View Full Version : 3.5 DR750 build
Lugnut
04-11-2013, 01:59 AM
Just putting it out there the build is complete and the car is officially running .. Be on the street tomorrow ..
I wanna give a really big "Thank You" to Monchrome and JasonY who put in alot of time over the last few days putting the engine together and getting the install done ..
What a sleeper
The new
Merkel built 6G72 3.5
DR Stage 3 heads ..pinned
Unorthodox Racing Cam gears
Fully built trans containing
Quadco output shaft
Quaffe front diff
Bellhousing brace
Broomfield Endcase
AEM fuel pressure gauge
Billet oil pump gears
Deleted atmosphere Tial for a recirc Tial
Basically replaced the entire old setup with brand new everything ..Deleted Meth injection ..
This week after a shake down and break in I am swapping the springs for Megans and dropping 255/40/18 KDW's on.. Swapping the 255 for a Walbro 400 .. Adding the Ooga horn.. and swapping in the overclocked ECU ..
Car will be run on pump gas or 100/104 unleaded which is readily available less than a mile away from the house ..
Merkel 6G72 3.5
DR Stage 3 Heads w/ High Rev Spring Kit .. Pampena pinned .. Stock Cams
DR Port and Polished lower plenum
DR Tial 750's w 18psi forge wastegates
DR Arc-2 92mm
Unorthodox Cam Gears
IPS 750hp Anodized Precision Core Frontmount and hard piping kit
Overclocked (8100 Rpm) ECU (Current) .. Chrome on the shelf
Southbend Stage 4FE clutch
Rps Lightweight Flywheel
Greddy Boost Controller
AEM Digital Gauges (oil- fuel -temp -boost- wideband)
99 Lifters
IPS Setrab 25 row Oil Cooler
PTE 680 injectors
KB Boost a pump (Installed but not in use)
HKS DLI
Walbro 400 fuel pump
AEM FP regulator
3SX fuel rail loop
Ninja Performance Black Nylon Fuel kit
IPS downpipe
Tial recirc BOV 11psi spring
Tein S-tech springs .. Swapping to Megan Coilovers anyday
Carbotech Rotors
Hawk Pads and Stainless brake lines
Pampena Bellhousing Brace
Quadco output shaft
Quaffe front diff
Bellhousing brace
Broomfield Endcase
Jack Hammer 7 quart oil pan
Billet Oil Pump Gears
Maximal Solid motor mounts front and rear
Maximal Performance Adjustable Control Arms
Ebay 4" Megan knockoff exhaust
Krank vents
Stock 18 Chromies w/ KDW 255/40ZR18's
1 Oooga horn ;)
wingnut
04-11-2013, 02:06 AM
Sounds like a beast...in for pics :D
AdamVR4
04-11-2013, 12:05 PM
Can't wait to see pics... What turbos did you have before? Did you degree/zero the cams? Very jealous of your UR cam gears ;)
How does Ray/Merkel recommend breaking in the 3.5 6G72?
Ah, 'bated breath, and all that...:)
Greg E
04-11-2013, 12:28 PM
Win!!!
Chris@Rvengeperformance
04-11-2013, 12:37 PM
looking forward to the results
That should be a killer street car!
vr4tune
04-11-2013, 04:26 PM
Now your turbos are too small for that huge engine.
Greg E
04-11-2013, 05:22 PM
Now your turbos are too small for that huge engine.
Negative.
The setup is absolutely perfect for a street car.
HilbillyHomeboy
04-11-2013, 05:25 PM
That's going to be a wild ride. Well done on the choices. Keep us updated, please! :)
Jeremy
TurboSinceBirth
04-11-2013, 05:33 PM
I talked to Matt about this on the phone awhile ago and he thinks the stock intercoolers and exhaust he had was more of a restriction on his 3.5L DR-750 car than the motor itself. I thought it choked off the turbos but he thinks differently.
Todd, did you make the switch to a flashed ecu yet or are you going to run race gas for awhile with the ARC-2 until you make the switch?
ChargerX3
04-11-2013, 06:44 PM
Thread needs pics.
Greg E
04-11-2013, 07:22 PM
I talked to Matt about this on the phone awhile ago and he thinks the stock intercoolers and exhaust he had was more of a restriction on his 3.5L DR-750 car than the motor itself. I thought it choked off the turbos but he thinks differently.
Todd, did you make the switch to a flashed ecu yet or are you going to run race gas for awhile with the ARC-2 until you make the switch?
Just the ARC for now. Dude has a spare 98 VR4 ECU in his basement and a BlackStealth PnP harness.... Keep trying to get him to do the change over.
i have yet to see a dyno chart that convinces me that 750's will not choke on a 3.5L engine. matt m's certainly didn't appear that way.
AdamVR4
04-11-2013, 07:45 PM
i have yet to see a dyno chart that convinces me that 750's will not choke on a 3.5L engine. matt m's certainly didn't appear that way.
define 'choke'
Chris@Rvengeperformance
04-11-2013, 09:03 PM
displacement aside peak horsepower will be the same and the powerband will be wider.
define 'choke'
based on HP vs. torque. the numbers on his pull (to my recollection) were indicative of the turbo gasping at higher rpm's.
Chris@Rvengeperformance
04-11-2013, 09:07 PM
based on HP vs. torque. the numbers on his pull (to my recollection) were indicative of the turbo gasping at higher rpm's.
why would you think that when horsepower is basically a function of airflow?
if i can find the original thread, i'll remember what the discussion was about.
