PDA

View Full Version : Couple Virtual dyno charts from todays outing



Ninja Performance
04-06-2013, 06:51 PM
Couple virtual dyno pulls on the car today. Couple new things so wanted to see what she had this race season.

On Trevor's recommendation I tried out the Champion race plugs. They have no strap, so no gap to worry about. All I can say is WOW. I overboosted (36-37psi) and my AEM only has 3.5 bar map so 35.12 or above goes into fuel cut.

New crankcase breather system to relieve crankcase of pressure. And a little tinkering with the timing map.

I also found the adjustable cam heard were all -1 to -1.5 degrees off when at 0 so I reset 0 and set them to the correct -3 +1. Which would also explain some power increase.

Knock is WAY down, it is running much quieter now. Pulled smoother and stronger. I thought it felt better. Then I did the Virtual dyno graphs. Wholly Bejeebus.

Those who don't know, I run:
3.0L Stock heads and cams
95% Ethanol 5% Methanol
I probably am a little light on the car weight on the graphs, but wanted to error on light side rather than heavy so the numbers would be more realistic.

825AWHP 798TQ @30psi
914AWHP 881TQ @36psi

https://sphotos-a.xx.fbcdn.net/hphotos-frc1/891918_551480188208166_2141956481_o.jpg

-Chris

futurevr4man
04-06-2013, 07:41 PM
can you go into more detail (with pictures please) on your crank case vent setup please?! i am wanting to get a new setup for my car, but havent come up with anything good yet.

great results as always chris. what plugs specifically did you use? my NGK coppers are doin pretty well for me, but i am always open to other options!

keo92stealth
04-06-2013, 07:58 PM
Flippin aswome !!! Can't wait to see what this thing does this season !!

Ninja Performance
04-06-2013, 08:29 PM
I thought the ngk coppers I was running, non projected 8, were great. Trevor tested these Champions out and said they were great for high HP and ethanol. Sure enough, more power, smoother, and my Knock volts and raw are both MUCH lower and smoother.

Champion Spark Plug C53VC

-CHris

futurevr4man
04-06-2013, 09:23 PM
thanks chris!

again, if you wouldnt mind, i would love to see your crankcase setup too!

Ninja Performance
04-06-2013, 09:31 PM
thanks chris!

again, if you wouldnt mind, i would love to see your crankcase setup too!

both drivers side go to open empty oil bottles
pass side rear and front (with PCV delete fitting Ninja Performance PCV Valve Delete Fitting (NPPCVD) - Ninja Performance - Affordable Performance (http://www.ninjaperformance.com/ninja-performance-pcv-valve-delete-fitting-p-21815.html) ) go to a vented catch can.
Then I have a -10AN fitting on the pass side front cover in the baffled area with -10AN SS braid going to a catch can with two large filters for venting.

-Chris

futurevr4man
04-06-2013, 09:35 PM
so are you not pulling a vacuum at idle at all?

Ninja Performance
04-06-2013, 09:54 PM
No i am not.

-Chris

futurevr4man
04-06-2013, 09:58 PM
am i incorrect in the thought that the car should be pulling some vacuum through the crank cases at idle? i thought it was supposed to help the seals

Roybatty
04-06-2013, 10:15 PM
Wow. Thanks for sharing. Will have to check out the Champions.

Future; gleaning from the numerous pcv/catch can/krank vent threads, yes; vacuum helps @ idle, iirc depends on car use, ie dd verses track.

Revel in your time

wingnut
04-06-2013, 11:07 PM
nice numbers man...stock 3.0, but would you be in the mood to share you mod list, or is that top secret :D

Blackmount
04-06-2013, 11:12 PM
Again, great numbers. I love playing with VD, tho many people do not take it seriously which I think is kinda dumb...

any more thoughts on those C53VC plugs? how would they fair on a mostly stock/bpu car vs the NGK Coppers do you think?

futurevr4man
04-06-2013, 11:32 PM
man those plugs are interesting. with the way they are designed, the flame front is beginning higher in the cylinder. im trying to think about how that would affect power... very interesting is all i can say

familyMAN
04-07-2013, 12:08 AM
Good stuff Chris.

I do think it's a little inflated though. You are making the same tq at 2500-3000 rpms as my 10:1 3.5 (verified by dyno). and I am already making 6psi by 3000 rpm.

