PDA

View Full Version : 3.7L down for the count again



Trevor
09-30-2010, 03:09 PM
First off...after adding up all the money in the car (you would NEVER believe how much!) there's no way I can just sell it for what I could probably find a buyer for. So breathe easy...I'm keeping it and I apologize for scaring you guys. :) I'll give whatever time I have but it's just going to move down the priority list a little.

So...shortly after this awesomeness:
http://www.3sgto.org/showthread.php?1069-597-AWHP-600-lbft-15.8-psi
...I am yet again stuck with a hurt car. I lost 14-15 psi of oil pressure at 2000 rpm after a pull. This isn't the first time either. Last time it happened at just 19 psi and hardly any timing (before I even started advancing it). I pulled the pan down and found the center mains had wear all the way around (but weren't smashed). The crank journals were fine. I replaced all the main bearings with ones that were tighter for more support (I went to stock 6G74 clearances), switched from 0w-40 to 5w-50 oil for more film strength, dropped the rev limiter from 8340 to 7100 (I thought maybe the high RPM was the issue), and dropped the boost from 19 to 16 psi to start tuning. After getting it back together I took note of the oil pressure at 2k (64-68 psi at 2k) so I could watch it very closely. I thought I was out of the woods and was pretty psyched after hitting 600 tq but obviously I wasn't. I'm sure this time once I pull the pan again I'll find center main bearing wear again.

Now I was thinking that maybe the 6G75 cranks are weak and it was flexing from power. On the other side...in the back of my mind I was thinking that Italo Grasso did 774 tq on the same crank so WTF.

I talked to Ray P just now and he had a good point. He's wondering if maybe my old school machine shop didn't balance the assembly properly. It makes sense since it's 360 degree bearing wear and not just wear/smashing at the bottom.

So where to now? Well...obviously this crank is probably cracked all to hell. I could have the balance checked by another reputable shop and just get another (properly balanced) stock crank if it checks bad. Or I could just go with a custom 4340 grade forged steel crank made by one of our pioneering vendors that will be announced soon. Stay tuned! :)

onebadmollafolla
09-30-2010, 03:10 PM
w00t! He's keeping it! You'll get it going better than ever. ;)

Subscribed. :D

pos-vr4
09-30-2010, 03:40 PM
the way you describe the issue, kinda sounds like a bent crank.

BTW when my machine shop dose the 6g72 balance my invoices always say V6 "split throw" balance on them. makes me wonder what they need to do differently Vs a regular balance job.

green-lantern
09-30-2010, 03:47 PM
:) I'm glad your keeping it man!

:( Sorry about the crank problems though.

mb7050
09-30-2010, 03:48 PM
glad to hear your keeping it !

sorry for the problems

Chris@Rvengeperformance
09-30-2010, 04:04 PM
glad to hear you are sticking with it. I'd send the shortblock to ray and see what he can do for you, it may be cheaper and a lot less headache in the long run.

TT Eric
09-30-2010, 04:46 PM
Sorry and happy at the same time! I'm glad you keep your car, you're and outstanding member.

Eric

JasonY
09-30-2010, 05:23 PM
I believe Matt M is selling his stroker that was just refreshed...

Glad to see you sticking it out with the car but sorry to hear about the problems with it.

Jason

jba3
09-30-2010, 05:23 PM
glad to hear you are sticking with it. I'd send the shortblock to ray and see what he can do for you, it may be cheaper and a lot less headache in the long run.

My thoughts exactly. If you don't have the time, put a little money into Ray's hands, and he'll get you running even faster than the already ludicrous speed you have.

oohnoo
09-30-2010, 05:23 PM
#1 Glad your keeping your car
#2 So I take it you're going to help out with this? ;)

Or I could just go with a custom 4340 grade forged steel crank made by one of our pioneering vendors that will be announced soon. Stay tuned! :)

OhioSpydersKid
09-30-2010, 05:27 PM
I literally peed my pants when you said you were going to sell her! I felt like a creeper watching your build video haha.

