View Full Version : Revival of the Blue Bastard
stealthee
03-30-2013, 10:59 PM
I think the time has come to get the Stealth back on the road, or at least to start working on it.
The purpose of this thread is to document what needs done, and the progress that I make. I’m hoping by starting this thread it will keep me motivated to keep things moving to get it roadworthy once again.
I really don’t want to post pictures right now as I am basically ashamed of the shape I let it get into. I will take pictures and document progress as I go, though.
I apologize for the lengthiness of the thread ahead of time, but there is a lot to do.
Engine and Transmission
I still have the Quaiffe differential trans sitting in the garage that has a busted 2nd gear. My intention is to open the Quaiffe trans, pull the trans from the car, open it up, and then swap the gearset into the Quaiffe trans to have a good trans once again.
Engine-wise I got a 95 Fed spec ECU and wiring harness. My car is Cali-Spec so I have the pain in the ass pre-cats. Since I already have the ECU and harness the only thing I really need to complete the swap is a Fed-spec rear manifold, a Fed-spec downpipe, and the o2 sensor.
I talked to Hans and he was going to sell me a manifold for $40. The downpipe will be the expensive part, unless I can procure a used one, since I really want to stay with the 3sx one. There was a guy here trying to sell one for $100, but he disappeared before I could get it.
Since I will be doing all of that work with the swap, and since the trans will be coming out I figure I may as well pull the engine too. I plan on going over it, cleaning it up really well and replacing gaskets wherever they need replaced. For anyone that doesn’t know, the SOHC’s like to leak from anywhere and everywhere. I may go ahead and pull the heads and get them cleaned up while I am at it, but that isn’t 100% necessary. I may also just pull the heads, replace the headgaskets, and go from there.
Also, while the engine is out, I can clean up the engine bay really well and go ahead and paint it. Will probably just do it gloss black with rattle cans, unless I actually make a final decision on the color and do it body color.
When I put the engine back I want to look into putting AC back into the car. I’ll have to get a new condenser, as mine has a hole in it, and put all the lines back on, and of course look into replacing all the orings.
Body
The body is in poor shape at best. The Victory hood, sad to say, needs some repair. In January 2010 the car was overheating on my way to work and I pulled off the side of the road to check it out. I popped the hood to check things out, topped off the overflow, shut the hood and got back in the car. The temp immediately dropped so I pulled back onto the road. As I got up to speed, the hood came up and hit the windshield….. it didn’t latch when I shut it. It ripped off where it bolts to the hinges. The topside of the hood is okay, probably 90%, but it needs some work to get it to work like normal, and look 100%.
The driver’s door needs replaced, but has been in need of replacement for probably 5 years now. The passenger fender is in need of replacement too. I need to put the RT door caps on. Thankfully, I have that stuff on hand. As some of you remember I had an incident a few months before I parked the car that caused some damage to the 99 front. Looking it over, I probably could fix it, but I have to figure out if it’s worth my time, or if I just need to buy a new bumper cover. I am going to swap the rear bumper cover from a 1g 3000GT, to 2g 3000GT. I have that on hand too. The only way that will change is if I find a hellacious deal on a 2g RT rear conversion.
I want to look into getting the Cianci/C7 widebody rear quarterpanels. Mainly want them to save on removing dents and dings in my quarters.
I plan on swapping to RT sail panels too. That will involve interior panel removal at paint time, so that might wait until paint happens.
The only other plan for the body is figuring out if I want to use the Cianci duckbill I have. If I don’t use it I will have to put some work into the hatch to get all the dings out. I may actually just replace it since half of my defrost lines don’t work anyway.
Interior
I actually started an interior swap already. I got ahold of a true black leather interior from a 97 base a year or so ago. I sold the charcoal cloth interior I had in it to my cousin, Roger, who sometimes posts here. The seats aren’t bolted in place because I still need to swap the carpet. Basically, I want to clean the black carpet really well and put the whole interior back together.
I want to pull the dash and swap in a 1g dash to get rid of the passenger air bag. I want to go with an aftermarket steering wheel too. Probably will paint or dye the dash black and put in new vents while I am at it.
I need to figure out what to do with the door panels. They are in okay shape. I would say they are 60-70%. I may get them recovered, or may see if I can find a good set on a part out.
Wheels
I want to get the Villains powdercoated. Probably go wth black chrome, or gunmetal.
So there it is. I probably overlooked something that needs done, but that is my list.
FeaRpb
03-30-2013, 11:00 PM
Awesome. Can't wait to see some updates.
CoopKill
03-30-2013, 11:05 PM
Sweet!
2fnloud
03-30-2013, 11:22 PM
You can do it, looking forward to your progress.
CoreyB
03-30-2013, 11:28 PM
Its about damn time Brian. Looking forward to this thread.
subbed. post up if you need parts. i'm sure you probably have everything you need...but just in case...
Street_Chally73
03-31-2013, 02:18 AM
Good to hear, man!!
Sent from the garage
stealthify
03-31-2013, 03:12 AM
Sounds like a great spring project, Brian! It's very cool to see people motivated to get their car back on the road. How long has yours been sitting?
Primus101
03-31-2013, 03:28 AM
How long has it been parked for?
stealthee
03-31-2013, 11:04 AM
It went down end of February 2011.
As for parts I have most of what I need. Main things I need to purchase are the SOHC Fed-spec rear manifold, Fed-spec o2 sensor, engine gasket set, and if I decide to do it, the widebody rear quarters.
I'll need to get my engine hoist back to the house, since it is out on loan. I don't wan't to pull the engine and trans until I have what I need to do the Cali-spec to Fed-spec swap so that I am not pulling the engine twice.
I may look at putting a better clutch in in the process too. The clutch that is in my car now isn't that old, but its a cheap Zoom one from Advance. Anytime I ever went WOT with that clutch I had to go back and make clutch adjustments immediately afterwards. Something isn't normal about it.
Another thing I forgot to mention I want to look into doing is going to stock drivers and passenger side engine mounts. I will keep the solid front and rear.
I'll need to clean the coilovers up as they have surface rust from sitting. The rest of the suspension, minus the rear LCA mounts, has over 190k miles on it. I probably need to look into replacing front subframe bushings, and may just replace the both front LCA's.
Honestly, the only work that needs to be done to make it driveable, is the trans, but it needs so much more to be "roadworthy."
OhioSpyderman
03-31-2013, 02:38 PM
Great news Brian :)
You can do eet!!!
Good Luck, sir.
Bob.
Granny
03-31-2013, 03:06 PM
Yea!
I'll be checking in on ya. :)
AdamVR4
03-31-2013, 04:46 PM
Just fyi, when ive searched about p'coating wheels, lots of people say the high heat negatively impacts the wheel strength.
stealthee
03-31-2013, 05:20 PM
I'll keep that in mind Adam. I might have to look into other options. Worst case I will paint and clear them.
Just fyi, when ive searched about p'coating wheels, lots of people say the high heat negatively impacts the wheel strength.
i would guess that also depends on the type of manufacturing process. i don't believe forged wheels are going to be negatively impacted like cast wheels might be.
CoopKill
03-31-2013, 08:52 PM
Just fyi, when ive searched about p'coating wheels, lots of people say the high heat negatively impacts the wheel strength.
Problem is "people" say. I researched this some as well. Talk to your coating company to see if they have a 300~* product to use. Research the coater, talk to them, ask questions, if they seem ignorant about annealing alloys, RUN.
Some info on the subject: New Page 1 (http://www.uniquefinish.com/coastingwheelsafely.htm)
wingnut
03-31-2013, 08:58 PM
Some info on the subject: New Page 1 (http://www.uniquefinish.com/coastingwheelsafely.htm)
Good link...i was gonna say, i tend to coat at 400* but it takes all of 20 minutes and surely any metal wheel can handle that :wink:
Oh...and im in for pics of the blue bastard :lol:
AdamVR4
03-31-2013, 11:38 PM
i would guess that also depends on the type of manufacturing process. i don't believe forged wheels are going to be negatively impacted like cast wheels might be.
Yes and maybe. It depends entirely on the aluminum alloy, microstructure (heat treatment, manufacturing process), and the powdercoating proces temperature and time.
The good news is that ive got good notes on this subject from materials 2 and I was already planning to look into it. Pm me if I forget to update this thread in the next month.
mb3000
03-31-2013, 11:41 PM
You guys would be surprised how hot the wheels get after some spirited driving/braking!
AdamVR4
03-31-2013, 11:51 PM
Problem is "people" say. I researched this some as well. Talk to your coating company to see if they have a 300~* product to use. Research the coater, talk to them, ask questions, if they seem ignorant about annealing alloys, RUN.
Some info on the subject: New Page 1 (http://www.uniquefinish.com/coastingwheelsafely.htm)
Encouraging for sure, but while he cites a legit source for the data, his consice/vague conclusions are like, his opinion, man :)
AdamVR4
03-31-2013, 11:53 PM
You guys would be surprised how hot the wheels get after some spirited driving/braking!
So surprise us. Whats the temperature range of wheels after hard braking?
CoopKill
03-31-2013, 11:59 PM
Yeah, there are other sources that say stick to as close to 300* as possible. 400* @ 30 minutes can affect the metals around 2-3%. Which could be substantial if there is a low headroom of tolerance built in.
CoopKill
04-01-2013, 12:31 AM
More info I had saved. It true will be effected by the alloy used. Metal and Metallurgy engineering - Aluminum wheel failure after powder coating? (http://www.eng-tips.com/viewthread.cfm?qid=151053)
Maybe we should ask Allen to move this to a new thread to clean up Brian's build thread?
Sorry for the rabbit trail Brian!
mb3000
04-01-2013, 12:33 AM
So surprise us. Whats the temperature range of wheels after hard braking?
You've caught me without my temperature gun!
The last/only time I took temperature readings was after bedding in my new pads. The temp of the wheels around the hub was enough to startle me. I don't want to just spit out a number, because I'm sure it will be wrong.
I also don't want to replicate the experiment because I'm sure my engine will let go (don't know how it didn't blow the first time, now that I think about it).
R/T93
04-01-2013, 12:43 AM
My wheels are 150-200 after half hour sessions on a road course. Nothing to worry about really.
From the phone.
Glad as I can be to hear you're finally going to get started, Brian.
Your car was one of the first in the long line of blue 3Ss I've coveted. :)
green-lantern
04-01-2013, 02:54 PM
8:1 TT, getrag swap, chromed ECU :)
8:1 TT, getrag swap, chromed ECU :)
Ah...there you go. :)
J-Groove
04-01-2013, 04:52 PM
That is awesome!!!
http://1.bp.blogspot.com/-4vGvDRXjXOc/Tiu4oDueBlI/AAAAAAAAACQ/7ehYWsd0Yus/s1600/back.jpg
Greg E
04-01-2013, 04:56 PM
So when is the next game of kings?????
8:1 TT, getrag swap, chromed ECU :)
why even mess with chrome? tt-ecu & a piggyback. proven, simple, easy. no teething pains like with clone ecus.
J-Groove
04-01-2013, 06:26 PM
why even mess with chrome? tt-ecu & a piggyback. proven, simple, easy. no teething pains like with clone ecus.
???? I've run piggybacks and I've run chrome. In my experience Chrome ECU has been much easier than Piggybacks for setting up a car.
-John
why even mess with chrome? tt-ecu & a piggyback. proven, simple, easy. no teething pains like with clone ecus.
yeah right
keep it simple stupid
:Bow:
???? I've run piggybacks and I've run chrome. In my experience Chrome ECU has been much easier than Piggybacks for setting up a car.
-John
i keep seeing threads on here about problems with clone ecus. maybe serious, maybe not--but there are some issues. either there is inherent problems, or the technology is still new enough that all the solutions aren't widely understood.
an safc2, on the other hand, can be successfully programmed by just about anyone (provided you have a wideband). both ray and matt swear by piggybacks for all but seriously high hp applications (although matt prefers arc and ray prefers safc).
not knocking chrome--i just think tried/true is easier to fire/forget.
Greg E
04-01-2013, 07:12 PM
why even mess with chrome? tt-ecu & a piggyback. proven, simple, easy. no teething pains like with clone ecus.
Is this a serious post?
Setting up a flash ECU is simpler than any piggyback and even standalones out there.
Greg E
04-01-2013, 07:12 PM
i keep seeing threads on here about problems with clone ecus. maybe serious, maybe not--but there are some issues. either there is inherent problems, or the technology is still new enough that all the solutions aren't widely understood.
an safc2, on the other hand, can be successfully programmed by just about anyone (provided you have a wideband). both ray and matt swear by piggybacks for all but seriously high hp applications (although matt prefers arc and ray prefers safc).
not knocking chrome--i just think tried/true is easier to fire/forget.
Ray bought a clone ECU.
CoopKill
04-01-2013, 08:34 PM
Most of the threads with issues are new to tuning people that are cutting their teeth on Chrome. I am one of these people. No matter the tuning tool (chrome, stand alone, or piggyback) they take a minute to get used to the terrain...
stealthee
04-01-2013, 08:37 PM
So when is the next game of kings?????
LOL. I will play kings again as long as we don't play flip cup beforehand. Finishing a 1/5 of Captain in under two hours was NOT the brightest moment of my lifetime.
Greg E
04-01-2013, 08:40 PM
LOL. I will play kings again as long as we don't play flip cup beforehand. Finishing a 1/5 of Captain in under two hours was NOT the brightest moment of my lifetime.
Ill help you this time. Don't forget to film our progress!
Does Kevin or Garrett still have that video?
wingnut
04-01-2013, 08:41 PM
Finishing a 1/5 of Captain in under two hours was NOT the brightest moment of my lifetime.
http://www.m5board.com/vbulletin/attachments/e39-m5-e52-z8-discussion/114851d1283611984t-stock-shifter-welder-free-short-shifter-worthless-without-pics.bmp
Greg E
04-01-2013, 10:18 PM
http://www.m5board.com/vbulletin/attachments/e39-m5-e52-z8-discussion/114851d1283611984t-stock-shifter-welder-free-short-shifter-worthless-without-pics.bmp
The rapture video is worth posting!!!!!
Who has a copy of it??
stealthee
04-01-2013, 10:30 PM
It might even be on Youtube. If not, Kevin should have it.
CoreyB
04-02-2013, 12:09 AM
Brian, get on with the progress, this thing should be about done by now.
Maximal
04-02-2013, 09:36 AM
Is there a reason you're swapping gearsets instead of just the quaife? I know when I blew out some gears most of the bearings were shot. It might be better just to move the quiafe over into the tranny that's currently in the car. Plus you're just dropping one assembly instead of all the gearset assemblies.
green-lantern
04-02-2013, 12:42 PM
???? I've run piggybacks and I've run chrome. In my experience Chrome ECU has been much easier than Piggybacks for setting up a car.
-John
:stupid:
Screw piggy backs, nobody should run them anymore. Chrome is proven....Ignorance is proven to cause horror with any tuning device, that's why I don't really touch mine. lol
stealthee
04-02-2013, 06:43 PM
Is there a reason you're swapping gearsets instead of just the quaife? I know when I blew out some gears most of the bearings were shot. It might be better just to move the quiafe over into the tranny that's currently in the car. Plus you're just dropping one assembly instead of all the gearset assemblies.
