View Full Version : Fresh Build + Flash ECU Tuning Experience
sergechronos
06-26-2013, 02:31 PM
Figured I'd make up a thread for it to kind of document my experience with it, other people are welcome to comment and contribute thoughts and ideas. Hopefully Greg can just take a quick read through it for some more detailed feed back from a new user compared to the Chrome ECU Tally and Feedback thread. I will be updating this as I go and figure this out.
Bottom end is new bearings, forged crank, fresh rings, stock rods and pistons. Top end is 1g CAS with factory cams, springs and valves. In short: Mostly stock refresh on the motor itself excluding the forged crank, which obviously was not factory for 91.
Pertinent Mods that impact the ECU/Engine:
Vac Reduction
Turbos are Rob Beck converted 13Ts.
Modified Pampena Single Core Front Mount set up for intercoolers.
Fuel is Walbro 255, not hotwired yet, just the resistor bypass (to try to avoid overrunning the FPR for now, which may be happening anyhow)
Injectors are EVO560s.
Factory MAF with open element filter
Spark Plugs are NGK BKR6ES, gapped down to .28 for now. Will be moving to colder plugs when necessary.
Boost is set at waste gate pressure for now and will be increased after it's running and everything looks good
At the moment, working on getting first start up, so the DP isn't installed in case I have to fix oil leaks or similar..Again.
Using the how to tune thread from Greg, and a couple hours of reading on the Evo forums, as my guide, I embarked on getting this new build running.
Adjusted Injector size to 565cc, and Battery Voltage Latencies to fit what the latencies posted elsewhere for it:
6.01V 1.905
7.98V 1.695
10.03V 1.215
12.01V 0.930
13.99V 0.750
15.97V 0.630
18.68V 0.300
Coolant Temp Fuel Enrichment was also modified slightly to account for the larger injectors. All numbers on the table were reduced about 30% to account for the larger injectors, giving me values of
21
18
14
11
6
5
4
2
0
ECU came with the sizing preflashed for the 560s, however the latency ended up being off when I checked after it failed to start originally while smelling very richly of fuel. So that may have an impact on what follows: Car will turn and almost catch, but not quite run. Pulled the front plugs and they smell of gas, with some dark brown on the insulator and the center electrode is a very dark brown. TPS is logging at about 9, so I will adjust the tension on the cable to increase it slightly, however stepping on the gas pedal to give slightly more air didn't help much. The heads are new, so there was no mark to set the CAS with, I'm going to try advancing timing a bit and see if that helps. I am also going to line the timing marks up, verify that it hasn't slipped time and that the front cams are installed properly (and not reversed) just to rule that out, as well as putting a few gallons of fresh gas into the car as it has been sitting for several months near empty.
Evoscan is giving issues for a J2534 read error, so I need to figure that out to start logging and see what's happening here.
CoopKill
06-26-2013, 02:44 PM
I missed the section on Coolant Temp Fuel Enrichment. Will have to visit that before start up as well. Where did you find that?
Did you run through, and kill the cell peripheries as well?
sergechronos
06-26-2013, 02:59 PM
http://www.3sgto.org/tuning-engine-electronics-ecu-discussions/10777-chrome-v2-tech-manual.html
Post #3:
There are a number of temperature enrichment factors to the base fuel table. One factor is coolant temp. This is the warm up enrichment table the ECU applies to the mixture. I highly recommend at least reducing the values in this table if you are installing larger injectors.
Example: If you're running 680s, reduce the trim by half since they are 2x the size of stock injectors.
Chris@Rvengeperformance
06-26-2013, 03:12 PM
It is good to adjust those tables with larger injectors, but I found the car ran great on the 560s just changing the latencies and scaling. With the 1050s I had to make big changes to those other tables.
I'd clean your plugs and do a quick boost leak check since this is a new build. The car will actually start with some pretty ridiculous settings, so usually when you have this much trouble getting it to run it is something mechanical.
sergechronos
06-26-2013, 03:37 PM
It is good to adjust those tables with larger injectors, but I found the car ran great on the 560s just changing the latencies and scaling. With the 1050s I had to make big changes to those other tables.