Also since you still have some spike, waviness with smoothing on 2 (especially red lines), leads me to think that as well. I found that the spiked data points you are trying to smooth out would inflate the numbers so I didn't like to use any graphs that needed more than "1" smoothing for comparison. You're double the hp than I was though, so not sure how that affects the data.

Hopefully you prove me wrong at the track since it sounds like you are getting ready (NTLS thread) :D

Ninja Performance
04-07-2013, 12:21 AM
Good stuff Chris.

I do think it's a little inflated though. You are making the same tq at 2500-3000 rpms as my 10:1 3.5 (verified by dyno). and I am already making 6psi by 3000 rpm.

Also since you still have some spike, waviness with smoothing on 2 (especially red lines), leads me to think that as well. I found that the spiked data points you are trying to smooth out would inflate the numbers so I didn't like to use any graphs that needed more than "1" smoothing for comparison. You're double the hp than I was though, so not sure how that affects the data.

Hopefully you prove me wrong at the track since it sounds like you are getting ready (NTLS thread) :D

Remember, I run on pure alcohol. 95% ethanol 5% methanol.
During my vast testing, I found that my setup with E95M5 and DR1000 size turbos ran almost identical numbers to a 3.5 DR1000 car on race gas (or pump up until it needed race gas). Lots of dyno testing proved that. I pretty much have said since then that E95M5 makes a 3.0 put out 3.5 power. So it does not surprise me that I make the same Tq as you in low RPM range. I also run a god awful amount of fuel, 45-50% more volume than a gas setup.

With the old tune, cam setup, spark plugs, and a few pounds less boost I was running 115MPH 1/8 and 144MPH 1/4s.

-Chris

familyMAN
04-07-2013, 01:15 AM
I pretty much have said since then that E95M5 makes a 3.0 put out 3.5 power. So it does not surprise me that I make the same Tq as you in low RPM range. I also run a god awful amount of fuel, 45-50% more volume than a gas setup.

-Chris

My data was with e85, not gas. I wasn't saying its completely off base, just saying based on the 2500-3000 rpm data (and 2 smoothing needed) IMHO it could be slightly high, but I'm just a guy with a blown up engine, so take my opinion for what it's worth...right now, not much:D There may not even be enough acceleration data from the initial hit for VD to be accurate for the first 500 rpm??

You probably have some old logs from the same tune you ran 835 on dyno. For comparison, maybe try one of those in virtual dyno?

Hell of a setup and you are closing in on T4's old numbers with less mods and less turbo if I recall correctly.

Edit: On the 825 run, were you wanting to run 13:1? Experimentation?

mehrshadvr4
04-07-2013, 04:01 AM
Do you have hks twin power?

Ninja Performance
04-07-2013, 08:51 AM
My data was with e85, not gas. I wasn't saying its completely off base, just saying based on the 2500-3000 rpm data (and 2 smoothing needed) IMHO it could be slightly high, but I'm just a guy with a blown up engine, so take my opinion for what it's worth...right now, not much:D There may not even be enough acceleration data from the initial hit for VD to be accurate for the first 500 rpm??

You probably have some old logs from the same tune you ran 835 on dyno. For comparison, maybe try one of those in virtual dyno?

Hell of a setup and you are closing in on T4's old numbers with less mods and less turbo if I recall correctly.

Edit: On the 825 run, were you wanting to run 13:1? Experimentation?

I am sure VD is off from an actual dyno, but then again, all dyno's are different as well. And VD is only as good as the numbers put in and the flat road you use. I have a flat long road in the country I use and input the right car data and weight to get as close as possible. Same road and another AEM car with EVOIIIs and I struggled to get 480HP out of it at 18-20psi with Meth injection, so I know it's pretty close.

Many Many others have tested back to back dyno and VD and found it to be pretty close. As far as smoothing 2, that is just where mine is set so I use it, never set it to 1 to see what would happen. Higher numbers I suppose? Maybe 2 would cover up some wheelspin?

As for the arf, I normally don't run that low boost and the fuel map isn't as rich as it should be. It was not on purpose.

I didn't log all the data points needed for VD back in the day so I can't import those old logs into VD to see what it looked like. Also not sure I ever ran a 2000-redline pull on the street before since I wasn't trying to get VD info, so that log never happened.

I know how my car ran before all the mods, and now it is smoother and pulls slightly harder, so a jump from 835AWHP to 900 wouldn't be far fetched to me, my butt tells me it gained power. Maybe not 900 but much higher than 835.

