 50,000 points that can introduce reistance. I just stripped down my entire engine harness to do a clean up / elimination of uneeded crap and the way they did some of the wiring especially grounding is questionable. the 1v drop does seem excessive.
Hows the engine grounds btw? A poor engine ground can throw off a lot of sensors
familyMAN
10-28-2013, 03:56 PM
It's upper 13's at idle, dropping to upper 12's at WOT with old alt or the new one. Also matches other member's, so voltage from alt is not the problem.
NOMIEZVR4
10-28-2013, 06:20 PM
Yeah my alternator is also new and from the same vendor...:p o'reillys..
I should note, I regapped my plugs again today, I was originally using the round gapper from autozone, the keychain one, but someone else recommended a feeler gauge for a more accurate gap. I thought I set the gap to .25 but the feeler gauge was showing .20...so I widened the gap again to a proper .25.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.