PDA

View Full Version : Getting a heart transplant.....



DrGonzo
06-24-2013, 10:56 AM
Well atleast my Stealth is!

So this past Friday I spent some time working on the Stealth. Installed the last Solid motor mount and swapped out some parts for some Hydro Dipped ones. I also installed the front timing cover that I dipped in the funky skulls to show off at our Friday Night local car meet. I get everything swapped out and go to start the car. I hear a god awful noise and immediately turned off the car. I knew right off the bat it was the timing belt and though that it had broken. I pulled the covers to find this:

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1077.jpg

I told myself months ago that if anything happened to this motor I was just going to swap it out for the block I had been working on. You can find that engine build thread here: http://www.3sgto.org/3000gt-stealth-gto-related-topics/10784-new-engine-build-death-10-1-a.html

So Sunday I started to pull the engine. it would have only taken a couple hours if the weather would have cooperated. it rained on and off and since I don't have a garage it is all done in my driveway.

Engine pulled:
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1079.JPG

And sitting in the driveway:
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1080.JPG

From this point I will be pulling items off this engine like turbos and such and swapping them over to the new block. All parts will be cleaned and repainted as needed but for the mast parts things are in good condition and will just be swapped over.

While the engine was out I pulled the covers to see what caused the issue with the timing belt. I originally though the timing cover hit the belt as the hole is right inline with the nub on the underside of the front timing cover. Upon pulling the lower cover I found the culprit....

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1081.JPG

I thought that nut fell down in between the heads into the bottomless pit, guess I was wrong. I also found that the metal cover that goes between the heads was missing which is how it made it's way into the timing belt area to begin with!

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1082.JPG

I will say this, I have a lot more trust in Gates timing belts now. The belt has a massive hole right though it but it belt never broke or slipped. I personally believe that these gates belts are just as good as OEM.

If the weather and time works with me this week I may have everything cleaned and and the new engine dropped in next week. I have a few things I will be addressing during this time so it may be a month or so before the car is back on the road.

j2k4
06-24-2013, 11:14 AM
In for progress postage. :)

Alan92RTTT
06-24-2013, 12:05 PM
If the Tbelt did not skip/jump why not just replace it and move on? (I'm assuming I'm missing something)

DrGonzo
06-24-2013, 01:05 PM
1. I did't want to put anymore money into that engine.

2. The time it takes to do a t-belt with the engine in the car I had the motor pulled.

J-Groove
06-24-2013, 02:41 PM
Crazy the belt held like that!

Now to go read the thread on the engine's details.

-John

Uniuno
06-24-2013, 02:50 PM
Plus side of doing it in the driveway like that; look at all the space you have!!!

Can't wait to see what you can do with the new engine

Alan92RTTT
06-24-2013, 02:58 PM
1. I did't want to put anymore money into that engine.

2. The time it takes to do a t-belt with the engine in the car I had the motor pulled.

AH, no need to rebuild just based on what happened, it just fits your personal goals.

sergechronos
06-24-2013, 04:11 PM
If you need another one of those metal covers for between the heads (not sure if you have an extra for the new block) I've got one I'd sell you for pretty dang cheap.

DrGonzo
06-24-2013, 04:56 PM
If you need another one of those metal covers for between the heads (not sure if you have an extra for the new block) I've got one I'd sell you for pretty dang cheap.

The new engine has all of the covers including that one that was missing.

IDK at what point I removed it and never re-installed it. I have had that engine now for almost 15 years and through multiple rebuilds. I guess at one point I forgot to put it back on and just never noticed it missing.

Jimvr4
06-24-2013, 05:13 PM
I guess at one point I forgot to put it back on and just never noticed it missing.

Or you already had the cam gears on there and didn't want to take a step backwards :p

green-lantern
06-24-2013, 08:46 PM
AH, no need to rebuild just based on what happened, it just fits your personal goals.

Exactly, Hes been looking for a forced upgrade since I've met him. I can relate

Chris@Rvengeperformance
06-24-2013, 09:55 PM
wish I had a spare motor

wingnut
06-24-2013, 10:42 PM
Or you already had the cam gears on there and didn't want to take a step backwards...

lol, agreed...been there, done that :D

DrGonzo
06-25-2013, 11:29 AM
So yesterday I got all of the parts off of the old motor and I'm working on getting them cleaned up. Looks like everything is in great condition and some just need a light re-spray. Got some parts soaking in cleaner and they will just need to be scrubbed clean. I have to go through my gasket inventory to ensure I have all gaskets to get it back together and make sure I have enough braided lines and AN fittings for the coolant lines to the turbos. I may be able to drop the engine back in come this weekend unless I run into snags, which will most likely happen...LOL

DrGonzo
06-26-2013, 05:41 PM
Last night progress!!

I found out that the 3sx solid pulley I had did not have the damn base timing mark on it. Little hard to set the timing without that mark on the pulley....

I mated it up to a stock on and filed in the groove.

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1084.JPG

I also realized that this engine had a second gen rear valve cover so I could actually use the timing covers that I dipped. Luckily I found that the covers are not what damaged the belt on the other engine. It was the nut that fell into the timing area.

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1085.JPG

Fuel rails and DSM 450cc injectors installed. Stubs all installed for the rails and upper intake plenum. Makes it much easier to work and not have to worry about loosing the bolts. If I lose a nut I have a whole bag full of them. Just have to make sure they don't fall into the timing area again....

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1086.JPG

Electronics moved over and working on getting the AN coolant lines plumbed. They will be finished once I have recoated the exhaust manifolds and mount the turbo's.

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1087.jpg

Tonight I have to respray the exhaust manifolds and pre-cats. I use VHT High Temp paint made for exhausts. It is good up to something like 2000 degrees. It is on the manifolds now and has held for years. Just respraying them to clean them up is all. The front is the main one. I pulled it last year to fix a crack and used the engine paint not exhaust paint. Needless to say it burned off in about 10 mins leaving the fresh weld exposed. Which looked horrible when you looked at the manifold.