I'd clean your plugs and do a quick boost leak check since this is a new build. The car will actually start with some pretty ridiculous settings, so usually when you have this much trouble getting it to run it is something mechanical.
Not sure what size injectors Bill is running, but yeah generally not necessary for as small as these 560s. Just figured since it smells rich, couldn't hurt to take a bit off of that table just in case. Just picked up fresh fuel, although I think you're right about it being something mechanical. Going to try fresh fuel first, then go from there. Fuel is so low that the light is on, and it's been sitting like that since December, so can't hurt. I will be doing a boost leak check for sure though, probably have some massive intake leak somewhere. Possibly from the upper to lower plenum, had a bad leak from there before.
Well, checked something...Issue is coming from the front head for sure. After cranking the car a few times, the rear exhaust is hot/warm to the touch, the front exhaust is just at ambient temperature. So clearly I'm either not getting spark or timing is off on the front head. Going to rotate it back to TDC and check the timing, make sure that I didn't get the cams reversed on the front.
Update: Checked the timing and cams, still accurate. So it would seem something is going on with spark delivery for the front 3 cylinders. I'll be testing the plug wires and go from there. Perhaps, coincidentally, that the plug wires failed.
Update to the update: All 3 plugs are firing. So I think I'll need to figure out a way to get the logging function working
http://i12.photobucket.com/albums/a218/majwoody/IMG_0079_zps9dea6ed7.jpg (http://s12.photobucket.com/user/majwoody/media/IMG_0079_zps9dea6ed7.jpg.html)
Plug 1
http://i12.photobucket.com/albums/a218/majwoody/IMG_0080_zps1f3afeb6.jpg (http://s12.photobucket.com/user/majwoody/media/IMG_0080_zps1f3afeb6.jpg.html)
Plug 3
http://i12.photobucket.com/albums/a218/majwoody/IMG_0081_zps86b3ee05.jpg (http://s12.photobucket.com/user/majwoody/media/IMG_0081_zps86b3ee05.jpg.html)
Plug 5
The deposit/fuel wipes off pretty easily so shouldn't be that bad. The firing is fairly violent. Going to see if I can get my digital camera to record a video and work and I'll see about getting it uploaded. Possible it could be misfiring on the front cylinders, going to see about opening the gap back up and if that helps.
http://s12.photobucket.com/user/majwoody/media/DSCN1139_zps30b6d315.mp4.html
This would be with my foot on the throttle to keep it running. Actually around half throttle here, and you can't really tell from the video sadly. Ignore the tach, had the needle off and need to reset it, I just put it back on there so I wouldn't lose it for now.
Greg E
06-26-2013, 03:43 PM
I'll make a post tonight when I get home and can show some screen shots.
sergechronos
06-26-2013, 06:56 PM
Okay, got it to make some logs here. Adjusted the throttle cable, still at 9.4. RPMs are maxing out at around 500-600 while trying to crank. Rear O2 voltage is around .859 to .898v while at that kind of RPM during the rough ass idle. Front O2 is at like .2v. So, o2 could be busted, but still doesn't explain why I'm not getting anything from the front cylinders. Would imagine that without it actually igniting properly that it should be super rich.
Timing is 5 degrees through out (unless I should be logging true timing instead of timing advance).
Coolant temp is registering at -56. Which is impossible obviously..Especially being as it's you know..90 degrees outside. Sensor is plugged in, but I'll double check it. Could be broken. I did replace the sensor for the temperature gauge, but I doubt that Coolant Temp pulls its number from that, and I'm still not sure that it's what at fault for this starting issue.
While trying to crank, 2byte Airflow alternates between 88 (high) down to 28, then back up.
Going to have to figure out what the deal is with the front bank though.
Greg E
06-26-2013, 07:28 PM
Coolant temp is registering at -56. Which is impossible obviously..Especially being as it's you know..90 degrees outside. Sensor is plugged in, but I'll double check it. Could be broken. I did replace the sensor for the temperature gauge, but I doubt that Coolant Temp pulls its number from that, and I'm still not sure that it's what at fault for this starting issue.