Chris@Rvengeperformance
04-11-2013, 09:14 PM
I mean you guys are saying that a larger displacement engine has greater exhaust flow for the SAME horsepower.
because....magic??
i don't remember the original thread, forest. i just remember that it had like a lower HP figure, but a TQ that was 100 or so higher. or maybe vice-versa. either way, the numbers didn't match up like one would have expected--and i think matt said he thought it was because of the 3.5L.
Greg E
04-11-2013, 09:19 PM
:lol: Internet mechanics....
Well I Dynoed it tonight on Ray Luna's new AWD Dynojet in El Paso.
21psi, pump gas/water meth tune
566whp
624 wtq
The car really has one hell of a power band, peek TQ comes in at ~4100rpm, and Peek HP at ~5100 rpm and the HP stays almost totally flat with almost no drop off to 7200rpm were I was ending the runs. Talk about a TQ monster!
Here is the funnest part, as you all know the car still has stock intercoolers on it, well the only fan thy had was a little house fan blowing at the front of the car ZERO air was going to the inercoolers. Meaning thy were doing nothing, it made this power for the most part non intercooled. I can only imagin how hot the air was going into the motor but you could have fried a egg on the IC's or IC piping after the pull.
Thy are suppose to E-mail me the Files , I'll post up the charts then.
I also have them E-mailing me a dyno chart from a DBB T67 supra that made 520 whp on there dyno (there old dyno record before last night) you should see that overlayed hahahaha, I have so much more usable power it's not even funny.
Power Mod list
3.54L stroker
DR Stage 3 heads
DR street/strip cams
UR cam gears
DR 750 Stock housing bolt on turbos
DR down pipe
Tanabe Concept G Blue Exhaust
HKS twin power
ARC-2 with 92mm MAS
Denso 720cc injectors
Denso pump
KB boost-a-pump
Snow stage 2 boost cooler
Blitz DSBC ID3
DN Y-pipe
Edit Dyno chart added, here is a pic my buddy took of the screen, ya ya I know it ses White 240sx in the file, that's because thy did not open up a new folder for my car. Note take a look at that nearly totaly flat A/F, god I love the ARC-2:)
http://www.dynamicracing.com/mw/images/3/3e/CIMG2736.JPG
car on the dyno, and me hooking up the tac lead
http://www.dynamicracing.com/mw/images/2/24/CIMG2713.JPG
DR750 bolt on turbo
http://www.dynamicracing.com/mw/images/f/fe/DR750_turbos_001.jpg
Motor shot, Looks stock hu?
http://www.dynamicracing.com/mw/images/5/5b/6spd_006.jpg
Chris@Rvengeperformance
04-11-2013, 09:22 PM
Kids these days.
thanks, greg.
i was right, the HP figure is low on that run. it's flat, certainly, but not what was expected. and if memory serves, matt had initially pointed to flow at higher RPM's for the lower #.
nothing wrong with that, mind you. flat is much more "streetable" in my opinion.
Chris@Rvengeperformance
04-11-2013, 09:31 PM
yeah no kidding, it is only 21 PSI. It is a pump/meth tune.
R/T93
04-11-2013, 09:32 PM
566 low for 21 psi? You know these turbos can do like 32 psi....
TurboSinceBirth
04-11-2013, 09:33 PM
All of the 600AWHP runs were 25-28 psi on stock and built motors when these first had numbers put out. Nobody ever pushed it hard on a stroker.
JasonY
04-11-2013, 09:37 PM
Gonna be a blast :)
Jason
Chris@Rvengeperformance
04-11-2013, 09:40 PM
Remind me of when Phillip said that the strokers would "drive like a tractor"
JasonY
04-11-2013, 09:44 PM
Well, it should have a similar power delivery as my 6.0 Powerstroke..lol
Jason
Greg E
04-11-2013, 09:46 PM
All of the 600AWHP runs were 25-28 psi on stock and built motors when these first had numbers put out. Nobody ever pushed it hard on a stroker.
Yep. The community HOUNDED him for testing these turbos on a stroker so he had to switch back to a stock motor. Matt believes there is still more left in the turbos. Too bad he never did race gas/ethanol to find out.
Here's his results on a stock 3L motor.
Well you guys asked for it so here you go, I drove to Albuquerque today 230 mile each way in my street stealth to dyno it with the Bone stock 3.0L 80,000 mile motor.
I am running a mix of 25% C16 and 75% 91 pump, and a Snow stage 2 boost cooler.
First pull right off the street 23psi of boost
http://www.dynamicracing.com/mw/images/7/7f/DSC00027.JPG
And the 3rd pull I upped the boost to 25psi
http://www.dynamicracing.com/mw/images/a/a6/DSC00028.JPG
That's right over 600 WHP on a totally stock 3.0L, out of Direct bolt on TD-04 turbos.
