PDA

View Full Version : Spring upgrade project - "Smoke em up!"



Toni
03-21-2013, 04:35 PM
So this turned into a general build thread. Lots of upgrades/pics throughout the thread.


So this Spring it's all about launching and a few other goodies as well. My goal is to have it all ready by 4/20 (see what I did there?).

Mods:

Broomfield Billet Tcase
300m output shaft
New clutch
New friction pads on the rps fly

Will also be doing some other things while I am there. Some new synchros, fix mystery oil leak, rod bearing check, etc.

Right now I have the tranny out and waiting for some more parts and the tcase is off to Pampena to get the billet case fitted.

https://dl.dropbox.com/u/29716828/rt/IMG_20130316_185300.jpg

-Antoni

green-lantern
03-21-2013, 04:40 PM
Are you going with Dave's TC?

Blackmount
03-21-2013, 04:49 PM
Nice! I would like to build up my drivetrain at somepoint too to handle my abuse.

Toni
03-21-2013, 04:52 PM
Are you going with Dave's TC?

Yup! It's one nice piece!

AdamVR4
03-21-2013, 05:00 PM
Love it. Stock rear axles for now?

Toni
03-21-2013, 05:07 PM
Love it. Stock rear axles for now?

For now I'll probably see how they hold up. I might pick up a spare stock one if I decide to go to a track that is far away.

green-lantern
03-21-2013, 06:53 PM
Yup! It's one nice piece!

Damn right

somebody told me he quit selling them.

J-Groove
03-22-2013, 11:17 AM
Subbed for more updates.

Love your car Toni!

-John

AdamVR4
03-22-2013, 11:57 AM
Pampena brace in your bell housing? (Don't worry too badly if you don't do this... I still haven't)

Toni
03-22-2013, 12:27 PM
No brace. Gonna cross my fingers on that one too lol. I do have a spare 5 speed so if the housing goes hopefully there will be minimal damage to internals and I can just swap it. I actually didn't think it was an issue on 5 speeds?

Hard AttacK
03-23-2013, 11:18 PM
So this Spring it's all about launching and a few other goodies as well. My goal is to have it all ready by 4/20 (see what I did there?)

-Antoni

i c wut u did there

Toni
03-30-2013, 08:37 PM
Well not much to report. Waiting for parts, rebuilt flywheel, and build tcase to come in. In the meantime I checked/changed the rod bearings because I was pulling the pan anyway to install an oil temp sensor bung. After two dyno session, countless trips down the strip, road course, autocross, and generally beating the crap out of it there is no signs of wear! Great news, means I have a good solid tune going right now.

IPD
03-30-2013, 09:36 PM
awesome! and congrats on being COTM for apparently january, february, march, and possibly april.

Toni
03-31-2013, 09:37 PM
Thanks! lol.

Got the tranny cracked open and ready for parts!

http://primaryboost.com/store/rt/drivetrain0313/DSC_1700.JPG

Toni
04-07-2013, 10:50 PM
Soooo this drivetrain upgrade turned into a buy a ton of parts upgrade lol. Doing new struts and a few other goodies that I'll keep to myself for now :)

http://primaryboost.com/store/rt/drivetrain0313/DSC_1735.JPG

AdamVR4
04-08-2013, 01:01 PM
New OEM struts? I miss mine.

Toni
04-08-2013, 01:14 PM
Yup. Factory ECS. Maybe I'm the only one but I love them lol. Why do you miss them?

AdamVR4
04-08-2013, 01:20 PM
Yup. Factory ECS. Maybe I'm the only one but I love them lol. Why do you miss them?

Like everyone else, I'm tired of stiff coilovers.

Toni
04-08-2013, 03:10 PM
I ride on tour mode on my factory setup most of the time. I figure since sport mode on stock is annoying unless I'm having fun then I won't like anything stiffer.

Blackmount
04-08-2013, 04:56 PM
Yes even I got tired of coilovers, S-techs + ECS. done.

DrGonzo
04-08-2013, 05:50 PM
I have always loved my ECS struts. I loved them even more with the custom ECS Controller that Duke built: 3000gt/Stealth ECS Controllers (http://www.renegadetechworks.com/)

Toni
04-10-2013, 07:55 PM
More progress...

Replaced the battery tie stud, installed the front struts, replaced the front cam end caps, and reinstalled the cover with a new gasket.

http://primaryboost.com/store/rt/springupgrade13/DSC_1739.JPG

http://primaryboost.com/store/rt/springupgrade13/DSC_1740.JPG

http://primaryboost.com/store/rt/springupgrade13/DSC_1741.JPG

Gotta do the rears still. Not sure why they were leaking, used new caps during the rebuild.