All in all, it has more power, who knows how much, time to take it to the track. I did however run 2 more pounds of boost so there is some of the power there, then there are the cam gear settings, and the spark plugs burning more of the charge.

-Chris

Ninja Performance
04-07-2013, 08:54 AM
Do you have hks twin power?

Yes. Mods Here:
Ninja Performance - Your Affordable Performance Parts Store (http://www.ninjaperformance.com/about_us.php)

-Chris

AdamVR4
04-07-2013, 11:15 AM
Stock cams... wow. Ever thought about seeing what it would do on c16? Obviously less but still 700+?

Ninja Performance
04-07-2013, 11:38 AM
Stock cams... wow. Ever thought about seeing what it would do on c16? Obviously less but still 700+?

Many others, including myself, have pushed stock cams and heads on a 3.0 and I think the wall was around 600AWHp 650 TOPS depending on dnyo.

But that is due to the air flow stock cams and heads can flow. There is a limit. But I sneak in MORE air via a HIGHLY oxygenated fuel. You can see however that past 6250 power starts to take a dive due to this. Turbos are still pumping out the same if not even higher boost, (probably higher psi due to restriction increasing at higher RPM) but power is dropping. All due to the heads and cams running out.

I am almost done with pushing this 3.0L stock head/cam setup. Have some track visits to do to complete it.

-Chris

familyMAN
04-07-2013, 11:38 AM
Stock cams... wow.

And basically stock heads, CXracing intercooler. About as simple td05 setup as can be done. Amazing results.

E95 is magic juice!

Good cams and heads will be interesting.

Ninja Performance
04-07-2013, 12:04 PM
I do have hi rev springs in the heads as I did a lot of testing with cams, then sold them and went back to stock cams to get some bottom end back. And to see how far I could push stock heads and cams.

-Chris

Blackmount
04-07-2013, 12:09 PM
Still never answered my q about the spark plugs
Christopher :)

Ninja Performance
04-07-2013, 12:10 PM
I always have it set to smoothing=2 as default, SO here it is with smoothing=1

http://www.ninjaperformance.com/images/NinjaVR42013smooth1.jpg

-Chris

Ninja Performance
04-07-2013, 12:16 PM
Can't see the Champions hurting a low power car, but really don't think they would help either. They are really for high HP race applications.

-Chris

Blackmount
04-07-2013, 12:25 PM
Thanks. Eliminates the needs of indexing tho im sure no one does that these days.

Trevor
04-07-2013, 01:06 PM
Even with a twinpower on a brand new OEM ignition (PTU, coils, and wires) I had breakup with E85 at 32+ psi. With Denso Iridiums (which I'm a huge fan of) it was horrible. Went to the non projected plugs with a tight gap and it improved but my logs still showed significant back steps in RPM at peak torque (IE peak cylinder pressure). Went to flat electrode plugs like these:
http://www.sparkplugssource.com/images/5719.jpg
...and it further improved but the $10 a piece plugs I was running were discontinued and the only plugs available now of that construction are ~$34 a piece which is F'in ridiculous. Ended up doing some research on plug attributes/characteristics and settled on the Champions. I'm no fan of the brand but they work great. They are one of if not THE only option out there with an off the wall contruct. Maybe if we continue to keep a demand on the part number it won't go away.

Big take aways of the surface discharge plugs are that they're very resistant to blow out and fouling. They're not rotary engine specific either. F1 used to use em back in the day.

http://ecx.images-amazon.com/images/I/51U64QYwJXL._SL500_AA300_.jpg

Blackmount
04-07-2013, 01:59 PM
I will be keeping these in mind down the road. Chris what is ur bottom end like?

Ninja Performance
04-07-2013, 03:27 PM
Thanks. Eliminates the needs of indexing tho im sure no one does that these days.

Indexing was for plugs that were to the side, in a Hemi head setup, like ours, indexing makes no difference.

-Chris

mehrshadvr4
04-07-2013, 04:13 PM
Since you are running e95 you don't even need to run intercooler any more. run the charge pipes to the TB and enjoy The boost respond.you might even gain some power because your turbos will flow more per psi. :D

R/T93
04-07-2013, 05:25 PM
Since you are running e95 you don't even need to run intercooler any more. run the charge pipes to the TB and enjoy The boost respond.you might even gain some power because your turbos will flow more per psi. :D

A friend with a 450 horse 240 does that, his intake is about 2 ft long. Injects e85 into the chargepipe, too.