Haven't verified it yet, but pretty sure I have a hole in the bellhousing.
Right before I parked the car I noticed shifting getting notchy and the trans starting to whine. I opened the drain plug and not a drop came out.
Honestly, I will have to wait and see what the Quaiffe trans looks like before I can make a final decision. Hopefully the amount of time I drove it with the trashed 2nd gear didn't mess up anything else.
Maximal
04-02-2013, 07:06 PM
It happens quick. I basically just drove the rest of the drag strip and they were trashed. Even if you need to swap bellhousings around you probably have a good gearset somewhere you can make it work between the two.
:stupid:
Screw piggy backs, nobody should run them anymore. Chrome is proven....Ignorance is proven to cause horror with any tuning device, that's why I don't really touch mine. lol
i respectfully disagree. there's even more variables to dork up with chrome than on a piggyback. nor would i say chrome is proven; promising, but not proven. show me the first 3 cars running 9's with them. show me the first 3 guys who were successfully running AEM and are now successfully running chrome. show me the long-standing with sticky that neatly outlines the how-to's for using. show me the link in stealth316.
there's NOTHING wrong with piggybacks.
stealthee
04-02-2013, 08:12 PM
It happens quick. I basically just drove the rest of the drag strip and they were trashed. Even if you need to swap bellhousings around you probably have a good gearset somewhere you can make it work between the two.
Swapping the gearset isn't that bad. The Quaiffe trans is hole, with no holes. Once both are open I can have the Quaiffe trans ready to go back together in an hour or so. I am going to take my time though and make sure everything is properly shimmed.
Shims are one thing I need to look into. Hopefully between the two trans I have the right size that I need.
Another thing I forgot to add to my list is replacement 99 corners. Its been awhile, but some may remember the story. I was on my way home at about 2 am several years ago and I was giving the car some hell. Rounded a curve in the road and there were about 10 deer standing there. Got hard on the brakes and the deer scattered, but two of them ran in place Scooby Doo style and I caught them both with both of the front corners of the car breaking both corners. Once lense was completely broken off, the other had a corner broken off it.
I also need to "restore" my GTO tails. They were used when I bought them on Ebay 9 years ago and have faded a little over the years. I am hoping to be able to open them up and clean the inside really well, then I will wet sand buff, and maybe clear the outside to make them look like new.
Greg E
04-02-2013, 09:12 PM
i respectfully disagree. there's even more variables to dork up with chrome than on a piggyback. nor would i say chrome is proven; promising, but not proven. show me the first 3 cars running 9's with them. show me the first 3 guys who were successfully running AEM and are now successfully running chrome. show me the long-standing with sticky that neatly outlines the how-to's for using. show me the link in stealth316.
there's NOTHING wrong with piggybacks.
No there isn't anything wrong with piggy backs.
...buy how many 9 second 3/S are there???? 3 by my count. One runs and ARC2, the other two run AEM. How long ago were those record set? Before chrome came out?
How many 10 second 3/S are there? Not many. What are they running? Again all those cars were built and set their runs... Before chrome.
Lets look at the results with chrome. How many people have had success? Honestly. Just me, Nick and Toni... A stock 98 VR4 gained .3 tenths over a comparable completely stock car and 2 BPU cars ran consistant mid-12s in the 1/4 mile during a hot/humid summer day.
I'm sorry that these results aren't good enough for someone who, as far as I can tell, has done nothing with their car but as far as potential is concerned, time will tell. Assuming there are enough owners left, who care about setting the bar, chrome will be proven to you.
i hope so, greg. i really do.
Greg E
04-03-2013, 09:37 AM
Just noticed this discussion is taking place in a SOHC build thread. There isn't a version of chrome for the SOHC cars. :lol:
Sorry Brian.
Chris@Rvengeperformance
04-03-2013, 01:15 PM
i hope so, greg. i really do.
I certainly do not understand those who think somehow the flash ecu is magically inferior to a stock 3/s ecu.
Anything you can do with the stock ecu the flash ecu can do. I guess some people would rather run 2,3,4 piggybacks, lol. I mean comeon guys you can't even change the rev limit without a different crystal roflmao.
You can change as much or as little as you want. The extra "variables" can be left alone if it really pleases you. Having access to most of the tables in the ecu certainly doesn't require you to alter them. If you want there is a usermode feature in ecuflash where you can hide some of the scary ones :lo5l:
AdamVR4
04-03-2013, 01:17 PM
I certainly do not understand those who think somehow the flash ecu is magically inferior to a stock 3/s ecu.
Anything you can do with the stock ecu the flash ecu can do. I guess some people would rather run 2,3,4 piggybacks, lol. I mean comeon guys you can't even change the rev limit without a different crystal roflmao.
I love the flash ECU, I just can't justify it right now since no one wants to buy any of my piggybacks :lol:... My complicated rats nest of piggybacks works well and there's so much other stuff to buy that it just falls down the list. Leave my crystals out of this! haha
Chris@Rvengeperformance
04-03-2013, 01:22 PM
I love the flash ECU, I just can't justify it right now since no one wants to buy any of my piggybacks :lol:... My complicated rats nest of piggybacks works well and there's so much other stuff to buy that it just falls down the list. Leave my crystals out of this! haha
Certainly no arguing with your results! But, I think you'd find the investment in the chrome stuff worth it. You can always sell 1G ecus that are good, especially a 93 one, so that would go a long way. The emanage stuff will still sell if you give it some time. You could always go to ebay, a lot of other platforms still need them. My buddy wants to turbo his miata and the flyin miata stuff not withstanding I think the emanage wouldn't be a bad option for him.
i'll keep that in mind as well, forest. i'm also unclear on how chrome will eliminate the known problems with tcu/ecu interface for turbo cars.
I love the flash ECU, I just can't justify it right now since no one wants to buy any of my piggybacks :lol:... My complicated rats nest of piggybacks works well and there's so much other stuff to buy that it just falls down the list. Leave my crystals out of this! haha
piggybacks are universal. sell them on ebay.
Chris@Rvengeperformance
04-03-2013, 02:53 PM
i'll keep that in mind as well, forest. i'm also unclear on how chrome will eliminate the known problems with tcu/ecu interface for turbo cars.
I can't see how it would help or hinder you.
green-lantern
04-03-2013, 04:20 PM
Lets look at the results with chrome. How many people have had success? Honestly. Just me, Nick and Toni...
I think there is a thread around here with a list of people that think they have had success.
I can't see how it would help or hinder you.
then--given my current SAFC2--there's not a lot of reason to justify migrating. :(
Chris@Rvengeperformance
04-03-2013, 07:12 PM
then--given my current SAFC2--there's not a lot of reason to justify migrating. :(
there are tons of reasons, but whatever floats your boat. What issues do you have with your TCU?
TCU and ECU (tt-spec) do not communicate natively. as a matter of fact, i think it's one of the error codes that my car keeps throwing. granted, it works fine, but not the ideal solution.
i guess i'd just want more of a benefit from switching. i already have all the tuning (that i'd ever mess with) native in the SAFC2.
in any event...sorry for hijacking this thread for far too long. keep us posted on progress, brian.
stealthee
04-03-2013, 09:02 PM
Only progress I have made is remembering more things to add to my list.
Another thing to add is the damn sunroof. I have a shitty aftermarket roof that has been in the car since before I bought it. The latch is broke so it doesn't even latch anymore. I have two options. Option 1: Find a place local that can install a better, slightly larger, aftermarket (possibly power) sunroof. Option 2: Swap the entire roof to a non sunroof style that my car originally was.
Both options will probably cost me between $300-$500. Option 2 would be my preferred option, but it would also be my most labor intensive on myself.
I have to get the garage reorganized before I pull the Stealth in. It is not really dirty, just needs a little work. I spent about 40 minutes out there tonight getting some garbage out of there and loaded into the Grand Prix to go to the dumpster tomorrow.
I plan on spending a few hours tomorrow getting everything where I want it.
Friday I plan on detailing the Grand Prix, then after that I will see about getting the Stealth pulled in. I will take pictures before she goes into the garage, and as parts start coming off.
Since I don't have my engine hoist right now I will start on some of the body stuff first. I'll talk to my cousin to see about getting the hoist back at the house.
if you know the brand of sunroof, you might be able to wholesale purchase just the parts you need to repair it. the latch assembly for my funsport was <$50.
stealthee
04-03-2013, 09:15 PM
Ironically, mine is a Funsport, but I had no luck sourcing parts for it when I actually did look to replace the latch.
The thing is crappy, and I had to "modify" the seal to keep it from leaking. If I am going to have a sunroof, I would rather have a nice new one, than try to salvage the old shitty one.
yeah, in that case, it might be easier to just replace it altogether. i sourced my stuff through a tint-shop...since that's normally the type of place that does sunroofs.
stealthee
04-06-2013, 07:48 PM
I didn't get the Stealth in the garage today as planned, because it took a lot longer to hose the floor out because I ended up hosing the driveway too to keep mud out.
I did however manage to take the black carpet out and hose it off really good. I vacuumed it to get excess water off and it is drying now. It looks aweseome and I can't wait to put it in. I need to get some leather cleaner and conditioner to get the seats cleaned up really well and looking just as good.
Car should go in tomorrow but now sure how much I will get done as I need to take a look at the headlight wiring on my mom's car so she actually has two low beams.
stealthee
04-07-2013, 06:56 PM
Well, Stealth has been put in the garage. Really didn't want to get started into too much today as I have had a busy, put productive, weekend doing other things, and need to relax for the evening.
I took pictures before I put the car in the garage, but I haven't uploaded them yet. I am embarrased by the condition. :/
Talking to my mom tonight about some stuff, and how we are still looking to move, I might have to slightly alter my plan of a full revival right now.
I think I'll be trying to get the interior done, at least all but the dash first. This will suck when it comes to installing the RT sail panels that I think I previously forgot to mention. I'll have to basically remove the entire interior to get the to the B and C-pillars for install. It's not a huge deal, but it is what it is. I might try to install them now, but will probably have to remove them when it comes time for paint anyway. Grr, I'm rambling now.
Anyway, I think I might just look into just getting the trans out, torn down, reassembled, and reinstalled so it is driveable (safely, without worrrying about the trans grenading due to lack of lubrication). I can put off the Fed-Spec swap and "engine clean-up" until a later time.
I'll do what I can on the body.
I need to start checking yard sales and Craigslist because I am finding myself in need of a bigger toolbox and other tools. I just can't keep my tools as organized as they need to be. I really need to look into a compressor. I currently have an old one on loan that belongs to my uncle, but it barely works, and I would rather have my own.
CoreyB
04-07-2013, 07:08 PM
Post the pics, don't be embarrassed man. The worse it looks the better. It will make for a really good benchmark and will make any improvement look that much better.
stealthee
04-07-2013, 10:50 PM
Shamefully, here are the pics. This is how she looked right before I put her in the garage.
http://www.3sgto.org/members/stealthee-albums-revival-picture5218-dscn0109.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture5216-dscn0106.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture5214-dscn0103.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture5212-dscn0102.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture5217-dscn0107.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture5218-dscn0109.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture5215-dscn0104.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture5219-dscn0110.jpg
She needs some lovin', Brian.
Give it up...:)
CoopKill
04-07-2013, 11:25 PM
That will buff out!
Street_Chally73
04-07-2013, 11:32 PM
Is that an OEM rear wing or a repro?
Sent from the garage
stealthee
04-07-2013, 11:35 PM
Replica. It was done by Vital Velocity back in the day. I think CTY and me were two of the first ones to get them off him.
what happened, brian? i don't recall reading about body damage when you stored it. did you get clipped by an illegal?
stealthee
04-07-2013, 11:56 PM
I posted a thread a few months before it got parked from where a guy had a piece of equipment fall of his truck and it jacked up the front bumper cover.
The marker lights are busted from smacking two deer at once.
The driver's door has had a dent for several years now. My dad was grinding on a set of CJ doors in the driveway when the zek disk blew apart. A chunk hit the door.
Passenger fender was a fit of rage. Door caught the fender one day and I was already having a bad day so I just yanked the door open and basically caved the fender in. I pulled most of it back out later so the door was functional.
A clip broke on the drivers sideskirt just recently.
To this day I don't know what happened to the rear bumper cover. Someone must have bumped it in a parking lot.
Like I said, it was seriously neglected. All I did for the longest time was drive it, put gas in it, and change the oil. And of course pull the transmission 20 times. LOL
wingnut
04-08-2013, 12:27 AM
Well, you got your work cut out for ya, so list the priorities and get on it http://forums.shinsen-radio.org/Smileys/cool/smiley-hammer.gif
...now get busy, post progress pics and we will keep you motivated...one way or another :suspect:
stealthify
04-08-2013, 07:13 AM
You'll feel much better once you clean her up. A perfect spring project.
CoreyB
04-08-2013, 07:28 AM
Thats a good benchmark thats for sure. Anything you do from here will be an improvement. Looking forward to the progress.
HLxDrummer
04-09-2013, 08:15 PM
I think this car took my coilover and solid mount virginity:duckhunt:
I have two things that might help you out!!!
I still have my stock flat roof from the car. Nicely drilled out spot welds... I was holding on to it just in case my sunroof mod didn't hold up. I'm never going to return it back now. I also have a 99 front bumper that has a gash in the middle/front. Let me know if you can use either of these!
green-lantern
04-10-2013, 11:02 PM
Shamefully, here are the pics. This is how she looked right before I put her in the garage.
Did you do a Dukes of Hazard jump and hide it for 10 yrs or what? lol
I can understand why you didn't want to post pics.
Glad you are bringing her back, if you need any parts let me know. I know you got a shit load of stuff but if you need any other parts don't hesitate to ask. I have a bunch now.
Greg E
04-11-2013, 09:14 AM
I still have my stock flat roof from the car. Nicely drilled out spot welds... I was holding on to it just in case my sunroof mod didn't hold up. I'm never going to return it back now.
I will take that roof off your hands if Brian doesn't want it.
stealthee
04-14-2013, 07:24 PM
Toni, can you post some pics of the bumper cover? I might very well be interested in both. It all depends on cost, and what it will cost me to either ship them, or to drive 6 hours to pick them up.
I haven't been as busy on the car as I would have liked to be. It's just so hard to get anything done in the evenings because I don't get home until after 5 and I usually eat dinner around 6, and usually try to be showered by 8:00 because I get up at 5am.
In between all that I have to continue to go through stuff in the garage and throw away whatever isn't needed anymore and sort through stuff so whenever I finally do move it won't be a huge project all at once.
Excuses aside I did get the interior stripped. I cleaned up the seats so they are good to go back in. I managed to get the carpet set back in but that's all the farther I got today. Hopefully though the week I will get the interior all put back together. I think I will be removing the interior when I paint it. Would like to have it match, even if you can't see it. I'll also have to at least pull the carpet back on the front when I do the ECU/harness swap for going Cali spec to Fed spec.
