PDA

View Full Version : Cleaning up anodized nickel



GRSHOPR
10-19-2012, 03:25 AM
Ok, so all of the various screws and small bolts all over the bodies of our cars, are starting to corrode. Anyone got suggestions on how to restore them, or clean them up to looking fresh again? Thanks.

Chris@Rvengeperformance
10-19-2012, 10:53 AM
If they are corroded already then they have to be re-plated to look like new again. Eastwood makes a spray that tries to re-create the plated appearance, but reviews are mixed.

Sent from my DROIDX using Tapatalk 2

Ange
10-19-2012, 11:19 AM
replace them with ss or alu?

Chris@Rvengeperformance
10-19-2012, 01:28 PM
stainless bolts are grade 2, too weak for anything but trim pieces. aluminum bolts are even weaker.

http://reviews.ebay.com/Stainless-Bolts-Usually-very-weak?ugid=10000000001623345

GRSHOPR
10-19-2012, 02:09 PM
Maybe just easier to paint them? I'm assuming replating them is difficult?

Ange
10-19-2012, 04:26 PM
stainless bolts are grade 2, too weak for anything but trim pieces. aluminum bolts are even weaker.

eBay Guides - Stainless Bolts--Usually very weak (http://reviews.ebay.com/Stainless-Bolts-Usually-very-weak?ugid=10000000001623345)

really didn't know ss was weaker. was planning on replacing all mine with ss eventually lol.

titanium then :p

MeTarzan
10-19-2012, 06:19 PM
stainless bolts are grade 2, too weak for anything but trim pieces. aluminum bolts are even weaker.

Well we deal with lots of SS bolts and most are Grade 5 which is PSI rating of 125,000 PSI. A grade 8 bolt has a stronger rating with a PSI of 150,000.
so unless its attaching your drive shaft or a suspension component a SS bolt would a good choice as long as you remember to put a little dab of anti-seize on the threads.

Chris@Rvengeperformance
10-19-2012, 09:11 PM
Well we deal with lots of SS bolts and most are Grade 5 which is PSI rating of 125,000 PSI. A grade 8 bolt has a stronger rating with a PSI of 150,000.
so unless its attaching your drive shaft or a suspension component a SS bolt would a good choice as long as you remember to put a little dab of anti-seize on the threads.

I have no clue where you work, but the average consumer stainless bolt is grade 2 as I said and the email link explains. Naturally you can get bolts from ARP or other sources that are strong enough, but the bolts your average person is going to have access to are going to be soft to use..

MeTarzan
10-19-2012, 10:56 PM
Well I work at a Fabrication shop and we use SS fasteners alot.... we supply our Rear diff covers with SS socket head cap bolts and haven't had one pop off yet

99ishVR-4
10-20-2012, 04:23 AM
The stock coating is zinc plating with yellow chromate. You can take them all to a plating shop and they will strip and replate them for you. The average price I have found is around $75 for 10lbs and that is usually the minimum order they will do. So you would have to do it in one big batch job maning your car will be in pieces for a week. You can also get them done in a clear chromate which just looks silver, and if you polish up all your bolts before you take them, the shinier they will be when the come back. The zinc layer will show defects through the coating so if your bolt is half rusted away, it will still look bad.

While it is harder to find, a comination of tin-zinc or zinc-nickel plating gives you almost double the corrosion resistance as zinc alone and they still have a nice silver appearance.

Eastwood and caswell both sell kits to do it yourself, obviously the benifit is that you can go at your own pace and not have everything taken apart at once. But be prepared for some tedious work.

If you go with any of the above options, absolutely make sure that the plater you use bakes after coating to relieve any hydrogen embrittlement. Especially any suspension related fasteners. Any time you combine acid(whats used to pickle before plating) to with high strenght steel, there is a risk of hydrogen seeping into the metal and can cause the bolt to fail. Baking for a certain time relieves this usually.