From the phone.

Ninja Performance
04-07-2013, 05:37 PM
I will be keeping these in mind down the road. Chris what is ur bottom end like?

Detail
Ninja Performance - Your Affordable Performance Parts Store (http://www.ninjaperformance.com/about_us.php)

General, 4 bolt 3.0L stock crank, BC rods, Wiseco coated skirt pistons with Ninja Performance H13 tool steel .200" wall pins
Stock heads and cams
Stock TBG and plenums (upper,lower)
stock oil pump, water pump
Ninja Performance Solid Timing Kit

-Chris

vr4tune
04-07-2013, 06:49 PM
Knock is WAY down, it is running much quieter now. Pulled smoother and stronger. I thought it felt better. Then I did the Virtual dyno graphs. Wholly Bejeebus.

Those who don't know, I run:
3.0L Stock heads and cams

-Chris

1st, do you think the drop in knock could partially be from the cam gear timing being corrected.


2nd, just for clarity your heads are port matched right? As well well as gasket matched upper and lower intake plenum?

familyMAN
04-07-2013, 07:44 PM
I always have it set to smoothing=2 as default, SO here it is with smoothing=1

http://www.ninjaperformance.com/images/NinjaVR42013smooth1.jpg

-Chris

As I commented on other site, smoothing on 1 looks good. Not as spikey/wavy as I expected, since I incorrectly assumed you were using "2" to smooth the graph. Comparing the low end to your 835awhp graph....

http://www.ninjaperformance.com/VR4/835AWHP.jpg

You're making 50-80 more awtq below 3500rpm now, vs your 835awhp graph. Maybe it's the road, maybe its VD, maybe your tune sub-boost is that much better, your adjusted cam timing, etc. I love VD and just want to see what your thoughts are. Trevor had some trouble with his readings, but Leonel (if I recall) at 900ish hp also, was spot on to his dyno. Mine was spot on as well, granted only 400/475

I hope that the 3S community can discuss these results so that everyone can be as comfortable as the EVO guys using VD, as a way to compare mod and setup changes/results. I wouldn't have even brought it up if it wasn't for the sub-boost data and genuinely want your results to be valid which will add more confidence and validity to all VD charts.


Since you are running e95 you don't even need to run intercooler any more. run the charge pipes to the TB and enjoy The boost respond.you might even gain some power because your turbos will flow more per psi. :D

That would be cool to see on a 3S:)

J. Fast
04-07-2013, 08:11 PM
I too took Trevors advice on the spark plugs awhile back. 40hrs of dyno time and 10k miles and no signs if weakening. FYI the gap on those is about 40 thou. I'm in the mid 700's at 30psi on billet 20g's with a DLI on E85 with a 3.1 bottom on stock heads and cams also.

Good stuff Ninja!

Also, I would like to add I only recc champion spark plugs. They're great plugs and only two bucks a piece. Stealth316 has a cross reference for all plugs. Props to Trevor for plug rec a year ago!

futurevr4man
04-07-2013, 08:22 PM
where are you all getting your plugs from?

Trevor
04-07-2013, 08:29 PM
Trevor had some trouble with his readings...
I figured out my issue. Once I got the RPM sample rate out the stratosphere and down to <20Hz the charts are much more realistic and smooth. VD doesn't like 250Hz worth of RPM data.

Props to Trevor for plug rec a year ago!
Glad I could help!

familyMAN
04-07-2013, 08:33 PM
^Good to know!

Looks like I'm sold on these plugs too and will be picking up a set for the rebuild.

Edit: just picked up a set from Ebay/summitracing at Chris's suggestion. Only $34.65 shipped!

J. Fast
04-07-2013, 08:40 PM
where are you all getting your plugs from?
Pep Boys and Advanced Auto has nearly every Champion spark plug referenced in 316 as well as the plugs being discussed in stock.

futurevr4man
04-07-2013, 08:50 PM
Pep Boys and Advanced Auto has nearly every Champion spark plug referenced in 316 as well as the plugs being discussed in stock.

the places around here suck balls. i called autozone, advanced, and napa and only autozone said they could get them for me at a mere $27 a piece! what a deal! i am gonna get some from summit. i am really liking the idea of these plugs and have been reading up on this style

J. Fast
04-07-2013, 11:07 PM
FYI on these plugs guys... The Champion Manufacturer part number on the box is Champion Spark Plug # 694 or CPN-694. You will not be able to find them at local stores using a C53VC model number.