Go to the Fuel section and look for the table labeled Coolant Temp Fuel Enrichment. Set the entire table to a correction factor of 1.000.
If your car starts without fouling, the sensor is your problem. :)
sergechronos
06-26-2013, 07:37 PM
Go to the Fuel section and look for the table labeled Coolant Temp Fuel Enrichment. Set the entire table to a correction factor of 1.000.
If your car starts without fouling, the sensor is your problem. :)
Will do. Have another sensor around here somewhere I can throw in. Found my TPS wasn't seated properly. Pulled it, cleaned it and reseated it and I get readings on it now. le gasp. Somewhat ironically, the actual TPS value is...9.43 lol Amusing. But now it reacts with throttle movement. Huzzah.
Timing is set at an insane 61 degrees. Hoping that it's related to the coolant temp thing and that it'll go away. Rear O2 shows .95648v with the ignition on, buyt not cranking. Removed the front O2 from the precat, I'm getting .01952V on it in open air.
Voltage has dropped down to 11.4V from all this cranking today, so I'm going to put it on the charger for the night and let it get back up to normal before I try to flash it..Or at least close to it. May just say to hell with it and take it to Autozone tomorrow and have them replace it under warranty. From the brief period I had it running tonight, seems that I solved the oil leak on the turbo return line, but not on the oil pan itself. :( So I'll try to get that resolved tonight/tomorrow.
Greg: Anything else I should/could log to get a better idea of what may be happening with the front bank in case the coolant sensor doesn't work?
Swapped the coolant sensor, and so long as I keep my foot on the throttle, it will mostly maintain idle. If I kept the throttle at about 20%, idle stayed around 800rpms more or less. Very rough idle, but the plugs didn't smell quite as bad of fuel as before.. Going to bolt everything down that I've taken off in the last couple days, and give it a boost leak test after. Also going to try setting the throttle per Greg's instructions for Chrome. Didn't mess with the TB, so it shouldn't be too far off, but clearly something is. Definitely idles far better now with the different sensor than the one that had been in it, but that's not saying much.
http://i12.photobucket.com/albums/a218/majwoody/Untitled_zps9fc31673.png (http://s12.photobucket.com/user/majwoody/media/Untitled_zps9fc31673.png.html)
Possible that given more time idling it would've burned up any excess fuel and fixed the idle on it's own. When I bolt everything up, that will include the DP which has my WBO2 (mounted on the front pipe no less) so that should shed some more light on the AF of the front side.
sergechronos
06-27-2013, 08:40 PM
Resealing the oil pan and the front turbo return line today/tomorrow so it'll be a few days before I get to it. I will be reassembling it all, and using a new O2 sensor on the front to get logs and see what's happening.
Update 6-28 11:41am: Found it this morning. Front cam slipped a tooth (or two) during one of the start up attempts or during the first fire up. Going to have reset timing and hope that I didn't bend valves.
sergechronos
08-17-2013, 06:50 PM
After a delay due to a trip to NY, I fixed timing and put it back together. Turns out the 3SX oil pan is crap and leaking oil so I am getting an OEM one to replace it, in the mean time I'm keeping a close eye on the oil level and working to get it running properly.
When I attempt to log with Evoscan now (it was working before I left), it connects for a few seconds then gives me the J2534 error. Going to uninstall and reinstall Ecuflash and Evoscan to verify that's the issue. It will actually crank and start. Am I to assume the values I see in the main Evoscan window prior to logging are live values? If so, my TPS doesn't change regardless of whether or not my foot is on the floor (9.7%) and my timing shows at 61 degrees. Since I can't log, not sure if those values actually change or not.
When I start the car, it idles at 2.5k-3k RPMs. I need to clamp down IC hoses still, as they are all connected but not clamped, which I'm sure doesn't help the case and I believe that brake booster needs a clamp as well since I hear air from there. Car sounds a bit rough at idle (I'll try to get a video tomorrow or something), but at least it runs and more or less stays running on it's own after a few seconds.
