Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: FINALLY getting my Jester's Flash ECU installed

  1. #1
    Monogamous Gigolo verified
    Join Date
    Sep 2010
    Owner Since
    October 2009

    Location
    Ithaca, Mi.
    Posts
    2,755
    Blog Entries
    3
    Thanks
    605
    Thanked 190 Times in 131 Posts

    FINALLY getting my Jester's Flash ECU installed

    The ECU is a 98-99 TT, the car is a 94 Stealth R/T TT. I have a conversion harness but I am going though and checking it.

    I found this link:
    https://www.3swiki.org/ECU:_94-95_TT...l_Spec_Pinouts

    And it has been helpful other than the identity of the O2 Sensors, I am needing help because I only know of the:

    Front Bank Pre-cat
    Rear Bank Pre-cat

    This is where I need help right now, here is my spreadsheet:

    Pin 1 Number 1 Injector
    Pin 2 Number 3 Injector*
    Pin 3 Number 5 Injector*
    Pin 4 Stepper Motor Coil A1 (Idle Air Control Motor)
    Pin 5 Stepper Motor Coil B1 (Idle Air Control Motor)*
    Pin 6 EGR Solenoid
    Pin 7 Fuel Pressure Solenoid
    Pin 8 MFI Relay: Fuel Pump
    Pin 9 Evaporative Emission Purge Solenoid
    Pin 10 Ignition Power Transistor Unit A (1 & 4)
    Pin 11 Ignition Power Transistor Unit C (3 & 6)
    Pin 12 MFI Relay: Power Supply
    Pin 13 Ground (in)
    Pin 14 Number 2 Injector
    Pin 15 Number 4 Injector
    Pin 16 Number 6 Injector
    Pin 17 Stepper Motor Coil A2 (Idle Air Control Motor)
    Pin 18 Stepper Motor Coil B2 (Idle Air Control Motor)
    Pin 19 Volume Air Flow Sensor MFI Reset Signal
    Pin 20 Fan Motor Relay (Hi)
    Pin 21 Fan Motor Relay (Lo)
    Pin 22 Air Conditioning Relay
    Pin 23 Ignition Power Transistor Unit B (2 & 5)
    Pin 24 Electric Load Switch
    Pin 25 Power Supply
    Pin 26 Ground (in)
    Pin 31 Fuel Pump Relay 2
    Pin 32 Turbocharger Wastegate Solenoid
    Pin 33 Not Used
    Pin 34 Muffler Mode Change Over Switch
    Pin 35 Valve Opened Or Closed Indication Signal
    Pin 36 Check Engine Malfunction Indicator Light
    Pin 37 Power Steering Pressure Switch
    Pin 38 MFI Relay: Power Supply
    Pin 39 Not Used
    Pin 40 Not Used
    Pin 41 Turbo Meter
    Pin 42 Not Used
    Pin 43 Not Used
    Pin 44 Antilock Braking Signal Input
    Pin 45 Air Conditioning Switch 1*
    Pin 46 Not Used
    Pin 51 Not Used
    Pin 52 Ignition Timing Adjustment Terminal
    Pin 53 Not Used
    Pin 54 Not Used
    Pin 55 Not Used
    Pin 56 Data Link Connector
    Pin 57 Not Used
    Pin 58 Engine Ignition Signal
    Pin 59 Air Conditioning Switch 2
    Pin 60 Right bank o2 sensor(cali precat) *CALI ONLY RIGHT?*
    Pin 61 Not Used
    Pin 62 Data Link Connector
    Pin 71 Ignition Switch - ST (Starter Relay)
    Pin 72 Intake Air Temperature Sensor
    Pin 73 Not Used
    Pin 74 Oxygen Sensor Heater *WHAT ONE?*
    Pin 75 Oxygen Sensor (Cali Pre-cat?) *IS IT A CALI-SPEC?*
    Pin 76 Oxygen Sensor Front
    Pin 77 Oxygen Sensor Heater *THIS IS THE OPTION W/B O2 WITH CHROME*
    Pin 78 Knock Sensor
    Pin 79*Left bank Oxygen sensor (Cali Pre-cat) *CALI ONLY RIGHT?*
    Pin 80 Back-Up Power Supply
    Pin 81 Sensor Impressed Voltage
    Pin 82 Ignition Switch IG*
    Pin 83 Water Temperature Sensor
    Pin 84 Throttle Position Sensor
    Pin 85 Barometric Pressure Sensor*
    Pin 86 Vehicle Speed Sensor
    Pin 87 Closed Throttle Position Switch
    Pin 88 Camshaft Position Sensor
    Pin 89 Crankshaft Position Sensor
    Pin 90 Volume Air Flow Sensor
    Pin 91 Park/Neutral Position Switch (NLTS Option)
    Pin 92 Ground Sensor


    I also looked through the service manual sheets that are on Stealth316's site, and those didn't list the pin out for "data ink connections" and grounds, or knock sensor.