Glad to see your keeping her and I hope all goes well! Can't wait to see what kind of power it puts down after yet another tear down. ;)

Zach.

Trevor
09-30-2010, 05:43 PM
#2 So I take it you're going to help out with this? ;)
I called him yesterday. :p

familyMAN
09-30-2010, 07:03 PM
Damn you are dedicated! Good luck!

Lithium
09-30-2010, 07:46 PM
Way to stay in it man, never give that up! Oh and I need a link to this build video????

CoreyB
09-30-2010, 07:51 PM
Wonder if the crank is bent but balanced.

Trevor
09-30-2010, 08:06 PM
The crank was brand new from the dealer and unlike most of them I've recieved this one arrived in a box that wasn't in horrible shape. I asked the shop to check it for straigtness even though it was new. I didn't verify that they had done it when I picked up the balanced, ready to install assembly. Maybe that was one of the few times when it would have been OK to insult them by asking. I think they would have told me it was checked & good regardless since they had already said it was ready for pickup.

If it was bent do you guys think it would have been good for 1000+ miles of normal driving? I had no issues until I put my boot in it, revved it over 4500, and started making 550+ Tq.

Mean Green
09-30-2010, 08:16 PM
I am noticing that the smallest of debri particles are to blame for simple bearing washout with 6G series engines. I used a twin Purolator oil filter setup with this last build that I did but before anything, I literally made a make shift clean room to assemble the engine in. I built the engine in the cleanest environment possible and BAM whada ya know...I checked the bearings and despite my best efforts, 1 piece of debri managed to go around the bearings of rod 3. I am throwing another set of Bi metal bearings in it since they can handle any possible debri better than tri metal bearings. All the other bearings looked great which was a nice sight. I don't know what bearings you are using or how the environment is that you are cleaning / assembling the parts in but that's all it takes is a small fragment. Take your oil pan to the machine shop and have it cleaned along with your valve covers.

I also noticed that washout is happening within or before 500miles. I also tore apart both my filters and they where full of shit but as I said, the rest of the bearings looked great. This build was also the first time I used a twin filter setup.

CoreyB
09-30-2010, 08:16 PM
I dont really know man. You are far more knowledgeable with these than I. It was just a thought. Seems being out of balance should of worn the outer mains as well. But Ray has seen more bottom ends than a doctor so he's probably right about the balance.

OhioSpyderman
09-30-2010, 08:19 PM
I know you're looking for answers at this point Trevor, but I would like to reiterate my son's (OhioSpyder'sKid) feelings that I'm glad you're sticking with this....

You always have, and will continue to be a VERY positive force for our platform (Thank You)

Bob.

P.S. I felt like a creeper watching you as well ;)

OhioSpyderman
09-30-2010, 08:21 PM
I dont really know man. You are far more knowledgeable with these than I. It was just a thought. Seems being out of balance should of worn the outer mains as well. But Ray has seen more bottom ends than a doctorso he's probably right about the balance.

That's just WRONG on so many levels....but probably TRUE :)

Bob.

CoreyB
09-30-2010, 08:24 PM
On second thought if the balance issue was towards the center it would wear those first, then transfer to the rest. So they were even all the way around ? What was the oil clearence to start and did you happend to check when they were worn to see how much it wore ?

mcshooter
09-30-2010, 09:11 PM
one engine i had where the center mains showed the same the crank was bent. its easy to check, remove gridle and use a magnetic base with a indicator and spin the crank. my crank was bent over .025 .. hard to believe

deemo99
09-30-2010, 09:51 PM
I too am glad you are keeping with it! Interested in crank info when you can make it public or did I misunderstand and you are or have purchased Matt's umm crank:)?

Mikes2nd
09-30-2010, 10:04 PM
ill buy it for ... eh ill give you 10k for it :)

CoopKill
09-30-2010, 10:09 PM
Good to here you are sticking around!

I'm sure I don't have a 1/4 what you do in mine, but I think I am at the point of no return already. Lifer!