DrGonzo
07-01-2013, 10:35 AM
So this weekend we very busy for me. I dragged the new engine out of the shed where it has been for the last year or so now. Had to use boards to get it out front as it was all muddy grass from the shed to the driveway.....

Finished buttoning up the engine of all the minor things and got the new engine dropped into the car. That is as far as I got. The rain has been really bad here lately and the humidity is horrible. In the process of getting parts swapped over I ended up breaking my Temp gauge sender and the ECU coolant sender. So I had to order both new parts. I only installed the engine the trans is not yet installed. I still have some work to do on the trans and I needed to get the engine installed due to the rain.

http://3s.gonzoinc.com/albums/userpics/10002/Engine_Lift.jpg

http://3s.gonzoinc.com/albums/userpics/10002/engine_Installed.jpg

The front valve cover is temporary as I am working on getting the permanent one completed.

green-lantern
07-01-2013, 01:09 PM
Looking good man, keep it up.

CoopKill
07-01-2013, 02:37 PM
Awesome! So many builds going on right now. Great to see.

Jimvr4
07-01-2013, 03:25 PM
Looking good! Can't wait to see what you do with the valve cover / plenum.

DrGonzo
07-31-2013, 09:05 AM
Update time....

Weather has not been the best so it has taken me far longer to get the engine back together, but it has kept me inside enough to get some other things done. I'm sure most of you have seen the hydrographic parts I have been doing.

Well yesterday I realized I was 95% done. I was only waiting on the two reducers for the pre-turbo pipes to come in and I could finish everything up. Everything else is done.

Here is how it looks as of yesterday.

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1144.JPG

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1145.JPG

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1146.JPG

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1147.JPG

If I get the reducers in by the end of the week I hope to have the engine fired up this weekend.

Granny
07-31-2013, 10:35 AM
If it runs as good as it looks! Wow
Beautiful work

DrGonzo
08-05-2013, 09:09 PM
So finally got everything installed. Filled the oil and coolant. Had to fix a leak in the coolant neck. Today I primes the engine and fired it up. Not happy with the noise it is making. When I rev it up at the throttle body it back fires pretty bad. Checked the plug wires and found a rear bank plug is not firing. I'm hoping the noise and back firing is being caused by that cylinder not firing. Here is a video of the fist start up.


http://www.youtube.com/watch?v=0-Ews24aKig

mb3000
08-06-2013, 01:07 AM
Almost sounds like something more. Keeping my fingers crossed for ya.

2faststealth4u
08-06-2013, 01:45 AM
You make it all look easy

n2nsanity
09-02-2013, 01:28 AM
One of the 450's cutting out? Aren't you using those nice connectors without the p.i.t.a. metal clips? If so, possibly bad splice? It's always the little things...


BTW, it looks amazing. I see some trophies coming your way.

DrGonzo
09-02-2013, 12:54 PM
Guess I forgot to update this thread...


So I pulled the rear valve clover an found 4 rockets had fallen off due to collapsed lifters. Guess they didn't hold the prime over the last 6 months. I went to re-install them and found one of the valves was dragging so looks like it is bent.

I decided I'm not killing myself over the last couple weeks to get it ready for BRG so it sits outside now with a bent valve. I'll get it fixed when I get back from BRG.

On a good note when it was running the oil pressure was awesome...LOL

green-lantern
09-02-2013, 02:19 PM
Bummer

If it makes you feel any better, my 3000 isn't going to make it to BRG ether. :/

DrGonzo
09-02-2013, 02:43 PM
Yeah I was pretty bummed about it. I did sort of push things last min on getting it all together. But it is not stopping me from coming so that is good.


What's going on with yours Paul?

n2nsanity
09-02-2013, 07:36 PM
You call that last minute? :p
When I say last minute, I literally mean the last minute before I'm supposed to leave, lol.

99ishVR-4
09-03-2013, 09:11 AM
That sucks about the bent valve but your engine looks great. Very impressed with the CF hydrographics.

green-lantern
09-03-2013, 12:50 PM
Yeah I was pretty bummed about it. I did sort of push things last min on getting it all together. But it is not stopping me from coming so that is good.


What's going on with yours Paul?

I think the OBX LSD is causing me trouble, it's a trans problem anyway. It was making a nasty noise when I let off the throttle. A few metal pieces in the fluid when I drained it.

DrGonzo
09-03-2013, 03:14 PM
Aww that sucks!

Transmission is the next thing getting rebuilt once this engine is back up and running correctly.

DrGonzo
09-14-2013, 07:50 PM
So what we assumed was a bent valve on my new engine, turned out to be rust on the valves themselves causing them to stick and the rockers to fall off. I don't know how rust got in there as I coated the valves in motor oil when I built the heads. So I'm going to clean all the valve and valve guides and get this engine back together.... Eventually!!

n2nsanity
09-15-2013, 12:26 AM
Great news :)

DrGonzo
09-16-2013, 11:47 AM
So got the head off on Saturday. Found that all of the valves where the rockers fell off had rust on them. Only the one was bad enough to cause it to stick really bad. Looked at the valves and pistons and looks like there was no contact so they should all be good. I'm waiting on a Keeper install tool which should be here tomorrow. I'm using a home made tool which is great for dis-assembly but a pain trying to get the keepers back in. So I should be able to finish the head off tomorrow and work on getting it back together this week.

DrGonzo
10-26-2013, 08:12 PM
So again, I have been busy and not keeping this thread updated.

So I got the new tool to find out it is good for taking keepers off but not putting them back together. I ahve anotehr thread somewhere about it. basically it tells you to use a hammer to set the keepers, well.... I broke a valve doing it that way!!!

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1175.JPG

so I'll never use that tool again to install them. Swapped in a new valve and got the head re-installed.

Car was still running a little rough so figured it was base timing. tried to set it and the notch was way over past the marks and I could not get it to lower any further. Took off the cam pulley and realized when I make the mark for it on the 3sx aluminum pulley, I did it wrong...LMAO!! So earlier I posted a pic on how I made the mark:

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1084.JPG

Well face to face like that causes it to be off by like 30 degrees. Corrected the timing mark issue and got it all back together.