Edit, Mod list added below
DR750's
Denso Fuel pump
hot wired
with a KB boost-a-pump
Denso 660cc injectors
Splitsecond ARC-2 with 92mm MAS
DR Down pipe
Tanabe Cat-back
Blitz DSBC ID3
HKS Twin Power DLI
ETS FMIC
RPS Flywheel
RPS 6 puck MAX clutch
AEM Wide Band
Defi Blue racer boost guage
DN intake pipes
Snow Stage 2 boost cooler
futurevr4man
04-11-2013, 09:48 PM
All of the 600AWHP runs were 25-28 psi on stock and built motors when these first had numbers put out. Nobody ever pushed it hard on a stroker.
i keep waiting on blackmount to come in here and say its stupid because he saw a 4 cylinder with 1 turbo (he would stress 2 less cylinders and 1 less turbo) make more horsepower.
then he would rave about how JDMtyte the FWD burnout was, and all the beetches threw their tops off :rolleyes:
Greg E
04-11-2013, 09:57 PM
i keep waiting on blackmount to come in here and say its stupid because he saw a 4 cylinder with 1 turbo (he would stress 2 less cylinders and 1 less turbo) make more horsepower.
then he would rave about how JDMtyte the FWD burnout was, and all the beetches threw their tops off :rolleyes:
:lmao:
Chris Wiemann is funny as shit!
HilbillyHomeboy
04-11-2013, 10:00 PM
yeah no kidding, it is only 21 PSI. It is a pump/meth tune.
Bingo. The big benefit that Matt loves(for good reason), more timing. Which is why peak tq is so early.
Jeremy
SnakeSkinner
04-12-2013, 12:06 AM
going to be a TQ monster!
Blackmount
04-12-2013, 12:20 AM
i keep waiting on blackmount to come in here and say its stupid because he saw a 4 cylinder with 1 turbo (he would stress 2 less cylinders and 1 less turbo) make more horsepower.
then he would rave about how JDMtyte the FWD burnout was, and all the beetches threw their tops off :rolleyes:
I seem to miss the part of where this had to do with anything that was said. IMO u posting randomly in a thread just to make fun of someone who has yet to even look at this thread is dumber then anything I have ever said or done. I probably would have never even opened the thread if someone didnt bring this posts to my attention. Tisk tisk. Do u have a crush on me or something? U seem to be obsessing over things i do or say like a school girl and bring my name up whenever u have the chance. Do you feel better now that u made fun of someone else for something stupid?
I mean u block me because i am "annoying" and "stupid" yet u wont stop bringing up my name. Are you a closet homosexual?
Lugnut
04-12-2013, 12:28 AM
Minus a bath the car is officially done and on the ground .. I swear when I looked under the car I saw the transfercase shaking in fear .. Depending on weather Im gonna get her out of the garage and go for a drive and hopefully get you guys a youtube video so you can hear her .. This car sounds so sick .. I feel so blessed ..
Can't wait to see pics... What turbos did you have before? Did you degree/zero the cams? Very jealous of your UR cam gears ;)
How does Ray/Merkel recommend breaking in the 3.5 6G72?
All turbos are and have been the first gen Tial DR750's ... The cams are OEM and straight up as I want to get the platform some solid results on the dyno .. Gonna take the car to Ray and have a straight up before and after dyno for just the cam gear adjustment .. Was also wanting to do the meth on the dyno just to see results but sorry guys, since I had no intentions of ever running it again I just said screw it and deleted it literally last minute while the engine bay was empty .. As for break in its a warm up and drain all oil and filter, then run it around for 500 or so and drain it all again .. Rinse and repeat as needed ..
I talked to Matt about this on the phone awhile ago and he thinks the stock intercoolers and exhaust he had was more of a restriction on his 3.5L DR-750 car than the motor itself. I thought it choked off the turbos but he thinks differently.
Todd, did you make the switch to a flashed ecu yet or are you going to run race gas for awhile with the ARC-2 until you make the switch?
I have the gear to do the flash tune today .. But since I had Turbo Bob overclock a ECU for me before the flash tuning came around I've basically decided to run that once this shakedown is over and let Greg finish his car and do the tune all up and then I will prolly make the switch .. 8100 RPMs will give us top end Dyno results on these turbos .. And dare I say it flash ECU as well ..
I will compile a mod list on the first page of this thread over the next few days .. I have done so much to it I cant really remember everything off the top of my head ..
And for everyone we stayed on stock cams so the spool on this car should be rediculous and to the left of all Stage 3 head DR750 dyno results .. I have this setup married to the IPS frontmount with the 750 HP spearco core and the IPS downpipe and Ebay megan exhaust ( I cant recall its exact name) .. Greg Cerakoted the mani's and cats for me and we will see over time how well that performs and holds up ..
I bought a SouthBend Stage 4 replacement disk and new flywheel segments for the car, but just a heads up it appears that the old disk has uneven wear on the flywheel side .. And when I say uneven I mean the clutch side looks new .. And the flywheel side looks worn out .. No blueing on the RPS flywheel itself which means, as I understand it, the clamping force on this clutch is just not enough for this car .. IDK .. We will see for sure this time around and maybe change up to something else ..
As for the engine I think its pretty safe to say we arent 100% sure what the turbos will do on this 3.5 but I feel confident after having the 3.0 that this setup will be exactly what I was hoping for .. Like all of you .. Im totally in for Dyno results :) .. Just a few miscellaneous pics ..
http://i230.photobucket.com/albums/ee213/tazz_375/882.jpghttp://i230.photobucket.com/albums/ee213/tazz_375/852.jpghttp://i230.photobucket.com/albums/ee213/tazz_375/879.jpghttp://i230.photobucket.com/albums/ee213/tazz_375/844.jpghttp://i230.photobucket.com/albums/ee213/tazz_375/931.jpghttp://i230.photobucket.com/albums/ee213/tazz_375/924.jpg
Chris@Rvengeperformance
04-12-2013, 12:35 AM
yummy
Lugnut
04-12-2013, 12:43 AM
going to be a TQ monster!
