View Full Version : Question on battery relocation and accuracy of gauges.
terrets
09-26-2010, 03:28 AM
Ive got a 91 vr4 mostly stock as of now. I relocated my battery to the trunk using 00 cable. My voltmeter reads about 11.3 or 11.7 idling and I think 12.2 with throttle(cant remember, havent been driving the car). Im curious if this will throw the accuracy off of my stri gauges and how much? Also is it bad for the injectors/ecu/EMU(not in yet) or anything else? Is there anything I can do such as a farad capacitor in the engine bay(dont know if it can be near heat) or under the dash. Also would running another cable help with the voltage drop? Maybe a better alternator? Better ground?
Thanks for the help guys. Loving the new website although I still go to 3si for all the archieved threads. Please dont hate, it still has loads of info. :).
BaadVR4
09-26-2010, 09:18 AM
Ive got a 91 vr4 mostly stock as of now. I relocated my battery to the trunk using 00 cable. My voltmeter reads about 11.3 or 11.7 idling and I think 12.2 with throttle(cant remember, havent been driving the car). Im curious if this will throw the accuracy off of my stri gauges and how much? Also is it bad for the injectors/ecu/EMU(not in yet) or anything else? Is there anything I can do such as a farad capacitor in the engine bay(dont know if it can be near heat) or under the dash. Also would running another cable help with the voltage drop? Maybe a better alternator? Better ground?
Thanks for the help guys. Loving the new website although I still go to 3si for all the archieved threads. Please dont hate, it still has loads of info. :).
I would have the alternator checked. Sounds like it may be broke. Also, did you replace the charging wire with -4 wire? If not, that's a good idea also.
terrets
09-26-2010, 11:04 PM
I did not. Do you mean 4 gauge by -4?? I will have the alternator checked. Thanks.
BaadVR4
09-27-2010, 10:20 AM
I did not. Do you mean 4 gauge by -4?? I will have the alternator checked. Thanks.
Yes, 4 gauge wire for the wire that runs from the alternator to the fuse box and from the fuse box to the starter lug (which is where the wire actually "connects" to the positive side of the battery).
The issue is primarily voltage drop in the length of cable, especially the cable from the battery positive terminal. A related issue is current carrying capacity of the wiring. The additional voltage drop associated with long cable runs causes higher current which requires larger gauge wire to handle the additional heat generated.
Austin@STM
09-27-2010, 12:27 PM
If you turn the car on, then turn on the high beams, defrost on rear window, crank the heat, turn on the radio, what is the voltage. Sounds like you alternator is toast or on its way out. Check all your connections first, might be a poor ground or bad connection somewhere also.
Atrosity
09-28-2010, 05:27 PM
Definitely check your ground connections, that was my problem and it caused a lot of issues.
Patryn
09-28-2010, 06:19 PM
I would recommend cleaning the ground points as mentioned above. I ran into the same issue, then just sanded down all the ground points wether they looked clean or not, and that solved my voltage issue. Places with paint are obvious, but other areas looked normal, but guess sanding them to a polish did the trick for me.
I got a Gas Torch and soldered my earths to the rail..problem effing solved :p
then painted over the solder job.
terrets
09-29-2010, 03:59 AM
I got a Gas Torch and soldered my earths to the rail..problem effing solved :p
then painted over the solder job.
Not a bad idea.
I scraped off all the paint where I grounded the battery but I will check any other grounds.
And Austin, Ill check the voltage tomorrow.
Thanks for the ideas guys.
terrets
09-29-2010, 01:01 PM
If you turn the car on, then turn on the high beams, defrost on rear window, crank the heat, turn on the radio, what is the voltage. Sounds like you alternator is toast or on its way out. Check all your connections first, might be a poor ground or bad connection somewhere also.
Hey Austin, I did this after my car has been sitting for a while. Voltage is 10 with the car off and with the car on its about 12.2~12.4 but Im not sure if this is because she was idling at ~2k and not the normal idle. I think Im going to fix my clutch hose and drive it again for a month because I just miss it so much. I could have sworn it was under 12 though.....
Are these alternators rebuildable??
Thanks.
from what I'm aware all alternators are rebuildable :)
terrets
09-30-2010, 01:37 AM
I thought so :). Just like starters. My question is, is it only the copper brushes? Or bearings for the pulley also?
Uhhm, usually the diodes/rectifiers.
ver fer
10-31-2010, 07:07 PM
Where are you grounding the battery and what size wire are you using?
