PDA

View Full Version : Cleanest Way to Run Fuel Pump Hotwire



HLxDrummer
09-25-2010, 09:32 PM
How does the stock wiring run? From the tank through some grommet into the car and then under the hood? I wouldn't think it would run the length of the underside.

I don't really like having my wiring coming out of that access panel in the trunk and would like to run it with the stock wiring if it's not too much of a PITA..

x2xtreme360
09-26-2010, 12:45 AM
Mine is run very clean. I ran it through the grommet behind the battery and it runs all the way with the stock wiring under the door sills. I even went as far as tucking it with the wiring under the plastic covering. It the goes behind the rear quarter trim, into the trunk, and then the relay is mounted under the access panel to one of the studs that holds the pump to the tank. You wouldn't ever think it was aftermarket.

Show Killer
09-26-2010, 01:42 AM
My battery is in the rear so mine is really clean.

Atrosity
09-26-2010, 02:35 AM
I ran mine through passenger side grommet and ran it under the carpet. It is very clean because you can't see it. :)

DocWalt
09-26-2010, 04:14 AM
Mine is like Atrosity's, but on the other side of the car. Thank you previous owner for the abandoned high grade power wire!

enigma
09-26-2010, 09:59 AM
The whole idea of upgrading to the thicker wire is to increase ampage under load so you benefit from the direct current from the battery.

RL7
09-27-2010, 03:04 AM
The stock wiring runs pretty much full circle around the car. You probably don't want to follow that. The fuel pump circuit is part of the trunk/tail light harness. You will probably have to remove all the plastic panels from the trunk to gain proper access. There should be a connector in the very rear corner, behind the L-shaped access panel where the ecs computer connects. That goes to the fuel harness and probably through a grommet to the outside (I say probably because I have never actually looked for this grommet). You could probably go through that to the outside with the power wire from the battery or even place the relay at this location rather than outside the car.

HLxDrummer
09-28-2010, 02:33 PM
RL7 could you explain a little more? I'm slightly confused without actually looking at it.

I will either run it completely with the stock wiring so I don't have to have it sticking out of the access panel or run it behind the battery/door sill/trim/etc.

MADMarc
09-28-2010, 02:47 PM
Sounds like I ran mine similar to Atrosity's. I mounted the relay on a corner mount of the ECS computer but the only wires you can see are when you pull the storage tray in the hatch that goes to the fuel pump door :) I like it because I can't tell its there hahah

Atrosity
09-28-2010, 03:42 PM
Sounds like I ran mine similar to Atrosity's. I mounted the relay on a corner mount of the ECS computer but the only wires you can see are when you pull the storage tray in the hatch that goes to the fuel pump door :) I like it because I can't tell its there hahah


ahaha Yup! I ran my sub wire and that wire at the same time so its clean, its on the side under the carpet so you just don't see it at all.

RL7
09-28-2010, 04:13 PM
RL7 could you explain a little more? I'm slightly confused without actually looking at it.

I will either run it completely with the stock wiring so I don't have to have it sticking out of the access panel or run it behind the battery/door sill/trim/etc.

I'm more or less going by this diagram. I don't really like the wire passing into the access panel either. I didn't actually dig back there to do it this way, but it seems like it could be a better way.
1061

HLxDrummer
09-28-2010, 06:45 PM
I see what you saying now. Looks kinda like it goes behind the trim then through a grommet to the tank, huh? I like this idea but not sure how much of a PITA it would be to install this way outside my apartment with no jack/stands.. Also kind of worry about having a relay right on top of the fuel tank, unless I put it inside the car behind the panels but then that's more soldering..

Decisions decisions..

Austin@STM
09-28-2010, 06:53 PM
It works out nicely running it down from the battery and following the PS lines that run under the car, you can get it up inside the plastic cage, and then up on top of the tank so it doesnt go through anything. That would be a nice clean way of doing it, without taking half the car apart.

Otherwise like has been mentioned, run it with all the other harnesses, so that it just looks like its part of it. Thats why we include some wire loom in our kit so any where ethe wire is visible, you can cover it with black loom and it looks just like the factory wire harness, instead of a big red wire hanging out on its own.