Now the engine was running rough again and smoking. Pulled plugs and two plugs were coated in oil. Figured I had an oil leak from head gasket or rings. Did a leak down test and they all were 3-5% leak down. so they were all in great condition. Pulled the valve covers again and found a rocker on the read head slipped to an angle which caused the intake valve to not close all the way. got the rocker fixed and the engine back together and now she idles nice and smooth... but still smoking. When I hit the throttle is smokes really really bad... at this point i am hoping the smoking is due to me not breaking in the rings yet.

I have a small coolant leak to fix, Find some exhaust leaks and get a new Alt-A/C Adjust pulley as mine is squealing bad, then I will get her on the road to break the engine in.

n2nsanity
10-26-2013, 08:47 PM
Glad to hear you're getting back on track with this thing.

And yeah, give her hell to break it in :)

wingnut
10-26-2013, 08:58 PM
Yea, i dont know when/where the hammer strategy came from...

...but its definitely not the suggested method :(

CoopKill
10-26-2013, 09:18 PM
So Have I told you about my experience with excessive smoking on first start up? :suspect:

wingnut
10-26-2013, 09:48 PM
So Have I told you about my experience with excessive smoking on first start up? :suspect:


lol :D im sure theres a thread about it somewhere...

DrGonzo
10-26-2013, 09:57 PM
So Have I told you about my experience with excessive smoking on first start up? :suspect:

Wasn't yours due to a plug not being removed from a turbo drain....LOL I'm sure it's not my issues here.

wingnut
10-26-2013, 11:46 PM
Wasn't yours due to a plug not being removed from a turbo drain....LOL I'm sure it's not my issues here.


http://skeptikai.com/wp-content/uploads/2011/11/Achmed-the-Dead-Terrorist-silence-I-keel-you.jpg

CoopKill
10-27-2013, 12:10 AM
^^^ Cough ^^^

DrGonzo
11-18-2013, 10:16 AM
Well, I finally got her on the road for a bit!!! Drove around the neighborhood and down to the gas station twice this weekend. So probably about 10 miles on her. Idle is nice as smooth now. No leaks that I can see so far!!

Things I need to address:

I need to finish bleeding the power steering as I seem to have a stuck bubble somewhere in the system as I get random steering whines when turning.

Brakes need some love, There are a bit loose due to not bleeding them all the way and the rotors having a lot of surface rust from sitting the last 6 months on jack stands.

Need to swap out the alt/ac adjustment pulley as it squeaks bad. Ed sent me the wrong one so waiting on him to send the right one...LOL

I'm getting some smoking when I downshift and let it rev out. Doesn't do it al the time, just randomly. Wondering if the PCV valve is not working right so I'll be swapping that out. Possible due to rings not broken in all the way yet.

I also get a random backfire which makes no sense as timing is 100% on. I have checked it so many damn times now it is not even funny.

Finish getting the interior back in and wiring in the Wideband. I swapped over to an Innovate as it is easier to log since MMCD and Scanmaster are coded to use it.


With winter coming in and it being completely dark out by the time I get home I only have the weekends to work on it. I'm in no rush though as everything else is at this point is pretty minor.

DrGonzo
08-22-2014, 05:29 PM
Just wanted to throw in some long overdue updates to the engine and car.

Power steering issue was just a loose belt.- All fixed!
Brakes are perfect now and lock up if you mash them - No ABS
Alt/AC pulley issue fixed
Smoking went away after the first 1k miles on the engine.
The engine developed really really bad compressor surge. I couldn't drive it on the highway at 65 as the BOV sounded like a train coming at you... Converted back to stock SMIC's and that fixed the surging issue and the backfiring problem...IDK why on the backfiring issue...

I have taken the car out atleast once on the weekend to local meets and such, even 3 hrs to the Ninja garage for a meet with no issues at all.

noticed a small oil leak I traced back to the rear valve cover. Pulled the cover and resealed it. Engine runs like shit and then starts dying. You start it up, runs good, then the MFI kicks off killing the fuel. Checked and checked and couldn't figure it out. Finally sent my ECU to the Ninja and it's toast. It was rebuilt by Eric Rymer 2+ years ago when he first started doing them. Chris's ECU is fixing it and I'm waiting to hear a root cause.

So while the ECU was out I figured might as well change out the bad A/C compressor I had with my spare I got last year. Compressor went out fall of last year so I didn't mess with it as I didn't need it. All installed and having issues with it keeping a vacuum overnight. Going to swap out all o-rings to see it that does it. then run dye to see if I can locate the issue. I usually run a small can of A/C stop leak in the system just as a precaution but with no running engine I can't get it into the system...LOL I have a large o-ring kit with tons of o-rings so I'll change them all out first.

Seeing as the engine now has 3k on it, might as well do the oil also. Drained the pan and got the normal metallic sheen due to engine break-in. Pull the oil filter and dump in toward the outer rim and chunks fall out... WTFF!!!

https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-xfp1/t31.0-8/p600x600/10528372_10153025093304186_8361179101296137695_o.j pg

So needless to say I was really freaked out. it was late when I drained the oil so I had to wait until the next day after work to actually inspect anything.

After work the next day I immediately started looking into the oil issues. I pulled a few chunks of the oil and most looked to have been carbon buildup chunks. The next one seemed to be bits of white/yellowish plastic. No metal chunks found at all. I was relieved but concerned also as to where the plastic chunks came from. So I took the oil in the closed off oil container. Since the filter oil did not get inside the oil container, just the outside, I knew if I filtered it I could tell if the chunks where in the oil pan on the car also or just on the filter. Ran the oil though some really fine paint strainers/filters I had and nothing. Not a single bit came out. I even backwashed and swished the oil container to get anything on the bottom of it out. They filled it with water and strained/filtered that also. All clean, no chunks. So I know now that the chunks were in the filter itself. There were maybe 7-8 chunks of the plastic found and I'm guessing they are glue from inside the filter itself caught in the filter creases. I used a Wix filter as I have used them for a couple years now with no issues at all.