Matt .. Thank You for everything !!!
anyonebutme
04-12-2013, 01:11 AM
lol @ greg humping engine. it's like the standard 3S engine pic, lmao.
i still love your FMIC setup.
AdamVR4
04-12-2013, 11:45 AM
i was right, the HP figure is low on that run.
LOL, no. 21 psi @ 566 AWHP on gasoline with meth injection on TD04's in NO WAY supports your position that DR750's "choke" a 3.5L.
Blackmount
04-12-2013, 04:29 PM
http://i230.photobucket.com/albums/ee213/tazz_375/882.jpg
Okay, Lets be serious...
How much Tacobell did he charge you?
futurevr4man
04-12-2013, 07:49 PM
I seem to miss the part of where this had to do with anything that was said. IMO u posting randomly in a thread just to make fun of someone who has yet to even look at this thread is dumber then anything I have ever said or done. I probably would have never even opened the thread if someone didnt bring this posts to my attention. Tisk tisk. Do u have a crush on me or something? U seem to be obsessing over things i do or say like a school girl and bring my name up whenever u have the chance. Do you feel better now that u made fun of someone else for something stupid?
YES
I mean u block me because i am "annoying" and "stupid" yet u wont stop bringing up my name. Are you a closet homosexual?
DOUBLE YES
lol at the greg humping the engine too, thats great. your piston design is neat, what is the compression ratio? 8.0:1?
Lugnut
04-12-2013, 09:07 PM
http://www.youtube.com/watch?v=NBif-FwXq1Y&feature=youtu.be
Blackmount
04-12-2013, 09:23 PM
nice bov, is that a Tial? real or knock off?
Chris@Rvengeperformance
04-12-2013, 09:29 PM
Sounds beastly
JasonY
04-12-2013, 09:41 PM
Its a real one, its the new QR and recirculated.
Jason
wingnut
04-12-2013, 11:52 PM
lol @ greg humping engine. it's like the standard 3S engine pic, lmao.
Agreed, as a matter of fact...
If you DONT have a pic of you in some position that looks like you are humping a 3s, then you either; a) havent been around long, or b) dont work on your own things enough :lol:
Chris@Rvengeperformance
04-13-2013, 12:04 AM
Its a real one, its the new QR and recirculated.
Jason
99% chance that is the bov I'm going with. This metal evo bov really makes my car jerk sometimes going off throttle.
Vishnu
04-13-2013, 02:04 AM
http://www.youtube.com/watch?v=NBif-FwXq1Y&feature=youtu.be
What part of MD are you from?
Lugnut
04-14-2013, 11:29 PM
Im over in Rehoboth Beach these days ??
Vishnu
04-15-2013, 01:20 PM
Ah, I haven't been out that way in a good while, I'm closer to the capital beltway, between b'more and dc. Your build is making me seriously consider the stroker even more though.
Greg E
04-15-2013, 01:24 PM
Ah, I haven't been out that way in a good while, I'm closer to the capital beltway, between b'more and dc. Your build is making me seriously consider the stroker even more though.
I'm honestly amazed more people don't run the stroker. There are absolutely no down sides to it and for the price, its an amazing deal!
Vishnu
04-15-2013, 02:07 PM
I didn't really want the extra plumbing costs associated with turbo upgrades, but if I can stay TD04, it's not a bad deal pricewise.
Greg E
04-15-2013, 02:35 PM
I didn't really want the extra plumbing costs associated with turbo upgrades, but if I can stay TD04, it's not a bad deal pricewise.
Never understand why people think you can't run TD04s with a stroker....
AdamVR4
04-15-2013, 03:04 PM
Never understand why people think you can't run TD04s with a stroker....
It's because this 'choking' myth has been allowed to persist.
Vishnu
04-15-2013, 03:55 PM
It's because this 'choking' myth has been allowed to persist.
This. I've always toyed around with the idea, but have never really been serious about a stroker without a significant turbo upgrade, TD05 or bigger.
This. I've always toyed around with the idea, but have never really been serious about a stroker without a significant turbo upgrade, TD05 or bigger.
16g's and 3.5L seems like a match made in heaven to me. widowmaker sold me on it.
vr4tune
04-15-2013, 09:55 PM
Never understand why people think you can't run TD04s with a stroker....
i never thought that you can't. I just feel that it's overkill. Dr750s spool plenty fast on a 3.0l. Dr750s aren't the end all turbo. I'd rather have a dr1000-1200 kit on a 3.5l.
JasonY
04-15-2013, 10:03 PM
Its like driving a 13g's on 3L, just a whole lot more. Probably making lower 400's at 14psi right now. Had to add more fuel at wastegate pressure than 16-17psi on pump before...its moving a lot of air already...:)
Jason
TurboSinceBirth
04-15-2013, 10:11 PM
I'm honestly amazed more people don't run the stroker. There are absolutely no down sides to it and for the price, its an amazing deal!
