PDA

View Full Version : Low Oil Pressure



Memphetic
05-05-2013, 12:32 PM
What do you suppose would cause low oil pressure? I drained the oil and filtered it as it was coming out with a 190 micron filter - no copper.

The magnetic drain plug had a small amount of ferrous (silver in color) metal on it, which is typical of a freshly built engine.

Oil pump is (obviously) brand new. I've changed the oil about four times in the last week because I'm deathly afraid of spun bearings :-P

Oil pressure is being determined by the stock oil pressure gauge/sender - but it's only registering one tick mark at idle and about halfway up to the "where it should be" marks during cruise.

Any guesses?

ICPREY
05-05-2013, 12:47 PM
Install a real oil pressure gauge (even if it's temporary) and go from there. Did the engine shop use OEM clearances?

Memphetic
05-05-2013, 12:50 PM
Install a real oil pressure gauge (even if it's temporary) and go from there. Did the engine shop use OEM clearances?

I built it. Everything was mic'd and was good to go. Brand new crankshaft, new bearings.

Boost4VR4
05-05-2013, 12:52 PM
One tick on fresh oil isn't a big deal, it's thin from being warmed up. If you want to check for things, check lifter pinhole size, oil pickup tube hitting oil pan PCV valves missing.

futurevr4man
05-05-2013, 07:05 PM
what weight of oil are you using? my engine has low pressure (judging from the stock gauge) if i use 10w30 or the like, but if i run 20w50 then it seems to be a lot better. ray recommended to me to run 20w50 for what its worth, and he built my engine

R/T93
05-05-2013, 07:14 PM
How could you possibly not have an aftermarket oil pressure gauge so you dont have to ask this question? What do you have in this motor build? 7, 8 grand? More?

What did it used to be before the rebuild? I mean, if its still the same sender with the same wiring. If its reading lower, the pressure is lower, period.

Memphetic
05-05-2013, 10:42 PM
How could you possibly not have an aftermarket oil pressure gauge so you dont have to ask this question? What do you have in this motor build? 7, 8 grand? More?

What did it used to be before the rebuild? I mean, if its still the same sender with the same wiring. If its reading lower, the pressure is lower, period.

No clue. I never drove the car before this. I bought the car as a rolling shell. I honestly think there may be a loose connection on the oil sending unit because it can be disconnected extremely easily. If it works on frequency (which it seems it does, since then pressure doesn't change immediately when revving), it could be missing counts. However, the oil pressure was very good just two days ago.

And yeahhhh.. I'd say I have a lot of money in this build... but I never thought to get an aftermarket oil pressure gauge :-P I'd like to find one that can replace the stock gauge in the stock position and possibly one that has a 0-5V output so I can log it with AEM. Anyone have a suggestion?? Preferably not AEM's $200 model :-P

R/T93
05-05-2013, 11:53 PM
Greg E found out that the wire to the sender wears out from the heat and the resistance through it changes the value the factory gauge spits out. If its easy (Im thinking no) replacing the wire may get the gauge working how it used to?

I have a 280 dollar DEFI gauge and wouldnt run anything else, but thats just me :)

donniekak
05-06-2013, 12:10 AM
On my last stealth tt the stock gauge showed about where you are describing. I was slightly worried, and hooked up a real gauge. To my surprise I was at about 23psi at hot idle with 15w-40 oil.

Memphetic
05-06-2013, 12:39 AM
I'm also thinking of moving to a thicker oil as well... Perhaps a 15W40 or 15W50. I HIGHLY doubt I will ever drive this car in winter.

vroom4
05-06-2013, 12:41 PM
1. Go to autozone, buy 15$ gauge and an adapter.

I dont understand some people on this forum. Its 15 freaking dollars for the cheapo gauge, just hook it up and disconnect it after you verify OP.

Turbo Beast
05-07-2013, 08:41 AM
Exactly, find the ugliest gauge in that store and mount it. They are 15 to 25 bucks, I just installed one in my car just to be sure, my oilpressure seemed low on hot idle.

Theyre ugly as sin but work great.

Greg E
05-07-2013, 10:28 AM
Greg E found out that the wire to the sender wears out from the heat and the resistance through it changes the value the factory gauge spits out. If its easy (Im thinking no) replacing the wire may get the gauge working how it used to?

I have a 280 dollar DEFI gauge and wouldnt run anything else, but thats just me :)

Its very easy to swap out.

Memphetic
05-07-2013, 11:45 AM
The wire is very easy to swap out indeed. I'm pretty sure I just need to accept what's going on and pull the oil pan.