Patryn
10-31-2010, 07:12 PM
I would use a two gauge or larger wire. I located my battery right behind the rear seats. Built a small holder for it out of some aluminum bars I bought at Home Depot. Then just found a locating on the frame right next to the battery in the trunk area and grounded it to the frame. Just make sure that you clean all your ground points off, whether its paint or just dirty. A wire brush on the dremel or some sand paper will do the trick.
terrets
10-31-2010, 07:38 PM
I would use a two gauge or larger wire. I located my battery right behind the rear seats. Built a small holder for it out of some aluminum bars I bought at Home Depot. Then just found a locating on the frame right next to the battery in the trunk area and grounded it to the frame. Just make sure that you clean all your ground points off, whether its paint or just dirty. A wire brush on the dremel or some sand paper will do the trick.
Did this. With 00. It has a good voltage when idling now. Not sure why it changed..
you guys massively overdo it! 00 wire? holy crap! that must be massive!
ver fer
10-31-2010, 10:55 PM
What voltage are you seeing at the battery now?
terrets
11-01-2010, 02:29 AM
It is massive. And hidden except in the bay :D.
Upwords of 12.7, 12.8. I did see 13 on there? Is that alright? :lol: I know our pickup truck hits 14.
ver fer
11-01-2010, 03:00 AM
It's a little low, it should be closer to 14V. As far as affecting the accuracy of the gauges. No, most will supply some sort of 5v based voltage to the sensor.
MightyMouse
11-01-2010, 12:00 PM
00 Gauge is the way to go. It allows for more length and more accessories hanging off of it. Of course, you probably only need 2 connections under the hood (1 for the starter and one of the the fuse box).
I recommend using at least a 2 for power and a 0 for ground.
Upgrade the fuse box to a 4ga at a minimum in my opinion as well.
Here's a good write-up, by the way..
http://www.stealth316.com/2-battery-move.htm
I'm using a Kinetik KHC-800. It gets the job done in Memphis, but not sure how well it would do in a colder climate. Always always make sure your ground wire is making very good contact and save some money. Don't run the ground to the engine bay, just run multiple smaller grounds to the frame, body, and other areas of the car.
The seat belt bolt holes are a good spot, as are the strut mount areas, and the spare tire bolt.
All of these can keep your wires well hidden as well.
ver fer
11-01-2010, 12:28 PM
^^^ Correct. Your ground wire should be close to the same size as you power wire, preferably the same size or bigger and as close to the battery as possible. The ground should be connected to some part of the frame. Don't just screw it to the floor.
terrets
11-02-2010, 06:10 AM
Guys. My ground is the same size and it is 2 feet from the battery to the frame behind the rear seats >_<. I routed it the same way without seeing he did it that way :D. I read most of that write up before I did this. I am using a 250 or 200 amp fuse, cant remember.
I could probably get a better battery but it still has warranty on it and was nearly brand new.
I do have a 00/0 to 3 2/4 port Rockford Distribution Block :D
Thanks for the idea for the fuse box.
MightyMouse
11-02-2010, 09:16 AM
Move the Fuse box while you're at it.. ;)
Mine is behind my front fender, I have access to it through the sidemount hole on the 99 bumper, I've driven in very hard rain and 8+ inches of water (slowly) without any problems.
It cleans the engine bay quite a bit..
Atrosity
11-02-2010, 12:00 PM
Move the Fuse box while you're at it.. ;)
Mine is behind my front fender, I have access to it through the sidemount hole on the 99 bumper, I've driven in very hard rain and 8+ inches of water (slowly) without any problems.
It cleans the engine bay quite a bit..
Pics of the engine? :D
ver fer
11-02-2010, 01:06 PM
I just wanted to make sure the wiring was good before blaming the alternator. It's not hard to pull the alternator, but why pull it if you don't have to. Drive the car around for a while if you not storing it to see if the battery actually is charging. If it is I wouldn't worry about it.
MightyMouse
11-02-2010, 06:00 PM
Yeah, the wiring is to the fuse box could be an issue on it's own. I recommend replacing that regardless of all other things and double check your ALT fuseable link.
Mine was a mess..
I have some pictures in my blog post if you want to see the engine bay with the fuse box relocated.
terrets
11-03-2010, 04:33 AM
Ya Im going to move my box :) And get rid of cruise and A/C :D. Thanks guys.
MightyMouse
11-03-2010, 08:33 AM
And then you're buying some fuel rails!
terrets
11-04-2010, 01:18 AM
:lol: I dont know about that...I need 8an in mine ;)
Powered by vBulletin® Version 4.2.3 Copyright © 2026 vBulletin Solutions, Inc. All rights reserved.