You should stock them Ninja, they're a legit plug. They retail for $4.25 each, in store no discount, in Denver.

AdamVR4
04-08-2013, 01:31 AM
I do have hi rev springs in the heads as I did a lot of testing with cams, then sold them and went back to stock cams to get some bottom end back. And to see how far I could push stock heads and cams.

-Chris


Do you know the brand of high rev springs? Have you encountered any springs you wouldn't recommend? It's hard to find anyone with an opinion on our aftermarket valve springs. They all seem to work.

Ninja Performance
04-08-2013, 02:14 AM
Little more information on these two runs.

I live in the country, so long flat sections of country road are available to me.

There was no wind this day. About 75F out.

The two runs were done within 2 minutes of each other. I turned my Profec to Lo and ran the first run, turned around, set the Profec to Hi and did the second run.

I would suspect the slightly faster spool is due to me wrapping the front manifold and rear turbine housing in heat wrap and the hotter turbos since they were just ran. Heat means expansion/energy.

-Chris

Ninja Performance
04-08-2013, 02:19 AM
1st, do you think the drop in knock could partially be from the cam gear timing being corrected.


2nd, just for clarity your heads are port matched right? As well well as gasket matched upper and lower intake plenum?

I think my "knock" in my aem logs which would make a grown man cry (think 3.5-4 volts) that is now 2.0 and under at 38psi! may be due to not getting a full burn. My bearings always look brand new and plugs never have detonation flakes on them. But now with these plugs, correctly adjusted cam gears etc the knock raw and knock volts is way low.

Yes, I did (3 years ago) gasket match my lower plenum, cylinder intake and upper plenum. But JUST gasket match, No work in the ports.

-Chris

Ninja Performance
04-08-2013, 02:22 AM
I think I found a source for getting the Champion C53VC plugs through one of my vendors, we will sell them as cheap or cheaper than summit or anywhere else I have found. Give me a few days.

-Chris

vr4tune
04-08-2013, 02:23 AM
I think my "knock" in my aem logs which would make a grown man cry (think 3.5-4 volts) that is now 2.0 and under at 38psi! may be due to not getting a full burn. My bearings always look brand new and plugs never have detonation flakes on them. But now with these plugs, correctly adjusted cam gears etc the knock raw and knock volts is way low.

Yes, I did (3 years ago) gasket match my lower plenum, cylinder intake and upper plenum. But JUST gasket match, No work in the ports.

-Chris
That's awesome Chris, you rock and I love what you do for this community! I will be ordering some stuff from you soon!

Ninja Performance
04-08-2013, 10:36 AM
We should have the plugs in stock soon, cheaper than anywhere else if my vendor comes thru.

-Chris

Ninja Performance
04-08-2013, 10:38 AM
Adam,

I have the Supertech, not the cheapest but I have also heard bad things about the BCs not holding their spring pressure over time.

Supertech Hi Rev Spring/Retainer Kit 91-99 3000GT Stealth 6G72 DOHC (SPRK-M1007S3000) - Ninja (http://www.ninjaperformance.com/supertech-rev-springretainer-kit-3000gt-stealth-6g72-dohc-p-2126.html)

-Chris

AdamVR4
04-08-2013, 12:59 PM
Adam,

I have the Supertech, not the cheapest but I have also heard bad things about the BCs not holding their spring pressure over time.

Supertech Hi Rev Spring/Retainer Kit 91-99 3000GT Stealth 6G72 DOHC (SPRK-M1007S3000) - Ninja (http://www.ninjaperformance.com/supertech-rev-springretainer-kit-3000gt-stealth-6g72-dohc-p-2126.html)

-Chris


Thanks and great price. Looks like I'll be ordering these from you. I know you use a solid tensioner, but have you ever tried to use these on a stock tensioner? I'm going to tighten it so that the plunger is bottomed out, but any tips on that front are appreciated.

familyMAN
04-08-2013, 01:39 PM
I know I'm talking to myself, but here is a good post on evolution.net on using VD. Really good, simple info for anyone wanting to use it. How to use Virtual Dyno Properly - evolutionm.net (http://forums.evolutionm.net/evo-dyno-tuning-results/619146-how-use-virtual-dyno-properly.html)

Specifically...
Using Smoothing to Verify the Accuracy of the Logs

The smoothing function in VD can be used to determine how accurate your power output is based on the consistency of power from Smoothing 1 to Max. A good rule of thumb is, if your power drops less then 12-15WHP from smoothing 1 to Max, then the run is accurate and will most likely make very similar numbers on a real Dynojet dyno, usually with 0-3%. If your power drops off 20-25WHP or more from smoothing 1 to Max, you should be aware that the VD chart may not be accurate and your power could be off 5%, if not more, from a real Dynojet dyno.