Not sure if anyone saw on fb but I didn't clean my rims before storage and the brake/rotor dust fused and rusted to the rim bah! So I tried a solution...used some of that rust dissolver from wd40. I made a little dam with clay on a small area to see how well it would work. It's supposed to be safe on paint. Looks like it worked pretty well! Juts gotta do the rest...

http://primaryboost.com/store/rt/springupgrade13/DSC_1737.JPG

http://primaryboost.com/store/rt/springupgrade13/DSC_1738.JPG

green-lantern
04-10-2013, 08:27 PM
Toni, the brake dust, that's called riding it hard and putting it up wet. lol

Some reason your threads always make me want to work on my car. Probably because when I got to know you a little you were having a bunch of trouble out of it. Now it's one of my favorite cars (even though it's a stealth).

Toni
04-10-2013, 08:51 PM
Haven't heard that phrase in a long time lol!

green-lantern
04-10-2013, 10:38 PM
Haven't heard that phrase in a long time lol!

I'm old and you still owe me a six pack of home brew. :D

Toni
04-11-2013, 11:53 AM
Lol I know!

Toni
04-14-2013, 10:29 PM
Rear gasket and cam caps installed. 1/2/5 syncros replaced.

http://primaryboost.com/store/rt/springupgrade13/DSC_1746.JPG

http://primaryboost.com/store/rt/springupgrade13/DSC_1747.JPG

Old synchro bottoming out...
http://primaryboost.com/store/rt/springupgrade13/DSC_1748.JPG

New one.
http://primaryboost.com/store/rt/springupgrade13/DSC_1749.JPG

Toni
04-18-2013, 12:50 AM
Bunch of progress!

300m output shaft
http://primaryboost.com/store/rt/drivetrain0313/DSC_1702.JPG

Humpty dumpty!
http://primaryboost.com/store/rt/springupgrade13/DSC_1757.JPG

New clutch and had the pads replaced on the fly.
http://primaryboost.com/store/rt/springupgrade13/DSC_1754.JPG

Installed
http://primaryboost.com/store/rt/springupgrade13/DSC_1758.JPG

Oil temp sensor
http://primaryboost.com/store/rt/springupgrade13/DSC_1763.JPG

Brake cooling deflectors
http://primaryboost.com/store/rt/springupgrade13/DSC_1772.JPG

Methanol filter and failsafe flow meter
http://primaryboost.com/store/rt/springupgrade13/DSC_1775.JPG

Top side done!
http://primaryboost.com/store/rt/springupgrade13/DSC_1781.JPG

Primus101
04-18-2013, 05:36 AM
Not sure why they were leaking, used new caps during the rebuild.


Probably leaking out from under the cam journal caps themselves-I just had the same issue with my new 10k mile ones, & found oil between the cam cap & head surface. I think its a good idea to apply a small amount of sealer between, in the area of the end plug. I was convinced the plugs were leaking as well, but the oil was just wicking around them. You may have to revisit that area-

Toni
04-18-2013, 08:59 AM
I may not :) I thought the same thing this time around and did put a film of sealant there.

Toni
04-23-2013, 02:07 PM
Alright well got the car back together last Friday and put 300 miles on it so far (mostly highway). So I made my deadline but still have some bugs to work out. Major one is the clutch but I'll start a new thread cause it'll just get lost in here.

Toni
04-27-2013, 08:48 PM
Well I am back on track after getting the clutch sorted out. I still have to do the rear shocks, new rotors, mount and wire up the aem meth failsafe, and install my app radio2.

Toni
04-28-2013, 11:41 PM
So shiny!

http://primaryboost.com/store/rt/springupgrade13/DSC_1783.JPG

AEM meth failsafe gauge installed. Color matches the rest of the gauges but the pic shows it a bit off. (except afr).

http://primaryboost.com/store/rt/methinjection/DSC_1972.JPG

http://primaryboost.com/store/rt/methinjection/DSC_1965.JPG

Blackmount
04-29-2013, 03:59 AM
looks great!! will we get a video?

AdamVR4
04-29-2013, 03:41 PM
What kind of clutch is that? Looks different.

What oil temp sensor / gauge did you use?

Love the brake cooling deflectors. Pick those up from GZP or what?

Toni
04-29-2013, 03:52 PM
looks great!! will we get a video?

Of course! Just gonna work out the bugs and break in the clutch first.


What kind of clutch is that? Looks different.

What oil temp sensor / gauge did you use?

Love the brake cooling deflectors. Pick those up from GZP or what?

Clutch is a southbend stage 3 endurance.