Once I get the interior put back together I should be ready to start on removing/swapping body parts. I just have to keep myself motivated. I got some depressing news last night and it killed my mojo for today. I washed the Grand Prix and was trying to distract myself, but got all side tracked on other stuff.
vr4tune
04-14-2013, 10:48 PM
Ever think about using her as a parts car and buying a different car? I applaud you diligent effort here but wonder if it would be cheaper to get a different 3s.
stealthee
04-14-2013, 10:55 PM
Hasn't even crossed my mind. Honestly, I already have a lot of the parts I need to make it drivable. The only thing I am going to be out now is time.
Even if I do EVERYTHING I want to do to it, I will only have about another $5,000 more into it. I won't be able to even get a decent car for that price.
CoreyB
04-14-2013, 11:24 PM
Brian, if you pick a weekend out in the future, one that wont make me miss a autox, I would be willing to drive down and help you out for a couple days. I know you dont need me in terms of knowledge and shit, but just have a beer drinking buddy around that has the same passion about the 3s as you could help get this project really going. Just a thought and an offer, hit me up sometime.
stealthee
05-05-2013, 12:05 PM
So its been a little while since I even bothered with the car. I was dealing with back spasms that made me want to do nothing but lie in bed.
It's official though, I am moving, next weekend in fact. I'm going to try to get the interior done today and that will probably be all I get done for a few weeks. I probably won't bring the car over right away. I just have to clear it with my dad that I can leave the car in the garage until I get a few things settled. I'll try to move all the parts and stuff in the moving truck though to avoid that hassle in the future.
stealthee
05-05-2013, 11:05 PM
Interior is in. Its as complete as it can be for now. I am actually missing a few small pieces, but nothing that is going to affect anything right now. The interior is probably the most complete it has been in 8 years. I hadn't had rear speaker panels in since probably 05.
I actually just reread what I posted, and its two weeks that I am moving. Probably still not going to get much else done to the car. Probably just going to get it ready to drive to the new place, throw some oil in the trans right before I drive it so it doesnt explode on the drive over. I'll start on body stuff once things are settled in at the new place.
GTOJOE
05-05-2013, 11:20 PM
LOL sounds like my car for a while. I took the drivers side under dash bit out 6 years ago and never bothered to put it back on until our NG last year :lol: interior panels are considered optional in a 3/S.
stealthee
05-05-2013, 11:40 PM
The worst part was try to remember how the rear speaker panels went in. I had the drivers speaker panel in and out at least 4 times. Once I finally got all the seatbelt routing figured out and was finishing it up I realized I had the front seat belts flip flopped so I had to take it back out AGAIN and swap the seatbelts.
The black leather is awesome though. Interior is a little of a mishmash of black and charcoal, but it works for now.
stealthee
05-07-2013, 07:57 PM
With a little ingenuity I was able to get my crappy aftermarket sunroof latched today. I made some latch "arms" out of 1/2" HDPE and had to create a hinge for the latch to swivel on, but it latches tight. At least when it goes back outside I don't have to worry about it leaking.
stealthee
06-06-2013, 10:54 AM
Haven't updated in awhile. I did post over on the "What did you do today" thread that I got it fired up and drove it from the old place to the new place. She drove surprisingly well for being on 2+ year old fuel and not being driven more than a mile in that same period. I don't really intend on doing too much to it until I get more stuff finished up around the house, so it will sit idle for a little while longer.
stealthee
06-13-2013, 07:38 PM
I fired the car up to move it on Tuesday so I could mow the grass where it was parked. I jumped in it and took it for a quick ride out the road while I was at it. I was able to get on the throttle a little more since I didn't have my mom following me, like I did when I brought it over to the house.
Later Tuesday night I went to run over to my uncle's place and the Pontiac was blocked in so I took the Stealth instead. I ran it hard and loved every minute of it. I also kept hearing a tinging noise everytime I hit a bump. When I pulled into my uncle's driveway I looked underneath the car I saw that the downpipe was broke right behind the flex. That explains why it is so loud. :lmao:
Oh well, just gives me more of an excuse to complete my Cali-spec to Fed-spec swap since the dp is different anyway. Maybe I can get the shed and the basement reorganized this weekend and then I can start planning on getting body stuff done to the Stealth.
Alan92RTTT
06-13-2013, 07:54 PM
I can hear the flex section in my SL drag when I hit a good bump. Its the second time a flex section has let go on the SL.
green-lantern
06-13-2013, 07:59 PM
Thread needs more pics
stealthee
06-13-2013, 08:47 PM
I can hear the flex section in my SL drag when I hit a good bump. Its the second time a flex section has let go on the SL.
I think mine rotted just from sitting
Thread needs more pics
Eh, car hasn't changed since the last pics.
Although...
http://www.3sgto.org/members/stealthee-albums-revival-picture5559-dscn0118.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture5556-dscn0121.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture5558-dscn0119.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture5560-dscn0122.jpg
green-lantern
06-13-2013, 08:54 PM
Well it shows you are working on it anyway :)
Flash Gordon
07-20-2013, 11:47 PM
Any updates?
stealthee
07-20-2013, 11:54 PM
I haven't done really anything to it lately. Between work stressing me out, and not having a garage, and the weather being either ridiculously hot, or rainy, I just haven't been able to do anything.
I know it's a poor excuse, but it is what it is. :/
green-lantern
07-22-2013, 09:46 AM
I haven't done really anything to it lately. Between work stressing me out, and not having a garage, and the weather being either ridiculously hot, or rainy, I just haven't been able to do anything.
I know it's a poor excuse, but it is what it is. :/
I know how it is man, I've been working 60hrs a week. I'm ether too tired or just don't have the time. I haven't touched my car in a while.
stealthee
07-22-2013, 02:33 PM
I went from working 4 10's back to 5 8's because the owner is a douschenugget. His nuggettness isn't helping in the stress department either.
stealthee
03-29-2014, 09:11 PM
Bump it.
It's been awhile since I posted in here, but I also haven't made any more progress on the car. Some time after my last post we did go back to 4 10's, but I still had to work at least a half day on Friday's, and then we went back to 5 8's. Ugh. As far as the stress department I have my fingers crossed that will be helped in the coming days. I took a pre-employment piss test for a place yesterday. Hopefully they call me this week.
Anyway, on to the car. I need some opinions here on which would be my best bet.
With option one I could probably get my car drivable in a weekend by pulling the trans, then taking it apart and the LSD trans (with broken 2nd) and making one good trans. I would put it back together and could have it drivable.
The main issue there is I do not have a downpipe that can bolt to it right now. I have a Fed Spec pipe I got in a swap. My 3sx downpipe rotted at the flex and then some. I also sold my front precat because of plans to go all Fed-spec.
I either need to acquire a set of factory fed spec manifolds, pick up Kevin's OBX headers, or try to make the Fed-spec dp I have work in order to make it truely drivable right now.
Option two is to pull the engine and trans, fix the trans, clean up the engine and engine bay, and do the wiring harness swap while everything is out.
Which would you guys do? With option one I could technically put the car back on the road, even though it still looks like shit. Option two will obviously take longer, but it is something that needs to happen eventually anyway.
green-lantern
03-29-2014, 10:03 PM
Probably 2
CoreyB
03-29-2014, 10:05 PM
Do work and post pics!!
HLxDrummer
03-29-2014, 10:09 PM
Option 2 in time for NG!
Beef6
03-29-2014, 10:11 PM
^ I have to agree with Lou on his one!
stealthee
03-29-2014, 10:18 PM
NG might not happen, in both the car being done, and me being able to attend. :/
HLxDrummer
03-29-2014, 10:48 PM
:confused2::eek4::shake2::mad::Sobbing::Spank:
mb3000
03-30-2014, 07:26 AM
I vote option 2, however request that you do not rush it. Take your time and make it enjoyable.
CoopKill
03-30-2014, 11:16 AM
2 for sure.
green-lantern
03-30-2014, 02:23 PM
NG might not happen, in both the car being done, and me being able to attend. :/
Ca-mon man, it's too close not to attend
stealthee
06-15-2014, 11:21 PM
Well, I decided it is now or never. The last time I tried to start the Stealth it was a no go. That was sometime last summer. After reading Chris' post about keeping gas in the tank it got me thinking about my car. I knew there was only about 2 gallons (or less) left in the tank because the idiot light was on last time I tried to start it. I was filling up my Grand Prix anyway and had 40 some cents off a gallon so I brought the gas can with me and put 5 gallons in it.
Today I jacked the car up and drained out the gas that was in the tank. It was far from fresh, obviously, but there didn't appear to be any water in it. I drained it anyway and put 5 gallons of fresh fuel in it. I tried cranking it over but the battery was weak. Hooked up the charger and tried again. Car was just cranking and not even attempting to start. Checked it out and had no spark. Had to fix the wiring going to the coil. It still didn't even want to sputter.
I sprayed some fuel in throttle body and hit the key and it still didn't even sputter. Realized I had a brain fart and didn't put the intake back on the throttle body. As soon as I did I hit the key and it fired to life and died. I sprayed fuel in the TB again and it fired and died again. I kept cranking after that and it fired up and stayed running.
It was loud as hell since it is open manifolds right now, but it sounded great to hear it running. I wanted to move it so I could actually mow the grass that you can't get to when it is sitting in its current spot. I put it in gear and realized the left rear wheel was locked up. I tried rocking the car back and forth but all I did was spin the tires a little and push the grass around with the dragging tire. I shut it down and jacked it back up to take the wheel off and beat the rotor with a hammer to break it free. Once it broke free the car moved under it's own power since last year.
I let it idle for awhile and everything was good. Right when I went to shut it down I blipped the throttle a few times and it looked like Old Faithful for a second, because a heater core hose exploded and shot coolant straight up in the air, so I shut it down.
I'm hoping to use this as motivation to get more things done on the Bastard. My biggest obstacle is not having a garage, well and money too. LOL My aunt and uncle are in the process of buying a house about 2 miles from me, and it has a garage, so I might try to use that to get me moving along on the project.
So there is an update. I make no promises of a timeline, because as I mentioned cash is a big obstacle, but I will do what I can, as I can.
wingnut
06-16-2014, 12:21 AM
Once it broke free the car moved under it's own power since last year.
Wooohoooo :triumphant:
stealthify
06-16-2014, 08:39 AM
That's definitely a start! Keep it up man.
sethduncan
06-16-2014, 02:29 PM
Yaaaay!
Sent from my Nexus 5 using Tapatalk
Greg E
06-16-2014, 05:33 PM
So what's the excuse for not bringing it to NG?
stealthee
06-16-2014, 06:47 PM
Well, there is still a hole in the transmission for one. There is no exhaust on it for two. I am not going to be able to attend NG for three, no money and too many other people off already. The car still looks like total poop for four.
Believe me guys I am very disappointed that I can't go, especially with it being so close to home, but it just wasn't meant to be. :cry:
Greg E
06-16-2014, 08:39 PM
It's so close to you that you could come out and hang out in the parking lot with us after you're done with work, drive home and still get a good nights sleep...
stealthee
06-16-2014, 09:01 PM
I am making no promises, but I may try to make it up to the drag strip to watch/hang out. I may also try to make it up the to car show, but, again, no promises.
stealthee
02-23-2015, 08:31 PM
It's really depressing that I started this thread just shy of two years ago and have made almost no real progress.
I drive A LOT for work, so I also think A LOT. I've had thoughts of just junking the car at times, but usually let them pass.
Today was different. Today, I started trying to game plan in my head how I can get the project moving forward again. Since my last post in this thread I have paid off ALL my debt. My Grand Prix, all my credit cards, everything is paid off. This frees up a little bit of money to play with. I've already sent a few PM's asking about some parts I need to or would like to acquire.
If I really wanted to I could just go on a buying spree and put everything on a credit card, but I am smarter than that now. LOL I want to start buying things I need a little a time right now and hopefully the weather starts cooperating within the next few weeks for me to start doing something to it.
My gameplan once the weather breaks is to remove the engine and trans. At that time I will probably also remove fenders, rear bumper cover, side skirts, etc. I need to talk to me uncle to see if he is willing to do some paint. If so I plan on removing the doors and the interior and having him spray under the hood, in the door jams, and everywhere you don't normally see. Once cured I can reassemble the body with the parts that need replaced, as well as the good parts that can go back on.
I will swap the engine harness and reinstall the interior as well. Once the engine and trans are ready they could go back in and at that point the car should be able to drive under it's own power at least.
After that I will start on the body work (with some help) and start getting the rest of the exterior ready for paint.
I don't know how long all this will take, but I absolutely want to get it done.
It seems my biggest expenses will be with the body as in replacing the 99 front and turns, (probably) replacing the hood, and the paint itself. Most everything else I have. I just need to keep my motivation going. I am going to talk to my cousin, who has assisted me a lot with the car over the years, to see if he can give me an extra hand, if only his hand is to keep me going on the car.
sketch
02-23-2015, 08:43 PM
One thing that I found that helped me out some was making a list of all the little projects that need to be completed and then attacking them one at a time. I found that doing that gave me a sense of accomplishment with each item rather than the sense of "I put in 18-20 hours this weekend and I feel like I've gotten nothing done."
Glad to see you ready to be back at it.
Brian, get it to a place or create a situation where it's ready to work on.
Get it on a hard surface, get it up in the air a bit, then stare at it a little more. :)
stealthee
02-23-2015, 10:02 PM
Brian, get it to a place or create a situation where it's ready to work on.
Get it on a hard surface, get it up in the air a bit, then stare at it a little more. :)
I may have mentioned it in this thread before, but, if not, my intention is to make my driveway larger. I have already spoken to my landlord and he basically said he didn't care. Now, it will still be gravel, but at least it will be more solid than grass and dirt. This is another project once the weather breaks. I am going to contact someone about pricing for the amount of gravel I need to make it the size I need.
Hopefully, I can get most of it tailgated to save me some backbreak. LOL
Beef6
02-23-2015, 10:42 PM
This makes me happy!
CoreyB
02-24-2015, 09:15 AM
I may have mentioned it in this thread before, but, if not, my intention is to make my driveway larger. I have already spoken to my landlord and he basically said he didn't care. Now, it will still be gravel, but at least it will be more solid than grass and dirt. This is another project once the weather breaks. I am going to contact someone about pricing for the amount of gravel I need to make it the size I need.
Hopefully, I can get most of it tailgated to save me some backbreak. LOL
Go with hard pack at least/ crushed blue stone. It is way better to work on than gravel and isnt a whole lot more expensive especially for the area you want to do.
Boomer3000
02-25-2015, 02:39 PM
Subbed!
stealthee
03-01-2015, 07:44 PM
I started a spreadsheet listing a bunch of OEM part numbers and prices for parts I am definitely going to need, as well as parts I may need. The total is around $1400 for everything I have listed, though, as I said, I may not need, or get all of it.
Not included in the $1400 is any top end gaskets I need or paint and materials. (I think) The only other thing I will need is figuring out my hood situation. I can't decide if I am going to try to repair my hood, or just sell it to someone who can repair it or wants to use it as is, and just buy myself a new hood.
Hood and paint are going to be my biggest expenses.
Weather looks like it should be about ready to break so hopefully I can get started and stay started so I can get the project moving forward. I already made one purchase for the project and I should hopefully have it next week. I will post photos once it arrives. :)
Beef6
03-01-2015, 07:48 PM
What's all wrong with the hood Brian? Let me know if you decide to unload it.
stealthee
03-01-2015, 07:56 PM
I can send you pics when I get a chance to photo it. Basically the bottom of the hood where the hinges attach ripped off the hood (I still have those pieces) and there is minor damage to the top side that would require some fiberglass matting repair.