Unless of course you mess up the crank and then it's a matter of whether or not you feel comfortable making power on a turned crank. I'm spooked but then again when I bought a stroker I knew I didn't want to run anything less than 700AWHP. It cost $1600 plus the purchase price of the 6G74 crank to get it machined and balanced so it's not like that's as cheap as buying a used forged 6G72 crank to have polished and balanced. I was one of the people that fell for the TD04 choke which is probably why since I got rid of the T3 setup I let the stroker sit in storage because I thought it would keep me from reaching the higher peak 600-650AWHP numbers with TD04s. I may give it a shot in transition to the next custom turbo setup.
Unless of course you mess up the crank and then it's a matter of whether or not you feel comfortable making power on a turned crank. I'm spooked but then again when I bought a stroker I knew I didn't want to run anything less than 700AWHP. It cost $1600 plus the purchase price of the 6G74 crank to get it machined and balanced so it's not like that's as cheap as buying a used forged 6G72 crank to have polished and balanced. I was one of the people that fell for the TD04 choke which is probably why since I got rid of the T3 setup I let the stroker sit in storage because I thought it would keep me from reaching the higher peak 600-650AWHP numbers with TD04s. I may give it a shot in transition to the next custom turbo setup.
ok, so it wasn't just me. i swear i was going to go with the 3.5L + 750 route, but matt m. or someone else convinced me that 16g's might be better. seeing widowmaker's results convinced me. plus, a pair of blown 16g's probably costs less than fixing one 750.
JasonY
04-15-2013, 10:24 PM
16g's used to cost less than 750's. Back when u could get a pair brand new for like 1100, it was a relative no brainer. But for how easy it is to build a TD04 car, its pretty pointless to go aftermarket manifold unless ur shooting for 700 or better at the wheels.
Jason
...or aiming to use pure pump and hit 600whp...
TurboSinceBirth
04-15-2013, 11:30 PM
ok, so it wasn't just me. i swear i was going to go with the 3.5L + 750 route, but matt m. or someone else convinced me that 16g's might be better. seeing widowmaker's results convinced me. plus, a pair of blown 16g's probably costs less than fixing one 750.
Back when Matt first dyno'd that was the consensus. Fast forward to a few months ago when I was having high crankcase pressure with the krank vents I talked to him on the phone and had mentioned I would have gone with a 3.5L + DR-750 setup if it wasn't going to lose peak power compared to a 3.0L + DR-750 setup. He said his stock side mount intercoolers and stock exhaust wasn't helping at all and that he believes it had quite a bit of power left since he was only at 21 psi. He told me if he built another street car that would be hands down what he would put in it 3.5L + DR-750s.
3.5L + 16Gs Steve only made 525AWHP on a 3.5L + 16Gs with pump gas only which was comparable to Ray's built 3.0L DR Stage III heads, cams, and DR-750s at 525AWHP on pump. However, on Ray's old chameleon car he sold to a guy that put a 3.5L + 16Gs in he made 665AWHP and 748AWTQ. That's definitely impressive. It will be interesting to see how much tq the 3.5L will let the DR-750s make.
I don't know how soon you plan to swap to the flashed ecu Todd but at least if you can hook up evoscan to your overclocked ecu you and Jason can get some VD dyno data before swapping in the flashed ecu if you don't really feel like tinkering with a more complex tune for awhile.
CoopKill
04-16-2013, 04:01 AM
I know where I am going next.
R/T93
04-16-2013, 12:28 PM
I know where I am going next.
I know where I'm going FIRST :devil:
From the phone.
familyMAN
04-16-2013, 02:58 PM
3.5L + 16Gs Steve only made 525AWHP on a 3.5L + 16Gs with pump gas only which was comparable to Ray's built 3.0L DR Stage III heads, cams, and DR-750s at 525AWHP on pump. However, on Ray's old chameleon car he sold to a guy that put a 3.5L + 16Gs in he made 665AWHP and 748AWTQ. That's definitely impressive. It will be interesting to see how much tq the 3.5L will let the DR-750s make.
Boost was dropping hard on the 16G 3.5. Ray said wastegates were likely blowing open but owner was satisfied as is. Possibly more power to be had in that setup. That wasn't pump though, was it??
Chris@Rvengeperformance
04-16-2013, 03:37 PM
Boost was dropping hard on the 16G 3.5. Ray said wastegates were likely blowing open but owner was satisfied as is. Possibly more power to be had in that setup. That wasn't pump though, was it??
e85...
hard to come up with an accurate comparison when some are running corn & others pure pump & still others on spray. boost levels are all different. some have virtually stock motor, some have heads, cams, etc. and if the gates are leaking, has it been tried with externals?
vTaKwiTHsLiCkS
04-16-2013, 10:34 PM
haha. damn.. when i told matt i wanted stroker and dr750s, he talked me out of the stroker.
boo.
nice build. : ]
Lugnut
04-17-2013, 03:33 AM
Tuned the high on the ARC2 yesterday .. Running Exxon 93 .. Started out with a few pulls on the street running into 12.5-12.7 at 5000 to 5500k and getting out of it .. Car registered no knock .. Got that straight with just a few clicks .. FFwd .. Took the car out and got into it a bit tonight .. Pulling 11.1-11.3 blips to 11.5 up top .. Forge wastegates set at 18 .. Actually showing 14 tipping into 15 psi on the digital .. New Sumitomo HTRZ II break in tires .. Car full weight with a passenger .. 2 runs .. Identical results .. 1st thru 3rd gear from a 5mph roll .. Pedal to the floor car spins all of first and hooks second and third .. Everything - Cell Phone etc. in the floor ..