HLxDrummer
09-28-2010, 08:39 PM
Thanks for the input Austin. I'm not too keen on running power wires under the car that far and I'm sure all the bolts holding up that plastic will break but I'll keep it in mind haha.

Does anyone know how the stock wiring goes? The diagram makes it seem like there is a grommet behind one of the plastic panels and the wiring runs on the interior until it gets to grommet then goes on top of the tank..

Austin@STM
09-28-2010, 09:02 PM
There is a grommet right behind the tank that you can run the power wire through, then run it under the dash, under the carper and all down that side, then through the access panel for the fuel pump would be the other shortest route.

HLxDrummer
09-28-2010, 09:57 PM
Alright thanks man I appreciate it! Hopefully I can get this done soon so I can get it a little tuning :)

wraith
09-28-2010, 11:48 PM
I had my car at Rays and they did something pretty slick. They ran the fp wire from the ignition harness back to the pump so no need for relays or anything. I thought that was pretty smart since the ignition probably draws more then the pump would so it shouldnt ever overheat.

91STT
09-29-2010, 12:51 AM
The way I routed mine is not the easiest but it is very clean looking.
I ran the 10 gauge wire from the engine compartment into the fender via the ABS grommet.
From there I entered the passenger compartment through the door jamb grommet.
Than down the passenger kick panel, along the passenger rocker panel under the carpet, under the seat, behind the quarter panel trim panel to the area by the ECS control unit.
I drilled a hole near where the existing fuel pump wiring is and installed a grommet.
I zip tied the new wire to the existing fuel pump wire all the way to the pump.
Unless you knew what I did, you would probably not be able to tell anything was done.
Lots of disassembly but well worth it to me.

HLxDrummer
09-29-2010, 10:28 AM
I had my car at Rays and they did something pretty slick. They ran the fp wire from the ignition harness back to the pump so no need for relays or anything. I thought that was pretty smart since the ignition probably draws more then the pump would so it shouldnt ever overheat.

That is a nice idea but I don't really like messing with the factory wiring if I don't have to. Especially the ignition/starter stuff when I already have a turbo timer/security system on it.


The way I routed mine is not the easiest but it is very clean looking.
I ran the 10 gauge wire from the engine compartment into the fender via the ABS grommet.
From there I entered the passenger compartment through the door jamb grommet.
Than down the passenger kick panel, along the passenger rocker panel under the carpet, under the seat, behind the quarter panel trim panel to the area by the ECS control unit.
I drilled a hole near where the existing fuel pump wiring is and installed a grommet.
I zip tied the new wire to the existing fuel pump wire all the way to the pump.
Unless you knew what I did, you would probably not be able to tell anything was done.
Lots of disassembly but well worth it to me.

Interesting :) I'll have to take a look at that. Any reason you didn't run the new wire along with the factory wiring instead of making a new hole? Is it hard to zip tie the new line to the originals without having the car in the air?

Thanks!

91STT
09-29-2010, 11:09 AM
That is a nice idea but I don't really like messing with the factory wiring if I don't have to. Especially the ignition/starter stuff when I already have a turbo timer/security system on it.



Interesting :) I'll have to take a look at that. Any reason you didn't run the new wire along with the factory wiring instead of making a new hole? Is it hard to zip tie the new line to the originals without having the car in the air?

Thanks!

The existing grommet is too small for fit the factory wire and the new 10 ga.
I did not want to remove the OEM wire so I just drilled a hole next to the existing one.
The factory harness that goes from the quarter panel area to the top of the fuel tank is very accessible with the car on jack stands.
If you look under the right side of the rear bumper, the harness that comes down through the body and over the fuel tank is the harness for the FP.

reallyxxxxxxloud
09-29-2010, 11:37 AM
I had my car at Rays and they did something pretty slick. They ran the fp wire from the ignition harness back to the pump so no need for relays or anything. I thought that was pretty smart since the ignition probably draws more then the pump would so it shouldnt ever overheat.

Nice Idea thanks !!!! I'll definitely be doing that.

Chris@Rvengeperformance
09-29-2010, 06:20 PM
yeah but does the pump stop if the engine stalls? Stock and with typical hot wires it does and if you are in a wreck it can save your life. Yeah the NAs don't either, but I like that feature. My ford has a rollover pump kill as well.