Like I said, I haven't made a final decision, but I can still take pics for you. If weather forecast stays the same I should actually be able to mess with the car next weekend some.
stealthee
03-04-2015, 08:15 PM
I'll just leave this here
http://i239.photobucket.com/albums/ff92/stealthee3k/IMG_20150304_190807_419_zpsussybxry.jpg (http://s239.photobucket.com/user/stealthee3k/media/IMG_20150304_190807_419_zpsussybxry.jpg.html)
:)
CoreyB
03-05-2015, 08:58 AM
Those look barely used at all, nice score.
green-lantern
03-05-2015, 10:33 AM
Sweet!
MDoe8
03-05-2015, 03:54 PM
I love sohc builds
stealthee
06-08-2015, 02:06 PM
So I have been trying to get myself moving on the car and it seems like every time I want to do it it looks like it is going to start raining at any minute. Well, sun was out this morning so I went out and put the battery on charge. After charging a little bit I tried to start and it cranked over nice and fast but it didn't fire.
I pulled the coil wire to check spark and had good strong spark, so I figured the fuel just needed to prime, even though I thought I could smell fuel. When I put the coil wire back on it sputtered for a second then kept cranking. I pulled the coil wire again and just cranked the hell out of it for 10 seconds and put the coil wire back on. Once back on I had it running in about 30 seconds.
I took a quick vid and, yes, it still looks like shit, but at this point I figure whatever. The car is really loud because it has no downpipe and is exiting straight out the manifolds.
http://youtu.be/kFnygdX2Vz8
After I took the vid I moved it for the first time since last year. Once it warmed up the idle stayed right around 800 rpm. Not bad for sitting for so long.
stealthee
06-08-2015, 03:53 PM
Of course the day I get motivated enough to mess with it and move it it actually does end up raining. When the rain started I was actually about to do a quick hand wash on it to knock all the heavy dirt off and I was going to degrease the engine bay so I have a starting point there.
Looking at the forecast I might be at a standstill for the next few days now. :(
CoopKill
06-08-2015, 04:47 PM
You didn't kill the trans moving it di you??/ :suspect:
stealthee
06-08-2015, 05:11 PM
Trans is already borked. The only way I could bork it anymore is if it would assplode.
stealthee
06-13-2015, 06:47 PM
A bad case of poison ivy has completely derailed any progress. Went and got a steroid shot and prednisone prescription today today to hopefully help out in the recovery. Once cleared up I plan to start tearing it apart.
A bad case of poison ivy has completely derailed any progress. Went and got a steroid shot and prednisone prescription today today to hopefully help out in the recovery. Once cleared up I plan to start tearing it apart.
Good luck w/that, Brian.
Never had to deal with it, seem to have some sort of resistance.
Now I'll prolly fall in a big fucking patch of it, soon just to test that assumption. :rolleyes:
stealthee
06-21-2015, 08:51 AM
Well, Brian hasn't been able to sleep tonight, so Brian has been doing lots of thinking and planning. And yes Brian is talking in the 3rd person, mainly due to exhaustion. LOL Also due to that exhaust it appears I have rambled on for a bit.
Anyway, I think I am going to go ahead and get the engine and trans pulled as soon as I can. I either need to get 2 sheets of plywood, and get my uncle to bring me the hoist and do it in my driveway, or I can chance driving it to my uncle's house (only 2 miles away, but with zero exhaust it will be a loud 2 miles), then we can try to tow it back to my house once the drive train is pulled.
Once drive train is pulled I'll hopefully be able to salvage one trans out of the two I have. For the engine, the heads are probably going to need pulled either way, since I am almost certain the head gaskets are my main source of my oil leaks. At that point I think I am just going to replace the vss and call them good. I'll replace the rear main seal, oil pump and pump pick up so I can use my 94 oil pan that isn't jacked up.
In my randomness and sporadicness, while I was typing this I started searching for prices on head gaskets. Lo and behold I found an entire upper end gasket kit for $68. It comes with head gaskets, valve cover gaskets, intake manifold gaskets, exhaust manifold gaskets, cams shaft gaskets, viton valve seals, head bolts, and other random gaskets and o-rings.
It is my hope that with that $68 for the top end gaskets, plus the ~$15 for rear main seal, and ~$230 for oil pump and pick up I can technically have the car drivable. I will swap the ECU and harness while the drive train is out to the Fed Spec one I have, and bolt the headers onto the engine before the drivetrain goes back in.
The only other thing I want to do before the drive train goes back in is to clean the engine bay really well and get a 1/4 of paint to paint the bay. If the car is drivable it will open my options up immensely in the completion of the body work.
So basically, after all my (possibly incoherent) rambling I basically came to the conclusion that for under $400 I could have the car drivable. I could do enough to the body to make it presentable at that point until it gets a full on paint job.
stealthee
06-23-2015, 12:56 AM
So, today got a little more set in motion. I got a ride to go get two sheets of 22/32 OSB so I can get the drivetrain pulled.
I'm going to get everything ready to come out then have my hoist brought to the house and pull it. Once out the transmission will be unhooked and I'll get the engine bolted to the stand to start tear down.
Also, I forgot some components in my initial estimate. I wasn't thinking about the timing stuff and water pump. That additional stuff puts me in the $500 range, but still at that point I have something workable.
Once the heads are off I'll take a look at the cylinder walls. If they look like they need attention then I will probably go ahead and do bearings and rings, and hone the walls, but I would like to avoid tearing it down that far if I can. We'll see when I get to that point though.
AhAMaY115
06-23-2015, 04:13 PM
Keep it up man! It's good to hear that your getting your car going again.
Mine's been down since '08 and I've been slowly gathering parts, but the motivation comes and goes. It's been helpful seeing you make progress!
Keep it going!
stealthee
06-23-2015, 07:15 PM
Mother Nature went and pissed me off today. My goal of the day was to get my shed rearranged so I can use it easier once the engine is on the stand. I was making very good progress and probably only had an hour worth of work left until I could consider the shed ready. Well, Mother Nature decided it was a good time for a torrential downpour. I had stuff all over the place in my madness of trying to organize, so I had to basically start throwing stuff back in the shed to get it, and to try to get myself out of the weather.
Since everything had to be tossed back in I am guessing I now have about 2 hours to now have the shed ready. Once it's ready tear down will begin. I'm not sure how much I would be able to get done tomorrow due to having to attend an unemployment program at 1:00, but hopefully I have cooperative weather and can at least have the shed ready tomorrow. My goal after that is to have the drive train pulled and engine on the stand by the weekend.
stealthee
06-23-2015, 11:06 PM
I got tired of arguing with myself and went ahead and spent some money today. I ordered the 120k kit with an oil pump. I ordered the top end gasket kit and head bolt kit. Lastly I ordered a new flywheel, rear main seal, oil pickup, and 6 spark plugs.
The only other thing I "should" need for reassembly is a clutch disk (as long as I find my ACT pressure plate) and fluids.
Beef6
06-24-2015, 07:42 AM
Love hearing any progress on the bastard! Now just get it done so we can have a PA mini meet at some point haha
stealthee
06-24-2015, 10:44 PM
I'd be down for a mini-meet, even if I have to bring the Pontiac. LOL
Weather was absolutely gorgeous today. After all my running and crap I had to do I got home around 5:00 and decided to focus on getting the shed finished.
http://i239.photobucket.com/albums/ff92/stealthee3k/20150624_202052_zpsx9i21r6u.jpg (http://s239.photobucket.com/user/stealthee3k/media/20150624_202052_zpsx9i21r6u.jpg.html)
I think I can work in there. I even thought about taking my stack of wheels and making a "bench" to work on. Worst case scenario my uncle told me we could load the engine up and take it up the road to his house and use the garage.
I even started the car so I could move it for a minute. Unless something changes in the next few days that will be the last time it runs under its own power until everything goes back in. There are some storms forecasted to roll in mid afternoon so I should be able to get able to get a good amount accomplished before that. I am still aiming to have the drivetrain pulled by the end of the weekend.
stealthee
06-25-2015, 08:27 PM
The weatherman is a damn dirty liar, and because of that I got nothing done to the car today.
Since I wasn't able to get anything done I took a ride into town and went ahead and picked up some hardware so I can bolt the engine to the stand. Also picked up some Purple Power and Brake Clean so I can degrease the engine well once it's out.
The flywheel, spark plugs, rear main seal, and oil pump pick up should be here tomorrow. The upper gasket kit is supposed to be here Tuesday. The 120k kit hit a small snag. I got an email and apparently they are out of the water pumps and have no timetable on when they will come in, so I am having them process the order minus the water pump and refund me the difference. If it goes out tomorrow I should have it by Tuesday or Wednesday.
I don't have a solid timetable on when everything will be set to go back in. I need to make a final decision on the color code I am going with so I can get at least a quart to paint the engine bay and some engine components before everything goes back in. It's definitely going to be blue again, I just can't decide on which blue. LOL
Street_Chally73
06-25-2015, 10:42 PM
The meteorologists have been messing with me, too, Brian. Keep the momentum going! I'm nearly there now, too, but am waiting for a low humidity day to get more powder coating & beadblasting done.
The meteorologists have been messing with me, too, Brian. Keep the momentum going! I'm nearly there now, too, but am waiting for a low humidity day to get more powder coating & beadblasting done.
I have a baseball bat, just need a meteorologist...:mad:
stealthee
06-26-2015, 03:06 PM
The meteorologists have been messing with me, too, Brian. Keep the momentum going! I'm nearly there now, too, but am waiting for a low humidity day to get more powder coating & beadblasting done.
You wouldn't be interested in powder coating some NA calipers would you? :suspect:
Street_Chally73
06-26-2015, 11:01 PM
You wouldn't be interested in powder coating some NA calipers would you? :suspect:
Greg would probably be your best option there...I have yet to rebuild my spare calipers, so I wouldn't want to tackle someone else's until I feel confident I did a quality rebuild.
stealthee
06-27-2015, 12:06 AM
LOL, I have rebuild kits in one of my shopping carts since I am not 100% sure what I want to do just yet.
I made a lot of progress today.
http://www.3sgto.org/members/stealthee-albums-revival-picture8025-dscn0349.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8027-dscn0351.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8031-dscn0352.jpg
As you can see body parts have started to come off. Unfortunately I found that my driver's fender that I thought I was going to use is unusable. Apparently dirt/mud had gotten behind the side skirt and rotted the bottom of the fender pretty badly. Fortunately I have a driver's fender that should be usable
In the process of removing panels a few bolts broke, which I figured was going to happen. Some of the bolts are unseen and I will likely just use large self-tapping screws in their place. The others I will likely just drill out. I also found that I am probably going to have to do a patch panel on the driver's floor pan. There is one part that is very thin. Thankfully it looks to be contained to just the one area. For as long as the car has sat it could have been much worse.
When I went to remove the side skirts I had another little surprise too. Apparently I had bottomed out on something, because both pinch welds were folded over at various points. With a little bit of effort I got both sides straightened out. I'll probably put a little more time into them a little later.
Body panel removal wasn't the only thing I got done. Engine harness is unplugged and laying loose in the engine bay. Upper intake manifold, throttle body, intake tube and MAS are removed. Radiator, rad hoses, heater hoses are all removed. Fuel lines are unhooked and laying loose. Battery tray and washer tank are removed. Line to the slave cylinder is undone. Power steering lines are undone. Oil is drained.
I think all that is left to do to pull the drive train is pulling the axles and unbolting motor mounts. Weather dependent they could be out tomorrow.
I finished the night by putting the tools away, slapping the hood back on and putting on a car cover I bought earlier this week.
http://www.3sgto.org/members/stealthee-albums-revival-picture8032-dscn0353.jpg
Oh yea, earlier while I was working on the car a kid in a work van stopped and was talking to me about it. He asked me if I'd sell it. LOL He proceeded to tell me he lives up the road and that he has wanted my car since the first time he saw it. Then he asked me what it was. LMAO While we were talking UPS showed up with goodies. New flywheel, spark plugs, oil pump pickup, and rear main seal will go into a pile until they are ready to be bolted to the engine. More goodies should be coming next week.
stealthee
06-27-2015, 10:00 PM
Due to that bitch Mother Nature no real progress was made today. Only thing I got accomplished was getting the axles pulled.
I did also got the hoist brought down to the house so I am all set to pull the drive train as soon as weather permits. With the way the forecast looks that should be Monday.
CoopKill
06-27-2015, 10:50 PM
:p
http://lmgcorporate.com/kptv/weather/ibs_web_7-day.jpg
stealthee
06-27-2015, 10:57 PM
Apparently we took all your rain. LOL
stealthee
06-29-2015, 10:28 PM
http://www.3sgto.org/members/stealthee-albums-revival-picture8110-dscn0354.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8111-dscn0355.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8112-dscn0356.jpg
Sorry about the washed out look of the pics. The sun was very bright. As you can see, though, I made a little bit of progress today. Unfortunately it was about the only progress I made. I had one nut on the driver's mount that fought me to the end and I had to "go around it" to get the drive train out. If you look at the last pic the drivers mount is still in the car. LOL Once everything was finally pulled I had to take a break, because the sun was getting to me and I hadn't eaten anything.
After about 2 hours I was finally able to get back to the car, but after a short time my mom called me and I had to stop and get cleaned up to go help her in her purchase of a car. It started to rain as I was putting tools away anyway.
So yeah, technically not much got done today, but it is another step in the right direction. Got another part in the mail too. Matt, sublime-whatigo, sold me an AC bracket for a great price. Now I can see about putting AC back on the car to make summer driving more enjoyable. :)
CoopKill
06-29-2015, 11:04 PM
Gitter!
stealthee
06-30-2015, 11:08 PM
Well, there's your problem
http://www.3sgto.org/members/stealthee-albums-revival-picture8113-dscn0357.jpg
As figured found a nice hole in the bell housing.
And got the engine bolted to the stand.
http://www.3sgto.org/members/stealthee-albums-revival-picture8115-dscn0359.jpg
Unfortunately, little else got accomplished today due to other duties.
Funny story, though. My uncle and cousin stopped by to see how things were progressing and I partially uncovered the car to pop the hood. A younger guy rode by on a motorbike as we were looking at things and he almost wiped out rubbernecking at the car. LOL
FedEx brought my top end gasket kit today. Still waiting on the 120k stuff.
Lastly, I got a nice little piece of mail today. My one credit card is going to be interest free on all purchases starting tomorrow until next July, so looks like I am going to go ahead and make a few purchases I was going to put off for awhile.
stealthee
07-13-2015, 11:38 PM
Well, its been two weeks since my last update. Between going out of town for 4 days, preparing to go out of town for 4 days, recovering from being out of town for 4 days, and a little bit of laziness yesterday was the first day I touched anything in that time period.