Got the mileage in today and I just did my overkill third and final breakin oil change in the first 500 miles tonight .. Turning the boost up on the next drive ..
futurevr4man
04-17-2013, 02:17 PM
this thread needs more pictures and ESPECIALLY videos! i guarantee you have a cell phone capable of making some, so lets see it!
Lugnut
04-17-2013, 04:03 PM
O.K. Guys .. Not trying to come off anal on the posts but Im just giving you the 411 on whats happening here with car ..
Exxon 93 .. 70 degrees outside .. The car is up to 18 tipping into 19 .. Spinning 2nd now and getting seriously quick .. Registering zero knock .. Added another click on the Arc2 high .. Fuel is 11-3 area .. After 5-6 runs I got out of it as its just so many gauges to watch at one time as well as drive so .. As it stands weather permitting JasonY and I are gonna go out this evening and turn the car up to see what we can get out of it .. Based on the above info Im guessing at least 21 on pump ..
Getting a on the street outside the car video hasnt been an option yet, but I will work on that and as soon as I get the op I will get one .. In the mean time
A few pics .. IPS anodized (sleeper) frontmount .. The engine bay including true GTO fuse box covers ..
http://i230.photobucket.com/albums/ee213/tazz_375/037.jpg
http://i230.photobucket.com/albums/ee213/tazz_375/035.jpg
http://i230.photobucket.com/albums/ee213/tazz_375/039.jpg
http://i230.photobucket.com/albums/ee213/tazz_375/041.jpg
http://i230.photobucket.com/albums/ee213/tazz_375/003.jpg
Chris@Rvengeperformance
04-17-2013, 04:18 PM
nice to hear
Blackmount
04-17-2013, 04:25 PM
Awesome! U should do a few VD logs :D great aid for tuning imo.
Your engine bay looks very clean. I always prefer black piping and couplers... at first glance it almost looks stock!
AdamVR4
04-17-2013, 04:35 PM
No rush, lugnut. Enjoy the car :)
JasonY
04-17-2013, 08:02 PM
Hotwired Wally 255 maxed out at like 15psi..lol She's moving a bit of air:) Wally 400 installed. Off to do some tuning with a proper pump:)
Jason
SnakeSkinner
04-17-2013, 08:14 PM
Hotwired Wally 255 maxed out at like 15psi..lol She's moving a bit of air:) Wally 400 installed. Off to do some tuning with a proper pump:)
Jason
haha, I new it, when Tod told me he had to keep adding turns on the high on the ARC-2 as he added boost I new there was a fuel supply problem.
Went and watched the fuel gauge I take it during a run?
anyonebutme
04-17-2013, 08:27 PM
I do like this
Jay will have some interesting things to say about it as well, I'm sure - never felt we heard enough from you guys the first time around with the 750s. :)
Any dyno-time scheduled?
A high-water mark for pump, maybe? :wink:
JasonY
04-17-2013, 09:50 PM
Stock regulator is dead. Rising 1/2:1 psi, wally 400 killed it..lol
Will address. Runs like a total asshole to 5k then we gotta back out..haha
Jason
Lugnut
04-17-2013, 10:54 PM
Just put Chris Hill on the spot .. AEM FPR ordered .. So .. tick tock tick tock ..
Lugnut
04-17-2013, 11:00 PM
Jay will have some interesting things to say about it as well, I'm sure - never felt we heard enough from you guys the first time around with the 750s. :)
Any dyno-time scheduled?
A high-water mark for pump, maybe? :wink:
I have talked to Ray about getting on the dyno but havent set a date .. Looks like its gonna be a minute though as I have to leave the state early next week till mid May :(
J. Fast
04-17-2013, 11:55 PM
I like this! Engine bay looks great. Heads looked dope1
I have talked to Ray about getting on the dyno but havent set a date .. Looks like its gonna be a minute though as I have to leave the state early next week till mid May :(
I'm hooked - I'll wait. :D
AdamVR4
04-18-2013, 02:08 PM
Hotwired Wally 255 maxed out at like 15psi..lol She's moving a bit of air:) Wally 400 installed. Off to do some tuning with a proper pump:)
Jason
So that means you're around 450 AWHP @ 15 psi? I can't quite recall where the hotwired 255 is maxed, but I'm pretty sure it's below 500 on gasoline. Regardless, that's a very efficient TD04 set-up.
TurboSinceBirth
04-18-2013, 03:59 PM
So that means you're around 450 AWHP @ 15 psi? I can't quite recall where the hotwired 255 is maxed, but I'm pretty sure it's below 500 on gasoline. Regardless, that's a very efficient TD04 set-up.
3SX would max one on their dyno around 525AWHP. I'm almost surprised you guys ruined the stock FPR. I guess Ray, myself, and a few others on ethanol using the stock FPR have to have the increased flow for every bit of 25-30 psi plus we've tuned it out at idle to keep the idle AFRs from going rich. Maybe your FPR was old to begin with. An AFPR won't be a bad idea though.
JasonY
04-18-2013, 06:49 PM
As soon as the 400 went in, shot to 70psi at idle...bye bye w/e life was left in the fpr. Hasn't worked for shit since. Can't tune the car with a 70psi base pressure..lol
Jason
AdamVR4
04-18-2013, 07:03 PM
Is the stock return line enough for the 400? My pair of 255's run in parallel (so considerably less than 510 lph) with a stock return line cause 50 psi base even if the AFPR is completely open.