Oil temp gauge/sensor is the apexi el2s, same as my other gauges.

Yup, I believe they have them in stock. I have done nothing to tune my brake temperatures so they may actually be hurting me lol. I may keep them off for street use.

Toni
05-08-2013, 10:03 PM
Some more pics!

New rear shocks
http://primaryboost.com/store/rt/springupgrade13/DSC_1976.JPG

Old tcase spool
http://primaryboost.com/store/rt/springupgrade13/DSC_1981.JPG

New Spool
http://primaryboost.com/store/rt/springupgrade13/DSC_1982.JPG

Nice and clean under there!
http://primaryboost.com/store/rt/springupgrade13/DSC_1986.JPG

Clean rotors dirty wheels!
http://primaryboost.com/store/rt/springupgrade13/DSC_1988.JPG

Blackmount
05-09-2013, 08:38 PM
[QUOTE=Toni;236211]Some more pics

Nice and clean under there!
http://primaryboost.com/store/rt/springupgrade13/DSC_1986.JPG

are the LC1's waterproof? I'd be worried about it getting wet!

R/T93
05-09-2013, 08:39 PM
Of course they are water proof

Blackmount
05-09-2013, 08:42 PM
well this would have been nice to know about 15-20 installs ago...

Toni
05-09-2013, 10:45 PM
Lol, yup very waterproof. The wires are sealed and the o2 connector has a rubber gasket. I don't think the manual specifically says it can get wet but it does say to run wires from the LC1 into the interior so that seams to mean that the unit stays on the exterior. The o2 sensors wires are generally short so they usually can't reach anyway.

Blackmount
05-10-2013, 07:41 AM
I usually tuck them away somewhere on the fender towards the hood, tho I can think of a few situations it would have been much easier to just mount it under the engine on something like a subframe.

2fnloud
05-10-2013, 08:11 AM
Been gathering parts for the better part of a year. If things go to plan in two weeks the following will be done:

Engine Related
3SX Poly motor mounts
IPS Baffled Oil Pan
GZP Pre-Set Cam Gears
3rd Gen Lifters
EGR / VAC. Reduction
Krank Vents
Greddy Type S B/O Valve
Pre-Turbo Hard Pipes
3SX Phenolic Spacers

Exhaust Related
Stillen D/P
3SX Rear pre-cat delete

Suspension Related
New ECS Struts
Tein pillow strut mounts (front & rear)
Custom Tuned Ground Control Sleeve Kit (Thrust bearings, compound springs...progressive tender & main spring)
Saner Sway Bars

Brake Related
JDM front brake ducts

DrGonzo
05-10-2013, 09:15 AM
Old tcase spool
http://primaryboost.com/store/rt/springupgrade13/DSC_1981.JPG

New Spool
http://primaryboost.com/store/rt/springupgrade13/DSC_1982.JPG



Toni, With your spool being that worn did you have any clunking issues. Like when you let off the gas you got a clunk or jerking giving it gas?

I'll be dropping my t-case this weekend to see if it is indeed my t-case spool/output shaft that could be causing the clunking issues I'm having. After checking the rear dif backlash and filling in the carrier bearing solid I'm running out of options....

Primus101
05-10-2013, 02:56 PM
Hey Gonzo..could very likely be extra lash on the three pins between the planetary gear set & VCU

Toni
05-10-2013, 04:33 PM
Toni, With your spool being that worn did you have any clunking issues. Like when you let off the gas you got a clunk or jerking giving it gas?

I'll be dropping my t-case this weekend to see if it is indeed my t-case spool/output shaft that could be causing the clunking issues I'm having. After checking the rear dif backlash and filling in the carrier bearing solid I'm running out of options....

I've been chasing clunk for years myself. In fact, I think it's the clunk that is causing the splines to wear faster. I've done the same, and even went as far as adjusting the backlash in the rear end to the low end of spec. I've gotten new carriers, bushings, etc. I even ran with a one piece cfds. My guess is I have a bunch of small wear throughout the system that just adds up.

Long story short. I wasn't exactly checking for clunk before and after this change. I just didn't want to wear out my new 300m shaft and waste money down the road. We'll see after I get the clutch crap worked out and I can actually drive the car.


Hey Gonzo..could very likely be extra lash on the three pins between the planetary gear set & VCU

Yup, this is a good one to check. I had this issue myself and that helped some.

DrGonzo
05-10-2013, 05:07 PM
Hey Gonzo..could very likely be extra lash on the three pins between the planetary gear set & VCU

Are you referring to the pins you have to knock out where removing the output shaft correct? I remember having to knock some pins out when I pulled my output shaft last year to check it. I'm not a transmission person and this is driving me nuts.