I believe I hear a sound in the lower part of the engine that sounds a bit like knock (though it's not very loud at all). I noticed my knock sensor doesn't work after taking the car out for the first test drive to tune the fuel map (where it went lean a few times). I've drained the oil and there was nothing at all in it. Re-filled the oil yesterday and ensured that the connection between the sending unit and the wire was secure. I highly doubt that the sending unit/wire went bad in a matter of two days.

Pretty sure I likely smashed a rod bearing. Luckily enough, I have a spare set of Clevites sitting here. I'll just pull the oil pan.

familyMAN
05-07-2013, 11:45 AM
Cheap auto meter gauge/sender works for me.

vroom4
05-07-2013, 11:56 AM
The wire is very easy to swap out indeed. I'm pretty sure I just need to accept what's going on and pull the oil pan.

I believe I hear a sound in the lower part of the engine that sounds a bit like knock (though it's not very loud at all). I noticed my knock sensor doesn't work after taking the car out for the first test drive to tune the fuel map (where it went lean a few times). I've drained the oil and there was nothing at all in it. Re-filled the oil yesterday and ensured that the connection between the sending unit and the wire was secure. I highly doubt that the sending unit/wire went bad in a matter of two days.

Pretty sure I likely smashed a rod bearing. Luckily enough, I have a spare set of Clevites sitting here. I'll just pull the oil pan.

If you have an audible knock, bearings wont do you much...I feel like this statement is made like once a week on 3sgto/3si.

Toni
05-07-2013, 01:39 PM
Cut open your filter. Also, if you do find that one of yours bearings is shot there is a good chance you have shit all up in the oiling system. Turbos are easy to clog...

Memphetic
05-07-2013, 06:15 PM
Cut open your filter. Also, if you do find that one of yours bearings is shot there is a good chance you have shit all up in the oiling system. Turbos are easy to clog...

Did that as well. There's no bearing material anywhere in the engine.

familyMAN
05-07-2013, 07:27 PM
Did you put a real gauge on it yet??

AdamVR4
05-07-2013, 07:28 PM
Dont pull the pan without getting a gauge on it. Completely illogical.

Memphetic
05-07-2013, 10:34 PM
I'm still gonna put a gauge on it - but I GUARANTEE it has no oil pressure. It's illogical that the sender/gauge failed in the span of a day. They were reading fine the prior few weeks... I just don't want to get my hopes up when I know what's coming.

Greg E
05-07-2013, 11:35 PM
Okay... I won't tell you what you don't want to hear.... No problem.

donniekak
05-07-2013, 11:43 PM
Dont pull the pan without getting a gauge on it. Completely illogical.

Changing the oil a few times, and the rtv to reseal the oil pan is about twice the cost of a cheap oil pressure gauge. I don't understand why every 3s doesn't have a real gauge on it frankly.

Greg E
05-07-2013, 11:49 PM
Changing the oil a few times, and the rtv to reseal the oil pan is about twice the cost of a cheap oil pressure gauge. I don't understand why every 3s doesn't have a real gauge on it frankly.

Denial.

Chris@Rvengeperformance
05-07-2013, 11:55 PM
The stock gauges probably worked ok when the car was built, but here 20 years later they are a little moody. I don't exactly consider it a walk in the park to pull the oil pan on one of these, so I have no clue why you would do that (especially after cutting a filter open and seeing no bearing material) before even knowing what the real oil pressure is.

The biggest issue with the stock oil pressure gauge is for some reason it doesn't seem very linear. 20 PSI may be about 2 ticks, 3 ticks may be 25 PSI, but once you get to the first big line you are looking at almost 50 PSI. They just didn't scale the gauge very well, the low mark should've been damn near no oil pressure.

This is why a lot of new cars don't even have gauges. In lack of an accurate gauge people will sometimes jump to conclusions based on where the needle is. I'm sure some bean counter somewhere determined it was cheaper to have a few blown engines from oiling problems once in a great while than to constantly have people wanting their cars serviced because the gauge seemed "low"

Greg E
05-07-2013, 11:58 PM
The stock gauges probably worked ok when the car was built, but here 20 years later they are a little moody. I don't exactly consider it a walk in the park to pull the oil pan on one of these, so I have no clue why you would do that (especially after cutting a filter open and seeing no bearing material) before even knowing what the real oil pressure is.

The biggest issue with the stock oil pressure gauge is for some reason it doesn't seem very linear. 20 PSI may be about 2 ticks, 3 ticks may be 25 PSI, but once you get to the first big line you are looking at almost 50 PSI. They just didn't scale the gauge very well, the low mark should've been damn near no oil pressure.