Chris@Rvengeperformance
04-18-2013, 07:27 PM
As soon as the 400 went in, shot to 70psi at idle...bye bye w/e life was left in the fpr. Hasn't worked for shit since. Can't tune the car with a 70psi base pressure..lol
Jason
That's odd. been running the stock fpr on the walbro 400 e85 hotwired for a couple months now. my fpr is new
JRink
04-18-2013, 09:45 PM
3.5L + 16Gs Steve only made 525AWHP on a 3.5L + 16Gs with pump gas only which was comparable to Ray's built 3.0L DR Stage III heads, cams, and DR-750s at 525AWHP on pump. However, on Ray's old chameleon car he sold to a guy that put a 3.5L + 16Gs in he made 665AWHP and 748AWTQ. That's definitely impressive. It will be interesting to see how much tq the 3.5L will let the DR-750s make.
I think Ray's old chameleon car was dyno'd on e85 with those numbers, with outstanding results. But the pump gas numbers with 3.5L/16Gs are still very good -- I made 600awhp on that setup with 93-pump (no meth) about 5 years ago. Was a crazy torque monster too, 740awtq (700+ @ 4k rpm) with 3.5L/16Gs on race gas. It really is a wicked setup. Felt like I was driving a V8. I'm surprised more people haven't gone down that route, especially with the Ray/Merkel 3.4L Stroker which is practically a no-brainer if you're prepping/rebuilding a motor these days.
JasonY
04-18-2013, 09:51 PM
Is the stock return line enough for the 400? My pair of 255's run in parallel (so considerably less than 510 lph) with a stock return line cause 50 psi base even if the AFPR is completely open.
Yet to be determined, but I havnt ruled that out as being a possibility either.
That's odd. been running the stock fpr on the walbro 400 e85 hotwired for a couple months now. my fpr is new
This one is the OG one from 97. A new one is around 70 bucks so we're gonna see if a AFPR can get the pressure to a more reasonable level and as Adam mentioned above, see if the stock return can handle that much pump. We really dont want to change from the stock fuel lines since they are so reliable/trouble free vs aftermarket.
Jason
Chris@Rvengeperformance
04-18-2013, 09:54 PM
Yeah, I hear you. I had the aem fpr and it fits great, but I didn't like the pressure drop off on key off, so I went new oem.
Greg E
04-18-2013, 10:33 PM
Yeah, I hear you. I had the aem fpr and it fits great, but I didn't like the pressure drop off on key off, so I went new oem.
Fuel pump on clutch chrome mod.
TurboSinceBirth
04-18-2013, 10:42 PM
That's odd. been running the stock fpr on the walbro 400 e85 hotwired for a couple months now. my fpr is new
Same here. I've ran mine for about 5-6 months. I'm pretty sure mine is the original one in the car. I did progressively go from a Walbro 255 to Aeromotive Stealth 340 to Walbro 485 as I kept running out of fuel so the initial turn key wasn't as big of a shock with the tune not being too far off at idle. If my base pressure was through the roof I wouldn't ever be able to lean out the car on ethanol. I can peg the AEM wideband past 20:1 AFR at idle with the walbro and 1000cc injectors but I definitely don't run it that way. Lol. All I can think of is that the FPR was probably worn out and going to fail anyways.
Chris@Rvengeperformance
04-18-2013, 10:48 PM
Fuel pump on clutch chrome mod.
yeah if I did it again I'd use that, it wasn't done yet when I switched fprs.
JasonY
04-20-2013, 04:15 PM
Pressure still stuck high. Anything we're missing other than the obvious fuel return line limit? Might buy some bigger line to run off the afpr and bypass the stock return just for diagnostic purposes.
Jason
TurboSinceBirth
04-20-2013, 05:26 PM
Which AFPR are you using and are you sure there isn't too small of an orfice installed in it?
anyonebutme
04-20-2013, 06:18 PM
return line plugged?
run a line into a fuel can from the return port......does it drop back down?
Tigchamp
04-20-2013, 06:29 PM
The usual fix is to run a bigger feed and then use the old feed as a return. or alternatively if you are thinking of doing the rear steer delete use the lines from the front to the rear rack they are quite large bore and steel
JasonY
04-20-2013, 07:29 PM
Got the pressure sorted out. Had the smallest orifice in the regulator, put in the big one, 45psi base now.
Still knocks at 5k-5500 like a fukin whore. Arc is maxed out. Need my compressor from work, boost leak suspected. If not, bonfire.
Jason
wingnut
04-20-2013, 07:45 PM
...boost leak suspected. If not, bonfire.
lol...saved for future use :D
SnakeSkinner
04-20-2013, 09:19 PM
Got the pressure sorted out. Had the smallest orifice in the regulator, put in the big one, 45psi base now.
Still knocks at 5k-5500 like a fukin whore. Arc is maxed out. Need my compressor from work, boost leak suspected. If not, bonfire.
Jason
Is the fuel pressure correctly matching 1 to 1 with boost? IE 45psi base, 55psi at 10 psi of boost, 60psi at 15psi of boost ect?
When you say ARC-2 is "maxed out" what do you mean?
JasonY
04-20-2013, 09:25 PM
Yes, working 1:1 now. Cant find a balance between high/low. We have the high maxed out and not enough fuel up top, still leans out in the middle since to keep the idle at all, needs the low fairly lean, around zero or +1, accel at +3 i think and its not enough down low causing it to come up short up top. Cant seem to get it balanced to where it will idle, fuel enough down low but have enough fuel up top. We got a few clean pulls, but had so much fuel it wouldnt idle, at all. And was like 10:1 up top, probably looked like a diesel lol.