I've been chasing clunk for years myself. In fact, I think it's the clunk that is causing the splines to wear faster. I've done the same, and even went as far as adjusting the backlash in the rear end to the low end of spec. I've gotten new carriers, bushings, etc. I even ran with a one piece cfds. My guess is I have a bunch of small wear throughout the system that just adds up.

Long story short. I wasn't exactly checking for clunk before and after this change. I just didn't want to wear out my new 300m shaft and waste money down the road. We'll see after I get the clutch crap worked out and I can actually drive the car.


I can surely tell mine is coming from the front and seeing how bad you input spool was makes me even more confident that it is the issue. If the weather holds out I'm going to try and check the input spool this weekend. LMK if it fixes your issues.

R/T93
05-10-2013, 05:12 PM
My spool and OS are brand new looking and I have a clunk. I think its the TC gear or the diff ring gear in the front.

From the phone.

Blackmount
05-10-2013, 05:14 PM
I too have a clunk on occasion when shifting gears or on/off throttle. I never notice it during WOT tho.

Toni
05-10-2013, 05:21 PM
Are you referring to the pins you have to knock out where removing the output shaft correct? I remember having to knock some pins out when I pulled my output shaft last year to check it. I'm not a transmission person and this is driving me nuts.


These pins (http://primaryboost.com/store/rt/centerdiffassem/)

DrGonzo
05-10-2013, 05:30 PM
These pins (http://primaryboost.com/store/rt/centerdiffassem/)

Gotcha. Yeah I have never messed with those pins or broken down that trans that far. One of these days I'm going to head over to Chris's shop so we can look into it.

Toni
09-12-2013, 10:58 AM
Well, I am finally done with my clutch issues. I will be hitting the track next weekend. Hoping for some 11s!

Toni
04-02-2014, 04:47 PM
Well, my best last year was an 11.673@121.56 with a 1.783 60ft. Turns out, my vcu was shot so I ended up spinning the fronts without even realizing.

New for 2014

rebuilt vcu
billet dr650s
poly control arm bushings

Should be fun!!!

CoopKill
04-02-2014, 05:20 PM
And vids this time!

Toni
04-02-2014, 05:27 PM
I haz vids


https://www.youtube.com/watch?v=8gY8jY4He1c

CoopKill
04-02-2014, 05:51 PM
What are you using for the data display?

Toni
04-02-2014, 06:06 PM
It's innovate logworks playback overlayed on the video.

HLxDrummer
04-02-2014, 06:43 PM
Cool video! Looks like your gearing is perfect for your power level judging by your RPMs in third lol

Toni
04-03-2014, 09:59 AM
Yeah not sure what I'd do with more power/trap speed. I'm certainly going to start hitting the edge soon.

AdamVR4
04-03-2014, 11:38 AM
Yeah not sure what I'd do with more power/trap speed. I'm certainly going to start hitting the edge soon.

Shift to 4th. There's no power that late in 3rd and the engine is highly stressed.

You know the slip is going to be good when you had to go into 4th (unless you did it to quench knock late in 3rd)

Toni
04-03-2014, 11:44 AM
At the moment I'm staying in 3rd a little later because by the time I got into 4th I would be past the line.

Toni
04-13-2014, 12:05 AM
Turbos ready to drop in!

http://primaryboost.com/store/rt/dr650/DSC_6364.JPG

Toni
04-21-2014, 04:54 PM
Yup....

Don't strip the control arm bracket bolt then cross thread the helicoil tap. Luckly, the next sized sae bolt still works. I plan to do the front subframe bushings at some point so I may get a new subframe because I hate mismatched bolts.

http://primaryboost.com/store/rt/polycontrolarmbushings/DSC_6370.JPG

Jimvr4
04-21-2014, 05:14 PM
Turbos ready to drop in!

http://primaryboost.com/store/rt/dr650/DSC_6364.JPG

Do I see the special turbo oiling system block off plugs that Coopkill used in his build?

Toni
04-21-2014, 05:15 PM
:lol: yup!

green-lantern
04-21-2014, 05:53 PM
Do I see the special turbo oiling system block off plugs that Coopkill used in his build?

:lo5l:


Are these the DR650's Toni?

Toni
04-21-2014, 08:59 PM
:lo5l:


Are these the DR650's Toni?

Yeah. Nothing too crazy. I'm hoping to gain 25hp or so over the 15gs and maybe a little area under the curve overall. Make it a bit easier to get into mid 11s or maybe better?

