WANTED: Some nuts and bolts

[99ishVR-4]

I am in need of a few fasteners before I take all mine to get re-plated. I am in need of the following:

Driveshaft to rear-end:
I need all 4 bolts, 4 nuts, and 4 lockwashers
http://i.imgur.com/iZpKJTY.jpg

Driveshaft front section to midsection
4 bolts, 4 nuts, 4 lockwashers (these are all identical to above ones so I technically need 8 of each).

Carrier bearing to car
I need the 4 washers and 4 nuts


4 front caliper bolts & lock washers (TT brakes, m12x43)
http://www.3sx.com/store/catalog/stock-caliper-bolts-01-400l.jpg
http://www.3sx.com/store/catalog/stock-caliper-bolts-06-400l.jpg

One of these clips from the interior door sill panel:
http://i.imgur.com/EEt0dVg.jpg

One screw from a junk cargo cover end piece:
http://i.imgur.com/zYUqZ1Z.jpg

One front turbo-to-o2 housing stud
One front turbo-to-o2 housing nut
http://i.imgur.com/HmtCdwC.jpg

One front turbo-to-exhaust manifold bolt
http://i.imgur.com/OIQ3Fya.jpg

[Street_Chally73]

Worst-case scenario, I am 99% sure you can source most of these new through Cherry Hill Mitsubishi. I might even have my original ones for the Lobro joint & propeller shaft flanges (the nuts for the carrier bearings were toast)...I'll check when I get home later today & get back to you.


Sent from the garage

[99ishVR-4]

Worst-case scenario, I am 99% sure you can source most of these new through Cherry Hill Mitsubishi. I might even have my original ones for the Lobro joint & propeller shaft flanges (the nuts for the carrier bearings were toast)...I'll check when I get home later today & get back to you.


Sent from the garage

Yeah I found them all on their site, but the driveshaft bolts seem to be a little rediculously overpriced, lol. I think it comes to $40 just for the 2 driveshaft sections. They are my next resort if I can't find anything on here.
I am interested if you have some in good shape. Thanks

[Bloodlust182]

I should have the sideskirt bolts.

[green-lantern]

I might have some of those. I have Jackhammers old box of bolts. You might know already that my car is an AWD conversion, I made my own carrier bearing mounts out of stuff I already had and bought bolts from the hardware store for the DS. That was before I got all these bolts. If you know the length and grade I'd say I have them.

[99ishVR-4]

I should have the sideskirt bolts.

As long as they are in good shape, how much do you want for 4 of them?

[99ishVR-4]

Yeah I remember, I'll try to find the specs on the bolts.

[Bloodlust182]

Uhh a dollar plus shipping sound good? Ive got a 50 pound bucket of fasteners from parting out 2 3/s 's that ill dig through to find the best ones. I may have the other stuff you are looking for in that bucket too lol. The bolts on the DS are 10 grade im pretty sure from the numbers on the heads.

[akotten]

Uhh a dollar plus shipping sound good? Ive got a 50 pound bucket of fasteners from parting out 2 3/s 's that ill dig through to find the best ones. I may have the other stuff you are looking for in that bucket too lol. The bolts on the DS are 10 grade im pretty sure from the numbers on the heads.

Woah. Do you happen to have any front suspension fasteners?

(sorry for the hijack, OP)

[Bloodlust182]

Woah. Do you happen to have any front suspension fasteners?

(sorry for the hijack, OP)

I should, what are you looking for?

[akotten]

I should, what are you looking for?

On the lower a-arm, there is a large bolt that goes between two smaller ones. It fastens the rearward bushing on the a-arm to the subframe. I'll see if I can snag a picture later.

[Bloodlust182]

On the lower a-arm, there is a large bolt that goes between two smaller ones. It fastens the rearward bushing on the a-arm to the subframe. I'll see if I can snag a picture later.

http://i289.photobucket.com/albums/ll203/bloodlust182/rjc-standfront_zps479fc692.jpg (http://s289.photobucket.com/user/bloodlust182/media/rjc-standfront_zps479fc692.jpg.html)
These? Sorry for the thread stealing 99ishVR-4

[akotten]

Yup! haha, good work.

[Street_Chally73]

I just checked to see what I had & apparently I reused them (just the flange was sitting there). It sounds like you have two others with plenty of bolts, so hopefully you can get what you need from them...Sorry about that; I could have sworn I bought all new fasteners back when I redid the propeller shaft, but I guess I just got new carrier bearing nuts only.


Sent from the garage

[green-lantern]

I'm glad I normally keep my mouth shut

[99ishVR-4]

Lol, sounds good.. Shipped to 33844.

[Bloodlust182]

Ok I found the side skirt bolts, i wasn't able to find the caliper spacer but its w/e. Ill ship them out Tuesday from work(I work in a shipping department) in a padded envelope, should only be like 2 or 3 dollars for shipping.

[99ishVR-4]

Ok I found the side skirt bolts, i wasn't able to find the caliper spacer but its w/e. Ill ship them out Tuesday from work(I work in a shipping department) in a padded envelope, should only be like 2 or 3 dollars for shipping.

OK so $4? what is your paypal?

[Bloodlust182]

bloodlust182@gmail.com

[99ishVR-4]

Buumping this thread so I can finally go to the platers. I updated the first post with everything I still need.

[99ishVR-4]

Buuump

[99ishVR-4]

List updated. Need 45 pieces total.

[99ishVR-4]

buuump

[99ishVR-4]

buuuump, still need every fastener I mentioned above.

[Bloodlust182]

I have the 8 driveshaft bolt, nuts, and washers

[99ishVR-4]

I have the 8 driveshaft bolt, nuts, and washers


Ill take them, how much and whats your paypal? Thanks

[Bloodlust182]

bloodlust182@gmail.com What do they usually go for? I know 10 Grade bolts are pricey. 14 shipped sound good?

[Streamln1]

I may have some of what you are looking for.

I actually sourced a whole bunch of flange type metric bolts on amazon and ebay in the yellow zinc coating, all in all I probably could have spent less on just having all the OEM bolts plated like you are doing. For the larger bolts OEM is significantly cheaper than other sources, I would say the opposite is true once you get below an M10, Although I did source some 10.9 grade M10 flange bolts for under $10 for a box of 5 from Dorman. For M6 and M8 flange bolts I paid less than 10 shipped for 25.