Thanks and great price. Looks like I'll be ordering these from you. I know you use a solid tensioner, but have you ever tried to use these on a stock tensioner? I'm going to tighten it so that the plunger is bottomed out, but any tips on that front are appreciated.

My 3.0 had a stock tensioner with DR street cams and high rev kit, regular belt (non-kevlar). No issues holding timing with it's limited run time. Hit 8k+ a couple times in first and second. I believe it was set a little tighter than stock, but definitely not bottomed out.

Ninja Performance
04-08-2013, 01:56 PM
Thanks and great price. Looks like I'll be ordering these from you. I know you use a solid tensioner, but have you ever tried to use these on a stock tensioner? I'm going to tighten it so that the plunger is bottomed out, but any tips on that front are appreciated.


I put these in a while ago with the stock Mitsu Hydro tensioner and it has been beat on and to the rack that way with no issues. So I would say you will be fine.

-Chris

oohnoo
04-08-2013, 09:57 PM
Trevor...might have already listed it but you got a part number for those plugs?


Even with a twinpower on a brand new OEM ignition (PTU, coils, and wires) I had breakup with E85 at 32+ psi. With Denso Iridiums (which I'm a huge fan of) it was horrible. Went to the non projected plugs with a tight gap and it improved but my logs still showed significant back steps in RPM at peak torque (IE peak cylinder pressure). Went to flat electrode plugs like these:
http://www.sparkplugssource.com/images/5719.jpg
...and it further improved but the $10 a piece plugs I was running were discontinued and the only plugs available now of that construction are ~$34 a piece which is F'in ridiculous. Ended up doing some research on plug attributes/characteristics and settled on the Champions. I'm no fan of the brand but they work great. They are one of if not THE only option out there with an off the wall contruct. Maybe if we continue to keep a demand on the part number it won't go away.

Big take aways of the surface discharge plugs are that they're very resistant to blow out and fouling. They're not rotary engine specific either. F1 used to use em back in the day.

http://ecx.images-amazon.com/images/I/51U64QYwJXL._SL500_AA300_.jpg

wingnut
04-08-2013, 10:26 PM
Trevor...might have already listed it but you got a part number for those plugs?



Hmmm...post 42???



FYI on these plugs guys... The Champion Manufacturer part number on the box is Champion Spark Plug # 694 or CPN-694. You will not be able to find them at local stores using a C53VC model number.

mehrshadvr4
04-09-2013, 07:22 AM
Adam,

I have the Supertech, not the cheapest but I have also heard bad things about the BCs not holding their spring pressure over time.

Supertech Hi Rev Spring/Retainer Kit 91-99 3000GT Stealth 6G72 DOHC (SPRK-M1007S3000) - Ninja (http://www.ninjaperformance.com/supertech-rev-springretainer-kit-3000gt-stealth-6g72-dohc-p-2126.html)

-Chris
i have not heard anyone who said the bc springs are not good for 3/s. Von said they are good springs before I buy them. looking at their catalog they have different spring pressures for different brands. Imo if it doesn't work for some other platform it doesn't mean it wouldn't for us. the price are very comparable to bc so it defiantly is not the price issue here to not buy the springs over others. I'm trying to compare the spring pressures but for some reason on the length on yours are not same as BC. on bc 39.37 is fully closed with 84lbs pressure. on yours it says 37.15mm fully closed at 102lbs. the supertech springs are pressed in over 2mm more unless they are 2mm shorter which i don't think it's the case here or the retainers are thicker or shimmed. same with open. BC valves gives 25.4mm with 235lbs and supertech with massive 11.5mm only gives 224lbs. unless i'm reading this wrong, BC springs seems stronger to me.

nodoze
04-09-2013, 10:13 AM
Interested in the plugs Chris , let me know of you can get them for a dsm . I'm running ngk bre6 atm I believe gapped down but if ican pick up some.power and reliability I'm game , nice graphs as well !