Toni
04-22-2014, 03:43 PM
This is why I couldn't get a better launcher last couple years. Should be all good now :)

https://dl.dropboxusercontent.com/u/29716828/rt/badvcu.jpg

green-lantern
04-22-2014, 08:57 PM
Probably feel like a new car.

Toni
04-22-2014, 11:04 PM
We shall see! Just got the car put back together tonight but it was raining so I gotta wait another day. Dyno this weekend unless some other bugs pop up.

Toni
04-26-2015, 09:47 PM
Tackled a few problems Friday/Saturday at GZP.

Replaced clogged to shit condensor
Koyo 2" radiator
Poly subframe bushings
AWS delete
Poly sway bar bushings
And fixed a couple mystery clunks by the turn of Hans' wrench lol.

http://www.primaryboost.com/store/rt/rearsubframe/IMAG0989.jpg

http://www.primaryboost.com/store/rt/rearsubframe/DSC_7544.JPG

http://www.primaryboost.com/store/rt/rearsubframe/DSC_7545.JPG

http://www.primaryboost.com/store/rt/rearsubframe/DSC_7546.JPG

http://www.primaryboost.com/store/rt/rearsubframe/IMAG1002.jpg

http://www.primaryboost.com/store/rt/rearsubframe/IMAG0996.jpg

http://www.primaryboost.com/store/rt/rearsubframe/IMAG1000.jpg

http://www.primaryboost.com/store/rt/rearsubframe/DSC_7547.JPG

http://www.primaryboost.com/store/rt/rearsubframe/DSC_7548.JPG

http://www.primaryboost.com/store/rt/rearsubframe/DSC_7549.JPG

http://www.primaryboost.com/store/rt/rearsubframe/DSC_7550.JPG

http://www.primaryboost.com/store/rt/rearsubframe/DSC_7551.JPG

http://www.primaryboost.com/store/rt/rearsubframe/DSC_7555.JPG

DrGonzo
04-27-2015, 12:15 AM
your getting a fair share of rust under there.... might want to think about soda blasting those rust spots and treating them before they get out of hand.

BTW, build it looking awesome!!! Look forward to seeing it at NG if your going to make it.

Toni
04-27-2015, 10:18 AM
Yeah there is a bit of rust. I think the camera makes it look worse than it is. I decided not to get the subframe powdercoated because it looked fair when I was under the car. In hindsight I probably should have picked up some rust converter ahead of time and just sprayed it with that. Luckily the under body was almost completely rust free which is where I thought I'd see a ton.

Toni
05-11-2015, 03:36 PM
I'm just going to turn this thread into my build lol.

Had to do some massaging to get the koyo to fit perfectly and not hit the AC bolt or hood. Just had to trim the fan frame and upper radiator hardpipe. Picked up Maximal's brackets and coolant reserve tank from GZP. Everything fits with no stress now! Rest of the bay is a little dirty so pretend I thought enough ahead to clean it for a pic lol.

http://www.primaryboost.com/store/rt/koyoradoverflowtank/DSC_7589.JPG

http://www.primaryboost.com/store/rt/koyoradoverflowtank/DSC_7590.JPG

NOMIEZVR4
05-11-2015, 04:36 PM
Looking good man! I don't know how you guys don't get claustrophobic with the tight engine bays...:p

green-lantern
05-11-2015, 07:41 PM
The car has come a long way Toni! Looks great, lots of great upgrades.

Toni
09-17-2015, 09:51 AM
Side splitters added!

http://primaryboost.com/store/rt/sidesplitters/DSC_9219.JPG

http://primaryboost.com/store/rt/sidesplitters/DSC_9211.JPG

http://primaryboost.com/store/rt/sidesplitters/DSC_9223.JPG

http://primaryboost.com/store/rt/sidesplitters/DSC_9204.JPG

http://primaryboost.com/store/rt/sidesplitters/DSC_9208.JPG

Chris@Rvengeperformance
09-17-2015, 10:35 AM
looks good

NOMIEZVR4
09-17-2015, 11:23 AM
how far past the tires do those skirt extensions stick out? It seem that they stick out a bit too much..

Beef6
09-17-2015, 11:54 AM
Gorgeous!

Toni
09-17-2015, 12:15 PM
how far past the tires do those skirt extensions stick out? It seem that they stick out a bit too much..

They don't stick out past the tires at all.

http://primaryboost.com/store/rt/sidesplitters/DSC_9221.JPG

NOMIEZVR4
09-17-2015, 12:47 PM
I guess the 3000GT versions do...you'res seems more subtle

Toni
09-17-2015, 01:13 PM
Yeah, I think the 1gen stealth sides dont stick out far to begin with, you dont need to extend the splitters even further. Also they already have a recess where it sits.