I also sent an oil sample out that I took from the oil pan on the car was draining to Blackstone labs. Got a call from them today. They saw my note about the chunks but found nothing in the oil. chromium was a little higher than they like to see at 15ppm, but this is the first 3k oil change on the new engine and with new rings, minus the initial two done right after the engine was turned over and the one after I brought it up to temp. Everything else on the report looked great they said. I know that I didn't change or flush the oil cooler from the old engine, it didn't spin a bearing or anything and those reports had high chromium levels so that chromium could also be from the oil that was sitting in the cooler from the old engine which had 80-90k on it. Compression and everything is good so I'll just keep an eye on it after the next report. if the chromium doesn't go down then I'll need to look into trying to find the cause of it.

CoopKill
08-22-2014, 07:18 PM
Wheeeeeeew! I looked at the pic, and was OMG!!!! After everything I am going through it is good to see something good going someones way.

lawdogg
08-22-2014, 08:09 PM
Wow so that was the Wix filter? Shitttay

DrGonzo
08-22-2014, 09:51 PM
yeah, I was pretty bummed about finding that stuff in the filter. I've been a big Wix person for quite some time now. Technically it did do it's job though as Blackstone found not evidence of foreign materials.

I got the full Blackstone report emailed to me and I'm not the happiest about the figures....I know the first oil change or two is going to be bad but I never though that they would be this bad!!!

http://3s.gonzoinc.com/albums/userpics/10002/Blackstone.PNG

the numbers just seem to be really high for the metals. I know Iron, aluminum and chromium would be high, but the copper, lead and tin!! That's bearing metal!!! So my debate now is pull the pan and look over all of the bearings, or run it for 1-2k and send in a new sample and hope for better numbers. Oil pressure is absolutely wonderful. I've never had oil pressure this consistent. Almost 24psi at warm idle 45-50psi highway cruising. I didn't built the engine in a clean room or anything and this was the first oil change with the engine under any type of load at all..... Am I just worrying to much about this??

CoopKill
08-22-2014, 10:30 PM
What was Blackstones thoughts on it? Did they give an opinion?

lawdogg
08-22-2014, 10:38 PM
Looks like you changed the oil type too?

DrGonzo
08-22-2014, 10:42 PM
They called me when they got the results from the engineer. They were worried about the lead and asked if I ran race fuel. I did run about 10 gallons of leaded 110 at the drag strip last year and have not changed the fuel filter since then. They asked if I had any oil pressure issues either, which I do not. they only found a trace amount of fuel in the oil which is good as that means fuel is not getting past the rings. they were also concerned with the Chromium as that is from piston rings. They stated it is high even for a new engine build, but seeing as that was the first oil change with any load on the engine I would expect it to be high as the piston rings are seating from the compression strokes under load and the vacuum from downshifting. So they recommended running it for 2k and sending in a new sample since I told them the engine runs fine. Now right before I took the sample is when I was trying to figure out the ECU issues, so for about a week or so I had been in the garage cranking the car, it would run for a min or two and die while I was checking things out trying to track down the problem that ended up being the ECU. Wonder if any of that flawed the sample at all...

CoopKill
08-22-2014, 10:53 PM
The constant cranking could add to the chromium.

DrGonzo
08-22-2014, 11:06 PM
yeah, I'm really steering toward this just being a bunk sample due to everything going on prior to me taking it. I'm waiting on the ECU to come back from Chris so I can;t drive the car now anyway.... I'm just stuck where I can run the 1-2k and the next report will be fin, or I stand the chance of screwing the new engine. Or I pull the pan and find the bearings are screwed or their fine and I did all that work for nothing....Blah!!

CoopKill
08-23-2014, 12:05 AM
Or I pull the pan and find the bearings are screwed or their fine and I did all that work for nothing....Blah!!

This all too well hits home...

Chris@Rvengeperformance
08-23-2014, 03:06 PM
yeah, I was pretty bummed about finding that stuff in the filter. I've been a big Wix person for quite some time now. Technically it did do it's job though as Blackstone found not evidence of foreign materials.

I got the full Blackstone report emailed to me and I'm not the happiest about the figures....I know the first oil change or two is going to be bad but I never though that they would be this bad!!!

http://3s.gonzoinc.com/albums/userpics/10002/Blackstone.PNG

the numbers just seem to be really high for the metals. I know Iron, aluminum and chromium would be high, but the copper, lead and tin!! That's bearing metal!!! So my debate now is pull the pan and look over all of the bearings, or run it for 1-2k and send in a new sample and hope for better numbers. Oil pressure is absolutely wonderful. I've never had oil pressure this consistent. Almost 24psi at warm idle 45-50psi highway cruising. I didn't built the engine in a clean room or anything and this was the first oil change with the engine under any type of load at all..... Am I just worrying to much about this??

That's 3 times the lead I had in the oil sample I sent in that came from my spun bearing engine. I'd check the bearings.

DrGonzo
08-23-2014, 05:32 PM
That's 3 times the lead I had in the oil sample I sent in that came from my spun bearing engine. I'd check the bearings.

Was that the first oil change sample sent in after building the engine where your lead numbers where high?

Chris@Rvengeperformance
08-23-2014, 09:34 PM
Was that the first oil change sample sent in after building the engine where your lead numbers where high?

no, I sent the oil change from the oil that was in my old engine when it spun the bearing and it read 40 lead.

The new motor test showed 6 for the lead after 400 miles.

DrGonzo
08-23-2014, 10:21 PM
I've been thinking about it today and I'll be pulling the pan to check things out. I should be able to get it pulled tomorrow and atleast check the rod bearing. I'll post up my findings. Wish me luck!!

wingnut
08-23-2014, 11:18 PM
I'll post up my findings. Wish me luck!!