Anyway, between yesterday and today progress has been made. Took the timing covers off and snapped a pic just to rub it how simple the SOHC timing set up is. :p
http://www.3sgto.org/members/stealthee-albums-revival-picture8153-20150712-171956.jpg
Took the timing belt off and gave it a squeeze. I think it was a little dry and was in definite need of replacement.
http://www.3sgto.org/members/stealthee-albums-revival-picture8154-20150712-173105.jpg
Got the valve covers off and heads actually look pretty clean, although there is a slight color variation between the front head and the rear head with the rear head looking "cleaner". Anyone have an explanation for that?
Front head
http://www.3sgto.org/members/stealthee-albums-revival-picture8155-20150712-183153.jpg
Rear head
http://www.3sgto.org/members/stealthee-albums-revival-picture8156-20150712-183215.jpg
So anyway, in the midst of teardown yesterday I found out that in Mitsubishi's infinite wisdom that that did not put a hex section on the SOHC cams. After standing there bewildered for a few minutes I came in the house to look online to see if I was missing something. I found in the manual I needed "special tool MB990767" to hold the cam gear, so I could break it loose.
After cussing at Mitsubishi for several minutes, I spent a lot of (probably too much) time trying to figure out something to be able to break the cam gear bolt loose, but was unsuccessful. At that point I called it a night, got cleaned up, and took a ride to my uncle's to BS and borrow his battery powered impact.
Went out this afternoon to get back to work. Impact made quick work of the cam gear bolts and I continued with tear down. While working I see FedEx pull in. I had no idea what they were bringing me today until I looked at the label and saw Maximal Performance. I just placed the order on Thursday and it showed up Monday. Terry rocks.
Oh, this is what was in the box
http://www.3sgto.org/members/stealthee-albums-revival-picture8157-20150713-145339.jpg
I went with a 2100 this time. I still had the 2600 pressure plate, but decided with all my trans and clutch issues, and with me not planning on doing anymore racing the 2100 would still be plenty.
Anyway, pulled the heads and the cylinder walls look great. Engine has 120k on it and there is still a nice crosshatch. Valves have a little bit of carbon, but otherwise look good. Plan on cleaning them up and putting in new valve seals while it is apart. I noticed the majority of my oil leakage appeared to be from the front head, and around the oil pump. Rear of the engine was still pretty clean. When I popped the oil pump off I noticed something peculiar. It appears the outer case has a small crack in it starting at one of the bolt holes. I have a new oil pump coming anyway, but I just thought that was odd.
So to finish off this long-winded post I did some degreasing of the block, and some of the brackets. I reorganized some of my tools and some of the parts and called it a night.
http://www.3sgto.org/members/stealthee-albums-revival-picture8158-20150713-181341.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8159-20150713-181352.jpg
stealthee
07-14-2015, 10:46 PM
No pictures for today's update. I didn't do a lot, but I got a lot accomplished. Gathered up a few random brackets and the heads and ran them to my uncle's. I used the parts washer and cleaned everything up. I went ahead and cleaned the gasket surfaces up while I was at it too.
Plans now are to do valve seals on Saturday. At that point the heads will be ready to go back on the block. Also Saturday I plan on sandblasting brackets and other random parts and pieces and putting a few coats of engine paint on them in prep for reassembly.
Oil pump should be here tomorrow, water pump should be here Thursday. Only thing I am waiting on now is the oil pump gasket, and hopefully that is here next week. Once I have everything reassembly can commence and I will be one step closer to getting the Bastard back on the road.
stealthee
07-16-2015, 12:19 AM
No progress today due to helping my cousin try to figure his Civic out, but I do have one picture.
Some goodies showed up today.
http://www.3sgto.org/members/stealthee-albums-revival-picture8165-20150715-230529.jpg
Brand new OEM oil pump and a Gates water pump. The oil pump will allow me to go back to my old non beat up oil pan. It may have brought up a small hurdle at the same time, but tomorrow I will get back under the hood and do a little more research to confirm my suspicions.
Tomorrow my main goal is to get my yard mowed. After that I will probably do a little more parts cleaning here and there and go get some blasting sand in prep for sand blasting this weekend. I may start getting the engine harness ready to come out if I feel up to it after mowing.
Also, my uncle said he should be free tomorrow evening and we can probably get the valve seals and valve lapping done. That will be one step closer for engine reassembly.
stealthee
07-19-2015, 12:28 AM
So I waited a few days for the next update.
Thursday evening my uncle called me and I went over there to work on the heads. Got the valve spring compressor set up and went at it. As I pulled each valve out I cleaned the carbon off while my uncle pulled the VSS and put the new one in place. Lapped each valve before cleaning all the valve grind compound then reinstalled the springs and keepers. Didn't take long at all, but we only did the rear head. My uncle was in no hurry and I wasn't going to rush him since he was helping me.
So I went home and decided to tackle the God forsaken nut that held me up on removing the engine. After a little over an hour starting with a nut splitter, breaking said nut splitter, and using a hammer and chisel I finally got the nut off. I had a total of about 3 hours into this damn thing
http://www.3sgto.org/members/stealthee-albums-revival-picture8174-dscn0436.jpg
I called it a night after that victory and started fresh on Friday. Before I even got started the mail lady brought me some more goodies.
http://www.3sgto.org/members/stealthee-albums-revival-picture8175-dscn0437.jpg
I got a later start on the car than I wanted so I didn't get a ton accomplished other than some engine bay clean up and removal of a few more parts in the bay. I called it a night and got cleaned up to go out. I left the car looking like this.
http://www.3sgto.org/members/stealthee-albums-revival-picture8176-dscn0438.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8177-dscn0439.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8179-dscn0440.jpg
So I was getting ready to start on the car today when my uncle called me about doing the other head. I went over and we got started on it. Was making progress getting it done when my cousin pointed something out. Lo and behold there was a random nut jammed in one of the oil returns. I theorize now that maybe that is why the front head was "dirtier" than the rear. It took a little bit of force to pop it out from the underside, but we got it out and finished the head.
The nut in question..
http://www.3sgto.org/members/stealthee-albums-revival-picture8178-dscn0441.jpg
So after getting the second head done I headed home and decided to spend more time in the engine bay. Removed some more crap, degreased some more, and called it a night.
http://www.3sgto.org/members/stealthee-albums-revival-picture8182-dscn0445.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8181-dscn0444.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8180-dscn0443.jpg
I think tomorrow I might remove the subframe connectors to get the final bit of grease and grime off them and go ahead and get some paint on them. The last thing I need to remove from the bay before I paint it is the engine harness, but I think I want to wait to remove it until the day I am ready to paint, so I don't leave a gaping hole in the firewall for critters to get into. I might go ahead and remove the main subframe piece at that time too to make it a little easy to get body color on the lower part of the firewall. It will allow me to get the backside of the subframe cleaned up and some paint on it as well, but I don't want to remove it in case I have to roll the car out of the way.
That's it for this update.
Beef6
07-19-2015, 08:39 AM
Looking good Brian! Any plans or thoughts to tackling the body work, changing anything up?
stealthee
07-19-2015, 11:53 AM
My goal right now is to get the engine bay finished up so I can get some paint in it. Also I can start some of the reassembly on the engine since the heads are done. I still need to tear the trans apart too, but wanted to get the engine done first. Anyway, once the bay is painted I can go about reinstalling the drivetrain and at that point the car can be driven under its own power.
Only changes occurring is going to 2g 3000GT rear bumper cover and going with a slightly different blue. I need to go to the paint supply store and get a price for the color I want to get pricing before I make my final decision. The only real "bodywork" that needs done is around the antenna where the paint bubbled up and had some rust. I've got fenders and the driver's door sitting here.
I am still waffling on getting new headlight buckets. The passenger bucket isn't in the greatest shape from the PO hitting a deer. I don't know if he didn't have full coverage, or if the repair shop just cheaped out on the repair, but it was basically hammered back into place. The side headlight mount is also gone and there are a bolt or two broke off in it. The drivers side has the side headlight mount broken, and a few bolts broken off in it. It's just money I am trying not to spend, hence the waffling.
Anyway, I still need to pull the trigger to get the 99 bumper and stuff coming, but I'm waiting to get the bay and the engine under control since I really don't have the storage space. Hell my other 99 bumper is sitting outside my shed. I need to list it for sale for like $50 for someone interested in fixing it. I mean, I could fix it, but feel I'm just better off getting new and calling it a day.
My real goal at this point is to have the bay and all the jams painted, have the engine and transmission in and have the car drivable by fall weather. That means I still need to get brakes sorted and stuff. I don't know if I'll be able to get the car painted by the time winter hits and if I don't its not a big deal. If I can get it in paint by next spring I will consider this project a victory.
Beef6
07-19-2015, 03:03 PM
Sounds like a good plan to me, Has to feel good to see progress after all this time. Is your current 99 bumper that bad or you just don't feel like dealing with it?
stealthee
07-19-2015, 04:38 PM
A little bit of both. I'll snap some pictures a little later.
green-lantern
07-19-2015, 04:52 PM
Brian, you ever think about going DOHC? Sorry if I've asked that already lol.
stealthee
07-19-2015, 04:59 PM
Only way I will swap is if it is a TT swap. The power difference between SOHC and DOHC NA is miniscule and not worth the swap.
stealthee
07-19-2015, 07:28 PM
Here are the pics of the bumper cover
Other than the obvious paint issues it doesn't look bad from the front.
http://www.3sgto.org/members/stealthee-albums-revival-picture8183-dscn0451.jpg
Move to the left corner and issues start appearing
http://www.3sgto.org/members/stealthee-albums-revival-picture8185-dscn0453.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8184-dscn0452.jpg
On the right underside this is the damage
http://www.3sgto.org/members/stealthee-albums-revival-picture8186-dscn0454.jpg
On the topside the piece that mounts to the rad support and to the right headlight bucket are broke off flush
http://www.3sgto.org/members/stealthee-albums-revival-picture8187-dscn0455.jpg
All of the damage could be repaired. The only real "visible" damage is the left side, and again, with some finesse it could be almost perfect, but I just feel like I am better off getting new. If someone wants it as it sits they could have it for $50. LOL
green-lantern
07-19-2015, 11:25 PM
Only way I will swap is if it is a TT swap. The power difference between SOHC and DOHC NA is miniscule and not worth the swap.
180 to 220 seems worth it to me.
stealthee
07-20-2015, 12:05 AM
more like 180 to 210....
But anyway, I'd have to get engine, harness, ECU, etc to swap. I need same basic things to TT swap.....
Beef6
07-20-2015, 07:37 AM
Yeah its probably easier just replacing that bumper, they are so cheap new its not worth the hassle.
Sounds like you should just TT Swap it then...:glee2:
stealthee
07-20-2015, 11:50 PM
Nothing major accomplished today. My brain was in random mode so I was bouncing from project to project. I did some more degreasing and cleaning under the hood. Pulled the wiper arms so I didn't forget them when I sandblast and paint the other brackets.
To pull the rear wiper arm I had to remove the spoiler. Since I had to take it off I figured I could do a test fit...
http://www.3sgto.org/members/stealthee-albums-revival-picture8190-dscn0457.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8189-dscn0456.jpg
And with the 96
http://www.3sgto.org/members/stealthee-albums-revival-picture8192-dscn0459.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8191-dscn0458.jpg
All in all I like the look of the duck tail by itself. Adding the 96 spoiler makes it too much IMO. I think I am going to stick with just the 96. The additional work to attach the ducktail just isn't worth it to me at this time. I'll probably just try to sell it to help the project along.
In order to keep critters and water out of the car I grabbed an extra body plug and popped it in the hole left by the wiper motor and bolted the wing back on.
I gathered up all the parts that need sandblasted and put them together. The only other things I need to gather now is the front subframe crossmembers, cause they are still bolted to the car.
Hopefully tomorrow the Tractor Supply store has the sand in stock and I can pick up two bags and hopefully get to blasting some stuff later this week and maybe paint some things by this weekend. I also plan on stopping by the paint shop and get a price on paint and supplies. I'll weigh my options and maybe go ahead and get 1/2 gallon to get me started, so I can at least get the bay done and get it ready for the engine to go back in.
On that note, I still need to finish cleaning up the block and put a few coats of engine paint on it. I am only waiting on a few gaskets now so I can completely reassemble the engine. That may be another project that I can complete by the end of the week. Only thing I won't bolt on is the headers and that is only because they will end up being in my way while it is on the stand since they are long tubes.
I'm done rambling now. LOL
green-lantern
07-21-2015, 04:25 PM
I like the ducktail a lot. Your right or I agree anyway, it's too much with the banana. I'd prefer to have the ducktail than the banana but I've never been a big fan of the nanner anyway. The 96 is the best looking one IMHO though.
2fnloud
07-21-2015, 05:52 PM
Glad I got to see this, I thought about that combo, but thought I wouldn't like it, seeing it....I thought right.
stealthee
07-21-2015, 06:15 PM
I like the ducktail a lot. Your right or I agree anyway, it's too much with the banana. I'd prefer to have the ducktail than the banana but I've never been a big fan of the nanner anyway. The 96 is the best looking one IMHO though.
I am about 50/50 on which I like better, but the work involved in adding the ducktail is the deciding factor for me at this time.
If you're interested I'd give you a good deal on the ducktail. I know it goes for $175 + shipping new. I'd sell it for $75 plus shipping. I'd have to come up with another box regardless, because the original box ended up falling apart.
If you're not interested, I'll post up in the classifieds and probably on Craigslist.
green-lantern
07-21-2015, 06:48 PM
I am about 50/50 on which I like better, but the work involved in adding the ducktail is the deciding factor for me at this time.
If you're interested I'd give you a good deal on the ducktail. I know it goes for $175 + shipping new. I'd sell it for $75 plus shipping. I'd have to come up with another box regardless, because the original box ended up falling apart.
If you're not interested, I'll post up in the classifieds and probably on Craigslist.
That's actually pretty freaking tempting. I like the ducktail on the Stealths better but I'm tempted to get it for later projects or just let it sit on the shelf with other parts I should have sold years ago. lol
stealthee
07-22-2015, 10:22 PM
Buy it Paul, BUY IT!
So, no actual progress to report. My niece and nephew were around yesterday so I didn't get anything at all done then. Today, I had to get my yard mowed, then do some running, but I did get 100 pounds of blasting sand purchased. Also bought a heavy sanding disk to run over my main subframe so I can get it ready for paint.
Hoping to maybe get the subframe cleaned up and painted tomorrow and maybe get the blasting done on the other parts.
The only thing I didn't get done today that I wanted to was to stop at the paint store and get pricing. As soon as I have that I can game plan for getting the paint laid down in the bay and getting it ready for the engine to go back in.
stealthee
07-23-2015, 11:56 PM
So no pics (yet), but I got a ton of brackets and stuff sandblasted today. I went through 2 50lb bags of sand and started on a 3rd before I quit. I need to go buy another 2 bags tomorrow (1 for myself and 1 to replace the bag I started using that belonged to my uncle) so I can go back over some parts I went easy on to save sand, and take a few more parts over to blast.
I'm hoping I can get a larger diameter tip for the blaster because the one he got with it plugs up with anything over a fine grain. If I can get at least medium grain sand through it then it should make work go faster and not use as much sand. The other issue is the compressor just has a hard time keeping up, but you'll have that.
Once I have everything I want done blasted I'll take some pics to add to the thread.