Sent from my HTC Hero S using Tapatalk 2

donniekak
04-09-2013, 11:55 AM
i have not heard anyone who said the bc springs are not good for 3/s. Von said they are good springs before I buy them. looking at their catalog they have different spring pressures for different brands. Imo if it doesn't work for some other platform it doesn't mean it wouldn't for us. the price are very comparable to bc so it defiantly is not the price issue here to not buy the springs over others. I'm trying to compare the spring pressures but for some reason on the length on yours are not same as BC. on bc 39.37 is fully closed with 84lbs pressure. on yours it says 37.15mm fully closed at 102lbs. the supertech springs are pressed in over 2mm more unless they are 2mm shorter which i don't think it's the case here or the retainers are thicker or shimmed. same with open. BC valves gives 25.4mm with 235lbs and supertech with massive 11.5mm only gives 224lbs. unless i'm reading this wrong, BC springs seems stronger to me.

I've run both bc's, and supertech duels in my 4g63, same springs and seats the 6g72 parts. First off, who on here has ever actually checked the installed height of the springs, and shimmed them to spec? The installed height recommended by bc isn't what you get if you just drop them in, they need shimmed. Supertechs come with a very thick spring seat that usually puts the installed height in spec, unless your valves sit really low in the seats.
The bc's would float around 8500 rpms on my setup. With a more aggressive cam, I can rev over 9000 no problem on the supertech duels.

In general it's been found on several boards I'm on that bc products have some of the lowest quality control in the aftermarket engine parts market. A guy on a Dsm forum I'm on bent his valves from float running bc springs on a huge cam, at about only 5000 rpms. Several other members have actually broken the springs.

AdamVR4
04-09-2013, 03:45 PM
I put these in a while ago with the stock Mitsu Hydro tensioner and it has been beat on and to the rack that way with no issues. So I would say you will be fine.

-Chris

Did you bottom-out the tensioner or did you install it at stock tension (grenade pin freely slides in and out)?

mehrshadvr4
04-09-2013, 04:26 PM
I've run both bc's, and supertech duels in my 4g63, same springs and seats the 6g72 parts. First off, who on here has ever actually checked the installed height of the springs, and shimmed them to spec? The installed height recommended by bc isn't what you get if you just drop them in, they need shimmed. Supertechs come with a very thick spring seat that usually puts the installed height in spec, unless your valves sit really low in the seats.
The bc's would float around 8500 rpms on my setup. With a more aggressive cam, I can rev over 9000 no problem on the supertech duels.

In general it's been found on several boards I'm on that bc products have some of the lowest quality control in the aftermarket engine parts market. A guy on a Dsm forum I'm on bent his valves from float running bc springs on a huge cam, at about only 5000 rpms. Several other members have actually broken the springs.

again don't compare dsm to 3/s. I searched a ton for bc springs and some people over there don't even know the difference between crower and briancrower brand and that was the one people break. a lot of people had good luck with bc springs. supertech springs that are available for 3/s are single spring not dual. I highly doubt that the springs are same on 3/s since no one as far as i know have run dsm springs on 3/s. and looking at the height the bc is putting more pressure on the seats. the height of valve and seats make huge difference on spring pressure. plus there is a presigure to break in the springs. you don't just put the on a rev the hell out of the engine. people who don't break in the springs are the one dangering breaking springs.

AdamVR4
04-09-2013, 04:31 PM
supertech springs that are available for 3/s are single spring not dual.

Actually, it appears they have 3 flavors available, including a dual spring:

Supertech Valve Spring Kits | Ground Zero Performance (http://www.groundzeroperformance.com/product/valvetrain/supertech-valve-spring-kits)

This thread may interest you: http://www.3sgto.org/3000gt-stealth-gto-related-topics/11730-valve-spring-selection.html

I've got some more data, so I'll update it tonight I think.



I highly doubt that the springs are same on 3/s since no one as far as i know have run dsm springs on 3/s. and looking at the height the bc is putting more pressure on the seats. the height of valve and seats make huge difference on spring pressure. plus there is a presigure to break in the springs. you don't just put the on a rev the hell out of the engine. people who don't break in the springs are the one dangering breaking springs.