Jeremy C
09-30-2010, 11:34 PM
If you want another set of hands to help out, you know how to find me. I'd be more than glad to volunteer some time and get to know one of the more famous 3S guys. :)

Apache
09-30-2010, 11:39 PM
Glad to hear that you're keeping the car Trev. Sorry to hear about the crank problems though. I'm sure you'll get it figured out though.

And as for Matt's crank, I don't think Trevor is looking at buying Matt's because he stated that the one he was looking at was 4340 chromoly. The stroker that was in Matt's drag car IIRC is made of EN30B. Someone correct me if I'm wrong though.

NOMIEZVR4
10-01-2010, 01:54 AM
I am noticing that the smallest of debri particles are to blame for simple bearing washout with 6G series engines. I used a twin Purolator oil filter setup with this last build that I did but before anything, I literally made a make shift clean room to assemble the engine in. I built the engine in the cleanest environment possible and BAM whada ya know...I checked the bearings and despite my best efforts, 1 piece of debri managed to go around the bearings of rod 3. I am throwing another set of Bi metal bearings in it since they can handle any possible debri better than tri metal bearings. All the other bearings looked great which was a nice sight. I don't know what bearings you are using or how the environment is that you are cleaning / assembling the parts in but that's all it takes is a small fragment. Take your oil pan to the machine shop and have it cleaned along with your valve covers.

I also noticed that washout is happening within or before 500miles. I also tore apart both my filters and they where full of shit but as I said, the rest of the bearings looked great. This build was also the first time I used a twin filter setup.

Wonderful information...Thanks very much!

VR-4 0wnz j00
10-01-2010, 04:36 AM
Good to see you came to your senses, lol. It really sucks this is the case but I know youll enjoy it when its running again.

GTO Assassin
10-01-2010, 06:03 AM
There's got to be a point where you've spent and poured too much into something, that you really can't part with it. I'm guessing you've gone past that mark several times over. (and then some) It still amazes me that after all the work you have done with your Stealth, that you come back to the forums and ask us what we think. :)

Scotty

Jimvr4
10-01-2010, 05:13 PM
Glad you're still dedicated to the platform. It takes a lot of knowledge, determination, and money to go as far as you already have :D

TurboSinceBirth
10-01-2010, 08:13 PM
I knew you'd change your mind about getting rid of the car. :D The heartache of all the work that has to be done to fix a car sometimes isn't as bad as knowing how much you will lose selling the car. If it doesn't hurt anything to let it sit it's always a good idea. I always try to pay cash for anything that isn't my main source of transportation that way if it's down I'm not out anything.

That's interesting what you found out about the engine from the bearing. Ray's probably right about it not being balanced. I don't know enough about it to tell for sure. At least you didn't have knock, oil starvation, dented oil pan, or oil contamination spin the bearings like many people have happen. After getting screwed through a local shop turning my 6G72 crank that was cracked which they were supposed to magnaflux, I made sure Ray did all the work on my crank and balancing through Scott Merkel. I don't trust anyone around here and if I have problems with coolant being pushed out I'll bet it'll be the shop screwing up the copper o-rings. I hope it all works out ok. :(

I really hope switching to the 4340 crank will solve your problems and it's not some other underlying reason. I'd hate to see you keep going through rebuilds not being able to pinpoint the exact problem. I'd say you should buy Matt's stroker and not worry about the 0.2L downsize. Maybe later you could put bigger pistons in, but I'd just enjoy the car for awhile. :) I'll look forward to your results.

L_P
11-09-2010, 10:29 PM
Any word on this trev?
-John

DocWalt
11-09-2010, 11:25 PM
I was just wondering where Trev has been recently. :bump:

Mikes2nd
11-10-2010, 12:39 AM
he is hopefully taking a break from the car :)

J_Parker
11-10-2010, 01:57 AM
I would say bent crank as well. Also glad to hear you're keeping the car! I've followed your build almost to the point of religeon ;)