Lotsa luck!

http://i.imgur.com/f0nlv7a.jpg



















Oh, wait...:welcoming:

DrGonzo
08-24-2014, 02:36 PM
Ok, so here are rod #1 & 2 bearings

#1
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1592.JPG

#2
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1591.JPG


The image is not the best, was having issues trying to get the light right. That is not copper showing on the bearing. Just the bearing polished. No copper showing at all on either, no grooves and they are all very smooth. Slight black on the top of both bearings. I did use a crap oil for the first start-up which may not have been the best and the engine did sit for 6 months after I got the rotating assembly done so the lucas assembly oil may have run out of the top of the bearings in that time which caused the heat at the top on initial start-up. I may also want to look into a slightly heavier oil as it may have been the 10W-30 I was running was too thin. Viscosity on the report was lower than normal which would contribute to the heat at the top of the bearings as these show. I can almost rub it off with my thumb. Crank looks great! I found a few small slivers in the pan of aluminum which I think are from the the rockers that fell of and hit the cam shaft. Camshaft was still good but did have a slight groove. not enough to mess with the cam timing tough. i never even thought about draining the oil when that happened....Duh!!!

I'm going to drop these two bearing back in as I see nothing wrong with them and then check the rest as I am sure they are all going to look the same.

DrGonzo
08-24-2014, 03:53 PM
Here is rod bearing #3-4

#3
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1593.JPG

#4
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1594.JPG


Again all are smooth, no groves, no copper. Slight blackening on the top bearing. Most of the blackening wiped off with a towel. The lines you see on the bearing are just the difference between the mirror polished part of the bearing and the stock dull gray that the bearings come.

Wondering if the Clevite bearings are just not 100% smooth out of the box hence the lines that develop during wear. No lines whatsoever on the crank itself. it is a perfect mirror polish. At this point I have zero worries that this engine was susceptible to spinning a bearing. I'm almost 100% convinced that the higher metal numbers are due to the over-sized Clevite bearings wearing in on the turned crank.

Re-installing these bearings and pulling the last ones. Then maybe the cradle to check the mains.

DrGonzo
08-24-2014, 04:52 PM
Here are bearings #5-6

#5
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1595.JPG

#6
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1596.JPG

So all of the rod bearings are fine. no major issues for me to worry about that I'm aware of :p

I won't have time to pull the cradle today to check the mains so I'll have to check it some other time. I see no reason the mains would have issues.

wingnut
08-24-2014, 07:16 PM
I won't have time to pull the cradle today to check the mains so I'll have to check it some other time. I see no reason the mains would have issues.

Maybe not, but the mains are the ones that caused my issue...rods were fine!

DrGonzo
08-24-2014, 09:46 PM
Really, I've only heard about about rod bearing spinning. I don't think I've ever heard of the main spinning, usually the rods go first as they take the worst beating.

TurboSinceBirth
08-24-2014, 10:24 PM
Rods will spin if you have an oil starvation issue. The mains will spin from a bad tune which can included too much knock or timing advanced too far. It will hammer out the centers. That's what I've found. I never had a rod bearing spun. It was always the mains wearing down to copper or spinning.

For future reference this is an excellent place to look when you want to know what's going on with your bearings. They tell the story of what's going on with the engine.
MAHLE Clevite - Bearing Analysis - BETA v3 (http://catalog.mahleclevite.com/bearing/)

DrGonzo
08-24-2014, 11:47 PM
Yeah, no tune on this motor as of yet. Ran it 100% stock and really no hard boost on it. Boost controller set to 12 psi. Did a couple pulls checking boost and such but the engine was not abused at all.

I checked a couple bearing analysis sites and none really showed the blackening like I had. Most that had any blackening also had grooves and lots of copper showing. Most of the blackening I had wiped right off with a paper towel so it's on the surface not embedded into the bearing material. Seeing as I did a lot of engine cranking when the ECU when out trying to figure things out, that also may have contributed to the black spots. I'm really attributing the black spots around the bearing oil hole to viscosity issues with the Valvoline oil I was using and the cranking that was done when I was trying to figure out the ECU issue. The crank looks perfect so there was no starvation of contact with the bearings. So far everything looks great. As soon as I get time to drop the cradle I'll know more as to if I have any main bearing issues but as of now I don't see that I'll have any issues.

donniekak
08-25-2014, 03:01 AM
Those bearings show a couple problems. Uneven wear, and some contact with the crank on the upper shell. Either the crank journal is tapered, or the rod is twisted, or resized improperly.

In these engines, the rods wear and spin mostly from oil starvation. That starvation is caused in part by the mains wearing, and loosing pressure to feed the rods. By the looks of those bearings, I'm willing to bet the mains have some wear.

It takes a few minutes to pull the girdle, I'd take a look if I were you.

DrGonzo
08-25-2014, 07:48 AM
Those bearings show a couple problems. Uneven wear, and some contact with the crank on the upper shell. Either the crank journal is tapered, or the rod is twisted, or resized improperly.

In these engines, the rods wear and spin mostly from oil starvation. That starvation is caused in part by the mains wearing, and loosing pressure to feed the rods. By the looks of those bearings, I'm willing to bet the mains have some wear.

It takes a few minutes to pull the girdle, I'd take a look if I were you.

There is no uneven wear on the bearings beyond the difference in the portion of the bearing that is polished and what is not polished. that difference is microscopic and seeing that the bearings only have 3k miles on them I wouldn't expect a full bearing surface polish since it is the oil that does the bearing polish not the crank.

Those are also not contact marks from the crank. It's a film where the oil got hot due to it being thin or a low viscosity. either it was caused cause the oil was too thin or from all the cranking I was doing working on the ECU issues over a couple weeks. the black film wipes right off. crank contact would have shown a bluish mark that won't wipe off.

Rods are stock and where not reworked in any way. they where checked for roundness and bore which were fine. Crank was turned and spec'd also which was .010 on the rods and .020 on the mains.

I will be pulling the crank girdle to check the mains. I may be able to do it in the next couple days depending on work.

DrGonzo
08-26-2014, 02:39 PM
So... I got the cradle dropped at lunch. couple spots on the mains where crap was in the oil but I can barely hit is with my fingernail. Crank looks perfect, nice mirror shine so no crank damage.