I had no idea there was a break-in procedure. Bring this info and your rationale for spring selection to the valve spring selection thread! ;)

mehrshadvr4
04-09-2013, 10:11 PM
yeah I had no idea either till last night searching for spring pressure. What i could get from it was don't rev the engine more than 1500-2000rpm for first start and let the engine warms up to operating temp and then shut the car and let it cool down to ambien ambient temperature. before when i was searching most DSMs had good luck with bc springs. on 3/s i haven't heard of anyone having problem yet probably because we don't rev to 9k all the time. dual springs will give you better valve control for sure, but for single springs and ~8500rpm bc are great.

donniekak
04-09-2013, 10:21 PM
again don't compare dsm to 3/s. I searched a ton for bc springs and some people over there don't even know the difference between crower and briancrower brand and that was the one people break. a lot of people had good luck with bc springs. supertech springs that are available for 3/s are single spring not dual. I highly doubt that the springs are same on 3/s since no one as far as i know have run dsm springs on 3/s. and looking at the height the bc is putting more pressure on the seats. the height of valve and seats make huge difference on spring pressure. plus there is a presigure to break in the springs. you don't just put the on a rev the hell out of the engine. people who don't break in the springs are the one dangering breaking springs.
The bc 4g63 springs, and 6g72 springs are the same part. People also use stock evo springs all the time in 6g72's. I also have yet to see a build thread with someone actually checking the installed height.


Springs don't break in. The break in procedure of holding rpm, and then cooling down is for solid lifter cam in block engines with big cams, and stiff springs. It is done to prevent wiping the cam.

familyMAN
04-09-2013, 10:49 PM
Wonder if my Dynamic Racing High rev spring kit is the dual spring supertech kit.

mehrshadvr4
04-09-2013, 10:53 PM
uhm they are saying different thing here.
COMP CamsŪ - Sorry... (http://www.compcams.com/Pages/415/truth-about-valve-springs.aspx)
I have my heads at home with BC springs. I'll try to find a way to measure the valve height from the bottom.

Ninja Performance
04-10-2013, 12:15 AM
Now, My HIGH boost (36psi or about) on E95M5 were always scary looking. But after a year of beating on it, tracking it many times in the low 10's and 140-144mph range I tore it down last July for a last rebuild/track run before my bone marrow transplant, and as the time before, the bearings looked like they had 100 miles of easy driving on them.

But with the Champion race plugs and noise floor is WAY lower and power is up. Detonation is NOT making power. And the car felt smoother and stronger, and these VD runs showed a little more power.

So as you look at the before log, which was a superflow dyno 796AWHP 727AWTQ, keep in mind I would NOT tune like this and on a customer's car, especially on any type of non 100% alcohol fuel I would cringe at this log. But for my setup if has proven itself to stay together. BUT with lower noise floor and new found smoothness and power I feel it was real and the next track event should be interesting.

These really show the possibility that VD is showing REAL new HP, Detonation hinders power.

BEFORE with NGK Coppers
http://www.ninjaperformance.com/images/noiseNGKcopper36psi.jpg


After with Champion Race Plugs
http://www.ninjaperformance.com/images/noiseChampraceplug36psi.jpg

-Chris

mehrshadvr4
04-10-2013, 01:25 AM
that's a very good difference.

Chris@Rvengeperformance
04-17-2013, 12:17 PM
The C53vc plugs came in today. That is a funky looking plug, lol.

I'd love to test them on 93 for you guys, but when I switch to e85 I'd rather foul my current plugs getting the tune close than foul these.

futurevr4man
04-17-2013, 02:14 PM
yeah i have some here as well, but i am going to finish tuning on my current setup then do back to back VD's and see if there is an immediate change. i will also write up if i am able to run any more boost, or anything like that. i have great excite!

familyMAN
04-17-2013, 02:30 PM
The C53vc plugs came in today. That is a funky looking plug, lol.

I'd love to test them on 93 for you guys, but when I switch to e85 I'd rather foul my current plugs getting the tune close than foul these.

They are wild looking aren't they:) I put one in a set of heads on the shelf just so I could see it. Fits perfectly flush, and looks great with just the little button sticking out.

Ninja Performance
04-23-2013, 06:49 PM
Plugs In Stock in 2 days

CHAMPION Race Plug 694 C53VC Set of 6 (C53VCX6) - Ninja Performance - Affordable Performance Auto (http://www.ninjaperformance.com/champion-race-plug-694-c53vc-set-p-21866.html)

-Chris

Greg E
04-23-2013, 07:44 PM
Damn Chris! I might have to pick a set of these up from you!