Street_Chally73
07-24-2015, 05:29 AM
Brian, I'm not sure if you're doing some sort of reclaiming of the media, but I've had great success placing a 10'x10' tarp down then blasting on top of that...It's saved me many bags of black beauty & glass beads in the past. ;)
Just a suggestion if you want to save some cash with the media.
stealthee
07-24-2015, 10:51 AM
I had suggested reclamation of the media to my uncle and he was against it because he didn't think it would be worth the trouble and didn't want to put material that had been blasted off back through the blaster. :shrug: He's hard headed though, and since he's nice enough to let me use the blaster I'm not going to argue with him. :lol:
Street_Chally73
07-24-2015, 11:27 PM
Buy an eBay special syphon gun...Mine's been going strong for three years now running reclaimed media. ;P
stealthee
07-25-2015, 12:20 AM
LOL
The vast majority of my sandblasting is done. I'm going to be blowing sand out of my nose for weeks LOL
I didn't get to snap any pics of my parts pile that was blasted, but I figure it will be better to take pics once I go to paint them anyway.
I did get the crossmembers pulled today. Damn, I forgot how much overkill of bolts were put into those. It didn't help it was hot as hell when I was pulling them, but I got them out, cleaned what I had missed while they were still bolted in, and loaded them up in the Pontiac's trunk.
Probably won't get much done tomorrow, but hope to paint some brackets and such on Sunday, maybe.
stealthee
07-29-2015, 09:16 PM
Well, its been miserable since my last update. Heat and humidity have made me lazy as hell. Also, I spent the entire day Saturday on detailing the Grand Prix and at a car show. After the show some cousins came over and we hung out by the fire and drank beer. Lots of it. Not sure what time I went to bed Sunday morning, but whatever time it was it ruined me for the rest of the day. LOL
I decided to go to the shed last night and try to get some cleaning done on the block and get it taped off so I could get ready to get it painted. That sort of backfired on me. While I was working on cleaning up the block a random storm rolled in and it started pouring rain. I was running around trying to get a comforter I had out air drying put away as well as other things when I realized my box of parts that was sandblasted was getting soaked as well. I was so pissed at that point I just called it a day and closed up the shed.
Of all days for me to decide to get motivated again it had to be today, the hottest day of the year. I opened the shed door and was immediately disgusted. Surface rust was on almost all the parts I already sandblasted. I took a paint/rust remover disk and went to town on the subframe crossmembers to get them recleaned up I had to work for so long then take a break because the heat was just miserable. I finally got the crossmembers clean and ready for paint. Got some primer on first then broke for lunch.
Went back out and started applying paint and realized between the temperature and the fact that the pieces were sitting in the sun the paint was starting to go on dry so I had to relocate my paint area. While I let the pieces cool I put some time into the engine again. Put some time into the oil pan too. Took a break, and painted, and cleaned, and took a break and so on.
To wrap up a story that is already longer than it needs to be
http://www.3sgto.org/members/stealthee-albums-revival-picture8230-dscn0462.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8229-dscn0461.jpg
I'm not entirely sure why it looks like a red streak up the side of the block. Almost looks like rust, but I assure it is clean.
I did order a few more things such are some bushings for the front end, as well as found a great deal at a local powdercoater for my brakes.
I need to make a run for some other supplies tomorrow and hopefully get a price on paint, and if it isn't crazy get at least enough paint and supplies for the bay so I can get it readied for the engine to go back in. I do have everything I need now to reassemble most of the engine. I need to just finish cleaning up the gasket surfaces and start bolting things back on.
I did order new lash adjusters from Ninja. I can still put the heads back on and just wait until the adjusters soak in oil a day or so to install them.
Its slow progress, but its progress.
stealthee
07-30-2015, 09:20 PM
Nothing done directly to the car today, though I did get something for it.
http://www.3sgto.org/members/stealthee-albums-revival-picture8235-dscn0463.jpg
I got a quart (plus reducer) ready to spray. That should be plenty to do the bay, jams etc.
Tomorrow will try to get the LCA's and brake calipers removed so I can blast them this weekend. At that point I will either start sanding the bay or finish cleaning gasket surfaces on the engine so I can start reassembly of it.
stealthee
07-31-2015, 07:42 PM
USPS brought me more goodies today
http://www.3sgto.org/members/stealthee-albums-revival-picture8239-dscn0464.jpg
Thanks to GZP and Ninja for shipping quick. I put my lash adjusters in oil to soak. They'll be ready to go in as soon as I am ready to install them.
Got a little more work done to the car today
http://www.3sgto.org/members/stealthee-albums-revival-picture8240-dscn0465.jpg
http://www.3sgto.org/members/stealthee-albums-revival-picture8241-dscn0466.jpg
Both front brakes removed as well as LCA's. In the process of removing the passenger side LCA (the first one I removed) this happened
http://www.3sgto.org/members/stealthee-albums-revival-picture8242-dscn0468.jpg
Split my friggin lip open. Was spitting lots of blood for awhile. Thankfully didn't break any teeth.
As to how it happened, the bolt that goes through the rear bracket and the subframe was being very bitchy. I was lying on my back, pulling with the extra force required to spin it when the ratchet slipped off and smashed me in the face.
Saw a little start, and gave me an instant headache, but I pulled through. After I got the blood under control I finished removing that bolt, got the LCA out and moved to the other side.
Didn't get as much done today as I wanted to, but between busting my lip, and forgetting I had plans to go out with friends tonight I got done what I could. Hopefully tomorrow I'll get the rear calipers off and I think I am going to go ahead and remove the whole k-member since its only a few more bolts at this point.
CoopKill
07-31-2015, 09:21 PM
I have the same bushing kit, let meknow how the install goes.
And, sorry, but Bwahahahahaha! :beaten:
stealthee
08-01-2015, 08:27 PM
Went out last night so I slept in today. Woke up to find USPS made yet another delivery
http://www.3sgto.org/members/stealthee-albums-revival-picture8248-dscn0469.jpg
She's probably starting to get pissed at having to stop at my house so much LOL Anyway, I have everything I need now to rebuild the entire front suspension. I got started on the car and started by removing the rear brakes and rotors. At that point I started to remove the K member. I probably should have made it easier on myself by removing the rack and the sway bar first, but it wasn't all that heavy in the end.
Once out I pulled the sway bar and the rack. I had been debating it, but it looks like I will be going ahead and replacing the rack while it it all out. Both inner tie rod boots are torn and as far as I know it is the original rack with 195k miles. At that point, I decided to go ahead and remove the stock sub frame bushings. Unfortunately for me they didn't come out as easy as just smacking them out with a hammer. The rear ones IIRC came out without an extreme amount of effort but the front ones required some effort and ingenuity. After hitting the one with a 4 lb sledge for way too long I fashioned a ball joint press of sorts with a C clamp and large socket. Once I was able to break it free with that one quick shot with the hammer knocked it out.
I moved to the other front one and wasn't as lucky. There is a lip of some sort that wouldn't let me get the C clamp on square so it kept rolling off. While I was messing with it my uncle stopped in to see how things were going and he tried to help me but it still wasn't working. He suggested I just burn the bushing out, which I eventually did.
The front cross member was a bitch too. Used the C clamp on the first one but the second one refused to come out so I burnt it out too. The thing that sucks about that is I already had nice shiny paint on it. Oh well though, I'll give it a quick scuff and put another coat or two on it once I put the other bushings in.
Since I fought the bushings so much I really didn't get much else done. I did make a realization that I am probably going to need to drop the rear subframe at some point and clean it up because it has lots of surface rust on it. Its not something I am going to take on right now because I can still drive the car with it like that if I have to. I might make that a project later on once the body is ready to go.
This is how she sits now.
http://www.3sgto.org/members/stealthee-albums-revival-picture8250-dscn0471.jpg
I figure I will just wait to put the K member back in until after the bay is painted. One less thing to paint around.
stealthee
08-02-2015, 09:28 PM
No pictures today. Today was a low motivation day. I was up way too late, so I slept way too late, then ended up watching the Pirates game.
So anyway, I got the ball joints out of the LCA's. Came out easier than I thought. I then used my "homemade ball joint press" set up to help in removal of the front LCA bushings. The first one came out rather easy after I started it with the c-clamp, the 2nd one however fought me to the end.
I got the sway bar links cut off. One was still attached to an LCA while the other still attached to the sway bar.
For the rest of the time outside I cleaned as much grime off the k-frame, LCAs and sway bar as I could. Its weird that sandblasting will remove paint and even rust pretty easily, however it doesn't like to remove grease and grime. :shrug:
I've now got a stack of parts ready to be blasted, as well as some of the other smaller parts that I have to reblast since they got wet and surface rusted. I want to get them blasted and painted, then I will more forward with engine reassembly and engine bay paint.
MDoe8
08-03-2015, 02:42 PM
good work so far!
stealthee
08-03-2015, 04:35 PM
good work so far!
Thanks. All you guys watching this thread and the interest in progress is part of what is keeping me going.
I got everything else blasted today that needs to be done for now. I want to start getting primer on stuff, but it looks like it is going to storm so I might be SOL for right now.
If all else fails I can at least try to take the pistons out of the calipers and finish getting them ready for powder coat.
futurevr4man
08-04-2015, 01:48 PM
Thanks. All you guys watching this thread and the interest in progress is part of what is keeping me going.
I got everything else blasted today that needs to be done for now. I want to start getting primer on stuff, but it looks like it is going to storm so I might be SOL for right now.
If all else fails I can at least try to take the pistons out of the calipers and finish getting them ready for powder coat.
Post up how difficult that is to do. It's on my list.
stealthee
08-04-2015, 02:23 PM
Gnate, I have watched a few videos on caliper "deconstruction." Most people use an air compressor with a blow gun in the hole where the hose screws into and put air in until the piston blows out. They'll usually use the outside pad or a small piece of wood where the outside pad would go to stop the piston(s) from shooting across the room.
I didn't get anything else done yesterday due to the looming weather (that never happened until like 10pm.) No progress today either. I promised my cousin I'd help him work on his girlfriend's car. Now I guess I have to go to the county fair. I had no intention of going, but my aunt bought a ticket for me, without me knowing.
stealthee
08-05-2015, 10:53 PM
Today was a productive day
http://www.3sgto.org/members/stealthee-albums-revival-picture8254-dscn0473.jpg
The picture is hard to see what all is there because the table top is covered in overspray, but there is the subframe, LCAs, LCA brackets. motor mounts, motor mount brackets, and brake booster.
Not only did I get all those parts and pieces primered and painted, but I also got the gasket surfaces on the block ready to go as well as cleaned up the piston tops as good as I could.
I have a small amount of small parts that I plan on getting painted tomorrow and that should be the last of pieces I have to paint with a rattle can (for now)
In between coats I plan on starting to bolt things back to the block. I actually need to try to hang the block by the hoist again so I can get the rear main seal changed. Once its changed and I have the oil pump and pickup on I can get the pan back on.
I'm excited about starting to bolt things back on for two reasons. #1 is because obviously it means I am making progress. #2 is because I am running out of room and once stuff is bolted back on I will gain that room back. :lol:
Oh I also managed to get one front and one rear brake caliper apart also. I ended up screwing a male threaded and female threaded air nipples together, then just plugged it into the air line and pressed the other end into the hole where the brake line screws into. It pressurized the pistons and popped them out.
The pistons are in suprisingly good shape where it matters. I can already tell I am going to have a blast tying to get the dust boot and retainer back in place once I get the calipers back from powder coat.
I still need to get the other two apart. I don't know if the pistons are just froze or what. I need to either try another way to get the air to stay in the caliper, or worst case I could try to fill them with a grease gun to get them to pop out.
stealthee
08-07-2015, 10:23 PM
Got nothing done yesterday, due to rain all day. Oh well, it let me get some other things done in the house.
Today was a different story. First thing I did was ran to the hydraulic shop I used to work for and got an adapter to go from a brake line to a air coupler. As soon as I hooked it to the other front caliper it blew one piston out, but the other remained in place. I sprayed a little WD in there and let it set, repositioned the other piston to hold in the air and fed air back to to it. I saw the other piston move slightly so I smacked the caliper with a hammer and it popped free.
The other rear caliper I was not so lucky on. I actually started smashing the caliper itself from hitting it so hard trying to free the stuck piston. That's one thing I am going to have to replace now.
I also got all sort of smaller brackets and random things painted.
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8261-dscn0475.jpg
I undid the engine from the stand, hung it from the hoist and changed the rear main seal, then rebolted the engine back to the stand. After that I managed to get the heads, oil pump, oil pickup, oil filter housing and oil pan all bolted to the block.
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8262-dscn0476.jpg
I found something else out though that I wasn't accounting for. The crank sprocket for the 96+ SOHC has a timing blade on it since the 96+ use a crank sensor. As you may recall I went back with a 91-95 oil pump so I could use my old oil pan. The 91-95 oil pump can't accommodate the timing blade so I am either going to have to figure out how to get the timing blade off the crank sprocket or get a 91-95 sprocket. Another thing I noted anyway was I think TDC is marked differently between the years so I might be further ahead in getting another sprocket anyway.
I finished the night by putting everything away. I set the lower intake in place and set the valve covers on the heads to keep stuff out. After I took the pic I threw some tape across the lower intake to definitely make sure I don't drop anything in there. LOL
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8263-dscn0477.jpg
Tomorrow is a day with no certain goal. I do want to bolt a few more things to the block (cams, mounting brackets, water pump, etc) and until I found out about the crank sprocket I was hoping to get the timing belt done tomorrow, but that is out now. Basically. anything I get done tomorrow will be a success.
Jimvr4
08-08-2015, 02:56 AM
Looking good Brian!
stealthee
08-08-2015, 11:50 PM
Thanks Jim.
Unfortunately no pics today. First thing I did was went back over the head bolts to make sure torque was good. After that I pulled the old lash adjusters out of the rocker assemblies and put the new ones in. I changed the gasket that I call the cam cap on both cams and changed the cam seal on the front cam, then bolted the assemblies in place and torqued to spec. The rear cams cam seal is actually in the distributor housing on the SOHC so I pulled the old cam seal out then went to install the new one. I actually set it in too far and in my attempts to remove it, I effed it up. :grumblegrumblegrumble:
Anyway, got the front and rear motor mount brackets and tranny stays bolted into place. In doing that I noticed something on the rear bank. I grabbed the OBX headers I bought off of Kevin out of the car and went to test fit and the rear header didn't want to clear the bracket. To make a long story short, I figured out I had to remove the exhaust studs on 4 and 6 and the header falls right into place.
I had intentions on getting much more done, but at 3:00 I got a phone call that my mom had fallen and possibly broken her wrist. At that point I had to put everything away, get cleaned up and go run her to Med Express. Med Express did an xray, confirmed it was broken, then basically splinted her and said she had to go to the ER. Once the ER did yet another xray they said she had to be admitted and they will be doing surgery tomorrow. Oh what fun.
After dropping her at the ER I ran to Advance and got another cam seal. After she was told she was being admitted she asked me to run home and get some stuff for her. On my way home the wheel bearing noise the Pontiac has been making seemed to get worse. I decided to jack it up and check and am glad I did. There was A LOT of play in the right rear bearing, so I went ahead and yanked it out and called my uncle to give me a ride to my brothers so I could get my mom's car.