I would recommend any of these options over ss replacements. This way you get to keep your factory hardware that was selected specifically for your car. It seems 90% of the bolts on our car have a captive washer and lockwasher, very hard to find in a universal ss bolt. Also get used to antisieze all over everything anytime you do any work. Just makes extra work for an inferior performing fastener. No offence to people that have them, they do look nice.

GTwizard
10-21-2012, 06:08 PM
OK, here ya go.
Clear zinc (and yellow) run about $45.00 to do 80 lbs of parts nuts and bolts. even the rubber hoses with metal ends can go in the tank.
Not been here in a long time. But as a builder, we do every single nut, bolt bracket and what ever. Done an entire car with yellow as well.
This is our curent 850 HP build. So everything must be right. Plated part not reachable for cleaning are all clear coated. Nut and blotls clear coated after assembly.
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6076.jpg
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6075.jpg
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6073.jpg
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6069.jpg
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6031.jpg
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6029.jpg
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6049.jpg

99ishVR-4
10-21-2012, 06:59 PM
OK, here ya go.
Clear zinc (and yellow) run about $45.00 to do 80 lbs of parts nuts and bolts. even the rubber hoses with metal ends can go in the tank.
Not been here in a long time. But as a builder, we do every single nut, bolt bracket and what ever. Done an entire car with yellow as well.
This is our curent 850 HP build. So everything must be right. Plated part not reachable for cleaning are all clear coated. Nut and blotls clear coated after assembly.
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6076.jpg
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6075.jpg
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6073.jpg
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6069.jpg
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6031.jpg
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6029.jpg
http://i498.photobucket.com/albums/rr343/GTwizard/DSCF6049.jpg

Those parts look great, where are you located to get that pricing? I have a big batch of parts and all the places I have contacted are much more expensive than what you said.

GTwizard
10-21-2012, 09:02 PM
Ask for Barrel plating. Parts that really don't fit in the barrel will be hung most times at no extra charge.
Ask for a "Lot charge" and the "number of lb.s" they can run in a lot.

Greg E
11-08-2012, 03:01 PM
Great timing for this thread. I have an entire cars worth of bolts to get replated. The bin weighs 75lbs so $45-$55 to get everything plated is a great deal! Better than sanding and painting each piece. Painting can come off while torquing the bolts during re-installation.

GTWizard who did your plating?

TurboSinceBirth
11-08-2012, 10:42 PM
I thought it was much more expensive to do plating. I will have to check into it then.

stealthknight619
11-08-2012, 11:32 PM
This is great info. I am doing an engine bay restoration with my new engine install and would love to just pick up my old and make look like these. I guess a bolt inventory is recommended before trowing in all together. By the way is there a mitsu bolt & nut part list spread sheet out there for our cars??

Sent from my MB855 using Tapatalk 2

DrGonzo
11-09-2012, 10:56 AM
@GTWizard - So the plating company charges by the lbs? So fill a box, weight it and they will plate whatever is in there regardless of it being hung or tanked? I'm really liking this is true!!!

blackandblu
11-09-2012, 09:59 PM
The process is Zinc Barrel plating- cost varies greatly by area

GTwizard
11-13-2012, 11:48 AM
Also keep in mind that plate shops most times are in those parts of large cities that we do not like to go to.
Most often the south side. LOL.
Those will be older shops, but will for sure have the best prices. these older shops most times DO NOt have a web site.
So try the old yellow pages. I know. Some of you are saying "what the hell are yellow pages?". LOL.

DrGonzo
02-06-2013, 09:57 AM
Just bumping this back up.

I got a hold of a local plater here in NC. They do barrel plating at $50.00 for max 50lbs. Basically that is their lot charge for making a single run. They were the only ones I could find within decent driving distance of me.

http://unitedmetalfinishing.us

If you have any questions shoot them an email at info@unitedmetalfinishing.us. Denise responded back to all my questions really fast.

So I'm in the process of cleaning all my parts now and hope to drop off a load to them in the next couple weeks. I have a lot of parts to clean and run through the blasting cabinet!!!