Thrust bearings on the other hand.... yeah... So this is my first complete build and the one thing I did not do when I did the mains, thrust bearings, etc... was make sure the damn cradle was on straight and the thrust bearings where flush to one another on the seam. The cradle is very tight getting it in/out so I made the stupid assumption it lined up when I installed it.

So the oil analysis is right as the thrust bearings are really worn down, one of each side from the cradle not being installed straight. Luckily I see no damage to the crank so I should be able to drop a new set in and be good. The thrust bearings wore evenly on those two sides down to the copper. No indication of crank contact on either the crank of the thrust bearing. Looks like is was just off enough to cause excess wear on those two.

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1602.JPG

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1601.JPG

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1600.JPG

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1599.JPG

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1598.JPG

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1597.JPG

I couldn't get the #1 top main bearing out and didn't want to force it. Seeing as the top mains "the ones sitting next to each cradle bearing" looked good I wasn't too concerned with a visual inspection on it.

Seeing as there is nothing catastrophic with the mains I wonder if I can just drop them back in..... Opinions? I can't catch the grooves on the bearings with my nail which i was told in the past is a big factor in needing to replace them or not. IDK, not like they are expensive or anything, but why drop the cash if I don't have to. New thrust washers will be on order though.

Jimvr4
08-26-2014, 04:04 PM
Greg, is this a four bolt? I didn't think it possible to misalign the cradle. How are you ensuring it is aligned?

CoopKill
08-26-2014, 04:17 PM
Well the good news is you found it, and the other good news is you found it!

What is the story on this bearing?

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1598.JPG

As far as throwing them back in, imo it would be a $50 peice of mind, but they don't look all that bad. Sooooo... Your call! :p

DrGonzo
08-26-2014, 04:25 PM
Bad photo....lol It has some blackening like the rod bearings do but no damage at all. I can't get good photos with my iphone camera. I need a camera with a good macro lens. the light from my workbench doesn't seem to help either.

The blackening I'm going to associate to a viscosity issue with the Valvoline oil i was running getting hot. That is the first main bearing to get oil so it's not a flow issue as #4 should show issues if it was a flow issue as it is the furthest from the oil pump. The blackening for the most part wipes right off.

donniekak
08-26-2014, 04:38 PM
I don't know what your seeing, but I've pulled bearings out of 20year old 100,000+ mile engine that look better than that. Carry on.

CoopKill
08-26-2014, 04:53 PM
I don't know what your seeing, but I've pulled bearings out of 20year old 100,000+ mile engine that look better than that. Carry on.

If you could elaborate on what you are talking about it would be great.
Other than a couple of slight debris scratches all I see is the surface lube coating wearing off.
Here to learn teach meh please...

Jimvr4
08-26-2014, 04:58 PM
It looks like you didn't set the thrust. Thread from the other site:

Setting Crankshaft Thrust Bearings - 3000GT/Stealth International Message Center (http://www.3si.org/forum/f35/setting-crankshaft-thrust-bearings-626193/)

DrGonzo
08-26-2014, 05:05 PM
I don't know what your seeing, but I've pulled bearings out of 20year old 100,000+ mile engine that look better than that. Carry on.

Care to explain that statement?

The bearings are smooth minus the #4 and #3 bearing having a line from something in the oil. Likely at start-up since the block was machined and the crank was turned. The lines are not deep enough to catch my fingernail. The Clevite 77 bearing come a dull gray finish, so the other lines you see are the difference after 3k miles of the original dull finish and the the oil/film layer polishing the other area of the bearings.

On the #2 bearing, what looks like a colored burned spot in the middle is a mixture of camera flash, the dull/smooth lines of the bearing and a slight blackening which was the same found on the rod bearings. which wipes right off with a paper towel. Oil viscosity on the oil report was low so it would cause the blackening seen as the flash-point was low also which means the oil will burn in when it comes in contact with heated parts.



Greg, is this a four bolt? I didn't think it possible to misalign the cradle. How are you ensuring it is aligned?

This is a 2 bolt TT block. Max I'll ever shot for is 450 hp so no need to track down a 4 bolt block. the crank is forged and was turned. mains are .25 over-sized and rods are .50 over-sized.

Doing a quick reading after seeing the thrust bearing resulted in a thread Ray commented on about ensuring that the thrust bearing ends where flush when the cradle was installed as it can mis-align slightly. Tapping it into place to ensure the thrust bearing ends are flush with one another. There are no alignment dowels on the cradle so when it is installed in can shift one way or another which is what happened here. I had a lower block side and upper cradle side thrust bearing showing copper so the cradle was not aligned when I installed it.

Again the crank looks fine so it looks like is was just off enough to have to close of a clearance. Also running the Spec stage 2 clutch will put that outward force on the thrust bearing, mixed with them being mis-align caused the premature wear. Copper was 20 over normal range, nowhere near the lead "@ 153" so it looks like it just started to get to the copper portion of the thrust bearing. The lead is soft enough to not damage the forged crank, pretty sure the copper is soft enough also to not cause any damage. So it is a good thing I checked all the bearings as I never even though about the thrust bearings, go figure. Even better is that it is very easy fix and my engine is not toast!!! Just going to be a pain in my ass lining things back up with the engine still in the car. Much easier to do when it's on a stand. Since I know what I did wrong now I know what all I need to keep an eye out for.

I'll go ahead and get new main and thrust bearings from Chris, probably order them this weekend. That will give me all week to get the pan and such cleaned up to get it all back together. Hope to have my ECU back from Chris then also.

DrGonzo
08-26-2014, 05:09 PM
It looks like you didn't set the thrust. Thread from the other site:

Setting Crankshaft Thrust Bearings - 3000GT/Stealth International Message Center (http://www.3si.org/forum/f35/setting-crankshaft-thrust-bearings-626193/)

yeah, I remember reading that when I built the engine. I think I pulled the cradle off again after I initially set it and forgot to check it over again hence why it was out of alignment. I was working in a 4x4" shed at the time I built the engine and it was winter time.... I'll blame it on brain freeze...LOL

CoopKill
08-26-2014, 05:12 PM
Will be inspecting my thrust this weekend as well to see that they were installed properly. lol I want nothing to do with getting all that crap installed from my back. She comes out soon.

donniekak
08-26-2014, 06:52 PM
An oil film polishes nothing, only metal to metal contact. The fact that one side of the bearing has wear of any kind, and the other doesn't, points to a tapered journal, twisted rod, or tapered rod bore. I pull bearings out of engines making 150hp per cylinder that look brand new.