Stopped at Advance, again, and exchanged the bearing since it was under warranty. Stopped at Taco Bell and grabbed some food since I hadn't eaten all day. Went back to the hospital and they still hadn't gotten her admitted to a room yet. Finally around 8 they said they had a room ready, but it wasn't til 820 that they came to take her to the room. Finally got out of there at that point and headed home.
Not sure what will get done tomorrow. I need to put the Grand Prix back together then I might try to get a few more things on the engine at that point, but with not knowing what time her surgery is and when she will be discharged it's hard to game plan at this point.
stealthee
08-09-2015, 08:46 PM
Not much achieved today. I put the new wheel bearing in the Grand Prix... twice. I bolted it in and realized I forgot to put the dust shield back in, so I had to take it back out and put it back in once the shield was in place. I also managed to "fix" a head shield that was hanging. I also found where I had an exhaust leak.
For the Stealth all I managed to get done was bolting the water pump on and hopefully for the last time put the water crossover pipe in place. My aunt called me and told me to come join them for lunch, so I stopped there and went for food. After that I ended up helping my cousin do some work to his Civic.
After that got the call that my mom was being released from the hospital so I had to get cleaned up and go get her.
By the time I got home there was no point in digging stuff out and starting on anything. Hopefully tomorrow I can get a few more things done then I might start on getting the engine bay sanded so I can get it prepped for primer and paint.
stealthee
08-10-2015, 09:39 PM
Not a lot accomplished today due to playing chauffeur for my mom. She drives bad enough with both arms, I'd really hate so see how she would drive with only one good one. :lol:
I did manage to get a few more things cleaned up and bolted on the engine. Got the spark plugs gapped to .040 and installed. I also found out the lower intake gaskets in the kit I got are total junk and the upper intake gasket doesn't even fit so I just ordered a Felpro kit from Advance and it will be in tomorrow.
Its starting to look almost complete. Sorry for the dark pics. I was running out of light fast and didn't realize they came out as dark as they did.
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8269-dscn0479.jpg
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8270-dscn0480.jpg
Some of the stuff bolted on is only on finger tight at the moment. I will bolt on the lower intake tomorrow once I have the gasket. I intend on hydro dipping the upper intake so it wont be bolted on right away. The valve covers are just sitting on there. I need to finish making sure they are clean and sand them up. My plan is to paint them body color.
As soon as I get my hands on a 91-95 SOHC crank timing cog I will be able to set the timing belt and put the distributor back on and at that point the engine will be basically ready to go back in. :)
Goals are going to be hard to set over the next several days due to weather and my mom's injury. As said, she can't drive for the time being so I am likely to be her main mode of transportation should she have to go anywhere. I guess its supposed to storm tomorrow, but I was thinking I could set up a temp bench in the basement and try to tear into my transmissions to get that ready to go. We will see how it goes.
stealthee
08-11-2015, 10:23 PM
Picked up intake manifold gasket kit today. Also stopped at paint supply store and got some clarification on my primer and picked up some reducer while I was there.
Only spent about 2 hours messing with stuff this evening due to doing some running around and spending some time at my brother's.
LIM in bolted in, but needs torqued down. Going to replace the upper and lower orings on the injectors that I just ordered from Ninja. Once I have those I'll install the fuel rails. Cleaned up and painted the cam gears, even though you can't see them under the timing covers. LOL They are bolted on, but not torqued down. I'll end up having to borrow an impact to torque them down.
These are basically the same pics I posted last night, except now you can see better and the cam gears are on.
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8278-dscn0482.jpg
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8279-dscn0483.jpg
Also I went ahead and took the angle grinder with the paint/rust remover wheel to the frame rail to clean it up. I also went ahead and removed the firewall shield because I realized how much of a nightmare it was going to be to tape around it for paint. After going over the rust and getting it cleaned up I just grabbed some rattle can primer to put a coat on the affected area.
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8277-dscn0481.jpg
Again, goals are hard to set at this point. I am at a stand still on the engine until I get a crank sprocket. I still need to get the transmissions apart, but I think tomorrow I want to try to get the engine/ECU harness out so it is yet another thing I don't have to worry about right now. Will probably pull the front coilovers and with that steering knuckles so I can clean them up and so that I won't have to tape them off when it comes time to paint the bay.
My fingers are crossed that I can get the bay in at least primer this weekend. If I could get the bay painted I will be giddy as hell. :)
stealthee
08-13-2015, 12:36 AM
Today seemed to be semi-productive. Since I am at a standstill on the engine I figured I would move forward on the engine bay prep for paint. I started by getting the interior removed so I could get the engine/ECU harness removed. Pulled both front seats, but snapped one of the front studs on the driver's seat. I guess I'll end up having to drill it out and tap it and use a bolt because the floor pan is double paneled where the stud is.
Anyway, set the seats outside the car and pulled the carpet back so I could get access to the panel that covers the harness on the floorboard. Pulled the ECU and got the random plugs unhooked. There is one plug near the vent on the far passenger side that I couldn't reach. For some reason I thought I had to pull the vent to access the plug, and I thought the vent came out easy... I was wrong. I ended up breaking the vent. I ended up pulling the glove box to get access to the plug.
Anyway, got the harness pulled and out of my way and started realizing I could easily get some other stuff on the firewall out of my way. Proportioning valve, brake lines, and brake master are out of the way. I removed a few of the nuts holding the fuel lines and rear brake lines so they can drop out of the way. A few random brackets and bolts I had left there were removed. I crawled back in the car to remove the shift cables. After getting them out I crawl out of the car to stretch my aching back and I see this.
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8305-dscn0486.jpg
I may have mentioned it before, but this kitten likes to come visit me if I am outside in the evening. He curled up in my passenger seat and was there for a good amount of time. LOL
Also got the coilovers and knuckles pulled and out of the way.
When I was done for the night I was left with this
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8306-dscn0487.jpg
Ran the angle grinder back to my uncle and was talking about my progress and he went ahead and grabbed the primer gun for me to use. Weather forecast looks good for tomorrow, so as long as I can get the rest of the bay scuffed up I should be able to put a few coats of primer on the rust and bare spots, then go back over the entire this with it mixed as a sealer.
If I can manage to get that done I'll probably wait until Saturday or Sunday and scuff it again and lay the paint and clear in the bay. At that point I'll wait at least a few days to start bolting things back in.
stealthee
08-13-2015, 11:20 PM
Today did not go as planned at all.
Slept longer than I intended, then I needed to get a few chores done in the house. After that I went to go to the shed to get some tools and realized I locked the damn key in the shed last night. Thankfully, I was able to break in without breaking anything or cutting the lock. I took the water separator I was given and figured out what I needed to put it on the compressor then went out to get supplies.
Picked up some pipe fittings (got them for free actually :)), stopped at the dollar store and got a gallon of Simple Green (actually Mean Green) and a small tote so I could soak some parts to get them clean. A big thanks to Gonzo for posting the thread he did. Stopped at hardware store and got a paint mixing cup, then I stopped at my uncles to swap the air coupler that I forget to swap before I took the angle grinder back.
Finally got back to the house and drained the compressor so I could put the water separator on, got it on and finally got started on the car. Sanding just seemed to take forever. As I found bubbled paint or rust I used the stripper wheel to do the work. Went ahead and pulled the clutch master, and a few more random things. Went to remove the radiator isolators and the one on the passenger side popped right out, but the drivers side one was STUCK. I ended up destroying it to get it out.
Also went to remove the wiper assembly since paint was cracking around the bolts that hold it in place and broke two of the bolts on the driver side. Was taking a break and heard the compressor running, and then run again, so I knew something was wrong. Went to check it out and the drain on the water separator I just put on was leaking. I drained the compressor again and unscrewed the canister so I could look at the drain and found the drain was borked. I tried to come up with a solution, but was unsuccessful so I had to remove the separator and just go straight back to the hose.
Also, somewhere along the line today I banged my elbow and its all knotted up and sore now.
Anyway I think the vast majority of the sanding in the bay is DONE. I went and borrowed a DA so I can feather out a few areas that are a little rough, then wait a few days to scuff everything again really quick, wipe it down, then apply color and clear.
It's hard to tell the difference in this pic compared to the pic I posted yesterday, but there is progress, just not the progress I wanted today.
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8307-dscn0488.jpg
stealthee
08-15-2015, 12:13 AM
Day started well. Got up at a good time, got some breakfast and got set up to get some stuff done. Got the DA to work and did lots with it. Smoothed out some stuff that I couldn't get smooth by hand. Once I had the bay where I wanted it I grabbed a bucket of soap and water and wiped everything down and hosed it clean.
I took one last pic of the bay, before it was all one color
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8309-dscn0490.jpg
Since I plan on painting the valve covers and intake pipe body color I grabbed them out of the Mean Green solution and wiped them down, hosed them off, then went on to sand them down. Once I was happy with the sanding on those I cleaned them with the soapy water, rinsed them, and set them in the sun to dry.
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8308-dscn0489.jpg
At this point it was getting close to 85* and the sun was beating on the car so I didn't want to try to spray primer on scorching hot metal so I took a break. After some lunch I went ahead and taped off the windshield and mirrors to prevent overspray. Also put some tape on the heater core ends and the steering shaft to make cleanup easier there.
Finally late in the evening the car was out of the direct sunlight so I was ready to spray. I have only ever sprayed with a spray gun once, and that was many years ago with my dad at my side so I was a little scared at first, but once I got going my fears eased.
When I was done for the night I was left with this
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8311-dscn0493.jpg
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8310-dscn0491.jpg
My plan is to let the primer set up over a few days, then go back over it and lightly scuff everything again before I spray the color and clear. After what I learned today I think I am going to scuff the primer on Monday, get it all cleaned up and wiped down, then wait until Tuesday morning to spray so it has all day to set up.
My goal for tomorrow is to organize the shed, because everything is in my way. Only other car stuff I might do is try to get the bushings in, which I planned on already having done, but got sidetracked on other stuff. LOL
I need a break from working on the car for a day or so. One day next week, though will be transmission day. Hopefully, by then I will have my crank sprocket and a few other things and can be ready to drop the engine back in by next weekend possibly.
stealthee
08-17-2015, 10:55 PM
The heat today was BAD! I didn't manage to get done what I wanted to get done, but I did get some things out of my way.
Got the front LCA's put back together. New Moog ball joints, new Whiteline front bushings, and the new Whiteline rear bushings will go on when I bolt it on. The ball joint install took way longer than I would have liked. The c-clip refused to go in at first. After a few different attempts at a few different methods I finally figured out what I needed to go to get them in place and had both done in minutes after that.
Also installed 3swarehouse front subframe bushing kit into the K member and the front cross member.
I had planned on sanding the engine bay today in prep for painting tomorrow morning, but it looks like rain all day tomorrow, and possibly the next two days. The rain sucks for me making progress on the car, but it is much needed.
Made a phone call and I will be picking up a reman rack tomorrow. Plan to get tie rod ends at that time too, and will probably have to order the sway bar links.
Ordered a set of sway bar bushings and a Ralliart rad cap from Ninja. Really didn't need the rad cap, but if I didn't add something to my order it was going to cost me $6 for shipping. Since I added the $10 cap, I got free shipping, so its like I paid $4 for the cap. LOL
Also ordered new couplers and a new air filter for my intake.
alexw3000gt
08-21-2015, 12:36 AM
This thread is tits.
stealthee
08-21-2015, 01:20 AM
Thanks Alex.
Haven't made a ton of progress over the past few days. I did spend too much money though. LOL
Picked up the steering rack on Tuesday. New silicone couplers showed up Wednesday. Sway bar bushings and Ralliart rad cap showed up today (Thursday.)
Still on the way are a new crank sprocket found on eBay. Also found a NOS lower timing cover on eBay. Just tracked them and they both should be here tomorrow.
Also have a braided steel clutch line coming from a 240SX. It will allow me to go straight from the hardline at the firewall connection to the slave, instead of through my rigged up hardline from where I deleted the clutch damper.
Also on the way are new axle seals and my new air filter.
My main goal is to make sure I have the bay all resanded tomorrow and prepped for paint on Saturday. I did already start sanding the bay the other day, but for some reason it is really hard to tell what is sanded and what isn't. I also need to sand the valve covers and intake arm so they are ready for color as well.
If I can get paint and clear on Saturday morning without any issues I'll start on the transmission Saturday morning and hopefully finish up by Sunday.
Then, I figure Monday I will start bolting subframe, cross members, LCA's, etc back in. Maybe Tuesday I will see about bolting things to the firewall and framerails and try to get the harness back in. Then Wednesday I can maybe try to get the engine and trans back in. All goals are dependent on weather and other situations of course though.
stealthee
08-21-2015, 01:50 AM
Forgot to add I have a bunch of used parts coming from Josh Mitoska as well.
I've now ordered from Mitoska, Ninja, 3sx, Maximal, IPS/Fabberge, and 3swarehouse.
I also figured that the majority of my big purchases should be done for now. I do have brake rebuild kits and new ebrake shoes in my Advance auto shopping cart, and will probably add a ebrake hardware kit from another online vendor and be around $100 there. I do still need to get the bumper cover, turns, and all that fun stuff, but am thinking I am going to put that off until it is closer time to actually paint the car. Worst case if driving the car becomes a necessity I can put the busted 99 bumper back on until then.
TwoXist
08-21-2015, 02:47 AM
I wish I had the time, space and knowledge to do this with my car.
alexw3000gt
08-21-2015, 09:33 AM
I know the feels, I've been impulse buying used parts left and right as I find good deals popping up. Some things I need, some I don't yet... like the ARC2 setup I just picked up off of Bill ha
I've been getting almost all of the stuff I've needed from 3SX, which is odd because back in the day I avoided them like the plague. With the free shipping now, they seem to have some of the best prices on stuff shockingly.
stealthee
08-22-2015, 12:32 AM
Crank gear and lower timing cover came in today. Got timing set in about 5 minutes, and that was two tries, LOL
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8317-dscn0496.jpg
Did I mention I love simplicity?
Got a few other things cleaned up and painted. and got the engine most of the way assembled now
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8318-dscn0497.jpg
Need to finish cleaning up the power steering pump before I put it on. Also want to see if I can disassemble the alternator so I can get it nice and clean too before it goes back on.
Other than that plans were deviated from for the day. Got a call about possibly going back to work so I had to make some calls and do some running. Then I ended up helping my cousin on out his Civic. Thankfully we aren't still in the garage working on R&R of the head for a head gasket change.
I still hope to get color in the bay tomorrow. All depends on how things go though. If not tomorrow definitely Sunday.
stealthee
08-23-2015, 01:07 PM
Well, due to a homicide investigation basically right in front of my house for most of the morning yesterday I didn't get hardly anything done yesterday.
Long story short, crazy bitch from next house over stabs her boyfriend. Boyfriend runs to my neighbor's place across the road from me for help. Boyfriend dies on neighbors porch.