    Can anyone help me with this?

  2. #2
    Forum User Not Verified
    Join Date
    Sep 2010
    Owner Since
    2001

    Location
    Medford OR
    Posts
    1,420
    Thanks
    5
    Thanked 602 Times in 302 Posts
    Are you looking for a pinout for the car or the ECU?


    Real Performance Automotive (541)816-4500 www.FB.com/RealPerformanceAuto

  3. #3
    Monogamous Gigolo verified
    Join Date
    Sep 2010
    Owner Since
    October 2009

    Location
    Ithaca, Mi.
    Posts
    2,755
    Blog Entries
    3
    Thanks
    605
    Thanked 190 Times in 131 Posts
    ECU's, I have a couple sources now, and will update my findings

  4. #4
    Monogamous Gigolo verified
    Join Date
    Sep 2010
    Owner Since
    October 2009

    Location
    Ithaca, Mi.
    Posts
    2,755
    Blog Entries
    3
    Thanks
    605
    Thanked 190 Times in 131 Posts
    Here is what I have so far:

    Spreadsheet

    Using a 99 ECU in a 94 Stealth R/T turbo

  5. #5
    Send me your email address I'll give you the pin out info.

  6. The Following User Says Thank You to BlackStealth For This Useful Post:


  7. #6
    Monogamous Gigolo verified
    Join Date
    Sep 2010
    Owner Since
    October 2009

    Location
    Ithaca, Mi.
    Posts
    2,755
    Blog Entries
    3
    Thanks
    605
    Thanked 190 Times in 131 Posts
    OK, I have my harness back from Antero, and ready to modify my ROM to be exactly like my Stock ROM minus EGR valve and setting up NLTS. Is the 91-95 fed.bin is all set for stock 94 Stealth? Or is there some minor changes needed. I checked and the Active Exhaust is enabled.

  8. #7
    Monogamous Gigolo verified
    Join Date
    Sep 2010
    Owner Since
    October 2009

    Location
    Ithaca, Mi.
    Posts
    2,755
    Blog Entries
    3
    Thanks
    605
    Thanked 190 Times in 131 Posts
    Does the bracket that mounts the ECU to the center console come off of the ECU to use with the Chrome ECU?

  9. #8
    Forum User
    Join Date
    Oct 2011
    Owner Since
    2007

    Location
    Sundsvall, Sweden
    Posts
    928
    Thanks
    327
    Thanked 119 Times in 77 Posts
    Nope at least it didn't on mine so I had to build my own bracket.


  10. #9
    Monogamous Gigolo verified
    Join Date
    Sep 2010
    Owner Since
    October 2009

    Location
    Ithaca, Mi.
    Posts
    2,755
    Blog Entries
    3
    Thanks
    605
    Thanked 190 Times in 131 Posts
    My Chrome ECU has two tabs on it like this:



    I was wondering if the bracket on my existing ECU detaches from my current ECU and can be attached to the Chrome ECU?

  11. #10
    Mad JDM Tite
    Join Date
    Sep 2010
    Owner Since
    2004

    Location
    STL
    Posts
    624
    Thanks
    6
    Thanked 88 Times in 65 Posts
    The brackets are riveted on if my memory serves.

  12. The Following User Says Thank You to 95gto For This Useful Post:


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
The 3000GT/Stealth/GTO Web History Project
3000gt.com
3000GT / Stealth International WWWboard Archive
Jim's (RED3KGT) Reststop
3000GT/Stealth/GTO Information and Resources
Team 3S
3000GT / Stealth / GTO Information
daveblack.net
3000GT/Stealth/GTO Clubs and Groups
Michigan 3S
MInnesota 3S
Wisconsin 3S
Iowa, Nebraska, Kansas 3S
North California 3000GT/Stealth
United Society of 3S Owners
3000GT/Stealth/GTO Forums
3000GT/Stealth International
3000GT/Stealth/GTO Event Pages
3S National Gathering
East Coast Gathering
Upper Mid-West Gathering
Blue Ridge Gathering