PDA

View Full Version : Need some quick front wheel bearing clarification



x2xtreme360
09-28-2010, 01:57 PM
I just need to make sure that I'm getting what I need here. The front passenger wheel has very noticeable play in it in every direction and I'm sure it's the wheel bearing. I need to clarify that on the AWD drivetrain, the entire hub assembly needs to be replaced to replace the bearing, correct? It's an integrated unit from what I can tell.

I'm looking at part number MR223993 and I'm having the local dealership order this so it's in by Thursday. I need to make sure this is what I need as the car needs to be working by Saturday.

Lithium
09-28-2010, 02:01 PM
I'm guessing you mean the hub as in studs and bearing and not the entire cast knuckle assembly? Because yes its easier to just replace the assembly as in bearing and hub with studs.

http://www.3sx.com/store/comersus_viewItemBundle.asp?idProduct=631

x2xtreme360
09-28-2010, 02:05 PM
Correct. Don't need the knuckle. I only need a new wheel bearing, but the bearings appear to seat inside the hub as an integral unit.

http://img.photobucket.com/albums/v226/HwFRemington/DSCF3879.jpg
This one is obviously broken, but you get the idea.

So, I suppose I will have them get this for me then.

neveret
09-28-2010, 02:06 PM
yes, generally speaking you get the hub assembly that bolts in to the steering knuckle when replacing the wheel bearing. If this is the first time you have had to remove the halfshaft, you'll be in for a battle. the splines of the shaft are usually rusted and fused to the splines of the hub and make it nearly impossible to separate (unless you have a torch and a press). Good luck.

Lithium
09-28-2010, 02:07 PM
I was looking into just replacing the bearing too but couldnt find one that would work. I ended up buying them from 3sx and I couldnt be happier, Made a world of difference.

Austin@STM
09-28-2010, 02:08 PM
Yea its a complete assembly that you bolt it. They are $100 for an OEM replacement.

Lithium
09-28-2010, 02:09 PM
yes, generally speaking you get the hub assembly that bolts in to the steering knuckle when replacing the wheel bearing. If this is the first time you have had to remove the halfshaft, you'll be in for a battle. the splines of the shaft are usually rusted and fused to the splines of the hub and make it nearly impossible to separate (unless you have a torch and a press). Good luck.




It can be a pain but make sure you dont damage the threads in the process. Upon re-installation a small amount of anti-seize will do wonders.

x2xtreme360
09-28-2010, 02:10 PM
yes, generally speaking you get the hub assembly that bolts in to the steering knuckle when replacing the wheel bearing. If this is the first time you have had to remove the halfshaft, you'll be in for a battle. the splines of the shaft are usually rusted and fused to the splines of the hub and make it nearly impossible to separate (unless you have a torch and a press). Good luck.

I own a hub removing slide hammer, so I'm not too worried about it:p

neveret
09-28-2010, 02:16 PM
if that oem part number is right, it's cheaper to buy factory than it is to buy from the parts store. 84$ from mentor mitsu, and 198$ from Advance Auto.

x2xtreme360
09-28-2010, 02:22 PM
I'm forced to buy from my local dealer due to the fact that I need this part in like 2 days. I just paid them for it... $120

Not a bad price considering the urgency of the situation.

And yes, I try to go OEM for practically everything.

HLxDrummer
09-28-2010, 02:37 PM
Just replaced both when I did my brakes. What a PITA to get them off, though! Worth it in the end, however.