I woke up sometime after 4am to my bedroom being completely lit up with flashing lights from the ambulances and cop cars on scene. I walked out to talk to some officers on scene once I realized there was a body covered up on the neighbors porch, I got the information I needed and answered a few questions they had, then went back in and tried to go back to sleep. I woke back up at 10am and there was about 8-10 cop cars in parked in the road in front of my house, parked in my driveway, parked everywhere. They didn't roll out of here until around noon or so.
I wasn't about to go out messing with the car until the cops were gone, so obviously I didn't manage to get much done. I tried to get my tie rods lined up on the rack where the old ones were, but obviously will have to recheck alignment once everything is back in the car. I went ahead and bolted the rack and the sway bar to the K-member.
I got the power steering pump all cleaned up and it is reinstalled.
Really didn't manage to get much else done. I stopped early due to having plans to go to the dirt track.
Motivation is lacking today, but my main goal is to go over the engine bay and make sure it is ready for paint. Sand the valve covers and intake arm so they are ready for paint. Try to get the alternator as clean as I can get it and get it installed on the engine as well.
If everything goes to plan, and if the weather is gonna play nice, I should hopefully be able to have paint in the bay tomorrow.
I need to get as much done as I can over the next week because as of this moment it looks like I am going back to work next Monday. I will still have evenings, while it is still nice, and weekends, but obviously progress will slow.
stealthee
08-23-2015, 10:51 PM
So, thanks to additional drama from the homicide victim's family and the family of the "suspect" up the road I didn't get started as early as I wanted to today. When I finally did get started the 9 was within my reach in the shed...
Anyway, spent some time cleaning up alternator which was very oily, dirty, and nasty. Took a good bit of time. Decided to go ahead and put a light coat of paint on it since I couldn't get it evenly clean. I also spent some time cleaning up the tensioner/idler pulley since it had a lot of surface rust on it. I put it in some ATF for awhile to make sure the bearing was good to go.
While I was in the middle of stuff my neighbor stopped by to talk about the events of the last 40 hours, and ended up chewing my ear for about an hour.
Did I ever mention how much I HATE doing stuff twice? Well, long story short, I went to put the rear lift bracket back on, which is also the top mounting point for the alternator. I was trying to remember how the bracket mounted and when I figured it out I realized something.... there was no way to put that bracket on with the timing belt on. The bracket bolts in behind the timing belt backing plate.
I took off the motor mount, crank pulley, and timing covers. I loosened the timing tensioner and took the belt off. Grabbed my strap wrench, held the cam gear, broke the bolt loose, and took the cam gear off. Took the bolts for the backing plate out and bolted the bracket in place. After that I put everything back together, bolted the alternator up, put the tensioner/idler on, and called it a night.
That means I did not get the sanding done that I wanted to get done, which means I probably won't get color in the bay tomorrow, unless the weather forecast has changed for Tuesday and beyond. Going to have to play everything by ear for the next several days.
The current state of the engine
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8319-dscn0498.jpg
Beef6
08-24-2015, 08:07 AM
Don't your employers know you have a car to build? This is no time to go back to work Brian!
stealthee
08-24-2015, 10:52 AM
LOL Josh. I am coming into the stretch now where body work will be the main target point. I expected things to slow down at that point anyway, especially considering I still need to buy bumper cover, lower door trims, splash shields, etc. It will all work out in the end. Besides, I wanna pay my credit card down a little before I go buying that stuff.
stealthee
08-24-2015, 11:08 PM
Didn't do a lot today, but I got done what I wanted to get done. Bay is sanded. Valve covers are sanded. Intake is sanded. Forecast looks perfect for tomorrow so once I am up and moving the plan is to wipe the bay, valve covers, and intake down with reducer to make sure they are clean. Set up the horses for the valve covers and intake. Tape off the windshield and mirrors. Mix up a tiny bit of sealer and reseal a few areas I sanded through. Clean the gun out. Put a few coats of paint on everything. Clean the gun out again. Put a few coats of clear on everything.
If it all goes to plan tomorrow I will probably try do transmission on Wednesday, start bolting K-frame and suspension pieces in on Thursday, start bolting brackets and such back on on Friday, and if I can get the hoist back and get the help engine and trans back in on Saturday. Not sure on getting engine and trans in on Saturday though due to a bunch of other stuff going on this weekend. If not as soon as I can get a 2nd set of hands it will go back in.
stealthee
08-25-2015, 07:55 PM
Woke up this morning to an awesome 65* temperature. Checked the forecast and it looked perfect. Got moving around and after a bowl of cereal and brushing my teeth went outside to get started. Pulled the cover off the car and wiped everything down with reducer.
Mixed up some sealer and spot sealed some areas. Cleaned the gun up and prepped for color
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8320-dscn0500.jpg
Started spraying the color and as I got the hang of things it was looking pretty good. I thought I was going to have enough to do the jams and stuff too, but I ended up using everything I had on the bay, valve covers, and intake arm.
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8321-dscn0501.jpg
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8322-dscn0502.jpg
Once I ran the gun out of color I cleaned it up yet again and mixed up the clear.
Started spraying and right away knew something was wrong. I was getting a textured look. I tried making a few adjustments to the gun, and to my technique, and it was making no difference. I called my uncle to see if he could stop down to see what the hell was going on, but my aunt had his truck so he threw some ideas my way. I called my brother, hoping he could help, but he said it's been so long since he sprayed he really didn't know, but also offered some suggestions.
About the time I get off the phone with my brother my uncle pulled in. He checked out what I had going on, suggested an adjustment in PSI, took the gun and sprayed an area and it looked awesome.
Come to find out the wind was being my enemy and I needed to slow my pace as well as spray closer, as well as the increase in PSI.
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8323-dscn0503.jpg
http://www.3sgto.org/members/stealthee-albums-revival-2-picture8324-dscn0504.jpg
I still ended up with some orange peel, due to my earlier issues, and fighting with the wind that decided to wait to pick up until I started spraying. LOL I figure you won't even see 90% of the bay once everything is bolted back in, and the flat areas on top that are visible I can always go back and buff them out.
Tomorrow, I have an "interview" at 9, so I will probably be back and start on the transmission tomorrow afternoon. Hopefully it all goes well.
I will start bolting k-member and suspension stuff back up and things back in the bay Thursday. Unless something changes I probably WON'T get the engine and trans back in this weekend. Just too much going on, but hopefully by next weekend it will be in.
Beef6
08-25-2015, 10:10 PM
Looks great! I regret not respraying my engine bay while the engine was out for 2 or so years, looks so bad and would have been so easy at the time.
stealthee
08-25-2015, 10:28 PM
Thanks Josh. I don't know if I would say "easy" though. LOL I went WAY further than I ever anticipated going when I started with this aspect of it. Putting everything back is going to be nightmarish. LOL
Beef6
08-26-2015, 07:46 AM
Well by "Easy" I mean easier than pulling the motor again just to paint now. I'm sure it easy by any means getting it that stripped and painted.
stealthee
08-27-2015, 12:25 AM
Well today's update is no update. I did check out the paint to see how it is curing and it looks alright. I think I'm going to try to buff the more visible areas under the hood just to make them pop a little more when the hood is up. If buffing doesn't work I might do a wet sand and try to lay down another coat of clear.
Updates are going to definitely slow now. I got all the paperwork taken care of for work today and actually got called in this afternoon because they needed my help right away. I was hoping not to go back til Monday so I could get a few things knocked out over the next few days, but I'm back in the workforce so I guess I can't complain. I'll get done what I can get done, when I can get it done.
Glad to hear you're back in the workforce, Brian. :)
I imagine they put the crazy bitch in stir; how many other ones are there in your neighborhood?
Maybe you need more upscale surroundings...:wink:
stealthee
08-27-2015, 03:45 PM
If i had more upscale surroundings then I probably couldn't paint my enginebay in my driveway. LOL
alexw3000gt
08-27-2015, 06:43 PM
I resprayed a stealth in my apartment parking lot.
They threatened to tow it while it was sitting there sanded down, but once I got paint on they shut up ha
Beef6
09-18-2015, 07:19 AM
:boring: ....
stealthee
09-18-2015, 10:28 AM
Yeah, I know. Between going back to work and the weather progress has completely halted. I was also assisting my cousins on their cars, to get them running again. I need to a thing or two done to the Grand Prix, then hopefully I can spend some time on the Stealth and get some things done this weekend.
stealthee
01-11-2016, 10:04 PM
Well, its obviously been awhile since the last update, and that is because there has been no progress. There probably won't be any real progress for a few months at least due to winter setting in. I do want to try to get the trans situated though. That I can take over to my uncle's and work in his garage. He keeps telling me he'll come get it in his truck, but I just haven't done so yet.
There are other little things I can try to make progress on while the weather is colder like rebuilding the calipers (once I get them powdercoated), but again, I just have get and stay motivated to do it. If I can manage to get a few little things done while it is cold it can give me a stack of things to do once the weather warms.
I'll hit my 90 days next. I have been promised a raise at 90 days and have hopes it will be decent just from things the GM has said to me. That alone will help immensely as it will take a financial burden off me and I won't be as worried about spending money on the car.
CoopKill
01-11-2016, 11:04 PM
Come help with mine!
stealthee
01-11-2016, 11:13 PM
You mean MINE? LOL
J said you were working on it again, thats awesome Brian!
I wasnt sure if you still had it or not.
He came over the other day and we messed around with mine for a few hours.
Got everything pretty much off, ready to pull the block....and see what carnage awaits inside. maybe this weekend.
stealthee
01-14-2016, 06:11 PM
Yeah, I went up one night and he and I pissed with the drag car for a few hours, eliminating wiring, and BSing. He told me about your car. Just look at it this way. Its an excuse to build it bigger and badder. :lol:
Mine will ride again some day.
Well me and J pulled the motor and found a piston was upside down. Must have been why it wasnt running right...
Head seems okay, a few minor nicks and dings, but nothing that is not fixable.
I didnt get a picture, but the turbine wheel was actually just fine. I was expecting to see it totally thrashed.
http://i243.photobucket.com/albums/ff194/Derf7667/20160116_165414_zps2o8nkw2q.jpg (http://s243.photobucket.com/user/Derf7667/media/20160116_165414_zps2o8nkw2q.jpg.html)
http://i243.photobucket.com/albums/ff194/Derf7667/20160116_165426_zpsnfzx3sfz.jpg (http://s243.photobucket.com/user/Derf7667/media/20160116_165426_zpsnfzx3sfz.jpg.html)
sohcstealth
01-19-2016, 12:23 PM
Well me and J pulled the motor and found a piston was upside down. Must have been why it wasnt running right...
Head seems okay, a few minor nicks and dings, but nothing that is not fixable.
I didnt get a picture, but the turbine wheel was actually just fine. I was expecting to see it totally thrashed.
http://i243.photobucket.com/albums/ff194/Derf7667/20160116_165414_zps2o8nkw2q.jpg (http://s243.photobucket.com/user/Derf7667/media/20160116_165414_zps2o8nkw2q.jpg.html)
http://i243.photobucket.com/albums/ff194/Derf7667/20160116_165426_zpsnfzx3sfz.jpg (http://s243.photobucket.com/user/Derf7667/media/20160116_165426_zpsnfzx3sfz.jpg.html)
Ohhhh! :eek: That's not good!
futurevr4man
01-19-2016, 01:09 PM
Cylinder walls look great! They'll buff right out!
stealthee
01-19-2016, 06:11 PM
Damn Nate. Now that you said it and posted the pic I remember J telling me about it being flipped. Insane there wasn't more damage.
Haha i know.
We were pretty shocked at all the more visible damage done with as many pieces there are in the pan lol
We did find some small pieces in just about each cylinder.
What started the mystery was when i took my intake off last summer to dive into it to see what happened, i found piston chunks and ring pieces in the upper plenum and throttle body and a smashed #3 plug.
Just getting around to it now and actually giving a damn to work on it.
Anyone need a cheap 2-bolt block that needs sleeved HA!
toddrs93
01-27-2016, 05:02 PM
Well today's update is no update. I did check out the paint to see how it is curing and it looks alright. I think I'm going to try to buff the more visible areas under the hood just to make them pop a little more when the hood is up. If buffing doesn't work I might do a wet sand and try to lay down another coat of clear.
Updates are going to definitely slow now. I got all the paperwork taken care of for work today and actually got called in this afternoon because they needed my help right away. I was hoping not to go back til Monday so I could get a few things knocked out over the next few days, but I'm back in the workforce so I guess I can't complain. I'll get done what I can get done, when I can get it done.
I don't know if you mentioned a target completion date or not but this would be awesome to have it debut at ECG this year.
Beef6
06-29-2016, 01:44 PM
Just dropping by...
stealthee
06-29-2016, 03:02 PM
Haha. Well, I have an easy up canopy at my disposal now so maybe that will motivate me to move forward on the project.
DocWalt
06-29-2016, 09:20 PM
Get to work, Brian.
Chris@Rvengeperformance
06-30-2016, 02:14 PM
Going to work on it before Jesus comes again?:devilish:
Greg E
07-01-2016, 02:10 PM
I built a car from scratch faster than you have been reviving this thing. Get to work before I come over there and motivate you.
stealthee
07-01-2016, 09:33 PM
Do it. I got beer and two Taco Bells within 10 miles. :lol:
OhioSpyderman
07-01-2016, 09:46 PM
Do it. I got beer and two Taco Bells within 10 miles. :lol:
Mmmmmmmmm.....Beer
Beef6
11-01-2016, 07:24 AM
Just popping in to say...where's the progress!!
Chris@Rvengeperformance
11-01-2016, 11:07 AM
4 months until thread is 4 years old
stealthee
11-01-2016, 05:17 PM
Yeah, I know. My drive has faltered. Every time I seemed to get the motivation to do something I got called away to help someone else.
I actually was looking at portable garages online the other day. I think that is the only way I will get seriously motivated to finish it at this point.
AdamVR4
11-02-2016, 09:52 PM
Yeah, I know. My drive has faltered. Every time I seemed to get the motivation to do something I got called away to help someone else.
Reason numero uno I don't wrench on other people's crap anymore. Screw that. Hole-up and give yours some of that TLC ;)
stealthee
11-02-2016, 10:13 PM
I know I'm too nice. It usually one of my two cousins and lately a few times my brother. All are capable of doing stuff on their own, but they like to have me around for my knowledge. I really need to call on them to help me, not necessarily do what needs done, but keep me working.
Honestly my biggest fear now is putting everything back in the engine bay. I took some pics for reference, but unfortunately my HD crashed last year and I lost all those pics. I need to get that stuff figured out, get the engine harness put in, get the transmission sorted, then I could at least drop the engine and trans in at that point. After that most of the stuff left should be cosmetic.
AdamVR4
11-02-2016, 10:19 PM
I know I'm too nice. It usually one of my two cousins and lately a few times my brother. All are capable of doing stuff on their own, but they like to have me around for my knowledge. I really need to call on them to help me, not necessarily do what needs done, but keep me working.
Honestly my biggest fear now is putting everything back in the engine bay. I took some pics for reference, but unfortunately my HD crashed last year and I lost all those pics. I need to get that stuff figured out, get the engine harness put in, get the transmission sorted, then I could at least drop the engine and trans in at that point. After that most of the stuff left should be cosmetic.
What sort of reference pics do you need? I bet we can help if your can make a list :)
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.