This is why a lot of new cars don't even have gauges. In lack of an accurate gauge people will sometimes jump to conclusions based on where the needle is. I'm sure some bean counter somewhere determined it was cheaper to have a few blown engines from oiling problems once in a great while than to constantly have people wanting their cars serviced because the gauge seemed "low"

The main issue with the stock oil pressure gauge is the very slow response. It's accurate enough to tell you when there is a problem. Just like the coolant temp gauge.

Memphetic
05-08-2013, 11:43 AM
Exactly. The update rate is CRAZY slow... updates maybe once per second? Just makes for a generally ineffective device... hence the reason when you rev the car, the oil pressure will slowly creep up. It's not actually doing that - it's fluctuating with your engine speed. You just can't see it happening. A silly gauge in general.

Chris@Rvengeperformance
05-08-2013, 12:01 PM
I'm not sure why that is a huge problem. If you really need realtime pressure updates then start datalogging it. There are plenty of things to keep an eye on during a pull than your oil pressure gauge.

Greg E
05-08-2013, 12:05 PM
Can't wait to release the custom dash oil light chrome mod! :)

Memphetic
05-08-2013, 04:42 PM
Okay... I won't tell you what you don't want to hear.... No problem.

What are you not gonna tell me, btw? :-P

Memphetic
05-11-2013, 12:01 PM
No pressure. Hooked up a mechanical gauge and it doesn't even have enough oil pressure to fill the line. Oil pan is coming off next week (studying for finals this weekend).

anyonebutme
05-11-2013, 07:31 PM
sure you have enough oil?

Memphetic
05-11-2013, 10:56 PM
I literally drained and replaced it with 5 quarts right before hooking up the gauge :p

stealthee
05-12-2013, 12:46 AM
We were talkling about this in chat and I brought up the point that no copper + suddenly no oil pressure sounds like a faulty oil pump.

anyonebutme
05-12-2013, 02:00 AM
my car has been doing this thing where when it's really hot i loose pressure, like 6 psi. i figure it's just the relief sticking open after a track session.......always goes back to normal after cooling down. If you do pull the pan, pop the relief valve out and have a look. Only happens after like 20 minutes of beating the piss out of it for me. I don't worry about it because I'm never at idle while beating the piss out of it.

Memphetic
05-17-2013, 10:12 PM
Got to work on my car today now that finals are over. I wanted to make sure it was in fact the oil pump before I tore everything down, so I disconnected the front turbo drain line and started the car up. Sure enough, not a drop of oil came out.

Bad news is... it WAS my oil pump. Good news is... it's because I'm an idiot. I pulled the oil pan and discovered this:
5407

Are you supposed to loctite the oil sump? I have no damn idea how the bolts came loose - I assume they vibrated loose. Could be due to the fact that I have solid motor mounts and don't have a harmonic dampener. One completely came off, the other is loose. What an oversight.... :shake2:

stealthee
05-17-2013, 10:23 PM
That will do it.

sergechronos
05-17-2013, 11:26 PM
Hmm..FSM doesn't say anything about putting loctite on them. I'm curious to hear what others have to say though. Never seen them back out like that though.

donniekak
05-18-2013, 01:23 AM
Time for a rebuild.

aaronatstate
05-18-2013, 01:26 PM
Mine are not loctited in. Been running my car with 2 solid mounts and 2 stock mounts since Nov of 2009. 45,000 miles and the pan has been off twice and I have not had this issue. Are you sure you torqued them down?

Primus101
05-18-2013, 01:56 PM
#7 bolts?
If so, I've had them stretch prior to recommended torque when re-used. Buy new ones. I would tend to use ARP bolt lube for proper torque in the first place, as opposed to locktite. Loctite can create problems when used in higher heat locations.

NOMIEZVR4
05-18-2013, 02:05 PM
whoo...man that is scary.

TurboSinceBirth
05-18-2013, 02:49 PM
Looks like the bolts were plain neglected to be tightened down at all. I've never had a problem with the bolts backing out or anything. It doesn't even require much torque to tighten them up either.

Memphetic
05-18-2013, 08:31 PM
5408
5409
5410

And God smiled. :-P

sergechronos
05-18-2013, 08:39 PM
5408
5409
5410

And God smiled. :-P

You should go play the Powerball with that luck lol

Primus101
05-18-2013, 08:45 PM
Lucky you...what oil were you running?

Replacing the shells?

Memphetic
05-18-2013, 10:19 PM
I ran about a half a quart of Lucas in it. The reason being was "I've spun a lot of bearings, you never know." I never run that shit... but seriously... awesome. I couldn't be happier. Replaced the bearings today with a set of spare clevite 77's I had laying around - will report when I get oil tomorrow :P

aaronatstate
05-19-2013, 11:00 AM
Did you check the main bearings?