Greg E
08-17-2013, 07:38 PM
If EVOScan doesn't connect you wouldn't see any values...
sergechronos
08-17-2013, 07:40 PM
It connects until I ask it to datalog, then it gives me the J2534 error.
Edit: When I click to start logging, it logs for a couple of seconds, then gives the error and stops logging.
Edit #2: Seems that my issue is not software/laptop side, but is instead related to the electrical system on my car. The same issue that prevents the battery power from reaching the AC or CD player. While the effects on the AC are that it has no memory, it prevents the CD player from turning on and prevents the Openport from getting the battery power. Removing and replacing the fuse responsible for these functions netted no change. Clearly I have a short or broken wire somewhere in the system so I will have to trace this to find the cause of the problem, this may also explain why my battery(s) die in less than 48 hours. Will try to fix this issue then try again.
Edit #3: Evoscan gives me varying battery voltages when I attempt to test something (this is with the battery fully charged plus a charger attached to it) when it tells me that there's less than 5v and I need to connect it to the car. Voltage is around .196-.250. Possibility of just a shitty connection from the engine bay to the fusebox/OBD1 port (not sure which it hits first) or wire being broken in it's sheath? The fact that the voltage is low @ the OBD connector/fusebox tells me the issue is either at the fusebox or a connection between the box and the battery (battery has 12.5v). Not sure how many connections it goes through before that, but have to imagine as the dedicated voltage for the interior it can't be many. Will spend some time tonight reading the electrical diagrams for the car to figure it out.
Edit #4: Quick scan of electrical diagrams looks like the alternator fuse needs to be tested, as well as a couple connectors on the right side of the dash. I've had issues out of one of the connectors there before, may need to pull it back out and check to make sure pins are still seated properly. If not, then it's getting crappy contact, and that would explain the batt power coming and going.
Greg E
08-17-2013, 10:48 PM
Anxious to see this resolved. Never ran into an issue like this before.
sergechronos
08-17-2013, 11:26 PM
It's definitely some kind of wiring issue related to the "always on" power for the system. Basically gives me the same effect as the IOD jumper being pulled out. Not related to the tuning stuff.
Greg, as an added note, one of the previous owners had a rather intrusive keyless entry or something wired into it and appeared to be poorly done, so this may be related.
Unfortunately have to fix this before I can get back to work on diagnosing the high idle issue. I doubt this an issue that many other people have or will run into though. I did clamp down the IC pipes, with a very minor change. It'll go to 2500rpm, then up to around 3200-3500, then stumble to 2000rpmish (maybe lower). Tach may be off (always has seemed to be) so I will reset that via Evoscan once the wiring is fixed as well. It definitely gets high enough that I can hear the turbos spooling.
Once I fix it I will verify that the TPS and MAF are working properly, check to make sure the cruise control was put back together properly as well. Throttle body needs to be rebuilt eventually, however I didn't have this issue before I rebuilt everything so I don't want to introduce any more variables into the mix. Once I confirm sensors are working properly, I will start working my way from there. From the brief time the Evoscan was connected and logged, TPS showed no change and coolant showed 78 degrees. MAF stuff read zero since the car wasn't on at that point. Next time I get it to connect at all I'll jab the pedal a couple times and see if I do get a response from it. I also will be pulling the fuel pump out to verify that the filter is still in good shape, and will probably drain the fuel that's in it as it's low enough for the light to be on, but has been sitting since around December until I added 2-3 gallons about 2 months go.
sergechronos
08-18-2013, 02:00 PM
Confirmed power is not/barely making it to the always on pin of the OBD port, as well as of course the radio and AC. May have to remove the dash to get the junction box out to inspect the backside and start tracing the wire.
sergechronos
08-18-2013, 04:53 PM
http://s12.photobucket.com/user/majwoody/media/M2U00043_zps5988894e.mp4.html
Quick and dirty video of what I'm getting at idle, this is with no DP on. The changes in RPM are all from the car itself, no throttle manipulation on my part except when it was about to die. Checked for boost leaks yesterday and found nothing, so assuming a sensor at this point. Once the electrical situation is sorted out I'll know for sure. A bit slow starting due to (I presume) a hole in the fuel pump hat or a bad FPR. Have a new pump hat coming and will be replacing the gasket. If that doesn't work, will replace the FPR with an AFPR.