With the thrust being that worn you also need to check the thrust face if the crank. If it isn't mirror smooth you need another crank, and there is no thrust repair on these cranks, unless you get it welded.

DrGonzo
08-26-2014, 09:42 PM
An oil film polishes nothing, only metal to metal contact. The fact that one side of the bearing has wear of any kind, and the other doesn't, points to a tapered journal, twisted rod, or tapered rod bore. I pull bearings out of engines making 150hp per cylinder that look brand new.

With the thrust being that worn you also need to check the thrust face if the crank. If it isn't mirror smooth you need another crank, and there is no thrust repair on these cranks, unless you get it welded.

Umm, No! Oil does not prevent friction it just tries to reduce it and heat. Friction causes the polish. More friction in less clearance areas based on the viscosity of the substance.. Anything moving across another surface causes friction regardless of it being a solid or liquid. There is no such thing at this time as friction-less anything. Friction of the oil and whatever is suspended in the oil will cause the bearing to polish over time. Add that to the pressure and volume the oil pump is pushing out and you have something that will polish any surface it come in contact with. Just like a river polishing stones.

As for your 150hp statement. I don't believe it. Below is the bearing from my engine with 3k on it, right next to the bearing that came out of my old block. that block had about 140k on it since it was rebuilt and about 250k on it total. That was a 10:1 block that was boosted for about 70% of it's life. Turned crank using King .25 over-sized bearings and a cast crank. Now as you can see that bearing has the same upper dull gray marking which is how it shipped from King and the lower portion is polished as that is whee most of the oil flow goes. So even after 140k it still shows the same pattern on the bearing with the left side being grey and the right side being polished. The left side just has mush less mileage but over time they would look almost identical to the point they would stop wearing as fast as once you open the clearance up enough you less restriction and heat so flow will resume causing less wear.

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1603.JPG

Here are the rest of the bearings still in the girdle from the 10:1 boosted engine. Today was the first time I pulled that pan since that engine was rebuilt 15+ years ago! That engine went through absolute hell! Multiplier times at the track, the dragon, cross country trips, multiple head gaskets, 16 PSI boost, ETC!! If the timing belt hadn't gotten a hole in it from be dropping a nut into the timing area it would still be in the car. I have no doubts about slapping it and the bearing back in and running that engine for 100k more with nothing but a new oil pump!!

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1605.JPG
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1604.JPG

Seeing this was the first oil change on a brand new engine, I expected there to be a high level of particles in the oil as I didn't built this engine in a clean room. I also had a lot of machining and cleaning done to all parts as the crank was turned, the block was honed, Etc. The crank had the oil galley balls drilled out and taped for set screws so I could ensure that after it was turned I could clean out all of the passages. The block itself came from a spun bearing motor. It was hot-tanked twice. The heads where machined, valves done, etc. So all that means more particles in the oil and more particles in the oil to wear things down as it is impossible to get them all 100% clean. You will still have shit come free.

Case being that the bearings I pulled out are fine and are wearing as they should be considering the conditions the engine was built in. I am a very meticulous about cleanliness and even I know that it would have been impossible to keep everything 100% clean. The black marks on the bearing show me that Valvoline should not be run in the engine as it does not have the viscosity needed and gets too hot.

The only reason I am going to do the mains on the new engine again is that they are cheap and the #2 main on closer inspection does have a little copper showing from debris in the center scratch. Seeing as the scratch does not go from oil hole to oil hole my guess is the debris was a piece of the plastic from "What we presume" the oil filter, got into the oil. It started to scratch the bearing but the plastic is so brittle it crushed hence the fade out of the scratch and no damage to the crank. Metal debris would have scratched the entire surface of the bearing and most likely the crank also.

As for the thrust bearings, the crank side is fine and still a mirror polish which I expected it to be. The bearing material is not dense enough to damage the forged crank unless it completely fails and wedges/spins like when bearings fail. The thrust bearing babbet material just wore off those two thrust bearings. I'm going to slap in the new ones, and check the clearances which should be spot on. I already talked to Chris and the bearings are on his shelf already. So order them Friday/Saturday and have them on Monday.

donniekak
08-26-2014, 10:11 PM
Well then, I'll leave this to the experts.

DrGonzo
09-04-2014, 11:36 AM
So I get the new main and thrust bearings yesterday thanks to Chris at Ninja Performance!!

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1627.JPG


Since everything was still apart it was pretty simple install. Cleaned off all the oil from the crank/girdle area, installed the new mains and checked clearances.

Main #1 - 0.020
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1628.JPG

Main #2 - 0.020
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1629.JPG

Main #3 - Between 0.015 and 0.020 Little tighter than the rest but still within spec
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1630.JPG

Main #4 - 0.020
http://3s.gonzoinc.com/albums/userpics/10002/IMG_1631.JPG

Pulled the girdle and mains, lubed them up, installed the thrust bearings and re-installed the girdle. Torqued it down to spec and then broke the main bolts free. Centered the thrust bearings by tapping the crank on both sides to center them out. Pulled out the dial gauge and checked the thrust movement at 4 different spots on the crank. 0-90-180-270 degrees all came in at .003" +/- .0005". Re-torques the main caps and added then bolted in the girdle stays and torqued them down. So everything is spot on where it is supposed to be.

I started cleaning the oil pan up last night and it was drying overnight. Need a light coat of paint as the wire brush I used took the paint off. I'll get a coat applied at lunch today since I'm working from home today....:p That should give it time to dry and I should have things buttoned up after work. The when My ECU gets here I can fire things back up!!

lawdogg
09-04-2014, 11:55 AM
You're a machine!

DrGonzo
09-04-2014, 12:37 PM
You're a machine!

