My LCD screen project, boost, WBO2, Knock, etc

**BlackStealth** · 12-30-2017, 01:39 PM

http://lcdbc.xp3.biz/updates/UPDATE371.zip
Uses new intake air temperature table as generated by the MUT2 scan tool.

Anyone with a 1996 or newer 3/S, and their car is equipped with ABS, the ABS Menu is now available to you. Please report back with your ABS HEX ID, as I only have a non-turbo 1996 ABS HEX ID available to me (B016).

**2fnloud** · 01-04-2018, 11:06 AM

Originally Posted by BlackStealth

Tip: the wire harness or pigtail connector is hard to insert on these Chinese GM 3 BAR pressure sensor. I found it easier to disassemble the harness and insert one pin at a time.

Wire color information:
Red=5V
Green=Signal
Yellow=Ground

I was tinkering with the pins due to the plug not plugging in without disassembling the plug first today. I noticed that the pins were bent, I straightened them up and now I can plug in the pigtail without taking the whole thing apart. Something to look into.

**BlackStealth** · 01-17-2018, 01:10 PM

http://lcdbc.xp3.biz/updates/UPDATE372.zip

Uses the factory barometer sensor to keep the pressure sensor zero'd. Some pressure sensors are sensitive to atmospheric changes, if this is the case for you, go to config menu and look for "Allow Barometer Compensation" and set to yes. To zero out or calibrate your pressure sensor, you will find this next to the Peak PSI menu.

**j2k4** · 01-17-2018, 06:28 PM

Page won't load ATT...I'll check back.

Thanks, Antero!

**j2k4** · 01-18-2018, 06:15 PM

Got it.

Thanks again, Antero.

**BlackStealth** · 08-25-2018, 11:11 AM

Anyone that is running version 3.xx can upgrade to version 4.00 firmware. This new version supports all 8 computers, such as:
1. Engine Computer
2. Electronic Suspension Computer
3. Digital Climate Control Computer
4. ETACS Computer
5. ABS Computer
6. Cruise Control Computer
7. SRS Airbag Computer
8. Automatic Transmission Computer

By default the config menu has the LCDBC Add on = disabled. To read all 8 computers a new cable w/ additional hardware is required.
http://lcdbc.xp3.biz/updates/UPDATE400.zip

I only have my prototype at the moment, and waiting on parts to be delivered before I make the LCDBC Add on available.

**Unlogic** · 08-26-2018, 01:28 PM

Sounds great!

**CoreyB** · 08-28-2018, 08:43 AM

Awesome, this is still one of my favorite mods.

**j2k4** · 07-23-2019, 09:31 AM

Antero, don't recall if I mentioned this problem before, but-

I'm definitely behind on my updates, I realize, but as of a few years ago - once I considered the LCDBC sorted - the boost alarm decided to sound whenever boost exceeded about 10 psi or so.

It's not super-objectionable, but my one or two attempts to reset the tone to sound at 14/15 psi were non-operative.

Any ideas?

**BlackStealth** · 07-23-2019, 06:06 PM

Originally Posted by j2k4

Antero, don't recall if I mentioned this problem before, but-

I'm definitely behind on my updates, I realize, but as of a few years ago - once I considered the LCDBC sorted - the boost alarm decided to sound whenever boost exceeded about 10 psi or so.

It's not super-objectionable, but my one or two attempts to reset the tone to sound at 14/15 psi were non-operative.

Any ideas?

Yes, that problem has been fixed. Just put the latest software on it.
http://lcdbc.xp3.biz/updates/UPDATE412.zip