Fixed all suspected leaks and will reassess tomorrow after any/all leaks fixed.
Last time we had this problem with the ARC is was a leak. So we shall see. But even at 14psi it'll pull smooth/clean to 5k rpms nice flat AFR 11:1-3 and around 5k...gotta lift since it'll instantly/predictably jump into the teens on knock.
Jason
futurevr4man
04-21-2013, 01:40 AM
i know there is a flashable sittin in the basement. just sayin...
i dont get the bonfire reference?
Greg E
04-21-2013, 01:41 AM
Yes, working 1:1 now. Cant find a balance between high/low. We have the high maxed out and not enough fuel up top, still leans out in the middle since to keep the idle at all, needs the low fairly lean, around zero or +1, accel at +3 i think and its not enough down low causing it to come up short up top. Cant seem to get it balanced to where it will idle, fuel enough down low but have enough fuel up top. We got a few clean pulls, but had so much fuel it wouldnt idle, at all. And was like 10:1 up top, probably looked like a diesel lol.
Fixed all suspected leaks and will reassess tomorrow after any/all leaks fixed.
Last time we had this problem with the ARC is was a leak. So we shall see. But even at 14psi it'll pull smooth/clean to 5k rpms nice flat AFR 11:1-3 and around 5k...gotta lift since it'll instantly/predictably jump into the teens on knock.
Jason
Pump gas sucks.
Install the 98 ECU and set the injector scalings. Get a decent tune with the ARC. Tweak the timing with ECUFlash.
anyonebutme
04-21-2013, 01:50 AM
i dont get the bonfire reference?
Light the F*CKING car on FIRE!!!!!!!!!!!!!!
SnakeSkinner
04-21-2013, 02:55 PM
Yes, working 1:1 now. Cant find a balance between high/low. We have the high maxed out and not enough fuel up top, still leans out in the middle since to keep the idle at all, needs the low fairly lean, around zero or +1, accel at +3 i think and its not enough down low causing it to come up short up top. Cant seem to get it balanced to where it will idle, fuel enough down low but have enough fuel up top. We got a few clean pulls, but had so much fuel it wouldnt idle, at all. And was like 10:1 up top, probably looked like a diesel lol.
Fixed all suspected leaks and will reassess tomorrow after any/all leaks fixed.
Last time we had this problem with the ARC is was a leak. So we shall see. But even at 14psi it'll pull smooth/clean to 5k rpms nice flat AFR 11:1-3 and around 5k...gotta lift since it'll instantly/predictably jump into the teens on knock.
Jason
Very strange, make sure to check your wiring. Also maby spray some MAS cleaner threw the MAS it may be all oiled up.
Lugnut
04-25-2013, 01:16 AM
Sorry I havent been online to make a post but I've really had nothing great to tell .. Been very busy day in and out working on the car adding the pump and testing and then the FPR and testing and then going through the system tightening up boost leaks and testing and all to no avail ..
Unfortunately I ran out of time with the car and had to jump a plane and fly down to Texas for 3 or so weeks so there will be no real update for say .. But .. As if on cue now that Im way the hell over here on the other side of the country I believe I have figured out the problem .. The one thing I totally overlooked was that when we added the AEM Fuel Pressure gauge to the system we plumbed it with an autometer 2276 Banjo on the filter and I'm pretty sure that is the restrictive problem .. So .. Go ahead .. Flame away !!!
CoopKill
04-25-2013, 08:30 PM
http://www.torcavettes.com/tech/fire/Extinguisher_Lady.gif
Lugnut
05-11-2013, 05:01 AM
Updated the mod list on page 1.
Heading back to the East Coast sometime this upcoming week. Got a new fuel feed setup to install and with any luck should have the coilovers and KDW's on the car as well.
Planning to go down to the Ocean City Spring Cruise this upcoming weekend (16th-20th) and get some playtime in with the car. This meet is in its 23rd year and it features roughly 3000 modded street cars and dream machines of every type in the U.S. It is laid out on a triple lane 150 block light to light cruise strip, And its definitely one of the absolute best times to be had anywhere in the country for any type of car enthusiast of any sort. Car show, auction, cruising, and parking lots everywhere overflowing with cars. In the day the scene is crazy enough, but once the sun goes down the HP gets insane on the street. Light to light drag races everywhere you look and the smell of race gas and burnt rubber is a constant. With the tradition instilled, overall cops have always been pretty lenient til 10p.m. or so.
I cannot encourage anyone in the area enough to make a trip down. If you get one vaca a year and your into cars. This is the place for you !!! And before you say it. I have absolutely NO idea why ECG isnt held on this particular weekend. Make no sense to me !!!
The show info in the below link
Special Event Productions, Inc. (http://www.specialeventpro.com/cruisin.php)
The strip. Runs North and South and just loops around.
http://www.virginia123.com/maryland-easternshore/AIMG_1593ocean-city-md-07-2012.jpg
At present it looks pretty solid like Monochrome and JasonY will be on scene for the weekend so taking nothing off the table we should be able to make some headway with the car if we can stay outta Ocean City for a few hours. If all goes well and according to plan we should even see a tank or two of 100.
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.