LOL, the things I can get done now that I have a garage! LMAO!!

Toni
09-04-2014, 01:20 PM
Nice! Gonna feel nice once it's all buttoned up.

DrGonzo
09-08-2014, 12:10 AM
Almost 100% back together. Couple more things to button up, add fluids and the Stealth should be back running.

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1636.JPG

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1637.JPG

http://3s.gonzoinc.com/albums/userpics/10002/IMG_1638.JPG

DrGonzo
09-13-2014, 02:59 PM
Spent most of the last couple days trying to get the car to start after getting the new bearings and ecu in the car, Had no injector pulse or spark. Found the CAS signal wire came loose from the ECU harness so I fixed that and had fuel, still no spark. Pulled the PTU and coil, checked them and all wiring. All good. Put it back together and it fires up..... WTF!!!

Now I have a loud tick coming from the rear bank which I'm assuming is another rocker fell off again due to the car sitting so long in the garage.... SO I have to pull the top rear apart to get that fixed once everything cools down. Pain in my ass this car is!!!!

DrGonzo
09-14-2014, 04:13 PM
I found a couple lash adjusters that were sloppy so I pulled and cleaned them out. Got the engine all back together and fired it up again. Purrs like a kitten. I let it run for a bit to get up to temp and then adjusted the idle. Video is of before adjusting the idle. Still have minor lifter tick that seems to be getting better. Seeing how the engine has sat with no oil circulation for the last month or so I can expect to have some tick in the lifters. I let it all run for about 10-15 checking for leaks and all looks good so far. I did notice TPS signal wire at the ECU is acting up again which I'll need to look into. I got the engine cooling down now to check fro leaks again and top off fluids. Then it will be time for road test!!


http://www.youtube.com/watch?v=RqeDBRx-Wrs&feature=youtu.be

DrGonzo
09-14-2014, 10:23 PM
Road test completed! I put about 20 miles on the car on the back roads and highways. Running better than ever. In serious need of an alignment which I'll set up for next weekend "Lifetime Alignment at Firestone FTW!!".

Found out one of my front ECS struts has a bad wire inside the strut so my ECS is dead right now. So the ride was a little floaty at times. I know the one front one is stuck in medium mode and it looks to be the ground wire to the motor inside the strut is what went out. My ECS tester lights work so it's not a micro switch that went out. So I'll manually set the others to medium mode sometime this week while I track down a new front strut.

car is in serious need of a bath and detail which will be #1 on my list first chance I get.

I also found out that Tirerack has my Dunlop Direzza DZ101 tires on closeout special for $68.00 each so I picked up a set of 4 to keep them around. Two will go on as my fronts are way worn over what they should be. Rears have the DZ101 already on them from a couple years ago and still look brand new!

Elderloc
09-15-2014, 12:41 AM
This warms my heart, glad to see it's back on the road.

When you say life time alignments at Firestone can they do a four wheel? I still have my rear steering and I've been trying to think where I should take it since the local Mits dealer is a little flaky.

DrGonzo
09-15-2014, 07:33 AM
Yeah, They do a 4-wheel alignment on their laser rack. My wife got me the alignment package for Christmas a few years back. It runs about $180 or so, but I usually get about 5-6 alignments per year so it has more than paid for itself.

Elderloc
09-15-2014, 09:54 AM
This is very good news, having completely redone front and soon the rear I'm going to need it. Now to figure out who can do the bleeding on the rear PS. I really don't want to run the car at 35 mph on my lift.

Thank you for the info, I agree that package will easily pay for it's self.

DrGonzo
09-22-2014, 03:14 PM
So I went in on Sunday to get the alignment done and they couldn't do it. Front end had too much front/rear play to be able to get everything set.

Firestone guys and myself checked things out while it as still on the rack and found the inner tie rod joints were bad, Passenger side was really loose. Almost 3/4" play on that side. So I finally figured out why the damn steering was so wonky on the car. I always thought it was just because it had an N/A rack on it so it wasn't as tight as the AWD rack.

I got new inner tie rods on order and will slap them on when they get here. New Dunlop Direzza DZ 101's will be here today so I'll get them installed the same time the alignment gets knocked out, probably next weekend.

Jimvr4
09-22-2014, 08:20 PM
Nice :) Always good to find out the root cause and your car will be so much better after fixing that. I used Firestone last time BTW and they were able to setup just enough negative camber so I could avoid rolling my rear fenders.

lawdogg
09-23-2014, 12:21 AM
Nice dude! You probably don't need it but this might help: http://www.3sgto.org/3000gt-stealth-gto-related-topics/3911-what-did-you-do-today-your-3-s-161.html#post288880


Out:

https://lh6.googleusercontent.com/-4vZDblnkCU4/U7BdbuI_jwI/AAAAAAAAFa8/GaLnQgVbcJk/s800/IMG_20140629_113501632_HDR.jpg

In:

https://lh6.googleusercontent.com/-6v4gdasMKDA/U7BfttHnr-I/AAAAAAAAFbI/wa2Ick1CKCM/s800/IMG_20140627_195627459.jpg

Ball Joints: Moog K9855
Outer Tie Rods: Moog ES3044RL
Inner Tie Rods: Moog EV800540
Boots: QuickSteer K9358

Some issues with INNER Moog tie rods: (1) inners have a smaller flat section to get the tie rod puller on, which doesn't let the tool on if the plate is bent in place already, so you have to bend it once on, (2) it's impossible to bend one side of the small anti-rotation back plate over the inners since it's tucked up above;

OUTER Moog tie rods: cotter pin location is 1/8 to 1/4" too high to use their castle nuts so you have to re-use the stock ones;

Moog ball joints: the damn C-clips don't have me too confident that they're firmly clipped since they bend when you install them. Cross your fingers. :culpability:

Finally, the boots are too small but will stretch over if you roll them on like a condom (OE on right).

https://lh6.googleusercontent.com/-EIQ-JSE1qzU/U7BumhSDqMI/AAAAAAAAFbY/FQbBo-RwoEE/s800/IMG_20140627_224242365.jpg