sergechronos
08-18-2013, 06:46 PM
Well, managed to get 12v to the wire while wiggling and jiggling stuff around the fuse box. Decided to strike while the metaphorical iron was hot and logged a start up. Seemed that this time after a few other attempts running it it settled down a bit and idled down around 1500rpms-2000rpms. Unfortunately didn't think to switch what I was looking to log over to the idle/start up relevant information. I'm going to try to mess with the wires and see if I can get it to work again if there's anything in particular that you think would help figure out the issue Greg. I figure the RPM and TPS, 2byte airflow, target idle rpm, ISC steps, and injector latency. Anything you think I may be missing that I should add to that list?
Here's some of what I'm seeing. Coolant temps are at 78 degrees at the start, up to 94 degrees when I shut it off. RPM is orange and TPS is red in all of the following:
http://i12.photobucket.com/albums/a218/majwoody/AirflowRPM_zps2d507bd8.png (http://s12.photobucket.com/user/majwoody/media/AirflowRPM_zps2d507bd8.png.html)
Air flow HZ is purple. At around 1500rpms airflow is reading 125, at 2000rpms it's at 118.
http://i12.photobucket.com/albums/a218/majwoody/TimingRPM_zps03675c93.png (http://s12.photobucket.com/user/majwoody/media/TimingRPM_zps03675c93.png.html)
Timing advance is pink, it's between 30-40 degrees once the RPMs stabilized.
Also logged during this time: front and rear O2s, injector duty front and rear, pulse width front and rear, front and rear o2 feedback trims. Still, need to check the idle switch and see wtf is happening with the IAC. MAF airflow seems really high to me. Anticipated something closer to 70-80hz at 1500rpm. The logs dont show the idle position switch, but the ISC steps starts around 110ish and tapers off to 60 by the end of the log.
Greg E
08-19-2013, 08:07 AM
I think you're looking at things too closely. Take a step back and return to basics:
Intake leaks
Throttle body leaks
Have you eliminated the PCV valve?
That sort of thing. Clearly the ECU works fine.
sergechronos
08-19-2013, 05:13 PM
Ran a boost leak test the other night with no leaks heard. Found today while replacing a filter on it that something got inside and clogged it all up. Once I fixed that and checked again, I had a leak from the front turbo coupler and a leak from the throttle body. Throttle body gasket was new but when I went to take it off the bottom part looked kind of wet and tore. I ordered a new gasket that should be here Wednesday and I will be spraying it with some copper gasket maker to help ensure that it's no longer a problem.
sergechronos
10-01-2013, 10:28 AM
As an update for those not following the build thread I finally started: Upon replacing the throttle body gasket, found that I had a big leak from the upper to lower plenum. Had been an issue before because the threads are stripped. Just bought another lower mani (cheap as it is to helicoil honestly), and went to install that this weekend. While installing it, I found I had a decent puddle of coolant under the water pipe in the valley. Had to take everything off the passenger side of the engine and, sure enough, found that there was a small cut in the o ring. So ordered a new set of gaskets for the waterneck and such, as well as a new o ring. Should be here by the end of the week so I can pressure test again. Once the top side is free of leaks I will be replacing the oil pan and oil return lines to eliminate my oil leak, then should be free to button it back and take it out on the road to break it in. I have also installed an AFPR to better control fuel pressure and ditch the factory resistor, should be beneficial when I start working the boost up. Also converting my fuel hat over to AN06 fittings and line to the hard line. The factory metal line on the hat had a small kind of bend in it that I just wasn't comfortable with. While it may have been fine, I just didn't want to risk it when I start demanding more out of the car.
At this time, my plans have changed slightly. I picked up a set of 880CC injectors and a Walbro 400 E85 pump as there is a station near me that now carries E85, and one near the school that does as well. I won't be running E85 until after the motor is broken in, but it is in the future plans (especially with the changes coming to Chrome.) I don't think starting it with the 880s will be a huge issue, but remains to be seen.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.